Nemco, Inc. 56050-3 Operating instructions

Brand: Nemco, Inc.

Model: 56050-3

Type: Operating instructions

This manual is also suitable for

Nemco, Inc. 56050-3 is a compact, heavy duty electric can opener designed for use in foodservice establishments. It features a quick-release, quick-change cutter assembly for easy cleaning and maintenance. The unit can open up to 50 cans per day, depending on usage, and is suitable for opening cans up to No. 10 can size. The cutter is designed to last up to 2500-5000 cans, depending on handling and actual cans used. The unit also features a dishwasher safe design for easy cleaning.

#41

#20

#16

#37

• Recommended Daily Use - maximum up to 50 cans

per day depending on usage (type of cans being

opened up to No.10 can size).

• If used according to recommended daily use and

manual instructions, the cutter should last up to 2500-

5000 cans depending on handling and actual cans used.

• If you open both ends of can for recycling, please

double your usage figure.

1. Place can gently as shown. Be sure that can

touches the body of the can opener and the

U-shaped pin of the Cutter Housing #27 is

over the lid seam.

2. Lower can opener head GENTLY on can. Do

not slam down. Push down side handle to lock

can in position.

3. Turn top handle in a CLOCK-WISE direction.

OPERATING INSTRUCTIONS

WARNING

Over-rotating beyond the inital

seam cut may cause metal slivers. Incision point

may be sharp. Train operators when to stop cutting

and how to remove lid safely.

1. UNLOCK SIDE HANDLE #20. Slightly press Gripper

Housing #7 to pull out Side Locking Pin #16.

2. Tilt back Gripper Housing #7. Clean Gripper.

3. Pull out Cutter Housing Assembly #41. Rinse under

tap and clean food debris with brush.

To re-assemble:

1. Insert Cutter Housing Assembly #41.

2. Return Gripper Housing #7 to closed position.

3. Slightly press Gripper Housing #7 to re-insert the

Side Locking Pin #16 (ENSURE SIDE HANDLE #20 IS

UNLOCKED)

Do not tamper with

factory settings or else

warranty will be void.

CLOCK-WISE

Pull out Can Sitter #37 for

regular cleaning.

CLEANING INSTRUCTIONS

FOR INSTITUTIONAL USE ONLY

• Inspect and change cutters regularly.

• Cutter area must be kept clean at all times. Do not allow

food and debris to dry up and accumulate in this area.

• Do not over rotate top handle to cut beyond the initial

seam cut as this may cause metal slivers. If on the first

cut the lid does not open (check carefully as lid may be

opened, however, due to lid being vacuum sealed it may be

difficult to lift lid off) do not continue to rotate handle.

LOCK

UNLOCK

Printed in Canada Nov. 20, 2006

PRODUCT WARRANTY

Except as otherwise provided below, Nemco Food Equipment, LLC and including its manufacturer Crown Ware Manufacturing

Inc. (“Nemco”) warrants, to the original user, its can opener products (other than cutters, bearings and gripper) to be free of

mechanical defects in material and workmanship under “normal use” (defined below) for the shorter of the following periods: (a)

one (1) year from the date placed in service by the original user, or (b) 18 months from the date of shipment from its factory. The

warranty provided herein shall be limited to parts and labor. Any determination that a product is defective or covered by this

warranty, shall be made by Nemco, in its sole discretion. The determination of whether to repair or replace a defective, covered

product, or to refund the purchase price for the product, will be at Nemco’s sole discretion. This warranty does not cover

products used outside the United States, or damages caused by accident, misuse, negligence of any person other than Nemco,

fire, flood or other casualty. Any alteration to the product or unauthorized repair voids this warranty. For purposes of this

warranty, the phrase, “normal use” shall mean the use of the product in connection with food in accordance with the product

manual accompanying the product.

Nemco shall be responsible only for repairs or replacements of defective parts performed by Nemco’s authorized service

personnel. Authorized service agencies are located in principal in cities throughout the continental United States, Alaska and

Hawaii.

THE FOREGOING WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR

IMPLIED. NEMCO EXPRESSLY DISCLAIMS ANY IMPLIED WARRANTY THAT ANY OF ITS PRODUCTS IS

MERCHANTABLE, FIT FOR A PARTICULAR PURPOSE, OR DOES NOT INFRINGE ON THE RIGHTS OF ANY

THIRD PARTY. THE FOREGOING WARRANTY SHALL BE NEMCO’S SOLE AND EXCLUSIVE OBLIGATION.

ANY PERSON’S (BUYER, USER OR OTHERWISE) EXCLUSIVE REMEDY AGAINST NEMCO, AND NEMCO’S

SOLE OBLIGATION, FOR ANY AND ALL CLAIMS, WHETHER FOR BREACH OF CONTRACT, WARRANTY,

TORT(INCLUDING WITHOUT LIMITATION NEGLIGENCE), OR OTHERWISE, SHALL BE LIMITED TO NEMCO

REPAIRING OR REPLACING THE PRODUCT, OR, AT NEMCO’S OPTION, REFUNDING THE PURCHASE PRICE

THEREFORE. IN NO EVENT SHALL NEMCO HAVE ANY LIABILITY FOR INCIDENTAL, SPECIAL OR

CONSEQUENTIAL DAMAGES. Any person desiring to make any claim against Nemco must do so within six (6) months after

expiration of the applicable warranty period, or such claim shall be forever barred.

Quick-Release

Quick-Change Cutter

PURCHASE A SPARE

CUTTER HOUSING

FOR NO DOWN-TIME

Exclusively from

Product Manufactured in Canada by

Limited Warranty applies if the following instructions are followed:

IMPORTANT

Side Pin groove must be fully

inserted for proper cutting.

wwwwww. nemcofoodequi p. com. nemcofoodequip. com

"EXCEEDING YOUR EXPECTATIONS"

301 Meuse Argonne

Hicksville, Ohio 43526

1. 800. 782. 6761

301 Meuse Argonne

Hicksville, Ohio 43526

1. 800. 782. 6761

www.canopeners.ca

RECOMM. HANDLE TURNS:

Can Size Diameter Handle turns

#2 3” 3 revolutions

#5 5” 5 revolutions

#10 6” 6 revolutions

Be sure the bent side

of Can Sitter #37 is

facing down.

Rinse cutter side

under tap. Brush for

thorough cleaning.

COMPACT COMPACT

COMPACT NEW MODEL

GEARLESS AND FEARLESSGEARLESS AND FEARLESS

GEARLESS AND FEARLESS

INSTITUTIONAL USE ONLY

DISHWASHER SAFE

Tighten

Loosen

[Left hand bolt]

RIGHT WAY

HOLLOW SIDE

DOWN

1. Hold Cutter Shaft #26 with wrench and loosen

Cutter Locking Bolt #31(left hand thread) with

another wrench by turning clockwise.

2. Remove Cutter Washer #30 and Cutter Spacer #29

and Cutter #28.

3. Replace with new Cutter #28.

4. Reverse steps 2 and 1 to re-assemble.

REPLACING CUTTER

FROM CUTTER ASSEMBLY

IMPORTANT

Cutter edge #28

must face

Right Way as

shown in diagram.

COMPACT REPLACEMENT PARTS

For more information on part orders or repair

service, contact NEMCO Food Equipment at

1-800-782-6761

PRODUCT SERVICE

Nemco has a staffed service department and we believe prompt service is extremely important to

our customers. Therefore, we request all product service inquiries be handled in the following

manner:

(1) The end user should call Nemco Customer Service with the company name, address,

phone number, model number, serial number (if applicable), Nemco Sales Order

number or Dealer Purchase Order Number and the nature of the problem (the “Claim

Information”).

(2) The Nemco Customer Service Department will decide on the most appropriate

course of action. If Nemco determines that it must inspect a product, the following

procedure will be followed.

The end user will obtain a Return Goods Authorization number from Nemco Customer Service to

return the product to Nemco for inspection. Please be sure to use this number on the box and on

paperwork sent with the unit. Return the unit to Nemco. The Nemco Service Department will

determine if the problem is covered by the foregoing warranty. If so, Nemco will repair the unit and

return it to the end user. If the unit is determined not to be covered by the foregoing warranty, the

dealer will be contacted to determine the next course of action.

Model Description No. 56050-1, 56050-2, 56050-3

PARTS DIAGRAM

Optional

Under Clamp Assembly #42

Optional Spare

Cutter Assembly #41

Includes 6, 26,27, 28, 29, 30, 31

Optional Spare

Side Pin Assembly #43

No.

Name

Top Handle Top Cover

Top Handle Knob

Top Handle Knob Screw

Top Handle

Handle Screw

Bearings

Gripper Housing

Gripper Shaft

Gripper

Bushing

Locking Bridge Mechanism

Locking Bridge Pin

Pan Head Set Screw

Gripper Housing Spring

Side Locking Pin

Bushing

Side Handle Shaft

Side Handle

Mechanism Housing

Part #

56030

56031

56032

56033

56034

56027

56035

56036

56028

56037

56038

56039

56040

56041

56042

56043

56044

56045

56046

56047

56048

Name

Ball Setscrew

Adjusting Nut

Rubber Depth Control

Adjusting Bolt

Cutter Shaft

Cutter Housing

Cutter

Cutter Spacer

Cutter Washer

Cutter Locking Bolt

Rubber PIpe Bumper

Square Pipe

Rubber Pipe End

Side Locking Pin Chain

Top Table Base

Can Sitter

Under Clamp

Table Clamp Bolt

Anti-Slip Rubber Pad

Cutter Housing Assembly

Under Clamp Assembly

Side Pin Assembly

Part #

56049

56051

56052

56053

56054

56055

56029

56024

56056

56057

56058

56059

56060

56026

56061

56062

56063

56064

56065

56022

56023

56068

ELIMINELIMIN

ELIMIN

TE DOTE DO

TE DO

WN-TIMEWN-TIME

WN-TIME

Purchase a spare Cutter

Assembly for quick

replacement.

Nemco, Inc. 56050-3 Operating instructions

Brand: Nemco, Inc.

Model: 56050-3

Type: Operating instructions

This manual is also suitable for

Download PDF

report

Nemco, Inc. 56050-3 Operating instructions

This manual is also suitable for

Nemco, Inc. 56050-3 Operating instructions

Related papers

Other documents