Bosch Axxis WTA3510UC User manual

Category
Tumble dryers
Type
User manual
A
XXIS
WTA 3510
Electric Vented Dryer
A
XXIS
WTL 5410
Electric Condensation Dryer
   
 
Internet:
http://boschappliances.com
  
Use and Care Manual
IMPORTANT SAFETY INSTRUCTIONS 4. . . . . .
GROUNDING INSTRUCTIONS 5. . . . . . . . . . . . . .
ABOUT YOUR DRYER 6. . . . . . . . . . . . . . . . . . . . .
GETTING TO KNOW YOUR DRYER 6. . . . . . . . .
ENERGY SAVING TIPS 7. . . . . . . . . . . . . . . . . .
OPERATING TIPS 7. . . . . . . . . . . . . . . . . . . . . . .
BEFORE USING FOR THE FIRST TIME 7. . . . . .
GETTING STARTED 7. . . . . . . . . . . . . . . . . . . . . . .
CYCLE SELECTION CHART
(Recommendations) 8. . . . . . . . . . . . . . . . . . . . . . . .
ELECTRONIC AUTO DRY CYCLES 8. . . . . . . . . .
OPERATION 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CARE and CLEANING 11. . . . . . . . . . . . . . . . . . . . . .
Lint Filter 11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Heat Exchanger (WTL models only) 11. . . . . . . .
Moisture Sensor 12. . . . . . . . . . . . . . . . . . . . . . . . .
Frost Protection (WTL models only) 12. . . . . . . .
SERVICE and REPAIR 12. . . . . . . . . . . . . . . . . . . . .
SELF-HELP 13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
STATEMENT OF WARRANTIES
BOSCH CLOTHES DRYERS 14. . . . . . . . . . . . . . . .
Exclusions 14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation Instructions
Introduction 15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tools Needed for Installation 15. . . . . . . . . . . . . .
Parts Supplied for Installation 15. . . . . . . . . . . . .
Parts Needed for Installation 15. . . . . . . . . . . . .
Dryer Electrical Cord 15. . . . . . . . . . . . . . . . . . . . .
Grounding Instructions 15. . . . . . . . . . . . . . . . . . .
Additional Grounding Procedure 16. . . . . . . .
Electrical Receptacle 16. . . . . . . . . . . . . . . . . . . . .
Venting 16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ductwork 16. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Exhaust Vent Hood 16. . . . . . . . . . . . . . . . . . . .
Condensate Drain 16. . . . . . . . . . . . . . . . . . . . . . .
Stacking Kit 16. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Stacking Kit with Pull-out-tray 16. . . . . . . . . . . . .
Technical Data 17. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Electrical Requirements 17. . . . . . . . . . . . . . . . . .
Choosing the Location 17. . . . . . . . . . . . . . . . . . .
Minimum Installation Clearances 17. . . . . . . . . .
INSTALLATION 19. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Step 1 Unpack the Dryer 19. . . . . . . . . . . . . . . . .
Step 2 Inspect the Dryer 19. . . . . . . . . . . . . . . . . .
Step 3 Position Dryer near Installation Area 19.
Step 4 Exhaust Duct 19. . . . . . . . . . . . . . . . . . . .
Step 5 Condensate Hose Connection 20. . . . .
Step 6 Electrical 21. . . . . . . . . . . . . . . . . . . . . . . . .
Step 7 Position and Level the Dryer 22. . . . . . . .
Step 8 Connect Duct System to Dryer 23. . . . .
Step 9 Final Check List 23. . . . . . . . . . . . . . . . . . .
IMPORTANT: Before you begin read these instructions completely
and carefully.
INSTALLER: Remove the door from all discarded appliances
to avoid the danger of a child suffocating.
KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE.
(In case of change of ownership, manual should be conveyed with the dryer.)
Use and Care Manual
IMPORTANT SAFETY INSTRUCTIONS
WARNING: To reduce the risk of fire, electric shock, serious injury or death to persons when using your dryer,
follow basic precautions, including the following.
1. Bosch dryers are provided with an Use and Care
Manual and an Installation Instruction manual.
Read all instructions before using the dryer.
2. Do not dry articles that have been previously cleaned
in, washed in, soaked in, or spotted with gasoline,
dry cleaning solvents, other flammable, or explosive
substances as they give off vapors that could ignite
or explode.
3. Do not allow children to play on or in the appliance.
Close supervision of children is necessary when the
appliance is used near children.
4. Before the appliance is removed from service
or discarded, remove the door to the drying
compartment.
5. Do not reach into the appliance if the drum is
moving.
6. Do not install or store this appliance where it will be
exposed to the weather.
7. Do not tamper with the controls.
8. Do not repair or replace any part of the appliance or
attempt any service unless specifically
recommended in the user-maintenance instructions
or in published user repair instructions that you
understand and have the skills to carry out.
9. Do not use fabric softeners or products to eliminate
static unless recommended by the manufacturer of
the fabric softener or product.
10. Do not use heat to dry articles containing foam
rubber (may be labeled latex foam) or similarly
textured rubber-like materials. Foam rubber
materials can, under certain circumstances, when
heated become ignited by spontaneous combustion.
11. Clean lint screen before or after each load.
12. Keep area around the exhaust opening and adjacent
surrounding areas free from the accumulation of lint,
dust and dirt.
13. The interior of the machine and exhaust duct should
be cleaned periodically by qualified service
personnel.
14. Always be sure to unplug the dryer from the
electrical supply before attempting any service.
Disconnect the power cord by grasping the plug, not
the cord.
15. Store all laundry chemicals and aids in a cool dry
place according to the manufacturer’s instructions in
an area where children cannot reach them.
16. To reduce the risk of fire, clothes, cleaning rags, mop
heads and the like which have traces of any
flammable substance, such as vegetable oil, cooking
oil, petroleum based oils or distillates, waxes, fats,
etc., must not be placed in the dryer. These items
may contain some flammable substance(s) even
after washing, which may smoke or catch fire by
itself.
17. Do not sit on top of the dryer.
18. To reduce the risk of fire or electrical shock, DO NOT
use an extension cord or an adapter to connect the
dryer to the electrical power supply.
19. The dryer must only be used for its intended
purpose.
20. Always check and empty pockets of any objects that
may have been forgotten. Cigarette lighters, in
particular, present a hazard that can be avoided by
this process.
IMPORTANT SAFETY INSTRUCTIONS (continued)
21. Replace worn power cords and/or loose plugs.
22. Do not operate the dryer with any guards and/or
panels removed.
23. Do not operate the dryer with missing or broken
parts.
24. Do not bypass any safety devices.
25. Do not use plastic or non-metal flexible duct with this
dryer. Plastic or non-metal flexible duct presents
a potential fire hazard.
26. Do not operate this dryer until you are sure the dryer
has been installed according to the INSTALLATION
INSTRUCTIONS and installation and grounding are
in compliance with all local codes and/or other
applicable codes and requirements.
27. Failure to install, maintain and/or operate the dryer
according to the manufacturer’s instructions may
result in conditions which can lead to bodily injury
and/or property damage.
Notes: A The IMPORTANT SAFEGUARDS and WARNINGS presented in this manual do not cover all
possible conditions that may occur. Common sense, caution and care must be exercised when
installing, maintaining or operating the dryer.
B Always contact your dealer, distributor, service agent or the manufacturer about any problems or
conditions that you do not understand.
SAVE THESE INSTRUCTIONS
GROUNDING INSTRUCTIONS
This appliance must be grounded. In the event of
malfunction or breakdown, grounding will reduce the risk
of electric shock by providing a path of least resistance
for the electric current. This appliance is equipped with
a cord having an equipment-grounding conductor and
a grounding plug. The plug must be plugged into an
appropriate outlet that is properly installed and grounded
in accordance with all local codes and ordinances.
WARNING – Improper connection of the equipment-
grounding conductor can result in a risk of electric shock.
Check with a qualified electrician or serviceman if you
are in doubt as to whether the dryer is properly
grounded.
DO NOT modify the plug provided with the appliance –
if it will not fit the outlet have a proper outlet installed
by a qualified electrician or exchange the cord with
an appropriate one rated for the dryer.
Figure 1.
ABOUT YOUR DRYER
Congratulations on having selected a Bosch clothes
dryer, the choice of those that demand exceptional
performance from their clothes dryer. The Bosch
WTA 3510 and WTL 5410 dryers offer the following
standard features:
High Efficiency Precision Drying System with
Duotronic
Stainless Steel Drum
Exceptionally Quiet Operation
Condensation Drying allows vent free operation
Reverse Tumble Action
Sensor controlled Auto Cycles with up to 6 drying
levels per fabric type and Timed Cycles from 10 to
90 minutes.
i
Exchangeable Control Panel inserts in French and
Spanish.
If you desire to change the language of the control
panel to either French or Spanish please contact
customer service at 1-800-944-2904.
Please specify dryer model number and language
of fascia insert desired.
GETTING TO KNOW YOUR
DRYER
Above you will find an illustration, Figure 1, showing the
location of the following:
1 Door with lint filter
2 Button to open the maintenance flap
(WTL models only)
3 Heat Exchanger/Inlet panel (WTL models only)
4 ‘‘On/Off’’ button
5 ‘‘Door’’ button
6 ‘Start’’ button
7 ‘‘Delicates’’ button
8 ‘‘End of Cycle Signal’button
9 ‘‘Cycle Time Minutes’button
10 Time Cycles Selector Knob
11 Auto-Cycles Selector knob
12 Indicator lights for program selected
13 Indicator lights for time program selected
14 Lint Filter Cleaning indicator
15 Indicator lights for buttons
16 ‘‘Time Remaining’’ Display
17 Moisture Level indicator lights
18 Rating Plate location.
ENERGY SAVING TIPS
To save energy, time and money, Bosch recommends
the following:
Always spin dry the laundry in the washer at the
highest recommended speed for the fabric type.
The highest spin speed will result in a dryer load and
shorten the drying time and amount of energy
required to dry the load.
Spin dry delicate washing before tumble drying.
Load the dryer properly. Do not exceed the maximum
load (see CYCLE SELECTION CHART).
Always clean the lint filter after each use of the dryer.
OPERATING TIPS
Follow the fabric care labels on the clothing.
Avoid very small loads. When only one or two items
need drying, add a few similar items to improve
drying efficiency.
Do not mix heavyweight and lightweight clothing.
Do not dry wool or fabrics with a wool content
Do not dry fabrics that do not allow the free passage
of air (for example, GORETEX)
Do not dry delicate fabrics such as, silk, synthetic net
curtains, etc.
BEFORE USING FOR THE FIRST TIME
Before beginning to use your dryer for the first
time:
1. Check to make sure that the voltage on
which the dryer is to operate is the same as
shown on the rating plate.
2. Wipe the interior of the drum with a damp cloth.
3. Thoroughly inspect the dryer for cosmetic damage.
GETTING STARTED
Below, in order to get started, you will find a summary of
how to operate the clothes dryer. Also, refer to the
CYCLE SELECTION CHART, Table 1.
Turn On the Dryer
Press the ‘‘On/Off’’ button. The indicator light will
become illuminated and the indicator above the
‘Start’’ button will begin to flash.
Check the Lint Filter
The lint filter, located in the door, should be cleaned
after or before each load.
Load the Dryer
Load the items in the dryer.
Add Fabric Softener Sheet
If a fabric softener sheet is to be added it should
be done after loading the dryer.
Close the Dryer Door
Select Cycle Desired
See CYCLE SELECTION CHART, Table 1, and
following section titled OPERATION for program
recommendations.
Select Additional Functions (if desired)
See following section titled OPERATION.
Press the ‘Start’Button
The ‘Start’’ indicator lamp will stop flashing and the
dryer will start. If one of the Auto-Cycles have been
selected the Duotronic system will monitor the
moisture level and display the progress of the drying
in the ‘‘Moisture Level Indicator Lights.’If a timed
cycle has been selected the minutes remaining will
be displayed in the ‘‘Cycle Countdown Display.’’
The cycle will continue to the end, when the ‘‘End’
indictor lamp will become illuminated. And, if the
‘‘End of Cycle Signal’’ has been selected a signal will
sound. – See following section OPERATION on how
to set or turn of the ‘‘End of Cycle’’ signal.
Depress the ‘‘DoorButton
The door will open.
Remove the Laundry from the Dryer
Clean the Lint Filter
Turn Off the Dryer
Depress the ‘‘On/Off’’ button.
CYCLE SELECTION CHART (Recommendations)
   
Drying Level Setting
Cotton or linen items (whites and coloreds), full load *
Note: For heat-sensitive items press the ‘‘Delicates’’ button.
Regular/Cott.
Bed and table linen, towels for laundry which will be ironed with rotary iron or
finished by air drying
Damp dry
Bed and table linen, towels, T-shirts, work
clothes
for laundry which will be ironed with a steam iron Econo dry
T-shirts, trousers, work clothes, underwear for laundry which will be ironed lightly, or not at all Light dry
Bath towels, tea towels, hand towels, bed
linen, underwear, cotton socks
for laundry which will not be ironed Regular dry
Bath towels, tea towels, hand towels, bed
linen, underwear, cotton socks
for thick, multi-layered materials which will not be
ironed
Very dry
Flannel dressing gowns and bed linen particularly thick or multi-layered materials Extra dry
Permanent Press items (non-iron items) made of synthetic and mixed fibers and non-iron
cottons,
1
/
2
load *
Note: For heat-sensitive fabrics press the ‘‘Delicates’’ button.
Permanent Press
Trousers, skirts, dresses, shirts for laundry which will be ironed with a steam iron Econo dry
Synthetic trousers, skirts, dresses, shirts,
blouses, leggings and sportswear
for laundry which will be ironed either lightly, or
not at all
Light dry
Shirts, blouses, sportswear for laundry that will not be ironed Regular dry
Bed and table linen, jogging suits (sweats) for thick, multi-layered materials which will not be
ironed
Very dry
Parkas (anoraks), bed covers particularly thick or multi-layered materials Extra dry
Timed Cycles
Pre-dried fabrics with low moisture content and separate, small items Heated Dry: 10–90 min.
All fabrics or items needing freshening, tumbles without heat Air Fluff: 10–90 min.
*Refers to full and half loads from Bosch tumble action clothes washer.
Table 1.
OPERATION
Below you will find a more detailed explanation of the
operation of your dryer:
1. Turn the dryer on
Depress the ‘‘On/Off’’ button. The indicator light
above the button will become illuminated indicating
that the machine is on and the light above the ‘Start’’
button will flash.
2. Check the Lint Filter
The lint filter, located in the door, should be cleaned
after or before each load. Check the lint filter and if it
was not cleaned after last use clean it now. Cleaning
the filter will shorten drying times and save energy.
Figure 2.
3. Load the dryer
For best results it is recommended that the drying
load be sorted by fabric type and desired dryness
level. Also, close all zippers, hooks and eyelets and
tie loose belts and apron strings, etc. before placing
in the dryer.
a. Depress the ‘‘Door’’ button. The door will open
and the drum light will turn on.
b. Check the drum interior for foreign objects or
pets and remove any used fabric softener sheets.
c. Place laundry items to be dried loosely into the
drum of the dryer.
4. Add Fabric Softener Sheet, if desired
If a fabric softener sheet is to be added it should be
done after loading the dryer and before the dryer and
load become warm. This will prevent greasy-looking
softener stains.
5. Close the Door
Check the area around the drum opening to make
sure that nothing is caught on the edge or hanging
outside the drum and close the door making sure the
door clicks into place and is fully closed.
Note: If the door is not fully closed
the dryer will not operate.
6. Select the Drying Cycle Desired
The Bosch dryers can be operated in either the
Electronic Auto Dry Cycle mode, which uses the
Duotronic moisture sensing system, or in Time Cycle
mode, which uses a timer to control the length of the
program. See below and CYCLE SELECTION
CHART, Table 1, for program recommendations:
a. To use Electronic Auto Dry Cycles
(dryer runs until the drying level selected has
been reached) activate by turning the Cycle
Selector knob (see Figure 3) to:
i. Regular /Cott.
The Auto-Program dial should be turned to point
to the right to select Regular/Cott. settings. As
the knob is turned the lights directly above the
knob will illuminate to indicate the level of
dryness selected, from Extra dry through Damp
dry. See Table 1 for recommended settings for
type of load being dried.
or,
ii. Permanent Press
The Auto-Program knob should be turned to point
to the left to select Permanent Press settings.
As the knob is turned the lights directly above the
knob will illuminate to indicate the level of
dryness selected, from Extra dry through Econo
dry. See Table 1 for recommended settings for
type of load being dried.
Figure 3.
b. To use Time Cyles (dryer runs for selected
length of time) activate by turning the time
program selector (see Figure 4):
i. Heated Dry
The Time Cycle’s knob should be turned to point
to the right to select the Heated Dry setting. Then
depress the ‘‘Cycle Time Minutes’’ button to set
the time interval for drying. The time can be set at
10–90 minutes in 10 minute steps.
or,
ii. Air Fluff (cold)
The Time Cycle’s knob should be turned to point
to the left to select the Air Fluff setting. Then
depress the ‘‘Cycle Time Minutes’’ button to set
the time interval for drying. The time can be set at
10–90 minutes in 10 minute steps.
Note: The Auto-Program knob must be pointing
straight-up to use Time Cycles.
Figure 4.

7. Select ADDITIONAL FUNCTIONS, if desired
The additional functions available are accessible
by depressing the buttons:
‘‘Delicates’’
The ‘‘Delicates’’ button, see Figure 5, will reduce the
drying temperature and lengthen the drying time
when depressed. It is recommended that the
‘‘Delicates’’ button be depressed when drying heat
sensitive fabrics, such as, acrylics. Be sure to follow
the instructions listed on the care label instructions.
‘‘End of Cycle Signal’’
When the ‘‘End of Cycle Signal’’ button, see Figure 5,
is activated there will be a signal sounded at regular
intervals at completion of the selected program.
The volume level of the sound may be changed by
holding the button in until desired volume level is
reached. This volume level will be stored for future
use until altered.
The end of cycle signal can be switched off by
depressing the button again. The indicator light
above the button will turn off to indicate that the
signal is no longer selected.
8. Press the ‘Start’Button
Depress the ‘Start’’ button. The indicator light above
the ‘Start’’ button will become illuminated and the
machine will start. If one of the Auto Cycles has been
selected the Duotronic system will continuously
monitor the moisture level of the load and display the
progress in the ‘‘Moisture Level Indicator Lights.’’ If
a timed cycle has been selected, either Heated Dry
or Air Fluff, the minutes remaining in the program will
be shown in the ‘‘Cycle Countdown Display.’’
The program will continue to the end, when the
‘‘End’’ indicator lamp will become illuminated.
And if the ‘‘End of Cycle Signal’’ has been selected
a signal will sound.
Note: If using the Auto program at the beginning
of the cycle there will be numerous rotations
in each direction with complete stops in
between for approximately 90 seconds.
There is nothing wrong with the machine,
it is taking a reading on the moisture of the
load to determine how long to dry.
Note: If the load is not removed, the drum will,
for the following 35 minutes, rotate at brief
intervals to prevent wrinkling (Anti-Crease).
After 35 minutes this feature will cease its
function. It is recommended that the dryer
be unloaded no later than 35 minutes after
completion of program to avoid wrinkling.
Figure 5.
9. Depress the ‘‘Doorbutton
The door will open.
10. Remove the Laundry from the Dryer
11. Clean the Lint Filter
The lint filter, located in the door, should be cleaned
after each load. Cleaning the filter will shorten drying
times and save energy.
12. Turn Off the Dryer.
Depress the ‘‘On/Off’’ button.

CARE and CLEANING
The housing and control panel should only be cleaned
with a soft cloth rinsed in soapy water, or with a solvent
free, non-scouring cleaning agent.
Other areas requiring periodic cleaning or maintenance
are listed below:
Lint Filter
The lint filter should be cleaned after each use or If the
‘‘Lint Filter’ light becomes illuminated and the buzzer
sounds during operation of the dryer:
1. Immediately stop the dryer by depressing the
‘‘On/Off’’ button.
2. Depress the ‘‘Door’’ button and open the door.
3. Remove the filter.
4. Clean the filter.
5. Replace the filter.
6. Let the dryer cool down.
7. Close the door.
8. Press the ‘Start’’ button to restart the dryer.
Heat Exchanger (WTL models only)
The heat exchanger should be cleaned 3–4 times a year;
more often if used frequently. To clean the heat
exchanger:
1. With the dryer turned off and disconnected from
the electrical supply. Disconnect the power cord
by grasping the plug, not the cord.
2. Depress the ‘‘Door’’ button and open the door.
3. Press the button for opening the heat exchanger/inlet
panel, as shown in Figure 6.
Figure 6.
4. Open the panel fully.
5. Turn the retainers on each side of the heat
exchanger towards each other, in the direction of the
arrows as shown in Figure 7.
6. Remove the heat exchanger by slowly pulling it
forward and out of the dryer.
7. Clean the heat exchanger thoroughly with water.
Allow the water to run freely through the heat
exchanger. See Figure 8.
Figure 7.
Figure 8.
8. Allow heat exchanger to dry thoroughly before
reinserting into the dryer.
9. Once the heat exchanger is completely dry, reinsert it
into the dryer. The handle must be underneath the
heat exchanger. Turn the retainers back to their
original position.
10. Close the heat exchanger/inlet panel by pressing
firmly on both the upper left and right hand sides,
as shown in Figure 9, until it snaps into place.
Note: The dryer door will only be able to be closed
if the heat exchanger/inlet panel is properly
closed and locked in place.
Figure 9.

Moisture Sensor
Occasionally the moisture sensors will need cleaning,
due to a build-up of a fine layer of lime scale on the
inside of the drum. This build-up of lime scale can be
easily removed by wiping the sensors, the metal inserts
in the paddles, and the inside of the drum with a soft
cloth soaked in vinegar (use white vinegar).
See Figure 10.
Figure 10.
Frost Protection (WTL models only)
The WTL models, since they remove moisture by
condensing the water out of the air and then pumping
the water to drain, should never be installed in an area
subject to freezing. Also, if the dryer is to be transported
where it would be subjected to freezing the dryer must
be completely emptied of water before transporting.
SERVICE and REPAIR
The Bosch dryers require no special care other than the
care and cleaning noted above. If you are having
a problem with your dryer, before calling for service
please refer to Table 2, SELF-HELP section, following.
If service becomes necessary, contact your dealer or
installer or an authorized service center. Do not attempt
to repair the appliance yourself. Any work performed by
unauthorized personnel may void the warranty.
If you are having a problem with your Bosch dryer and
are not pleased with the service you have received:
First, please contact your installer or the Bosch
Authorized Service Contractor in your area and
explain to them why you are not satisfied. This will
usually correct the problem.
If after working with your installer or service person
the problem still has not been resolved to your
satisfaction, please let us know by either writing to
us at,
BSH Home Appliances
5551 Mc Fadden Avenue
Huntington Beach, CA 92649
or, calling us at,
1-800/944-2904.
Please be sure to include, if writing, or have available,
if calling, the following information:
Model Number
Serial Number
Date of Original Purchase
Date Problem Originated
Explanation of Problem
Also, if writing, please be sure to include a daytime
telephone number and a copy of the sales invoice.
You will find the model number and serial number
information on the rating plate located on the inside of
the door above the lint filter. See Figure 1.

SELF-HELP
Dryers may exhibit problems that are unrelated to a malfunction of the dryer itself. The following table may serve to
answer your question about a problem you are having without having to call a serviceman.
PROBLEM
POSSIBLE CAUSE
‘‘On/Off’’ Indicator light does not
come on
The ‘‘On/Off’’ has not been depressed.
A fuse may have blown or a circuit breaker tripped. Replace fuse or reset circuit
breaker at your fuse box/breaker box.
The plug is not correctly or only loosely inserted into the receptacle.
Dryer does not start Cycle has not been selected.
‘Start’’ button has not been depressed.
Door is not closed properly.
Room temperature is below 32 °F (0 °C)
If necessary, switch the machine off and wait 5 seconds before switching it on
again. Select the cycle again and depress ‘Start’’.
Cycle is interrupted and ‘‘Lint
Filter’’ light is illuminated and
buzzer sounds
Clean Lint Filter as described in section titled CARE and CLEANING.
(WTA models) Check exhaust vent to see if it is blocked or too long.
(WTL models) Clean heat exchanger as described in section titled CARE
and CLEANING.
(WTL models) Check air inlet to make sure it is not blocked.
Cycle is interrupted, buzzer
sounds, one or several cycle
indicators are flashing
Indicates faulty operation:
Clean the Lint Filter, check the exhaust duct length (WTA models),
Switch the dryer off, wait for it to cool down and then restart.
Drying level not reached or
drying time too long
Clean the Moisture sensors in the drum as described in section titled CARE and
CLEANING.
If there is a power failure for an extended period the cycle must be restarted.
The laundry is not dry even
though the highest drying level
has been selected
The drum is too full.
The laundry was too wet when placed in the dryer.
The room is not adequately ventilated. Make sure there is an adequate supply of
fresh air.
The lint filter is blocked and should be cleaned.
(WTA models) The exhaust vent is blocked or too long.
(WTL models) The air inlet is blocked.
Drum light does not work ‘‘On/Off’’ button has not been pressed.
Bulb has failed. For safety reasons the bulb must only be replaced by an
authorized service agent.
Following items apply only to the WTL (Condensation Electric Dryer) models
Cycle is interrupted and ‘‘E1’
appears in display
Condensate hose is blocked in some way. Turn off dryer and check hose.
Humidity level in room
increases greatly
The room is not adequately ventilated. Make sure there is an adequate supply of
fresh air.
Check air inlet to see if it is blocked.
The heat exchanger was removed but not replaced.
Table 2.

STATEMENT OF WARRANTIES BOSCH CLOTHES DRYERS
The warranties provided by BSH Home Appliances (‘‘Bosch’’) in this Statement of Warranties apply only to Bosch
Clothes dryers sold to the first using purchaser by Bosch or its authorized dealers, retailers or service centers in the
United States or Canada. The Warranties provided herein are not transferable.
LENGTH OF WARRANTY
SCOPE OF WARRANTY
1 Year Full Limited Warranty
From Date of Installation*
Bosch will repair or replace, free of charge, any
component part that proves defective under conditions
of normal home use, labor and shipping costs included.
Warranty repair service must be performed by an
authorized Bosch Service Center.
2 Year Limited Warranty
From Date of Installation*
Bosch will provide replacement parts, free of charge, for
any component part that proves defective under conditions
of normal home use, shipping costs included, labor
changes excluded.
5 Year Limited Warranty on Electronics
From Date of Installation*
Bosch will repair or replace, free of charge, any
microprocessor or printed circuit board that proves
defective under conditions of normal home use during
the second trough fifth year from the date of original
installation, labor charges excluded.
5 Year Limited Warranty on Motor
From Date of Installation*
Bosch will repair or replace, free of charge, any motor or
component part of the motor that proves defective under
conditions of normal home use for a period of five years,
labor charges excluded.
5 Year Limited Warranty on Cabinet Rust
From Date of Installation*
Bosch will replace any cabinet part, free of charge, if that
cabinet part should rust through under conditions of
normal home use, labor charges excluded.
Lifetime Limited Warranty against
Stainless Steel Rust Through
From Date of Installation*
Bosch will replace your clothes dryer, free of charge, with
the same model or a current model that is equivalent or
better in functionality if the dryer drum should rust through
under conditions of normal home use, labor charges
excluded.
* Date of installation shall refer to the earlier of the date the clothes dryer is installed or ten business days after the
delivery date.
Exclusions
This warranty does not cover service calls or repairs to correct the installation of the clothes dryer, to provide
instructions on the use of your clothes dryer, to replace house fuses or correct plumbing or the electric wiring in your
home or to repair any clothes dryer that’s use was in a manner other than what is normal and customary for home use.
In addition, the warranties provided in this Statement exclude any defects or damage arising from accident, alteration,
misuse, abuse, improper installation, unauthorized service work, external forces beyond Bosch’s control, such as fire,
flood, and other acts of God, or installation not in accordance with local electrical and plumbing codes. Labor charges
incurred in the repair or replacement of any clothes dryer after a period of one year from date of installation shall not be
covered by this warranty. Any and all replaced and/or repaired parts shall assume the identity of the original for
purposes of the applicable warranty period. TO THE EXTENT PERMITTED BY LAW, THIS WARRANTY IS IN LIEU
OF ALL OTHER EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. BOSCH DOES NOT ASSUME ANY
RESPONSIBILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES.
TO OBTAIN WARRANTY SERVICE, CONTACT THE NEAREST BOSCH AUTHORIZED SERVICE CENTER OR CALL
1-800-944-2904, OR WRITE TO: BSH HOME APPLIANCES CORP., 5551 MC FADDEN AVENUE
HUNTINGTON BEACH, CA 92649. BE SURE TO PROVIDE YOUR CLOTHES DRYER’S MODEL, SERIAL NUMBER,
PURCHASE DATE AND THE SELLER’S NAME AND ADDRESS.

Installation Instruction
Introduction
Read these installation instructions completely and
carefully. They will save you time and effort and help
to ensure optimum dryer performance. Be sure to
observe all listed warnings and cautions.
These installation instructions are intended for use by
qualified installers. In addition to these instructions the
dryer must be installed:
In the United States, in accordance with the National
Electric Code, ANSI/NFPA70 – latest edition/State
and Municipal codes and/or local codes.
In Canada, in accordance with the Canadian Electric
Code C22.1 – latest edition/Provincial and Municipal
codes and/or local codes.
Tools Needed for Installation
The following tools are needed for installation of this
dryer:
Box cutter
Flat blade screwdriver
#2 Phillips head screwdriver
Duct tape
Caulking gun and compound
Level
Safety goggles
Gloves
Parts Supplied for Installation
Condensation water drain hose (WTL 5410 only)
Stacking kit
Parts Needed for Installation
(Model WTA 3510 only!)
Four inch (approx. 100 mm) diameter metal exhaust
duct (rigid or flexible) of proper length and with elbows
and exhaust vent hood required to vent to outdoors.
Dryer Electrical Cord
The Bosch dryer comes with a 4-wire power supply cord
pre-installed. This cord fits a 4-wire receptacle as shown
in the upper section of Figure 11.
If your receptacle is a 3-wire receptacle, as shown in the
lower section of Figure 11, a 3-wire ‘Dryer Cord’’ must
be purchased locally. The 4-wire cord must then be
removed and the 3-wire cord installed in its place, as
instructed in following section.
When purchasing a 3-wire power supply cord make sure
the cord meets following requirements:
U.L listed in the USA, CSA listed in Canada
240 volt rated (minimum)
30 ampere
Type SRD or SRDT
Five feet long (minimum)
4-wire receptacle
(14-30R)
Dryer shipped with cord to fit
this type 4-wire receptacle.
3-wire receptacle
(10-30R)
If you have 3-wire receptacle,
like this, a 3-wire dryer cord
must be purchased locally.
Figure 11.
 
This appliance must be grounded. In the event of
malfunction or breakdown, grounding will reduce the risk
of electric shock by providing a path of least resistance
for the electric current. This appliance is equipped with
a cord having an equipment grounding conductor and
a grounding plug. The plug must be plugged into an
appropriate outlet that is properly installed and grounded
in accordance with all local codes and ordinances.

Improper connection of the equipment grounding
conductor can result in a risk of electric shock. Check
with a qualified electrician or serviceman if you are in
doubt as to whether the dryer is properly grounded.

  
Some local codes may require a separate ground. In
such cases, the required accessory ground wire, clamp
and screw must be purchased separately.
Never ground the dryer to plastic plumbing lines,
gas lines or water pipes.
 
The receptacle for the dryer cord must be located so that
the power supply cord will be accessible when the dryer
is in the installed position.

The WTA 3510, electric vented dryer, is intended to be
vented to the outdoors. To prevent build-up of moisture
and accumulation of lint indoors, as well as to maintain
maximum drying efficiency, it is recommended that the
Bosch WTA 3510 be vented to the outdoors.

Four-inch (approx. 100 mm) diameter ducting should be
used. Use either rigid metal or flexible metal ducting
material. DO NOT use non-metal duct with this dryer.
Exhaust ducts should be as straight as possible.
Exhaust ducting longer than recommended can extend
drying time, can collect lint and may effect dryer
performance. Joints should be secured with duct tape.
DO NOT use screws to secure joints as lint can collect
on the screws. See Step 4, Exhaust Duct, in following
section titled INSTALLATION for recommended routing
and duct length calculations.
  
The exhaust duct must end with an approved exhaust
vent hood with swing out damper(s). DO NOT use an
exhaust vent hood with magnetic latches. To avoid
restriction of exhaust the outlet must be a minimum of
12 inches (30 cm) above ground level, or any other
obstructing surface. See Figure 17.
 
The WTL 5410, electric condensation dryer, dries by
condensing the moisture from the dryer air and then
pumping this condensate out of the dryer.
The WTL 5410 must have its condensate hose
connected to a suitable drain. See Step 5, Condensate
Hose Connection, in the following section titled
INSTALLATION.
 
A stacking kit is supplied with each dryer in order to
stack Bosch dryer upon a Bosch washing machine.
This part is only necessary if stacking the units is
desired.
     
As an additional accessory for purchase, Bosch offers
a stacking kit for a Bosch washer and dryer that
incorporates a pull-out-tray. The tray offers an area for
folding and easier unloading of the dryer. See your local
dealer for availability and price.

Technical Data
WTA 3510: 88 lbs. (40 kg) – with packaging 199 lbs. (45 kg)
WTL 5410: 99 lbs. (45 kg) – with packaging 110 lbs. (50 kg)
22
1
/
4
’’
(565 mm)
23
5
/
8
’’
(600 mm)
33
1
/
2
’ (850 mm)
adjusts to
34
1
/
2
’ (876 mm)
Figure 12.
 
The Bosch dryers should be CONNECTED TO AN 30A
INDIVIDUAL BRANCH CIRCUIT. North American
models have the following electrical rating:
Model
Volts Hertz Amperes Watts
(max.)
WTA
3510
208/240 60 13 3,100
WTL
5410
208/240 60 13 3,100
Check the rating plate on the dryer to make sure your
machine has this rating.
  
The dryer should not be installed:
in an area exposed to dripping water or outside
weather conditions
in an area where it (and in the case of the WTA 3510,
its exhaust duct) will come in contact with
combustible materials, such as curtains, drapes
or paper.
in areas where water may freeze
in an area where gasoline or other flammables are
kept or stored.
Check local codes before choosing a location. Some
codes do not permit installation of a clothes dryer in
a garage, closet, mobile home or sleeping area. Your
local building inspector should be able to advise you of
the codes in your area.
  
Alcove or Under
Counter
Closet
Sides 0’’ (00 mm) 0’’ (000 mm)
Top 0’’ (00 mm) 10’’ (250 mm)
Rear 1’’ (25 mm) 5’’ (125 mm)
 
Alcove or
Under
Counter
Closet
WTA
3510
Ensure air flow
of
112 cu.ft./min
(3,2 cu.m./min)
through dryer
Closet door must have
2 (louvered) openings,
each having a minimum
area of 60 sq. inches
(387 sq. cm.), located
3 inches (8 cm) from
bottom and top of door. *
WTL
5410
Ensure air flow
of
118 cu.ft./min
(3,3 cu.m./min)
through dryer
Closet door must remain
open during dryer
operation.
* A louvered door with equivalent air opening
is acceptable.

The dryer should be installed on a level, solidly
constructed floor. DO NOT install the dryer on
a carpeted floor.

23
1
/
4
’’
(590 mm)
23
5
/
8
’’
(600 mm)
minimum
33
1
/
2
’’
(850 mm)
minimum
Figure 13.
 
The Bosch dryer can be built-in: that is, you can install
the Bosch dryer under-counter in a kitchen cabinet
opening. The cabinet opening should be square and
have the dimensions as shown in Figure 13.
Note: If installed under a countertop, the countertop
must be continuous and securely attached to
neighboring cabinets.

DO NOT install the dryer in an area where gasoline
or other flammable materials are kept or stored.
The dryer must be installed in a room that is adequately
ventilated. Make sure there is an adequate supply of
fresh air. Both the WTA 3510, electric vented dryer, and
the WTL 5410, electric condensation dryer need an
adequate supply of fresh air for optimum performance.

DO NOT install the dryer in a closet with a solid door.
The dryer must have make up air as specified on
page 17 under Ventilation Requirements.

INSTALLATION
Step 1
Unpack the Dryer
Carefully remove the packing material from the outside
of the dryer.
Step 2
Inspect the Dryer
Thoroughly inspect the dryer, prior to installation, for
possible freight or cosmetic damage.
Step 3
Position Dryer near Installation Area
Move the dryer so that it is within four feet of the desired
position.
Note: Corrugated packing material may be used to
protect the floor. Do not use corrugated material
with staples.
Step 4
Exhaust Duct
(Model WTA 3510 only!)
The WTA 3510 must be exhausted to the outdoors.

1. To reduce the risk of fire, this dryer MUST BE
EXHAUSTED OUTDOORS.
2. DO NOT use non-metal duct with this dryer.
3. DO NOT use duct smaller than 4 inches in diameter.
4. DO NOT use exhaust hoods with magnetic latches.
5. DO NOT exhaust the dryer into a chimney, furnace
cold air duct, attic, crawl space, or any other
ductwork used for venting.
6. DO NOT install flexible duct in an enclosed wall,
ceiling or floor.
7. DO NOT crush or kink the duct.
8. Do clean and inspect the exhaust system on
a regular basis; once a year, at a minimum.
9. The exhaust duct must end with swing out
damper(s).
Be sure to install the exhaust according to all governing
codes and ordinances. Rigid metal duct is recommended
for venting this dryer. If flexible metal duct is used, be
sure it is fully supported when the dryer is in its final
position. Excess ducting should be trimmed off to avoid
sagging or kinking of the ductwork.
The duct may be connected to the left, right or back of
the WTA 3510, electric vented dryer. If connecting to the
left or right hand side of the dryer, remove the sealing
cover from the side to be used, as shown in Figure 14.
Figure 14.
The sealing cover should then be placed over the open
vent opening at the back of the dryer, as shown in
Figure 15.
Figure 15.

The connecting piece supplied with your WTA 3510
dryer must then be inserted in the vent opening that will
be used. See Figure 16.
Figure 16.
  
The ducting system of the dryer, for optimum
performance, should be as short as possible with
a minimum number of elbows. Your WTA 3510 electric
vented dryer will work best when the venting system has
as few restrictions to the flow of air as possible.
Whether installing to an existing venting system or a new
venting system, make sure that all ducting is clean and
free of lint and does not exceed the length per elbows as
shown in Table 1, below:
Maximum length of duct
Number
of Elbows
Rigid Duct Flexible Duct
0
1
2
3
30 ft. (914 cm)
22 ft. (670 cm)
14 ft. (427 cm)
6 ft. (183 cm)
20 ft. (610 cm)
15 ft. (457 cm)
9 ft. (274 cm)
4 ft. (122 cm)
Table 1.
Every elbow must have a minimum diameter of 4 inches
(10 cm).
The above table assumes the use of an approved
exhaust vent hood with a swing out damper. DO NOT
use an exhaust vent hood with magnetic latches.
To avoid restriction of exhaust the outlet must be
a minimum of 12 inches (30 cm) above ground level, or
any other obstructing surface, as shown below, in
Figure 17.
12” (30 cm) min.
Figure 17.
Step 5
Condensate Hose Connection
(Model WTL 5410 only!)
The WTL 5410 must have its condensate drain line
installed and run to a suitable drain. The connection
for the condensate hose is located on the back of the
WTL 5410, see Figure 18.
Figure 18.
Connect the condensate drain hose to the dryer.
The other end should then be placed and secured at
a nearby sink or drain, or if installed with a washer it
may, room permitting, be installed next to the washer
drain hose and drained to the same drain used by the
washer.
Be sure to follow all local codes and regulations in
running the condensate to a suitable drain.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24

Bosch Axxis WTA3510UC User manual

Category
Tumble dryers
Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI