Pneumatic Arm Dual Monitor Desk Mount
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v002k
SKU: STAND-V002K
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST
2
PACKAGE CONTENTS
A (x2)
Arm
B (x1)
Clamp
C (x1)
Clamp Cover
D (x2)
VESA Plate
E (x1)
Pole
F (x1)
Cable Clip
G (x2)
Thumbscrew
H (x3)
Bolt
K (x1)
4mm Allen Key
L (x1)
6mm Allen Key
I (x1)
Support Plate
J (x1)
Base
M-A (x8)
M4x12
M-B (x8)
M4x16
M-C (x8)
M5x12
M-D (x8)
M5x16
M-E (x8)
D5 Washer
M-F (x8)
Spacer
NOTE: SOME HARDWARE MAY NOT BE USED
WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
3
ASSEMBLY STEPS
STEP 1
TOOLS NEEDED
Phillips
Screwdriver
OPTION A: Clamp Installation
Adjust clamp (B) height according to thickness of desktop. Attach clamp cover (C) to clamp (B).
Secure pole (E) to clamp (B) using three bolts (H). Tighten using 4mm Allen key (K).
35-80mm
10-45mm
C
B
K
H
E
2.2-17.6lbs
(1-8kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
PER ARM
4
STEP 1 (Continued)
OPTION B: Grommet Base Installation
For grommet hole attachment, disassemble clamp (B) using 6mm Allen key (L) and a Phillips
screwdriver. Attach base (J) to pole (E) through ⅜” (10mm) grommet hole in desktop. Secure using
bolt from clamp (B) and plate (I).
STEP 2
Slide cable management clip (F) over top of pole (E). Adjust bolt on monitor arm (A) to slide over top
of pole (E) as shown in diagram.
I
0
- 4
0
m
m
J
F
A
L
5
STEP 3
Adjust arm (A) to desired height. Tighten using 6mm Allen key (L).
STEP 4
Attach VESA plate (D) to the back on monitor using bolts (M-A, M-B, M-C, M-D) and washers (M-E).
For curved monitors, spacer (M-F) may be required.
M- E
M- A
M- C
M- E
M- B
M- D
M- F
D
L
6
STEP 5
STEP 6
Slide VESA plate (D) over bracket on arm (A). Secure using thumb screw (G). Remove bottom covers
from arm (A).
Run cables through bottom of arm (A). Re-attach covers.
G
7
STEP 7
Adjust tension in arm and angle of monitor using 6mm Allen key (L). Clockwise reduces tension,
counterclockwise increases tension. The tension should be just enough to hold your monitor in place
without liing itself up.
LAST UPDATED: 07/03/2020
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303
/