Yard Force SA500ECO Quick start guide

Brand: Yard Force

Model: SA500ECO

Category: Lawnmowers

Type: Quick start guide

Yard Force SA500ECO is a robotic lawnmower designed to keep your lawn looking its best with minimal effort. It features adjustable cutting height, allowing you to achieve your desired grass length. The robot efficiently navigates slopes up to 27 degrees and automatically returns to its charging station when the battery is low or when it has completed mowing. The boundary wire guides the robot to mow specific areas while preventing it from leaving the designated boundaries.

Yard Force SA500ECO is a robotic lawnmower designed to keep your lawn looking its best with minimal effort. It features adjustable cutting height, allowing you to achieve your desired grass length. The robot efficiently navigates slopes up to 27 degrees and automatically returns to its charging station when the battery is low or when it has completed mowing. The boundary wire guides the robot to mow specific areas while preventing it from leaving the designated boundaries.

> 1 m

> 2 m

Quick start of Robot mower

1

2

Place the charging station

Make sure that the garden ground is even and

free of obstacles such as stones, branches.

Remove them if there is.

Select S1 or S2 with the

signal button. It is to

prevent disturbance

with your neighbor

who runs a same robot.

On your mowing robot,

the same setting must

be selected both on the

robot itself and charging

station (S1 or S2).

3

5

Programming the mowing robot

4

Begin with the

maximum cutting

height and gradually

reduce it to the

desired cut height.

Main switch

On/Off switch

Cutting height adjust

100 m

2

10 Ω

A

C

Set the boundary wire

with pegs.

E

J

A

I

A

B

A

Close the cover

C

D

For a lawn area less than

100 m

2

or the boundary total

length is less than 40m.

You need a 10 Ω/20 W

cement resistor in boundary.

A

Stripping pliers

10 - 15 mm

G

Possible position of the

charging station

End point of the

boundary wire

1 meter of wire reserved for

possible adjustments

Start point of

the boundary

wire

D

The pegs and the boundary wire

should be as close as possible to

the ground to prevent tripping.

F

H

In front of the loading station, a

straight wire length of 2 m is required.

Beside the charging station

there should be 1m wide

Flat area.

B

To unlock, press 4 times

this “lock” button

Please press “Start”

Select the mowing hours that the

robot should work

®

OK

NO

The boundary wire must never cross.

> 2m

> 10 cm

> 10 cm

< 5 mm

< 27°

> 40 cm

Boundary wire

< 8m

>2m

> 10 m

40 cm

80 cm

S1 S2

> 0.5 m

Buffer zone

If you prefer mowing robot to

travel over the two parallel

boundary wires, the gap distance

of wires above showed must be

less than 5 mm. If the mowing

robot only runs in a circle in

the home mode, please put

a post or obstacle at position A.

If the mowing robot is not to cross the

boundary wire, the distance between

the two wires must be at least 10 cm.

-

Please note the installation

DVD in the box.

> 10 m

Setting of boundary wire

®

1
2

Yard Force SA500ECO Quick start guide

Brand: Yard Force

Model: SA500ECO

Category: Lawnmowers

Type: Quick start guide

Yard Force SA500ECO is a robotic lawnmower designed to keep your lawn looking its best with minimal effort. It features adjustable cutting height, allowing you to achieve your desired grass length. The robot efficiently navigates slopes up to 27 degrees and automatically returns to its charging station when the battery is low or when it has completed mowing. The boundary wire guides the robot to mow specific areas while preventing it from leaving the designated boundaries.

Related papers

Other documents