2 / 12
Table of Contents
Table of Contents and Warnings ............................ 2
Part List ............................................... 3
Assembly and Installation
Adjust upper and lower poles .............................. 4
Attaching to the base assembly ............................ 5
Install steel cross rods .................................... 6
Height adjustment ....................................... 6
Media shelf assembly .................................... 7
Assemble at panel mount ................................ 8-9
Install mount to the frame ................................. 10
Install camera mount ..................................... 11
Cable and wire installation ................................ 11
VESA mounting patterns .................................. 12
WARNING!
Severe personal injury and property damage can result from improper installation. Read
instructions carefully before beginning.
• If you do not understand the instructions or have any concerns please contact a
qualied local installer.
• Do not install or assemble if the product or hardware is damaged or missing, if you
require replacement parts contact your local dealer.
• This product ts most 40˝- 60˝ at panel displays; maximum weight for the display
is 100 lbs. / 45.5kg.
• Do not use this product for anything other than what it was originally designed.
• This product contains moving parts, please use caution.
• The manufacturer disclaims any liability for the modications, improper installation
and installation exceeding maximum weight capacity. The manufacturer will not be
liable for any damages arising out of the use of, or inability to use the product.
Tools Required
-Phillips Screwdriver
-Wrench
3 / 12
Part List
A1 x1
R1 x1
R2 x1 R3 x1
S1 x1
S2 x1
A2 x4
A3 x4
A4 x1
C1 x1
C1 x1 C2 x2
C2 x2 C3 x4
C3 x2
C4 x4C5 x4
B2 x2
B1 x1
B2 x2
B1 x1
B3 x2 B5 x2
B5 x2*
B4 x4
TYPE4
TYPE4
TYPE1, TYPE2, TYPE3
TYPE1, TYPE2, TYPE3
only: TYPE1,
TYPE2, TYPE3
only: TYPE2,
TYPE3, TYPE4
only: TYPE2,
TYPE3, TYPE4
(B3 is pre-
installed)
*1 is pre-installed
only: TYPE3
only: TYPE3
only: TYPE3
E x4 F x4G x4
D x2
H x4 J x4
K x4 L x1 M x1T x8N x2 P x2
M8x25mm
M8x20mm M6x10mmM5x10mm
M6x25mm M5x25mm
4 / 12
1
1
3
2
Adjust upper and lower poles
Locate the spring plungers inside the bottom grommet hole of pole
B1 (If your unit has B5 cross bar pre-installed remove prior). Starting
with the right side pole B2, push the spring plunger down and pull
B2 up slightly and twist it slightly so that the spring plunger remains
offset. This will make adjusting the pole easier. (gure 1)
Repeat the same steps for the left side pole B2 but use your
right foot for stability instead. Align poles B2 and lock the spring
plunger into place. (gure 3)
Remove B5
before step 1.
Only for TYPE1, TYPE2, TYPE3
Hold the poles B1 & B2 with your hands and use your left foot on
the cross bridge of B1 for stability. Pull B2 upward until you reach
your desired height. Twist B2 so that the spring plunger locks into
the nearest spring plunger hole. (gure 2)
B1
B1
B1
B2
B5
B2
B2 B2
Spring
plunger
Spring
plunger
B3 is
pre-installed
gure 1 gure 2 gure 3
Lift pole assembly so that the part remains upright and the
cable management holes are facing toward you.
5 / 12
2
1
2
3
2
1
3
Attaching to the base assembly
Thread casters A2 and washer A3 into the bottom of base A1. Make
sure all casters are locked to prevent movement during installation.
With allen wrench M attach lower poles B1 to base A1 with screw K.
First through the bottom of base A1, then through the top of base A.
After screws K are rmly fastened, push down the screw cover A4
until it locks into place.
Lock Casters
before assembly
K
K
A1
B1
M
1
A3 A3
A2
A2 A2
A2
A4
B1
A1
A3
A3
2
Tighten Fully
with wrench
cable management
holes facing back
6 / 12
3
4
Install steel cross rods
Height adjustment
12
3
Remove the pre-installed
screws on rod B5. Making
sure the upper poles B2
are aligned, slide rods B5
into the top openings.
Slide the upper poles B2 up or down
to the different spring plunger holes for
your desired height. Install grommet
covers B4 into the grommet holes.
Press and hold both spring
plungers to slide the upper
poles B2.
Refasten rods B5
with screws.
Phillips
screwdriver
B5
B5
B5
B5
B2
B4
B4
B4
B4
461⁄2˝ - 621⁄2˝ H / 1050mm - 1500mm
Assistance
Required
Cables
Unplugged
7 / 12
1
1
2
2
Remove the pre-installed screws
on bracket R2. Align bracket R2
to desired position and clamp R2
then retighten the long screws.
Using the short screws fasten
bracket R2 to support R3.
With allen wrench L and the
short allen screws fasten
shelf R1 to support R3.
Phillips
screwdriver
Phillips
screwdriver
B1
R2
R2
R3
R3
R1
5
1
2
3
Media shelf assembly (TYPE2, TYPE3, TYPE4)
Before assembly make sure
there is enough clearance for
the at panel display
L
8 / 12
6a
1
3
2
Assemble at panel mount (TYPE4)
First unscrew and remove
the vertical supports C2 from
mount C1.
Align the screw threads C3 to
the desired vertical support
position of C2. Screw support
C2 into C1 and C3. Insert
support stoppers C4 followed
by caps C5.
Carefully attach mount to
display using screws G,H or J.
Through washer E, support C2
and spacer F.
1. C3
C1
2. C2
C2
C2 C2
C1
C2
3. C4
4. C5
F
F
G
G
H,J H,J
EE
F
F
FE
G, H, J
For a selection of mounting
positions refer to page 12
Plastic spacers must
be used to avoid any
damage from screws
VESA: 200x400 - 400x400mm
VESA: 400x600 - 500x800mm
Phillips
screwdriver
Phillips
screwdriver
Display
not included
Safety Precautions
M8x25mm (G) M5x25mm (H)
M6x25mm (J)
Top of Display
9 / 12
6b Assemble at panel mount (TYPE1, TYPE2, TYPE3)
Adjusting the mount (TYPE4) - After Step 7
C1
C1
F
TT
F
H,J H,J
EE
F
F
E
E
H, J
H, J
VESA: 200x200mm VESA: 200x200 - 600x400mm
Phillips
screwdriver
Phillips
screwdriver
Phillips
screwdriver
Swivel
90°
Safety Precautions
M5x25mm (H)
M6x25mm (J)
Remove pre-installed screws Re-attach screws
10 / 12
7Install mount to frame
Make sure casters
are locked prior to
installation
Attach hooks on C1
onto cross rods B5
Secure lock hook fully
Lock not included
Lift up lock hook
before installing
mount
Heavy Lifting:
Assistance
Required
C1
1
3 4
2
C1
B5
11 / 12
8
9
Install camera mount (TYPE3)
Cable and wire Installation
Please use care when
inserting the wires and
cables into the grommet
to avoid damage
For indoor use only.
Avoid excessive wind,
heat & humidity.
Adjustable height
N
P
Phillips
screwdriver
S1
S2
/
