VADDIO 999-9952-100 Owner's manual

Complete Manual for the

OneLINK HDMI

Camera Extension

Document 411-0019-30 Rev. C

November 2019

ii

Contents

Overview 1

What's in this Guide 2

Features 2

Unpacking the OneLINK HDMI Camera Extension 3

OneLINK HDMI for HDBaseT Cameras 3

OneLINK HDMI For HDBaseT Cameras Used with Codecs 3

OneLINK HDMI for HDMI Cameras 4

OneLINK HDMI for HDMI Cameras Used with Codecs 5

A Quick Look at the OneLINK Device 7

Front Panel of the Receiver 7

Connector Panel of the Receiver 7

Connector Panel of the EZCamera Interface Module (EZIM) 8

Installing the OneLINK Device 9

Don’t Void Your Warranty! 9

Cabling Notes 9

RS-232 Connector Pin-Outs 10

IR Forwarding Connector Pin-Out 10

Mounting the OneLINK Device 11

About Installations Using the Half-Recessed Ceiling Mount 11

Visual Conventions for Connection Diagrams 11

Connections for HDBaseT Cameras 11

Kits and Systems for HDBaseT Cameras 12

Connecting a Vaddio HDBaseT Camera 12

Connections for HDBaseT Cameras Used with Codecs 13

Kits for HDBaseT Cameras Used with Codecs 13

Connecting a Vaddio HDBaseT Camera and Polycom Codec 14

Connecting a Vaddio HDBaseT Camera and Cisco Codec 17

Connections for HDMI Cameras 20

Kits for HDMI Cameras 20

Connecting a RoboSHOT HDMI Camera 21

Connecting a Polycom EagleEye IV Camera 22

Connecting a Cisco Camera 23

Connecting a Sony or Panasonic HDMI Camera 25

Connections for HDMI Cameras Used with Codecs 27

Kits for HDMI Cameras Used with Codecs 27

Connecting a RoboSHOT HDMI Camera and Polycom Codec 28

Connecting a Polycom EagleEye IV Camera and Polycom Codec 31

Connecting a RoboSHOT HDMI Camera and Cisco Codec 34

Connecting a Cisco Camera and Codec 38

Powering Up the Equipment 43

Configuring the Camera 43

Configuration and Administration Tasks 44

Compatible Web Browsers 44

Accessing the Web Interface 45

Web Interface Cheat Sheet 46

Configuring Network Settings 47

Assigning a Hostname 48

Specifying Time Zone and NTP Server 48

Managing Access and Passwords 49

Disabling Telnet Access 49

Enabling or Requiring HTTPS 49

Adding Room Information to the Web Interface 50

Viewing System Information 51

Saving (Exporting) or Restoring (Importing)a Configuration 51

Rebooting the OneLINK Device 52

Restoring Factory Settings 53

Starting a Firmware Update 54

Contacting Vaddio Technical Support and Viewing Diagnostics 55

Telnet Serial Command API 56

link power 57

network settings get 57

network ping 58

system reboot 58

system factory-reset 59

sleep 59

version 60

history 60

help 60

exit 61

Specifications 62

Troubleshooting 63

Operation, Storage, and Care 64

Compliance Statements and Declarations of Conformity 65

FCC Part 15 Compliance 65

ICES-003 Compliance 65

European Compliance 66

Warranty Information 67

Index 68

iii

Integrator's Complete Guide to the OneLINK HDMI Camera Extension

1

Overview

This guide covers the OneLINK™ HDMI camera extension, which is available in the following kit

configurations for use with Vaddio or third-party cameras, with or without third-party codecs.

n999-1105-043/143/943, OneLINK HDMI for Vaddio HDBaseT™ cameras

n999-9520-000/001/009, OneLINK HDMI camera extension for Polycom EagleEye IV cameras with

Polycom codecs

n999-9530-000/001/009, OneLINK HDMI camera extension for Sony and Panasonic cameras

n999-9540-000/001/009, OneLINK HDMI camera extension for RoboSHOT HDMI cameras with

Polycom codecs (discontinued)

n999-9545-000/001/009, OneLINK HDMI camera extension for Vaddio HDBaseT cameras with Polycom

codecs

n999-9560-000/001/009, OneLINK HDMI camera extension for Cisco cameras with Cisco codecs

n999-9570-000/001/009, OneLINK HDMI camera extension for RoboSHOT HDMI cameras with Cisco

codecs (camera has been discontinued)

n999-9575-000/001/009, OneLINK HDMI camera extension for Vaddio HDBaseT cameras with Cisco

codecs

n999-9590-000/001, OneLINK HDMI camera extension for RoboSHOT HDMI cameras (camera has

been discontinued)

Part number suffixes indicate power cord set types. Those ending in -000 include cord sets for use in North

America; -001 kits include cord sets for use in Europe and the UK; -009 kits include cord sets for use in

Australia and New Zealand.

The OneLINK HDMI camera extension is also available as a component of several Vaddio camera

systems.

Note

The kits for RoboSHOT HDMI cameras are still available, although the RoboSHOT 12 HDMI and

RoboSHOT 30 HDMI cameras have been discontinued. OneLINK devices are not compatible with

RoboSHOT 12E HDMI and RoboSHOT 30E HDMI cameras.

If the camera extension is sold for use with an HDMI camera, it is shipped with a OneLINK EZCamera

Interface Module (EZIM).

What's in this Guide

This guide provides information about:

nUnpacking

nPhysical features

nInstallation

nConfiguration and system administration

nTelnet API for third-party control

nSpecifications

nTroubleshooting and maintenance

nWarranty

For your convenience, the information you need to install this product is also available in the smaller, stand-

alone Installation Guide for the OneLINK HDMI Camera Extension, which covers unpacking, physical

features, installation, and initial power-on.

Features

nSimple, fast, clutter-free camera installation– power, control, video, and network connectivity over a

single cable

nExtends installation distance for HDMI and HDBaseT™ cameras up to 100 m (328 ft.) using Cat-6

cable; 230 ft (70 m) using Cat-5e

nPasses uncompressed HDMI®video up to 2160p/29.97

nBidirectional control via Ethernet and RS-232

nCompatible with Vaddio HDBaseT cameras – no EZCamera Interface Module (EZIM) needed

nCompatible with legacy RoboSHOT HDMI and other HDMI cameras

nAvailable in system configurations with Vaddio cameras

nKits available for use with Polycom and Cisco codecs and HDMI cameras

Note

OneLINK products are not compatible with RoboSHOT 12E HDMI or RoboSHOT 30E HDMI cameras.

2

Integrator's Complete Guide to the OneLINK HDMI Camera Extension

Unpacking the OneLINK HDMI Camera Extension

Make sure you received all the items you expected. Here are the packing lists for the OneLINK HDMI kits.

Every OneLINK device ships with a power supply and at least one AC cord set. The last three digits of the

kit part number contain the regional code that specifies which cord set(s). For most OneLINK kits, the part

numbers follow this convention:

nKits with part numbers ending in -000 include one AC cord set for North America.

nKits with part numbers ending in -001 include two AC cord sets, one for Europe and one for the UK.

nKits with part numbers ending in -009 include one AC cord set for Australia and New Zealand.

Exceptions are noted case by case in the following packing lists.

OneLINK HDMI for HDBaseT Cameras

OneLINK HDMI Camera Extension for Vaddio HDBaseT Cameras, 999-1105-043/143/943

Camera not included.

nOneLINK HDMI Receiver, 998-1105-043

nPower supply, 48 VDC/1.36 A, with AC cord set(s)

oKit 999-1105-043 includes one AC cord set for North

America.

oKit 999-1105-143 includes two AC cord sets, one for

Europe and one for the UK.

oKit 999-1105-943 includes one AC cord set for Australia and New Zealand.

nEZCamera RS-232 control adapter (998-1001-232)

nQuick-Start Guide 411-0019-01

OneLINK HDMI For HDBaseT Cameras Used with Codecs

OneLINK HDMI for Vaddio HDBaseT Cameras with Polycom Codecs, 999-9545-000/001/009

Camera and codec not included.

nOneLINK HDMI Receiver

nPower supply, 48 VDC/1.36 A, with AC cord set(s)

n3-position Euro-style connector, 5 mm

nFan-out cable, codec side, 2 ft. (0.6 m)

nEZCamera RS-232 control adapter 998-1001-232

nQuick-Start Guide 411-0019-01

3

Integrator's Complete Guide to the OneLINK HDMI Camera Extension

OneLINK HDMI for Vaddio HDBaseT Cameras with Cisco Codecs, 999-9575-000/001/009

Camera and codec not included.

Note

If connecting to a Cisco SX20 codec, you will need to provide

a Cisco split cable, Cisco part number CAB-PHD4XS2-

SPLIT.

nOneLINK HDMI Receiver

nPower supply, 48 VDC/1.36 A, with AC cord set(s)

nHDMI cable, 3 ft. (0.9 m)

nCustom-pinout Cat-5e cable for Cisco, 3 ft. (0.9 m)

nEZCamera RS-232 control adapter 998-1002-232

nCat-5e patch cable, 3 ft. (0.9 m)

nQuick-Start Guide 411-0019-01

OneLINK HDMI for HDMI Cameras

OneLINK HDMI for RoboSHOT HDMI Cameras, 999-9590-000/001/009

Camera not included.

nOneLINK HDMI Receiver

nOneLINK EZCamera Interface Module (EZIM) with

mounting screws

nPower supply, 48 VDC/1.36 A, with AC cord set(s)

nPower cable EIAJ-04 to EIAJ-04, 1 ft. (0.3 m)

nCat-5e patch cable, 1 ft. (0.3 m), qty. 2

nHDMI cable, 1 ft. (0.3 m)

nEZCamera RS-232 control adapter

nQuick-Start Guide 411-0019-02

Note

The RoboSHOT 12 HDMI and RoboSHOT 30 HDMI cameras have been discontinued. This kit is not

compatible with RoboSHOT 12E HDMI and RoboSHOT 30E HDMI cameras.

OneLINK HDMI for Sony and Panasonic Cameras, 999-9530-000/001/009

Camera not included.

nOneLINK HDMI Receiver

nOneLINK EZCamera Interface Module (EZIM)

nPower supply, 48 VDC/1.36 A, with AC cord set(s)

nPower cable EIAJ-04 to EIAJ-04, 1 ft. (0.3 m)

nPower cable EIAJ-04 to 3x6.3mm, 1 ft (0.3 m)

nWall mount with mounting hardware for Sony and

Panasonic cameras

nHDMI cable, 1 ft. (0.3 m)

nRJ-45 to 8-pin mini-DIN cable, 1 ft. (0.3 m)

nCat-5e patch cable, 1 ft. (0.3 m)

nQuick-Start Guide 411-0019-02

4

Integrator's Complete Guide to the OneLINK HDMI Camera Extension

OneLINK HDMI for HDMI Cameras Used with Codecs

OneLINK HDMI for Polycom Cameras with Polycom Codecs, 999-9520-000/001/009

Camera and codec not included.

nOneLINK HDMI Receiver

nOneLINK EZCamera Interface Module (EZIM)

nPower supply, 48 VDC/1.36 A, with AC cord set(s)

nWall mount with mounting hardware for Polycom codec

and camera

nFan-out cable, EZIM side, 1 ft. (0.3 m)

nFan-out cable, codec side, 2 ft. (0.6 m)

n3-position Euro-style connector, 5 mm

nEZCamera RS-232 control adapter 998-1001-232

nQuick-Start Guide

OneLINK HDMI for RoboSHOT HDMI with Polycom

Codecs, 999-9540-000/001/009

Camera and codec not included.

nOneLINK HDMI Receiver

nOneLINK EZCamera Interface Module (EZIM), with

mounting screws

nPower supply, 48 VDC/1.36 A, with AC cord set(s)

nFan-out cable, codec side, 2 ft. (0.6 m)

n3-position Euro-style connector, 5 mm

nHDMI cable, 1 ft. (0.3 m)

nPower cable EIAJ-04 to EIAJ-04, 1 ft. (0.3 m)

nCat-5e patch cable, 1 ft. (0.3 m), qty. 2

nQuick-Start Guide 411-0019-02

Note

The RoboSHOT 12 HDMI and RoboSHOT 30 HDMI cameras have been discontinued. This kit is not

compatible with RoboSHOT 12E HDMI and RoboSHOT 30E HDMI cameras.

5

Integrator's Complete Guide to the OneLINK HDMI Camera Extension

OneLINK HDMI for Cisco Cameras with Cisco Codecs, 999-9560-000/001/009

Camera and codec not included.

Note

If connecting to a Cisco SX20 codec, you will need to provide

a Cisco split cable, Cisco part number CAB-PHD4XS2-

SPLIT. This cable is also required when connecting to a Cisco

Precision 40 or Precision HD 1080p2.5x camera; you will need

two of them if connecting one of these cameras and an SX20

codec.

nOneLINK HDMI Receiver

nOneLINK EZCamera Interface Module (EZIM)

nPower supply, 48 VDC/1.36 A, with AC cord set(s)

nPower cable EIAJ-04 to 5.5x2.1 mm, 1 ft. (0.3 m)

nWall mount with mounting hardware for Cisco codec and

camera

nHDMI cable, 3. ft. (0.9 m)

nHDMI cable, 1 ft. (0.3 m)

nCustom-pinout Cat-5e cable for Cisco, 3 ft. (0.9 m)

nCustom-pinout Cat-5e cable for Cisco, 1 ft. (0.3 m)

nCat-5e patch cable, 1 ft. (0.3 m)

nCat-5e patch cable, 3 ft. (0.9 m)

nEZCamera RS-232 control adapter 998-1002-232

nQuick-Start Guide 411-0019-02

OneLINK HDMI for RoboSHOT HDMI with Cisco Codecs, 999-9570-000

Camera and codec not included.

Note

If connecting to a Cisco SX20 codec, you will need to provide

a Cisco split cable, Cisco part number CAB-PHD4XS2-

SPLIT.

nOneLINK HDMI Receiver

nOneLINK EZCamera Interface Module (EZIM) with

mounting screws

nPower supply, 48 VDC/1.36 A, with AC cord set(s)

nPower cable EIAJ-04 to EIAJ-04, 1 ft. (0.3 m)

nHDMI cable, 3 ft. (0.9 m)

nHDMI cable, 1 ft. (0.3 m)

nCustom-pinout Cat-5e cable for Cisco, 3 ft. (0.9 m)

nCat-5e patch cable, 1 ft. (0.3 m), qty. 2

nCat-5e patch cable, 3 ft. (0.9 m)

nEZCamera RS-232 control adapter 998-1002-232

nQuick-Start Guide 411-0019-02

Note

The RoboSHOT 12 HDMI and RoboSHOT 30 HDMI cameras have been discontinued. This kit is not

compatible with RoboSHOT 12E HDMI and RoboSHOT 30E HDMI cameras.

6

Integrator's Complete Guide to the OneLINK HDMI Camera Extension

A Quick Look at the OneLINK Device

This section covers the physical features of the OneLINK HDMI camera extension.

All OneLINK kits include a receiver, which is typically co-located with other equipment, up to 328 ft (100 m)

away from the camera. OneLINK kits for use with HDMI cameras also include an EZCamera Interface

Module (EZIM) HDBaseT converter, which is mounted adjacent to the camera.

Front Panel of the Receiver

nData Display – Shows the IP and MAC addresses for the OneLINK HDMI camera extension (not the

camera). Use the IP address to access the OneLINK HDMI web interface.

nPower System Reset button (illuminated red) – reboots the OneLINK Bridge without affecting the

connected camera.

Connector Panel of the Receiver

From the left:

nPower input jack – Use the supplied 48VDC, 1.36A power supply.

nOneLINK interface port – Connect a Cat-5e (or better) cable to the EZIM, or to the camera if your

OneLINK kit or system did not include an EZIM.This bidirectional connection carries video, network

connectivity including H.264 IP streaming from the camera (if available), RS-232 control, and 12 VDC

power.

nHDMI output – HDMI output to a connected display.

nRS-232 port – Connect to a camera controller.

nIR forwarding port – To forward IR signals from the camera, if available.Modulated and non-

modulated outputs provided.

nNetwork port – H.264 IP streaming (if available from the camera), web interface access, and third-

party IP control via Telnet API.

7

Integrator's Complete Guide to the OneLINK HDMI Camera Extension

Connector Panel of the EZCamera Interface Module (EZIM)

If the OneLINK device is used with an HDMI camera, the EZIM is required.

From the left:

nPower output jack – Supplies power to the camera. The kit you purchased includes the appropriate

cable to connect your camera's power input to this jack.

nNetwork port – Provides network connectivity to the camera for H.264 IP streaming (if available from

the camera), web interface access, and third-party control via Telnet API. Connect to the camera's

network port.

nRS-232 port – Provides RS-232 connectivity to the camera, for third-party control. The kit you

purchased may include a cable and/or an RS-232 adapter to connect to the camera's RS-232 port.

nHDMI input – Receives HDMI video from the camera. Connect to the camera's HDMI output.

nOneLINK port – Single-cable connection to the OneLINK receiver. This bidirectional connection

carries all video, power, and control.

8

Integrator's Complete Guide to the OneLINK HDMI Camera Extension

Installing the OneLINK Device

This section covers:

nThings to know before you start the installation

nBasic connection examples

Download dimensional drawings, quick-start guides, and other information from the appropriate OneLINK

kit page on legrandav.com.

Don’t Void Your Warranty!

Caution

Use only the power supply included with this product. Using a different one will void the warranty, and

could create unsafe operating conditions or damage the product.

Do not connect the OneLINK power supply to a Vaddio camera. It does not provide the correct voltage for

Vaddio cameras, and will damage the camera and void the camera's warranty.

This product is for indoor use only. Do not install it outdoors or in a humid environment. Do not allow it to

come into contact with any liquid. Do not install or operate this product if it has been dropped, damaged, or

exposed to liquids. If any of these things happen, return it to Vaddio for safety and functional testing.

Note

Disassembling this product will void the warranty.

Cabling Notes

Cable distance between the EZIM (or the camera, if no EZIM is used)and the OneLINK device is a

maximum of 328 feet (100 m) using Cat-6 or Cat-7 cable, or 230 feet (70 m) using Cat-5e cable.

Cat-6 or Cat-7 cabling allows longer maximum cabling distance, and may provide better performance in

noisier RF or EMF environments. We recommend shielded cabling if the cables will be coiled, run tightly

with other cables, or routed near sources of electromagnetic interference such as power lines or fluorescent

light fixtures. When in doubt, use shielded Cat-6 cable.

Caution

When making cables for Vaddio products, do not use pass-through RJ-45 connectors. If

they are crimped incorrectly, they can damage the connectors on the product, cause

intermittent connections, and degrade signal quality. Physical damage to the connectors

will void your warranty.

Intact

Contact fingers will make reliable

contact with the cable connector

Damaged

Some contact fingers are bent and

will NOT make reliable contact

with the cable connector

We recommend using high-quality connectors and a high-quality crimping tool.

Pro Tip

To prevent tragic mishaps, label both ends of every cable.

9

Integrator's Complete Guide to the OneLINK HDMI Camera Extension

RS-232 Connector Pin-Outs

OneLINK Receiver - RS-232 Control Port

1. Unused

2. Unused

3. Unused

4. Unused

5. Unused

6. GND – green

7. RX (from TX of controller) – brown/white

8. TX (to RX of controller) – brown

OneLINK EZIM - RS-232 Control Port

1. Unused

2. Unused

3. Unused

4. IR GND

5. IR (non-mod)

6. GND – green

7. TX (to RX of camera) – brown/white

8. RX (from TX of camera) – brown

Note

Vaddio recommends adhering to the 568B cabling standard for Cat-5 cabling.

IR Forwarding Connector Pin-Out

1. Modulated IR

2. Common Ground

3. Non-modulated IR

10

Integrator's Complete Guide to the OneLINK HDMI Camera Extension

Mounting the OneLINK Device

If you are installing the OneLINK device with a OneLINK EZIM, mount the EZIM with or near the camera.

The Thin Profile Wall Mount for the camera may include mounting holes to attach the EZIM to the underside

of the mount using two 6-32 screws. Connect all required cables during camera installation.

Rack and under-table mounting kits are available for the receiver. Follow the mounting instructions supplied

with the kit.

About Installations Using the Half-Recessed Ceiling Mount

If the connected camera is mounted in Vaddio's Half-Recessed Ceiling Mount, the camera's IR receiver is

unable to receive signals from the remote. The mount has an IR receiver that can forward commands to the

camera; this must be powered separately using Power Extension Module 999-1005-021. Cameras powered

by OneLINK devices cannot supply power to the mount's IR receiver.

Visual Conventions for Connection Diagrams

The following sections provide representative connection diagrams for the various OneLINK kit and system

configurations available. All diagrams in this guide use these visual conventions for connection type.

Connections for HDBaseT Cameras

In this configuration, the OneLINK HDMI extends network connectivity, power, and control to an HDBaseT

camera, and brings HDMI video from the camera to a display. The camera can optionally be controlled by a

camera controller on an RS-232 serial connection to the OneLINK HDMI or over the network, depending on

the controller.

If an IP stream is available from the camera, the OneLINK device passes it to the network. IP streaming

resolutions up to 2160p/30 are supported. HDMI output resolution and streaming parameters (including

resolution) are configured on the camera, not the OneLINK device.

The controller is optional.

11

Integrator's Complete Guide to the OneLINK HDMI Camera Extension

Kits and Systems for HDBaseT Cameras

This block diagram applies to:

nOneLINK HDMI for HDBaseT Cameras, 999-1105-043/143/943 – compatible with all Vaddio HDBaseT

cameras.

nRoboSHOT 12 HDBT OneLINK HDMI System, 999-9960-100/101

nRoboSHOT 30 HDBT OneLINK HDMI System, 999-9963-100/100W/101/101W

nRoboSHOT 20 UHD OneLINK HDMI System, 999-9950-100/101/109

nDocCAM 20 HDBT OneLINK HDMI System, 999-9968-200/201/209

nFuture systems consisting of a Vaddio HDBaseT camera and a OneLINK HDMI receiver

Connecting a Vaddio HDBaseT Camera

999-1105-043/143/943

This diagram is also valid for the following systems:

nRoboSHOT 12 HDBT OneLINK HDMI System, 999-9960-100/101

nRoboSHOT 30 HDBT OneLINK HDMI System, 999-9963-100/100W/101/101W

nDocCAM 20 HDBT OneLINK HDMI System, 999-9968-200/201/209

In this diagram, the OneLINK HDMI extends network connectivity, power, and control to a

RoboSHOTHDBT camera, and brings camera video to the connected HDMI display. The OneLINK HDMI

passes the camera's IP stream (if available) to the network.

Items in this diagram:

nOneLINK HDMI receiver

nRoboSHOT12 HDBT camera (not included in kit 999-1105-043/143/943)

nHDMI display and HDMI cable (not included)

nLaptop receiving the camera's IP stream (not included)

nCat-5e cables for OneLINK and network connections (not included)

RoboSHOT HDBT Camera

Other Vaddio HDBaseT cameras connect in the same way.

12

Integrator's Complete Guide to the OneLINK HDMI Camera Extension

Connections for HDBaseT Cameras Used with Codecs

In this configuration, the OneLINK HDMI extends network connectivity, power, and control to an HDBaseT

camera, and brings HDMI video from the camera to the codec. The codec may be connected to the

OneLINK device directly via RS-232, or they may communicate over the IPnetwork, depending on the

codec.

If an IP stream is available from the camera, the OneLINK device passes it to the network. IP streaming

resolutions up to 2160p/30 are supported. HDMI output resolution and streaming parameters (including

resolution) are configured on the camera, not the OneLINK device.

Kits for HDBaseT Cameras Used with Codecs

This block diagram applies to:

nOneLINK HDMI for Vaddio HDBaseT Cameras with Polycom Codecs, 999-9545-000/001/009 –

compatible with all Vaddio HDBT cameras and with Polycom RealPresence Group Series codecs.

nOneLINK HDMI for Vaddio HDBaseT Cameras with Cisco Codecs, 999-9575-000/001/009 –

compatible with all Vaddio HDBT cameras and with Cisco C20, C40, C60, SX20, and SX80 codecs.

13

Integrator's Complete Guide to the OneLINK HDMI Camera Extension

Connecting a Vaddio HDBaseT Camera and Polycom Codec

999-9545-000/001/009

In these diagrams, the OneLINK device extends network connectivity, power, and control to a RoboSHOT

HDBT camera, and connects it to a Polycom RealPresence Group Series codec. The OneLINKdevice

passes the camera's IP stream (if available) to the network. The codec provides HDMI video to the

connected display.

Other Vaddio HDBaseT cameras would be connected in exactly the same way.

Items in these diagrams:

nOneLINK HDMI receiver

nPower supply with ACcord set

nCodec-side fan-out cable, bare wires terminated with 3-position, 5mm Euro-style connector

nRoboSHOT 12 HDBTcamera (not included)

nPolycom RealPresence Group Series codec (not included)

nHDMI display and HDMI cable (not included)

nLaptop receiving the camera's IP stream (not included)

nCat-5e cables for OneLINK and network connections (not included)

RoboSHOTHDBT Camera and Polycom RealPresence Group 310 Codec

The Group 500 codec looks very similar and connects in the same way.

Other Vaddio HDBaseT cameras connect in the same way.

14

Integrator's Complete Guide to the OneLINK HDMI Camera Extension

RoboSHOTHDBT Camera and Polycom RealPresence Group 700 Codec

Other Vaddio HDBaseT cameras connect in the same way.

15

Integrator's Complete Guide to the OneLINK HDMI Camera Extension

Hardware Note: IR Forwarding

Use the supplied 3-position Euro-style connector to terminate the two unterminated wires of the codec-side

fan-out cable as follows:

nBlack wire: Center position (pin 2)

nRed wire: Right position (pin 3)

Connect this part of the fan-out cable to the IR FORWARD connector on the OneLINK HDMI receiver.

Note

Some fan-out cables have a black/white wire instead of a red one. Wiring is the same – black to pin 2,

black/white to pin 3.

Some older fan-out cables have the wires reversed. This will not damage the equipment. If IR forwarding

does not work when you terminate the cable per these instructions, remove power from the OneLINK

device, disconnect the fan-out cable, and re-terminate the wires with red (or black/white) to pin 2 and black

to pin 3. Then reconnect the cable and power up the OneLINK device again.

Hardware Note: Connection and Configuration Changes

After connecting or configuring the equipment, reboot the OneLINK device, camera, and codec. Note that

rebooting the OneLINK device does not affect the camera and codec; they must be rebooted separately.

16

Integrator's Complete Guide to the OneLINK HDMI Camera Extension

Connecting a Vaddio HDBaseT Camera and Cisco Codec

999-9575-000/001/009

In these diagrams, the OneLINK device extends network connectivity, power, and control to a RoboSHOT

12 HDBT camera, and connects it to a Cisco codec. The OneLINKdevice passes the camera's IP stream

(if available) to the network. The codec provides HDMI video to the connected display.

Other Vaddio HDBaseT cameras would be connected in exactly the same way.

Items in these diagrams:

nOneLINK HDMI receiver

nPower supply and AC cord set

nRS-232 adapter 998-1002-232 (used with standard Cat-5 cable on C20, C60. and SX80 codecs)

nCisco split cable CAB-PHD4XS2-SPLIT(not included; required for SX20 codec)

nCodec-side null modem cable (used with split cable on SX20 codec)

nRoboSHOT 12 HDBTcamera (not included)

nCisco codec (not included)

nHDMI display and HDMI cable (not included)

nLaptop receiving the camera's IP video stream (not included)

nCat-5e cables for OneLINK and network connections (not included)

RoboSHOTHDBT Camera and Cisco C20 Codec

Other Vaddio HDBaseT cameras connect in the same way.

17

Integrator's Complete Guide to the OneLINK HDMI Camera Extension

Page is loading ...

VADDIO 999-9952-100 Owner's manual

This manual is also suitable for

VADDIO 999-9952-100 Owner's manual

Related papers