PROJECTION:
FSG OF
IDEX CORPORATION
4
1
1
1
9
1
6
1
3
1
7
1
5
2
8
4
8
4
2
2
SEE NOTE 1
E
G
G
G
11
1
13
1
12
1
10
3
SEE NOTE 2
QMAX / QTWO
DSD
NOTES:
REPLACE PLUGS WITH PUSH-ON HOSE FITTINGS AS NEEDED.
1.
INSTRUCTIONS: SET PRESSURE LIMITER BY:
2.
SETUP ON A BENCH STAND WITH SHOP AIR AND
1.
GAUGE.
LOOSEN LOCKNUT AND THEN TURNING CW FULLY.
2.
SET PRESSURE LIMITER BY RUNNING SYSTEM AND
3.
ADJUSTING PRESSURE LIMITER CCW UNTIL THE AIR
PRESSURE DROPS TO DESIRED AIR PRESSURE
SETTING (BETWEEN 95-100 PSI - DO NOT EXCEED
100 PSI).
TIGHTEN LOCKNUT.
4.
REFER TO THE INSTRUCTIONS PROVIDED WITH THE
5.
VALVE FOR ADDITIONAL INFO.
E
G
G
REVISIONS
ECN
REV
CHANGED FROM
BY
DATE
APVD
CFL3399
E
REMOVED POH FITTINGS
JRH
23JAN2015
AJG
5861
F
CORRECTED ELBOW POSITION
MAC
11AUG2022
AJG
6520
GREPLACED 104598 FITTING WITH THE RELIEF VALVE TO LIMIT
PRESSURE GOING TO CLUTCH ASSEMBLY. ADDED NOTE 2.
JS2
10JAN2024
AJG
ITEM
NO.
PART
NUMBER
DESCRIPTION
QTY.
1
010-0710-00-0
STRAINER, 1/4" WYE
1
2
018-0814-02-0
SCREW, HEX, 8-32 X 1-1/2, ZINC
2
3
019-00096
BRACKET, MANIFOLD, AIR, SMARTCAFS
1
4
082-0253-02-0
NIPPLE, HEX, 1/4" NPT
1
5
110-0800-02-0
NUT, HEX, 8-32, ZINC
2
6
178-1050-00-0
MANIFOLD, AIR, SMARTCAFS
1
7
217-0201-04-0
PLUG, 1/4 NPT HEX HEAD BRASS
1
8 102523
WASHER, FLAT, #8, 300 SST
4
9 104592
ADPT 1/4" MNPT X 3/8" POH
1
10
217-0101-13-0
PLUG, PIPE 1/8 NPT SH BRASS
3
11 120064
REDUCER BSHG 1/8 MPT X 1/4 FPT
1
12
038-00109-000
RELIEF VALVE, 1/4", 225 PSI
1
13 104591
ADAPTER 1/4 MPT x 1/4 POH
1
C
D
1
2
3
A
B
1
2
3
C
4
5
6
A
B
COPYRIGHT ©
NOT TO BE REPRODUCED OR USED TO
MAKE OTHER DRAWINGS OR MACHINERY
FINISH
MADE FROM
MATERIAL
UNLESS OTHERWISE SPECIFIED
DIMENSIONS ARE IN MILLIMETERS
[ INCHES ARE FOR REFERENCE, ONLY]
TOLERANCE FOR MILLIMETER DIMENSIONS:
X: ±1
X.X: ±0.5
X.XX: ±0.25
X.XXX: ±0.125
ANGLES: ±0.25°
SURFACE TEXTURE IN μm Ra
REMOVE ALL SHARP EDGES, 0.25MAX
TITLE
PROJECT
RDW
JRP
01NOV2012
DATE
APPROVED
DRAWN
B
SIZE
1 OF 1
DRAWING NUMBER
178-1050-10-0
SCALE
1:2
G
SHEET
REV
D
6
5
4
MANIFOLD, AIR,
SMARTCAFS, ASSEMBLY
7
8
7
8
E
F
E
F
/
