WaterWorks GUDV3P Installation guide

WaterWorks
Brand
WaterWorks
Model
GUDV3P
Category
Sanitary ware
Type
Installation guide
PRODUCT SUPPORT | 800.927.2120 | WATERWORKS.COM PAGE 1 OF 3 | UPDATED ON 5.19.2022
STYLE No. GUDV3P, GU3PDV
ViaWorks Three Way Diverter Valve for
Pressure Balance Shower Systems
INSTALLATION GUIDELINES
STYLE NO. GUDV3P, GU3PDV†
IMPORTANT:
¾ALL VALVES AND TRIMS SOLD SEPARATELY.
¾To ensure this DIVERTER VALVE is installed properly, you must read
and follow these guidelines.
¾The owner/user of this DIVERTER VALVE must keep this information
for future reference.
¾This DIVERTER VALVE must be paired with a PRESSURE BALANCE
VALVE (sold separately).
¾This VALVE CANNOT be used with a DIVERTING TUB SPOUT.
¾CAUTION: The VALVE rough-in depth is measured from the center of
the inlets to the surface of the finished wall and VARIES depending
on the TRIM used.
¾This DIVERETER VALVE and associated TRIM (SOLD SEPARATELY)
must be installed by a professional licensed contractor and must
be onsite prior to rough-in. This allows the installer to visualize the
installation.
¾This DIVERTER VALVE is sold partially assembled but shown fully
disassembled for illustrative and service purposes only. Inspect
the VALVE to ensure you have all the parts required for proper
installation.
¾Be sure your installation conforms to all federal, state, and local
codes. In the State of Massachusetts, all installations must comply
with the rules and regulations set forth within 248 CMR.
¾If further assistance is required, please contact Product Support at 1-800-927-2120 Monday
through Friday, 8am – 6pm EST.
¾Refer to the separate Service Parts Documents for available replacement parts.
TECHNICAL DETAILS:
DETAIL SPECIFICATION
INLET/OUTLET CONNECTIONS 1/2” MALE NPT †
FITTINGS HOLE DIAMETER Ø2” [51mm]
ROUGH-IN DEPTH VARIES ‡
UNRESTRICTED MAX FLOW RATE @ 45 PSI [3 bar] 10gpm [38L/min]
WATER PRESSURE MAXIMUM 85psi [6.0 bar]
WATER PRESSURE MINIMUM 20psi [1.5 bar]
WATER PRESSURE RECOMMENDED 45psi [3.0 bar]
† Style No. GU3PDV is provided with 4 BSPP ADAPTERS. ADAPTERS are packaged separately
and assembly is required. Replacement ADAPTERS can be ordered separately:
●Universal 1/2” NPT Female x 1/2” Male BSPP Adapter
Style No. UNUK03
‡ Refer to the Installation Guidelines of the specific DIVERTER VALVE TRIM being used for the
MAXIMUM and MINIMUM rough-in depth dimensions.
PRODUCT SUPPORT | 800.927.2120 | WATERWORKS.COM PAGE 2 OF 3 | UPDATED ON 5.19.2022
STYLE No. GUDV3P, GU3PDV
ViaWorks Three Way Diverter Valve for
Pressure Balance Shower Systems
INSTALLATION GUIDELINES
VALVE FUNCTION AND HANDLE OPERATION:
¾CAUTION: When this DIVERTER VALVE is paired
with a DIVERTER VALVE TRIM that has specific
device MARKINGS, it is crucial that the outlet ports
are correctly plumbed to those specific devices (i.e.
handshower and shower head)
¾The required PRESSURE BALANCE VALVE (sold
separately) controls on/off and mixes hot and cold
water. Mixed water flows out at a fixed volume to the
DIVERTER VALVE which has 3 positions, each 120°
apart.
●3 that can direct water to a MAXIMUM of 3
devices. Water CANNOT flow out of the devices
simultaneously (i.e. out of the shower head AND
handshower together).
●The DIVERTER VALVE incorporates tactile
feedback at each position.
[GUDV3P SHOWN] [HANDLE OPERATION]
56G:46
@FT=6E
4
56G:46
@FT=6E
3
DEVICE
OUTLET
"A"
>:I65
H2E6C
:?=6E
ROUGH-IN AND VALVE PREPARATION:
¾Check incoming water pressure.
¾IMPORTANT:
●The VALVE rough-in depth is measured from the
center of the inlet to the surface of the finished
wall and varies depending on the TRIM used.
●Refer to the Installation Guidelines of the
specific DIVERTER VALVE TRIM being used for
the MAXIMUM and MINIMUM rough-in depth
dimensions.
¾CAUTION:
●DO NOT APPLY DIRECT HEAT TO THE VALVE.
Pre-solder any connections to prevent damage to
the CARTRIDGE and other internal components.
●The DIVERTER VALVE TRIM components (i.e.
HANDLE and TRIM PLATE) may be packaged
separately from each other.
DIM VALUE
AVARIES ‡
B Ø2” [51mm]
DIVERTER
VALVE
THREADED
TUBE
FINISHED
WALL
TILE GUARD
[IN/OUT
MARKINGS] CENTER
OF
INLET
"A"
ROUGH-IN
DEPTH
"B"
FITTINGS
HOLE
‡ Refer to the Installation Guidelines of the
specific DIVERTER VALVE TRIM being used
for the MAXIMUM and MINIMUM rough-in
depth dimensions.
"A"
"B" "C"
PRODUCT SUPPORT | 800.927.2120 | WATERWORKS.COM PAGE 3 OF 3 | UPDATED ON 5.19.2022
STYLE No. GUDV3P, GU3PDV
ViaWorks Three Way Diverter Valve for
Pressure Balance Shower Systems
INSTALLATION GUIDELINES
FINISHED
WALL
DIVERTER
VALVE
MOUNTING
TABS
[BLOCKING
RECOMMENDED]
ROUGH-IN
DEPTH
CENTER
OF INLET
1. The DIVERTER VALVE rough-in depth is measured
from the center of the inlet to the surface of the
finished wall and varies depending on the TRIM
being used.
2. From the PRESSURE BALANCE VALVE (sold
separately) being used, run a copper supply line to
the proper height of the DIVERTER VALVE making
sure it’s positioned according to the IN/OUT
MARKINGS so that mixed water flows into the inlet
and all piping and fittings are secured.
3. Run 1/2” copper supply lines from the outlet ports
to the 3 desired devices making sure all piping and
fittings are secured.
4. Turn on the water supply and operate the
CARTRIDGE STEM to flush out the supply lines,
verify all VALVE positions are functioning properly,
and check for leaks. Ensure the supply lines have
been fully flushed then turn off the water.
5. Install the TILE GUARD to protect the DIVERTER
VALVE during the completion of the finished wall
and to create the exact opening required to ensure
access to the CARTRIDGE for future servicing.
TILE GUARD
FINISHED
WALL
DIVERTER
VALVE
[1/2"
MALE NPT
THREADS] *
1/2"
COPPER
SUPPLY
[IN/OUT
MARKINGS]
* Style No. GU3PDV is provided with 4 BSPP ADAPTERS.
[1/2"
MALE NPT
THREADS] *
1/2"
COPPER
SUPPLY
* Style No. GU3PDV is provided with 4 BSPP ADAPTERS.
1/2"
COPPER
SUPPLY
1/2"
COPPER
SUPPLY
CARTRIDGE
STEM
"B"
"C"
"A"
[360°]
* TURN ON WATER AND CHECK FOR LEAKS!
  • Page 1 1
  • Page 2 2
  • Page 3 3

WaterWorks GUDV3P Installation guide

WaterWorks
Brand
WaterWorks
Model
GUDV3P
Category
Sanitary ware
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents