Finn T30D MS Owner's manual

LBT30-CE

T30 Diesel HydroSeeder

®

CE-Compliant

Parts and Operator’s Manual

Model MS Serial No.

9281 LeSaint Drive • Fairfield, Ohio 45014

Phone (513) 874-2818 • Fax (513) 874-2914

Activate

Your Warranty

By Registering

TODAY!!!

II

NOTES

II

ACTIVATE YOUR FINN EQUIPMENT WARRANTY

IMPORTANT INFORMATION ON ACTIVATING

YOUR FINN EQUIPMENT WARRANTY!!!

IT IS IMPERATIVE THAT YOU, THE PURCHASER, COMPLETE THE FOLLOWING STEP IN ORDER TO

ACTIVATE THE FINN CORPORATION LIMITED WARRANTY.

COMPLETE THE “EQUIPMENT REGISTRATION” FORM ON

THE NEXT PAGE AND MAIL TO THE FINN CORPORATION.

IF FINN CORPORATION DOES NOT HAVE YOUR COMPLETED REGISTRATION

FORM ON FILE, YOUR WARRANTY CLAIM WILL BE DENIED.

Once your Finn equipment has been registered, your Finn Limited Warranty will

be activated per the warranty statement on the other side of this notice.

<<What should you do if you need repairs or parts under Warranty?>>

1. NOTIFY FINN CORPORATION OF THE FAILURE OF MATERIAL OR WORKMANSHIP

1-800-543-7166 Extension (246)

WARRANTY@FINNCORP.COM

2. AFTER YOU OR YOUR SERVICE DEALER NOTIFY FINN, FINN WILL:

VERIFY THAT WE HAVE YOUR “REGISTRATION” ON FILE

VERIFY THAT THE WARRANTY PERIOD IS IN EFFECT

VERIFY THAT THE RELATED PART(s) ARE INCLUDED IN THE SCOPE OF

WARRANTY (PENDING FINN’S INSPECTION OF DEFECTIVE PARTS)

SEND YOU REPLACEMENT PART(S) AND A “WARRANTY INFORMATION PACKET"

REQUEST YOU FOLLOW ALL INSTRUCTIONS AS NOTED IN THE “PACKET”

 

 

 

 (Within 2 weeks)

 

 



Finn Corporation Commercial Limited Warranty

Effective February 20, 2006

OUR WARRANTY TO YOU:

Finn Corporation warrants to you, the original purchaser, for use (or

rental to others for use) all new construction machinery, parts and

attachments (except those referred to herein) that are manufactured

by Finn to be free from defects in material and workmanship for a

period of 12 months from date of purchase or 1200 hours of use,

whichever comes first.

Replacement parts provided under the terms of this warranty are

warranted for the remainder of the warranty period applicable to

the product to which parts are installed, as if parts were original

components of the product.

WHAT FINN WILL DO:

Upon notification of Finn concerning a failure of material or

workmanship in accordance with the above stated Warranty, Finn

Corporation will:

• Verify claim falls within the valid warranty time frame.

• Verify the product and equipment has been registered with Finn

in order to be eligible for warranty coverage.

• Upon affirmation of warranty period and registration, Finn will

send to you a new or repaired replacement part(s), whichever

Finn elects and a “Warranty Claim Information packet” contain-

ing instructions for processing the warranty claim.

• Evaluate the part when defective part is returned. Note: Failure

to return defective part within two weeks will result in an invoice

being sent to the customer. In addition, if damage to a part is

determined not to be covered under the warranty, the customer

will be billed for the replacement part.

• Reconcile costs with customer for parts and shipping, as deter-

mined by our inspection of failed parts, and confirmation of war-

ranty coverage, per the terms of this warranty.

• Correction of nonconformities, in the manner provided above,

shall constitute fulfillment of all liabilities of Finn Corporation

under this warranty.

WHAT YOU MUST DO TO OBTAIN WARRANTY SERVICE:

• As the purchaser covered under the above limited warranty

you must REGISTER the equipment with Finn as such owner.

Should registration not be on file with Finn Corporation, your

warranty will be void. (See Operators manual for Registration

Form)

• Notify Finn Corporation of any failure of material or workman-

ship as described under this warranty.

Web notification: W[email protected]

Phone 1-800-543-7166 extension 246

• Complete the required steps in the “Warranty Claim Information

packet” (which Finn will send you upon notice of your notifica-

tion) and return the defective part(s) as directed in the packet to

Finn Corporation.

WHAT THE WARRANTY DOES NOT COVER:

1. Allied equipment or trade accessories not manufactured by it,

such as but not limited to ignitions, starters, tires, batteries,

hose, magnetos, carburetors, engines, labor, or like or unlike

equipment or accessories including discharge hoses. (Such

being subject to the warranty, if any, provided by their respec-

tive manufacture’s).

2. Secondhand, used, altered, or rebuilt machines or parts.

3. Defects, malfunctions or failures resulting from accidents,

abuse, misuse, improper servicing, or lack of performance of

required operational guidelines and maintenance service, as

outlined in the Finn Corporation’s Operators Manual(s).

4. The warranty shall be null and void to the extent any defect or

failure of the products warranted arises out of or is caused by

accessories or component parts not manufactured or supplied

by Finn Corporation, whether same are supplied by purchaser,

dealers, or any other party.

THIS IS THE ONLY EXPRESS WARRANTY ON OUR PRODUCTS:

We neither assume nor authorize anyone to assume for us any other

express warranty. The Distributor/Dealer has no authority to make

any representation or promise on behalf of Finn Corporation or to

modify the terms or limitations of this warranty in any way.

THIS WARRANTY THEREFORE SHALL BE IN LIEU OF ALL

OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING,

BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF

MERCHANTABILITY OR FITNESS FOR A PARTICULAR

PURPOSE.

LIMITATIONS ON OUR RESPONSIBILITY WITH RESPECT TO

PRODUCTS PURCHASED:

THE REMEDIES OF THE USER SET FORTH HEREIN ARE

EXCLUSIVE, WITHOUT REGARD TO WHETHER ANY

DEFECT WAS DISCOVERABLE OR LATENT AT THE TIME

OF DELIVERY OF THE PRODUCT TO THE PURCHASER.

The essential purpose of this exclusive remedy shall be to pro-

vide the original purchaser with repair or replacement of parts

that prove to be defective within the period and under the condi-

tions previously set forth. This exclusive remedy shall not have

failed of its essential purpose (as that term is used in the Uniform

Commercial Code) provided Finn remains willing to repair or

replace defective parts within a commercially reasonable time

after it obtains actual knowledge of the existence of a particular

defect.

IN NO EVENT SHALL FINN BE LIABLE FOR ANY SPECIAL,

CONSEQUENTIAL, INCIDENTAL OR INDIRECT DAMAGES,

INCLUDING LOST PROFITS OR LOST COMMERCIAL

OPPORTUNITIES, WITH RESPECT TO THE SALE OF

THE ABOVE WARRANTED PRODUCT OR ANYTHING

DONE IN CONNECTION THEREWITH, OR FOR PROPERTY

DAMAGE SUSTAINED BY A PERSON CLAIMING TO BE A

THIRD PARTY BENEFICIARY OF A SURVIVING WARRANTY

UNDER THE LAW OF ANY JURISDICTION.

NOTICE:

FINN CORPORATION URGES THE USE OF ONLY FINN

CORPORATION SUPPLIED PARTS AND ATTACHMENTS

TO ASSURE PROPER PERFORMANCE AND SAFE

OPERATION OF FINN CORPORATION EQUIPMENT. INSIST

ON PARTS AND ATTACHMENTS MANUFACTURED

OR SUPPLIED BY FINN CORPORATION WHEN YOU

PURCHASE, REPAIR OR REPLACE YOUR FINN

EQUIPMENT AND ATTACHMENTS. BECAUSE FINN

CORPORATION CANNOT ASSURE THAT PARTS AND

ATTACHMENTS NOT MANUFACTURED OR SUPPLIED BY

FINN MEET FINN CORPORATION’S QUALITY STANDARDS,

SPECIFICATIONS, OR OPERATING REQUIREMENTS,

OUR WARRANTY IS NOT EFFECTIVE TO THE EXTENT

ANY FAILURE OF OR DEFECT IN A FINN CORPORATION

PRODUCT ARISES FROM OR IS CAUSED BY PARTS,

ATTACHMENTS OR COMPONENTS NOT ORIGINATING

WITH FINN CORPORATION. USE OF FINN CORPORATION

EQUIPMENT WITH PARTS AND ATTACHMENTS NOT

MANUFACTURED OR SUPPLIED BY FINN COULD RESULT

IN PERSONAL INJURY.

Effective February 20, 2006

INDEX

Safety First . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Attachments................................................2

Valve Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Starting Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Material Capacities. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5

Tank Capacity Chart. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Discharge Nozzle Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Hydraulic System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Lubrication Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Pump Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Finn Model T30-CE Technical Specifications. . . . . . . . . . . . . . . . . . . . . . 10

Notes ..................................................11-12

Parts Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-33

Notes..................................................14

Pictorial Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Suction, Discharge, And Recirculation . . . . . . . . . . . . . . . . . . . . . 16-17

Clump Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18-19

Hose Reel Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-21

Hydraulic System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22-23

Hydraulic Pump Drive Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Hydraulic Agitator Drive Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Agitator and Bearing Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . 26-27

Common Loose Parts & Engine . . . . . . . . . . . . . . . . . . . . . . . . . . 28-29

Control Panel Wiring. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Tool Kit & Seal Repair Kits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Decals.............................................. 32-33

Hydroseeder® is a registered trademark of the Finn Corporation

VI

NOTES

VI

1

SAFETY FIRST

With any piece of equipment, new or used, the most

important part of its operation is SAFETY!

Finn Corporation encourages you and your employees to

familiarize yourselves with your new equipment and to

stress safe operation.

The first six pages of this manual are a summary of all the

main safety aspects associated with this unit. Be sure to

read completely before operation of machine.

This symbol is used throughout the operation

and maintenance sections of this manual to

call attention to safety procedures.

- Pay Attention -

DANGER: Immediate hazards which WILL result in severe personal injury

or death.

WARNING: Hazards or unsafe practices which COULD result in severe per-

sonal injury or death.

CAUTION: Hazards or unsafe practices which COULD result in minor per-

sonal injury or product or property damage.

IMPORTANT: Indicates that equipment or property damage could result if instruc-

tions are not followed.

NOTE: Gives helpful information.

Finn Corporation

CALIFORNIA

Proposition 65 Warning

The engine exhaust and some of its

constituents are known to the State

of California to cause cancer, birth

defects, and other reproductive harm.

CALIFORNIA

Proposition 65 Warning

Battery posts, terminals and related

accessories contain lead and lead

compounds, chemicals known to the

State of California to cause cancer

and reproductive harm. Wash hands

after handling.

2

OPERATION & MAINTENANCE MANUAL

FOR THE CE-COMPLIANT

FINN T30 HYDROSEEDER®

ATTACHMENTS (OPTIONAL):

1. Discharge hoses: Discharge hoses are available in 50 ft. (15 m) and 100 ft. (30 m) lengths up to a

total of 150 ft. (45 m). Hose of a greater length may adversely affect the discharge distance, and the

discharge time of the HydroSeeder®. All connections are camlock quick operating fittings, includ-

ing the connection to the end of the discharge piping. A nozzle is connected to the end of the hose

next to the remote discharge valve. Once the hose is connected, the HydroSeeder® is ready to oper-

ate. Flow through the hose and the nozzle is controlled by the remote discharge valve. When using

this valve, the recirculation valve on the HydroSeeder® MUST BE OPEN to allow flow at times

when the remote valve is closed. See Figure 2 on page 9.

          

  



2. Hose Reel: The live hose reel mounts on top of the unit. The 150 foot (45 m) capacity electric

rewind reel will wind up and store empty hose. It is wired to the unit's battery.

3. Air Gap Fill Pipe: A bolt on the air gap fill pipe is available that mounts directly to the raised hatch

liner and swings into position when the hatch lid is open.

3

VALVE OPERATION:

The base HydroSeeder® is equipped with three (3) independently operated ball valves to control slurry flow

(see Fig. 2). The first valve is the recirculation valve. An open recirculation valve allows flow back into the

tank. The second valve is the pump discharge valve. An open pump discharge valve allows slurry to flow

through the discharge hose. The third valve, located at the end of the discharge hose is the remote valve. An

open remote valve allows discharge of the slurry onto the area being covered.

 -







         



          

        



RECIRCULATION

VALVE

PUMP

DISCHARGE

VALVE

REMOTE

VALVE

OPEN

CLOSED

FIGURE 1

4

STARTING PROCEDURE:

 



Before starting, open the recirculation valve, close discharge valve, disengage (turn off) the clutch, and

place the agitator control in the neutral position.

1. Set throttle about 1/4 open.

2. Pull Choke control out.

3. Turn the key clockwise until the starter catches and engine fires.

4. Push the Choke control in for even running.

NOTE: This engine has a safety system which will shut the engine off if

the engine temperature goes above or if the oil pressure decreases

below an acceptable level.

AREA COVERAGE - MATERIAL CAPACITY:

To determine the coverage per load for any HydroSeeder®, three questions must be answered prior to the

application. First, is the job to be done “one step” (which is when the seed, fertilizer and mulch are applied

proportionally per load) or “two step” (which is when the seed and fertilizer are applied alone and then cov-

ered by mulch as a second operation)? Second, at what rates (usually in pounds (kg) per 1,000 square feet

(92.9 square meters), or pounds (kg) per acre) are the seeding materials to be applied? Finally, what are the

loading capacities of the HydroSeeder®?

Application rates vary for different geographic locations, but in general, seed is applied at 6-10 pounds

(2.72-4.54 kg) per 1,000 square feet (92.9 square meters); fertilizer is applied at a rate of approximately

400 pounds (181.44 kg) per acre; and fiber mulch is applied at 1500 to 2000 pounds (680.39 to 907.18 kg)

per acre. (Note: There are 43,560 square feet (4,046.86 square meters) in an acre). Local agronomists,

agricultural extension agents, or soil and water conservation officials should be contacted for more specific

information on application rates for a given area.

The following tables show loading versus coverage rates for the Finn T30. Table A shows rates for “one

step” applications. The coverage area is determined by the fiber mulch capacity of the HydroSeeder®, and

the rate at which it is applied. Table B shows the area coverage when seeding only, where little or no mulch

is applied. The coverage area is determined by the granular solids capacity of the HydroSeeder®, and the

rate at which the solids are applied.

5

TABLE A



   

Seed Fertilizer  Sq. Ft. (Sq. m.)

T30 28 lbs (13 kg) 32 lbs (15 kg) 120 lbs (54 kg) 3,485 (324)

Above Table is based on 1,500 lbs (680.39 kg) of mulch, 400 lbs (181.44 kg) of

fertilizer and 345 lbs (159.49 kg) of seed (8 lbs (3.63 kg)/1,000 square feet (92.9

square meters)) per acre.



120 lbs (54.43 kg) Mulch per Tank

1,500 lbs (680.39 kg) Mulch per Acre = .08 Acre per Load = 3485 sq. ft. (323.77 m²)

400 Pounds (181.44 kg) Fertilizer per Acre x .08 Acre = 32 Pounds (14.51 kg) Fertilizer per Load

345 Pounds (159.49 kg) Seed per Acre x .08 Acre = 28 Pounds (12.70 kg) Seed per Load

TABLE B



   

Seed Fertilizer Total (sq. ft.(sq. m.)) 

T30 230 lbs (104 kg) 270 lbs (122 kg) 500 lbs (226 kg) 28,750 (8,763) 0.66 (.27)

Above Table is based on rates of 8 lbs (3.63 kg) seed and 9.2 lbs (4.17 kg) fertilizer

per 1,000 square feet (92.9 square meters).



500 lbs (226.40 kg) Tank Capacity (Solids)

8 lbs (3.63 kg) Seed + 9.2 lbs (4.17 kg) Fertilizer per 1,000 sq. ft. (92.9 m²)

= 28,750 sq. ft (2,670.96 m²) per Load

8 lbs (3.63 kg) Seed

1,000 sq. ft. (92.9 m²) x 65,340 sq. ft. (6,070.28 m²) = 522 lbs (236.78 kg) Seed per Tank

6

TANK CAPACITY CHART:

300 (1136) 6.25 (15.9) 32.75 (83.2)

275 (1041) 8.75 (22.2) 30.25 (76.8)

250 (946) 11 (27.9) 28 (71.1)

225 (852) 13.5 (34.3) 25.5 (64.8)

200 (757) 16 (40.6) 23 (58.4)

175 (662) 18.25 (46.4) 20.75 (52.7)

150 (568) 20.5 (52.1) 18.5 (47.)

125 (473) 23 (58.4) 16 (40.6)

100 (379) 25.25 (64.1) 13.75 (34.9)

75 (284) 27.75 (70.5) 11.25 (28.6)

50 (189) 30.75 (78.1) 8.25 (21.)

25 (95) 34 (86.4) 5 (12.7)

in. (cm) from

bottom

T-30

Gallons

(liters)

in. (cm) from

top

FIGURE 2

TOP

BOTTOM

300

150

250

200

100

75

50

25

275

225

175

125

7



Nozzles are stored in the tool box. This HydroSeeder® is equipped with three nozzles - one long distance

and two ribbon fan nozzles. The following chart tabulates the approximate distance, width, and discharge

time of the nozzles when used with the platform option. When using the base unit these factors will vary

according to the type and length of hose being used.

   

Long Distance Up to 70 ft (21m) - 12 min.

Narrow Ribbon Up to 45 ft (14m) 10 ft (3m) 8 min.

Wide Ribbon Up to 35 ft (10m) 20 ft (6m) 8 min.

HYDRAULIC SYSTEM:

The hydraulic system on your Finn HydroSeeder® is designed to give trouble free service, when properly

maintained. The most important areas of maintenance are the hydraulic oil and filtration. The reservoir

holds 6 gallons (22.70 liters) of ISO Grade 46 Hydraulic Oil. The hydraulic oil should be replaced per the

lubrication schedule or if the oil becomes milky or it gives off a burnt odor. The hydraulic oil filter must be

replaced on schedule with a 25 absolute micron filter - Finn part #021618. The hydraulic system relief is

factory set at 2,250 psi.

A

B

FIGURE 4

8

LUBRICATION AND FLUIDS CHART

     

1 Check Grease Level in

Pressure Lubricator SL Daily 1

2 Grease Agitator Shaft Bearings CL Daily 2

3 Check Engine Oil Level MO Daily 1

4 Change Engine Oil and Filter MO See Engine Manual 1

5 Grease Pump Bearings CL Weekly 2

6 Check Hydraulic Fluid Level HO Weekly 1

Change Hydraulic Fluid and Filter HO Seasonally 1

7 Check Fuel Tank FU Daily 1

LUBRICANT OR FLUID USED

SL Seal Lube (Sodium Base)

CL Chassis Lubricant

MO Motor Oil See Engine Manual for Recommendations

HO ISO Grade 46 Hydraulic Oil

FU Diesel

TIME KEY FLUID CAPACITIES

DAILY (8 hours) Diesel - 5.5 Gallons (20.8 L)

Engine Oil - 4 Quarts (3.8 L)

WEEKLY (40 Hours) Hydraulic Fluid - 6 Gallons (23 l)

SEASONALLY (500 hours)

SEE ENGINE MANUAL

FIGURE 3

2

72

1

5

3

4

6

9

PUMP MAINTENANCE:

           -



PUMP ASSEMBLY

      

1B Suction Cover Bolt 4 8B Bearing Bolt 4

1N Suction Cover Nut 4 8LW Bearing Washer 4

1 Suction Cover 1 9 Pump Shaft 1

2 O-Ring 1 10 Snap Ring 1

3 Impeller 1 11 Drive Hub 1

4 Mechanical Seal 1 11B Drive Hub Bolt 2

5 Pump Casing 1 11N Drive Hub Nut 2

5B Suction Cover Bolt 8 12 Clutch Retainer 1

5W Suction Cover Washer 8 12B Locking Bolt 1

6 Radial Lip Seal 1 12W Lock Washer 1

7 Casing Bearing 1 13 Clutch 1

7B Bearing Bolt 4 14 Clutch Spacer 1

7LW Bearing Washer 4 15 Pump Frame 1

8 Frame Bearing 1 16 Casing Drain Plug 1

NOTE: See parts manual for Finn part number

15

5

1

3

9

8

7

13 11

12

14

10

4

6

7LW

7B

5B

5W

1N

1B

12LW

8B

8LW

2

12B

11B

11LN

16

FIGURE 4

10

OPERATING PARAMETERS:

• AIR TEMPERATURE ...................................................+41°F to +104°F (+5°C to +40°C)

• HUMIDITY ..................................................................50% RH @ +104°F (+40°C)

• ALTITUDE ..................................................................Suitable for use @ 3,281´ (1,000 m) above mean sea level

• TRANSPORTATION & STORAGE ..............................-13°F to +131°F (-25°C to +55°C)

TEMPERATURE

POWER ..............................................................................Kohler Diesel 18.2 hp (14 kW), electric start, air-cooled, direct

injection diesel, oil guard protection

ENGINE SAFETY SYSTEM................................................Low oil pressure, high water temperature shutoff

TANK SIZE ........................................................................310 gallon (1,175 liter) liquid capacity

260 gallon (984 liter) working capacity

FUEL TANK CAPACITY ......................................................5.5 gallon (20.8 liter)

PUMP .................................................................................Centrifugal 3¨ x 1-1/2¨ (7.5 cm x 3.75 cm), 65 GPM @ 60 psi

(227 lpm @ 414 kPa), 34¨ (1.9 cm) solid clearance

PUMP DRIVE .....................................................................Direct drive through electric clutch, pump drive is independent of

agitator operation

AGITATION ........................................................................Mechanical paddle agitation and liquid recirculation

AGITATOR DRIVE...............................................................Reversible, variable speed hydraulic motor (0-129 rpm), with

control lever at front and rear of unit

DISCHARGE DISTANCE ...................................................Up to 70´ (23 m) from end of hose

MAX. MATERIAL CAPACITY .............................................500 lbs. (277 kg) granular solids, 100 - 120 lbs. (45 - 55 kg) fiber

mulch

NOZZLES ...........................................................................(1) narrow fan, (1) wide fan & (1) long distance

HOSE ATTACHMENT .........................................................50´ x 1-1/4¨ (15.24 m x 3.18 cm) semi-rigid polybraid or 50´ x 1-1/2¨

(15.24 m x 3.81 cm) collapsible hose, remote valve

EMPTY WEIGHT ...............................................................1,050 lbs. (477 kg)

FINN MODEL T30-CE TECHNICAL SPECIFICATIONS

3´ 11¨

(119 cm)

8´ (244 cm)

4´ 1¨

(117 cm)

4´ 10¨

(119 cm)

HydroSeeder

T30

11

NOTES

11

12

NOTES

12

13

T30 Hydroseeder®

CE-COMPLIANT

Parts Manual

Model MS

14

NOTES

14

Page is loading ...

Finn T30D MS Owner's manual

This manual is also suitable for

Finn T30D MS Owner's manual

Related papers

Other documents