Kmart 42912040 User manual

product

Maximum weight of the user shall NOT exceed 165 lbs/75 kg for this product.

CUSTOMER SERVICE:

PRODUCT WARRANTY

CUSTOMER SERVICE

0.

0

(QFORVXUHV\VWHPVDUHGHVLJQHGWRSUHYHQWXVHUVIDOOLQJRIIWKHWUDPSROLQH'RQRWDOORZXVHUVWRLQWHQWLRQDOO\

ERXQFHWRZDUGRURIIWKHEDUULHUDVWKLVFDQXQEDODQFHWKHWUDPSROLQHDQGFRQWLQXDOLPSDFWPD\GDPDJHWKHHQFORVXUH

)RFXV\RXUH\HVRPWKHHGJHRIWKHWUDPSROLQH7KLVZLOOKHOSFRQWURO\RXUERXQFH

6WRS\RXUERXQFHE\IOH[LQJ\RXUNQHHVDV\RXUIHHWFRPHLQFRQWDFWZLWKWKHWUDPSROLQHEHG

/HDUQWKLVVNLOOEHIRUH\RXDWWHPSWDQ\RWKHUV

$YRLGERXQFLQJWRRKLJK6WD\ORZXQWLOO\RXFDQFRQWURO\RXUERXQFHDQGUHSHDWHGO\ODQGLQWKHFHQWUHRIWKHWUDPSROLQH

'RQRWERXQFHLPPHGLDWHO\DIWHUDPHDO

It is important that children are not involved in the assembly

of the trampoline.

(a) Place the trampoline on a flat level surface with impact attenuating properties such

as grass and ensure that it is sufficiently stable to prevent it from tipping over and/or

blowing away. Sandbags or pegs may be suitable anchorage devices.

f

NO. Diagram Description

Top rail

Bracket without welding

Bracket with welding

Quantity

A 6

3

6

1

48

1

3

B

C

D

E

F

G

H

I

J

K

L

Horizontal Leg

Bend Leg

Mat

Frame Pad

Spring

Enclosure net

Steel top rim

Upper Enclosure pole

Lower Enclosure pole

9

Hexagon wrench M4

Hexagon wrench M5

NO. Diagram Description Quantity

3

6

1

6

M

N

O

P

Q

R

S

T

U

V

Screw for plastic

connector

Plastic

connector

Screw for Leg

Spring tool

Wrench

Enclosure net tie

down strap

Needle for Enclosure net tie

down strap

Leg to Frame

hardware

10

1.Connect the Top rail A)with the Bracket without welding(B together as below picture show,repeat

3 times, pay attaention to the direction

A x3 B x3

A x3 C x3

A

B

2.Connect the Top rail A)with the Bracket with welding(C together as below picture show,

repeat 3 times,pay attaention to the direction

11

3Connect the finished parts of step 1and step 2 together as below pictures show,

pay attention to the direction

4.Connect the Horizonal Leg Dand the Bend Leg Etogether then secure it use the screw

for Leg(O) as below picture picture show

O x6

D x3

E x6

D

E

12

5.Connect the finished parts of step 3 and the finished parts of step 4 together as below picture show

6.Use the Leg to Frame hardware(V)to connect the Bend Leg Eand the Bracket without welding(B),

Bracket with welding(C) as below picture show

V x6

13

7.Turn over the finished parts of Step 6 and connect as below picture one by one.

8.

Warning!

When attaching the springs, do not place your hands,

arms, legs or any other body part close to the connector

points(i.e. joints connecting the steel tubes).The connector

points can become pinch points as the trampoline springs

tighten up. Wear heavy duty working gloves to protect

your hands from pinching by the springs and protective

goggles to avoid injuries to the eyes. Be steady when

installing the springs as it can rebound and fly off if you

inadvertently let go when not hooked properly. Make sure

no children are playing nearby when installing or assisting

in the assembly of the trampoline.

Starting at the point "Zero" hook one end of the spring(H) into the triangle-ring

on the mat(F).Holding the spring tool(P) underhand, pull the other end of the

spring and lock it into the hole on the frame as shown below

After you have secured the spring at point "Zero", place another spring at the

opposite place and then divide into two parts again with another two springs

at three and nine o' clock position.

Attach the springs in the same manner as the previous step.

Then follow 1,2 ,3 process to get spring finished assembly.

The number of triangle-rings sewn onto the mat is equal to the number of holes

on the frame. If you notice that you have miscounted a hole or triangle-ring,

remove and reinstall the springs as necessary while maintaining an even

distribution of tension as explained above.

14

15

H*48pcs

!

Please pay

attention to the end

shape of the spring

connect to the top rail

The curved hook end

!

connected to the

triangle -ring.

The first hole

!

16

9.Put the Lower enclosure pole (L)into the Bracket with welding(C) as below picture show,

please pay attention that the clip must be pulled out

10.Put the Frame Pad(G)on the Mat(F),pay attention that the opening of the pad aligned with the Lower

Enclosure pole(L)

L x3

G x1

17

11.Connect the steel top rim(J) with the Enclosure net(I)top rim tunnel as below picture show

12.Connect the steel top rim (J) with the Plastic connector Nby Screw(M) then put the

Plastic connector(N) into the Upper Enclosure pole(K),please make sure the clip must be pulled out.

I x1

J x3

K x3 M x3 N x3

M

18

13.Connect the finished part of Step 12 and the Lower enclosure pole (L) as below picture show

14.Put up the Pad(G), connect the Enclosure net and the Mat(F) by the needle(T) and the Enclosure net

tie down strap (U) as below picture show

T x1

U x1

19

15.After finishing the Enclosure net assembly,please put down the Pad , tighten the elastic strap on

the pad (G) and the traiangle ring on the Mat(F) together to fasten them.

20

Page is loading ...

Kmart 42912040 User manual

Kmart 42912040 User manual

Related papers

Other documents