Oneida Air Systems AXD000002-HD-55 Owner's manual

Brand: Oneida Air Systems

Model: AXD000002-HD-55

Type: Owner's manual

Doc. #ZBI000025

Appearance may vary slightly

U.S. Patent: #7282074B1,

#6833016B2, #7282074C1

June 12, 2019

CDD-35 and CDD-55

Cyclonic Pre-Separator

#AXD000002-HD-35

1Oneida Air Systems

You will need the following:

• 7/16" Wrench

• Pliers

• PhillipsHeadScrewdriver

• Flat-headScrewdriver

Contents

ID Part number Part description Qty

AAXD200055 2" x 55" Static Conductive Hose 1

B AFC270250 2 1/2" Rubber Coupling 1

C AXD600103 2” Elbow 2

D ACB360000 Turn Key Hose Clamp 2

E VXC110001 Steel Cyclone Separator 1

F AHX000016 Hardware Pack 1

F1 AFS015920 1/4"-20 X 3/4” Bolts 6

F2 AFW025000 1/4" Flat Washer 6

F3 AFT000005 1/4" Flange Nut 6

G AXG000004A Gasket for Cyclone 1

H SEX033555 Steel Lid for 35 & 55 Gallon Drum 1

I RGZ723555 Rubber Gasket Ring 1

J* SES350000

SES550000

35 Gallon Steel Drum with Clamp

55 Gallon Steel Drum with Clamp

If you cannot find an item on the list, examine the packaging materials very carefully.

There may be hardware leftover.



ID Part number Part description Qty

K** RLH000023 23 MM Button Plug 1

L** RLH000031 31 MM Button Plug 1

M SDD000003 Industrial Steel Drum Dolly 1

M1 RHC000011 3" Locking Casters 4

M2 AFB025075 1/4"-20 x 3/4" Carriage Bolts 16

M3 AFT900006 1/4" Nylock Nut 16

Please unpack the parts carefully and conrm

you have received each item listed here.

*There will be leftover components.

***Some components are pre-installed

at the factory and are listed here for your

convenience.

22oneida-air.com

Contents (Continued)

D CA

3Oneida Air Systems

35 Gallon Dimensions

Nominal dimensions shown. Dimensions subject to slight variations in manufacturing.

Inlet and Outlet Diameter: 2"

44"

1117 mm

27"

686 mm

40.5"

1029 mm

to center

of inlet

44oneida-air.com

55 Gallon Dimensions

Nominal dimensions shown. Dimensions subject to slight variations in manufacturing.

Inlet and Outlet Diameter: 2"

54"

1372 mm

51"

1295 mm

to center

of inlet

27"

686 mm

5Oneida Air Systems

AligntheCastersoftheDrumDolly(M)over

thepre-punchedholes.[FIG. 3]

Note: e bolt heads will not interfere with the

drum..

Assembly Instructions

Place Gasket for Cyclone (G) over the center

hole in the Steel Lid (H) and line up the holes.

Secure the Cyclone (E) into the threaded inserts

using the 1/4"-20 X 3/4" Bolts (F1), 1/4" Flat

Washers (F2) from the Hardware Pack (F) as

shown in [FIG. 1]

SlidetheRubberGasketRing(I)ontotherim

oftheDrum(J),pushingdownaroundtheentire

perimeteroftheringsothatisrmlyattached.

[FIG. 2]

FIG. 1

FIG. 2

FIG. 3

66oneida-air.com

Assembly Instructions (Continued)

Pushthe1/4"-20 X 3/4" CarriageBolts(M3)

upfrombelowthroughpre-punchedholesand

casterplateholesonthe3"LockingCasters

(M2).Securewith1/4"Nylocknuts(M4).[FIG.

4a]Whenassembledproperlyandthedollyis

turnedupright,thenutswillbeontheunderside

ofthedolly.[FIG. 4b]

PlacetheDrum(J)ontheDolly(M).Thenplace

theLid(H)ontheDrum(J).[FIG. 5]

Installationiscomplete!

FIG. 4a

Carriage Bolt

Dolly

Caster

Nut

FIG. 4b

FIG. 5

Customer Service Dept.

1-866-387-8822 • support@oneida-air.com

1001 West Fayette Street, Syracuse, NY 13204 U.S.A.

ank you for your business!

Regardless of where you purchased your system, if you have any

questions or issues with missing / damaged parts, please call

Oneida Air Systems rst to let us help resolve your problem.

We fully stand behind the quality of our product and place the

utmost value on our customer’s opinion.

We want to do everything possible to make your purchase and

experience with Oneida Air Systems a good one!

Oneida Air Systems AXD000002-HD-55 Owner's manual

Oneida Air Systems AXD000002-HD-55 Owner's manual

Oneida Air Systems AXD000002-HD-55 Owner's manual

Related papers

Other documents