EtherWAN EX42000 Series Quick Installation Guide

EX42000 Series
Brand
EtherWAN
Model
EX42000 Series
Type
Quick Installation Guide

EtherWAN EX42000 Series is an industrial unmanaged switch designed for harsh environments, offering reliable and efficient network connectivity for industrial applications. With its DIN rail mountable design, wide operating temperature range, and robust construction, it's ideal for factory automation, traffic control systems, and other industrial settings. The switch features 10/100Base-TX ports for connecting Ethernet devices, 100Base-FX port for fiber connectivity, and WDM 100Base-BX port for long-distance data transmission.

EtherWAN EX42000 Series is an industrial unmanaged switch designed for harsh environments, offering reliable and efficient network connectivity for industrial applications. With its DIN rail mountable design, wide operating temperature range, and robust construction, it's ideal for factory automation, traffic control systems, and other industrial settings. The switch features 10/100Base-TX ports for connecting Ethernet devices, 100Base-FX port for fiber connectivity, and WDM 100Base-BX port for long-distance data transmission.

W70G-EX424KVQ3 Page 1
Installation Guide
EX42000 Series | Industrial Unmanaged Switch
Copyright 2023 EtherWAN Systems, Inc. All Rights Reserved 01/03/2023
1 Unpacking
Open the carton and unpack the items. Your package
should include:
▪ One EX42000 Switch
If any items are missing or damaged, notify your
EtherWAN representative. If possible, save the carton
and packing material in case you need to ship or store
the switch in the future.
2 Equipment Needed
▪ Category 5 or better cable for RJ-45 ports
▪ Appropriate fiber cable for fiber ports
3 Select a Location
▪ Installation: DIN rail. Place the device on the DIN
rail from above using the slot. Push the front of
the device toward the mounting surface until it
audibly snaps into place.
▪ Choose a dry area with ambient temperature
between -10°C to +60°C (14°F to 140°F).
▪ Keep away from heat sources, sunlight, warm air
exhausts, hot-air vents, and heaters.
▪ Be sure there is adequate airflow.
4 Connect to the Data Ports
Depending on the model, your switch can have the
following ports:
▪ 10/100Base-TX Ports
▪ 100Base-FX Port
▪ WDM 100Base-BX Port
5 Connect Power
Power Supply is via a DC terminal block power input,
12-48VDC
Terminal Block
PWR
GND
Power-Up Sequence
When the switch is powered up:
▪ All Link/ACT LEDs blink momentarily.
▪ The Power LED lights up and stays lit.
▪ LEDs for every port connected to a device will
flash, as the switch conducts a brief Power On Self-
Test (POST).
CAUTION: This equipment is designed to permit the
connection of the earthed conductor of the DC supply
circuit to the earthing conductor at the equipment.
For power connection, the following conditions must
be met:
▪ This equipment shall be connected to directly to
the DC supply system earthing electrode
conductor or to a bonding jumper from an
earthing terminal bar or bus to which the DC
supply system earthing electrode conductor is
connected.
▪ This equipment shall be located in the same
immediate area (such as, adjacent cabinets) as
any other equipment that has a connection
between the earthed conductor of the same DC
supply circuit and the earthing conductor, and
also the point of earthing of the DC system. The
DC system shall not be earthed elsewhere.
▪ The DC supply source is to be located within the
same premises as the equipment.
▪ Switching or disconnecting devices shall not be in
the earthed circuit conductor between the DC
source and the point of connection of the earthing
electrode conductor.
W70G-EX424KVQ3 Page 2
Installation Guide
EX42000 Series | Industrial Unmanaged Switch
Copyright 2023 EtherWAN Systems, Inc. All Rights Reserved 01/03/2023
6 Port Status LED Indicators
LED
State
Indication
10/100TX or 100FX/BX
LINK/ACT
Steady
Network connection
established
Flashing
Transmitting or receiving data
100
Steady
Transfer at 100Mbps
Off
Transfer at 10Mbps
7 DIN Rail Installation
DIN-Rail Assembly Startup, and Dismantling
▪ Assembly: Place the Switch on the DIN rail from
above using the slot. Push the front of the Switch
toward the mounting surface until it audibly snaps
into place.
▪ Startup: Connect the supply voltage to start up the
Switch via the terminal block.
▪ Dismantling: Pull out the lower edge and then
remove the Switch from the DIN rail.
Manufacturer information:
EtherWAN Systems, Inc.
33F, No. 93, Sec. 1, Xintai 5th Rd., Xizhi Dist., New
Taipei City, 221 Taiwan
The full product manual can be downloaded from:
www.etherwan.com
  • Page 1 1
  • Page 2 2

EtherWAN EX42000 Series Quick Installation Guide

EX42000 Series
Brand
EtherWAN
Model
EX42000 Series
Type
Quick Installation Guide

EtherWAN EX42000 Series is an industrial unmanaged switch designed for harsh environments, offering reliable and efficient network connectivity for industrial applications. With its DIN rail mountable design, wide operating temperature range, and robust construction, it's ideal for factory automation, traffic control systems, and other industrial settings. The switch features 10/100Base-TX ports for connecting Ethernet devices, 100Base-FX port for fiber connectivity, and WDM 100Base-BX port for long-distance data transmission.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers