Manson SBC-1220 User manual

Manson
Brand
Manson
Model
SBC-1220
Category
Security device components
Type
User manual

This manual is also suitable for

Manson SBC-1220 is a controller module designed to be used with solenoid switches that use less than 1.5A coil current. The device has a microprocessor control sealed with epoxy resin constantly scans the voltages of the main battery and compares them with set values. Based on this, it makes the solenoid switch either connect or disconnect with appropriate time delays. This merging of MCU electronic control and electro-mechanical solenoid switch is a cost- effective and flexible way for DC power management.

Manson SBC-1220 is a controller module designed to be used with solenoid switches that use less than 1.5A coil current. The device has a microprocessor control sealed with epoxy resin constantly scans the voltages of the main battery and compares them with set values. Based on this, it makes the solenoid switch either connect or disconnect with appropriate time delays. This merging of MCU electronic control and electro-mechanical solenoid switch is a cost- effective and flexible way for DC power management.

SBC-1120 USER MANUAL
Description
The controller module is designed to use with solenoid switches which use less than 1.5A coil current. It allows users to
choose the suitable solenoid switch for the right application.
The module has a microprocessor control sealed with epoxy resin. It constantly scans the voltages of main battery and
compare with it set values to make the solenoid switch for either connection or disconnection with appropriate time
delays.
This merging of MCU electronic control and electro-mechanical solenoid switch for large current conductivity with little
voltage drop loss is a cost effective and flexible way for DC power management.
Typical applications are: automatic separation of main (starter) and auxiliary batteries during charging and discharging
according to the state of the charge level of the main battery. Dual battery or multi-banks battery system such as 4W
vehicles, RD Trailer, solar charged batteries, Ham radio backup and etc.
There is a manual over-ride function to force connect two batteries for emergency starting and other application.
The Controller
Mounting Bracket and Connected wire
Type A: 1.Mounting Bracket (to solenoid large terminal which shares with Positive connection of Main Battery) 27mm
Length; 2.Black Wire Length 35+150mm
Type A Diagram
Type B: 1.Mounting Bracket (to solenoid large terminal which shares with Positive connection of Main Battery) 39mm
Length; 2.Black Wire Length 55+150mm
Type B Diagram
Installation Diagram
Specification
Models SBC-1120
Battery Voltage(Main and Auxiliary) 12VDC
Isolator Switch ON(Connect) Voltage 13.1VDC
Isolator Switch Off(Disconnect) Voltage 12.6VDC
Maximum Operating Voltage 15.5VDC
Over Voltage Protection Voltage 16VDC
Operating Current Consumption (solenoid on) 1.5A MAX.
Idle Current Consumption 6m A
Delay Time for Switch OFF 15 seconds
Indication Green LED
Mounting Bracket and Connected wire Optional type A or B
Dimension 10x16x16mm
Weight 32g
*SPECIFICATIIONS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE*
REV.0 2010/04 7673-1120-0560
  • Page 1 1
  • Page 2 2

Manson SBC-1220 User manual

Manson
Brand
Manson
Model
SBC-1220
Category
Security device components
Type
User manual
This manual is also suitable for

Manson SBC-1220 is a controller module designed to be used with solenoid switches that use less than 1.5A coil current. The device has a microprocessor control sealed with epoxy resin constantly scans the voltages of the main battery and compares them with set values. Based on this, it makes the solenoid switch either connect or disconnect with appropriate time delays. This merging of MCU electronic control and electro-mechanical solenoid switch is a cost- effective and flexible way for DC power management.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents