TRINAMIC / ANALOG DEVICES PD42-3-1240-TMCL User manual

Brand: TRINAMIC / ANALOG DEVICES

Model: PD42-3-1240-TMCL

Type: User manual

PANdrive™for Stepper PANDRIVE™

PD42-x-1240 Hardware Manual

Hardware Version V1.10 | Document Revision V1.03 •2020-MAY-05

The PANdrive™PD42-1-1240, PD42-2-1240, PD42-3-1240 amd PD42-4-1240 are small and compact full

mechatronic solutions including NEMA17 / 42mm ﬂange size stepper motors, the TMCM-1240 con-

troller / driver electronics and TRINAMIC™sensOstep™encoder for step-loss detection.

Features

•Stepper Motor NEMA17 / 42mm

•0.22 - 0.7Nm

•with controller/driver

•Linear and sixPoint™ramps

•+10. . . 30V DC supply voltage

•Up to 2A RMS motor current

•RS485, CAN & USB interface

•integrated sensOstep encoder and

support for external encoder

•S/D interface

•multi-purpose inputs and outputs

Applications

•Laboratory Automation

•Manufacturing

•Semiconductor Handling

•Robotics

•Factory Automation

•Test & Measurement

•Life Science

•Biotechnology

•Liquid Handling

Simpliﬁed Block Diagram

10… 30V DC

Microcontroller

EEPROM

I/Os

Step

Motor

RS485

MOSFET

Driver

Stage

Energy Efficient

Driver

TMC262

Motion

Controller

Pre-Driver

USB

CAN

DC/DC

Encoder

PD42-x-1240

Terms of delivery and rights to technical change reserved.

Download newest version at: www.trinamic.com

Read entire documentation.

PD42-x-1240 Hardware Manual •Hardware Version V1.10 | Document Revision V1.03 •2020-MAY-05 2 / 34

Contents

3.1 Dimensions of PD42-x-1240 ...................................... 8

3.2 Stepper motor .............................................. 9

3.3 Integrated sensOstep™encoder .................................... 10

4.1 Power Supply Input Connector ..................................... 12

4.2 Motor Connector ............................................. 12

4.3 RS485 + CAN Connector ......................................... 13

4.4 USB Connector .............................................. 13

4.5 I/O Connector ............................................... 14

7.1 Analog input IN0 ............................................. 17

7.2 Digital inputs IN1 and IN2 ........................................ 17

7.3 HOME/STOP_L/STOP_R switch inputs ................................. 18

7.4 External incremental encoder input .................................. 18

7.5 Step/Direction inputs .......................................... 19

8.1 RS485 .................................................... 20

8.2 CAN ..................................................... 21

10.1 PD42-1-1240 Torque Curve ....................................... 24

10.2 PD42-2-1240 Torque Curve ....................................... 24

10.3 PD42-3-1240 Torque Curve ....................................... 25

10.4 PD42-4-1240 Torque Curve ....................................... 25

16.1 Producer Information .......................................... 32

16.2 Copyright ................................................. 32

16.3 Trademark Designations and Symbols ................................ 32

Terms of delivery and rights to technical change reserved.

Download newest version at www.trinamic.com

PD42-x-1240 Hardware Manual •Hardware Version V1.10 | Document Revision V1.03 •2020-MAY-05 3 / 34

16.4 Target User ................................................ 32

16.5 Disclaimer: Life Support Systems ................................... 32

16.6 Disclaimer: Intended Use ........................................ 32

16.7 Collateral Documents & Tools ..................................... 33

17.1 Hardware Revision ............................................ 34

17.2 Document Revision ............................................ 34

Terms of delivery and rights to technical change reserved.

Download newest version at www.trinamic.com

PD42-x-1240 Hardware Manual •Hardware Version V1.10 | Document Revision V1.03 •2020-MAY-05 4 / 34

1 Features

The PANdrive™PD42-1-1240, PD42-2-1240, PD42-3-1240 amd PD42-4-1240 are small and compact full

mechatronic solutions including NEMA17 / 42mm ﬂange size stepper motors, the TMCM-1240 controller /

driver electronics and TRINAMIC™sensOstep™encoder for step-loss detection. The four PANdrives include

stepper motor with diﬀerent lengths and diﬀerent holding torques (PD42-1-1240: 0.22Nm, PD42-2-1240:

0.36Nm, PD42-3-1240: 0.44Nm and PD42-4-1240: 0.7Nm) but, same electronics and encoder setup. The

PANdrives support both, stand-alone operation e.g. using the on-board I/Os together with the build-in

TMCL scripting feature and remote operation using one of the available communication interfaces and

even a mixture of both.

Motion Controller

•Motion proﬁle calculation in real-time

•On the ﬂy alteration of motor parameters (e.g. position, velocity, acceleration)

•Linear and unique sixPoint™ramp in hardware

•Encoder interface and Reference / Stop switch inputs

Driver

•Motor current: up to 2A RMS (2.2A RMS max. / 3.1A peak, programmable in software)

•Supply voltage: +24V DC (+10. . . +30V DC)

•256 microsteps per fullstep

•spreadCycle™highly dynamic current control chopper

•stealthChop™for quiet operation and smooth motion

•programmable Step/Dir interface for driver-only applications with microstep interpolation

Encoder

•integrated sensOstep absolut position magnetic encoder (resolution: 1024 increments per rotation)

for step-loss detection under all operating conditions and positioning supervision (accuracy: +/- 5

encoder steps)

•support for external A/B incremental encoder in addition / as an alternative for the integrated en-

coder

•programmable encoder scaling and support for motor stop on encoder deviation

Interfaces

•RS485 interface (up-to 1Mbit/s)

•CAN interface (up-to 1Mbit/s)

•USB 2.0 full speed (12Mbit/s) device interface (micro-USB connector)

•Step/Dir input (optically isolated)

•Left and Right STOP switch inputs (optically isolated, shared with Step/Dir inputs)

•2 general purpose digital inputs

•Encoder input for incremental A/B encoder signals (shared with general purpose digital inputs)

•1 analog input (0..10V nom. input range)

Terms of delivery and rights to technical change reserved.

Download newest version at www.trinamic.com

PD42-x-1240 Hardware Manual •Hardware Version V1.10 | Document Revision V1.03 •2020-MAY-05 5 / 34

•HOME switch input (shared with analog input)

Software

•TMCL™remote (direct mode) and standalone operation (memory for up to 1024 TMCL™commands),

fully supported by TMCL-IDE (PC based integrated development environment). Please see PD42-x-

1240 TMCL ﬁrmware manual for more details

•CANopen ﬁrmware with CANopen standard protocol stack for the CAN interface. Please see PD42-

x-1240 CANopen ﬁrmware manual for more details.

Terms of delivery and rights to technical change reserved.

Download newest version at www.trinamic.com

PD42-x-1240 Hardware Manual •Hardware Version V1.10 | Document Revision V1.03 •2020-MAY-05 6 / 34

2 Order Codes

The combination of motor and motor mounted controller/driver electronic is currently available with four

stepper motors (diﬀerent length and holding torque):

The length of the PANdrives is speciﬁed without the length of the axis. For the overall length of the product

please add 26mm

Order Code Description Size (LxWxH)

PD42-1-1240-TMCL PANdrive™with NEMA17 stepper motor, 0.22Nm

max. TMCM-1240 electronics, 2A RMS, +24V,

RS485, CAN, USB, sensOstep™encoder, TMCL

ﬁrmware

42mm x 42mm x 47mm

PD42-2-1240-TMCL PANdrive™with NEMA17 stepper motor, 0.36Nm

max. TMCM-1240 electronics, 2A RMS, +24V,

RS485, CAN, USB, sensOstep™encoder, TMCL

ﬁrmware

42mm x 42mm x 51mm

PD42-3-1240-TMCL PANdrive™with NEMA17 stepper motor, 0.44Nm

max. TMCM-1240 electronics, 2A RMS, +24V,

RS485, CAN, USB, sensOstep™encoder, TMCL

ﬁrmware

42mm x 42mm x 60mm

PD42-4-1240-TMCL PANdrive™with NEMA17 stepper motor, 0.7Nm

max. TMCM-1240 electronics, 2A RMS, +24V,

RS485, CAN, USB, sensOstep™encoder, TMCL

ﬁrmware

42mm x 42mm x 73mm

PD42-1-1240-CANopen PANdrive™with NEMA17 stepper motor, 0.22Nm

max. TMCM-1240 electronics, 2A RMS, +24V,

RS485, CAN, USB, sensOstep™encoder, CANopen

ﬁrmware

42mm x 42mm x 47mm

PD42-2-1240-CANopen PANdrive™with NEMA17 stepper motor, 0.36Nm

max. TMCM-1240 electronics, 2A RMS, +24V,

RS485, CAN, USB, sensOstep™encoder, CANopen

ﬁrmware

42mm x 42mm x 51mm

PD42-3-1240-CANopen PANdrive™with NEMA17 stepper motor, 0.44Nm

max. TMCM-1240 electronics, 2A RMS, +24V,

RS485, CAN, USB, sensOstep™encoder, CANopen

ﬁrmware

42mm x 42mm x 60mm

PD42-4-1240-CANopen PANdrive™with NEMA17 stepper motor, 0.7Nm

max. TMCM-1240 electronics, 2A RMS, +24V,

RS485, CAN, USB, sensOstep™encoder, CANopen

ﬁrmware

42mm x 42mm x 73mm

Table 1: Order Code

Terms of delivery and rights to technical change reserved.

Download newest version at www.trinamic.com

PD42-x-1240 Hardware Manual •Hardware Version V1.10 | Document Revision V1.03 •2020-MAY-05 7 / 34

A cable loom set is available for this module:

Order Code Description

TMCM-1240-CABLE Cable loom for TMCM-1240:

•1x cable loom for power supply connector (cable length 200mm, 4pin

JST PH connector at one end, open wires at the other end)

•1x cable loom for RS485 + CAN connector (cable length 200mm, 5pin

JST PH connector at one end, open wires at the other end)

•1x cable loom for motor connector (cable length 200mm, 4pin JST PH

connector at one end, open wires at the other end)

•1x cable loom for I/O connector (cable length 200mm, 8pin JST PH

connector at one end, open wires at the other end)

•1x Micro-USB cable

Table 2: TMCM-1240 Cable Loom

The TMCM-1240 controller/driver electronics is also available separately. Please refer to TMCM-1240 hard-

ware manual for further details.

Terms of delivery and rights to technical change reserved.

Download newest version at www.trinamic.com

PD42-x-1240 Hardware Manual •Hardware Version V1.10 | Document Revision V1.03 •2020-MAY-05 8 / 34

3 Mechanical and Electrical Interfacing

All PD42-x-1240 consist of one out of four available NEMA17 / 42mm stepper motors with 2A RMS rated coil

current with the same TMCM-1240 controller / driver electronics mounted on its backside and integrated

sensOstep™encoder. The PD42-1-1240 uses the QSH4218-34-20-022 stepper motor with 0.22Nm holding

torque, the PD42-2-1240 uses the QSH4218-38-20-036 stepper motor with 0.36Nm holding torque, the

PD42-3-1240 uses the QSH4218-47-20-044 stepper motor with 0.44Nm holding torque and the PD42-4-

1240 uses the QSH4218-60-20-070 stepper motor with 0.7Nm holding torque. Please see also stepper

motor manuals and TMCM-1240 hardware and ﬁrmware manuals for more details.

NOTICE Note: In order to make proper use of the integrated sensOstep™encoder (the

sensor IC is placed on the bottom of the pcb) the TMCM-1240 electronics should

not be removed/moved relative to the motor. In case the integrated encoder

feature is not used, the electronics may be moved or even removed from the

motor and placed somewhere else according to application requirements.

3.1 Dimensions of PD42-x-1240

Figure 1: PD42-x-1240 with diﬀerent NEMA17 / 42mm stepper motors (all dimensions in mm)

Terms of delivery and rights to technical change reserved.

Download newest version at www.trinamic.com

PD42-x-1240 Hardware Manual •Hardware Version V1.10 | Document Revision V1.03 •2020-MAY-05 9 / 34

3.2 Stepper motor

Main characteristics of the four diﬀerent motors available as part of the PD42-x-1240 PANdrive™:

Speciﬁcations Unit PD42-1-1240 PD42-2-1240 PD42-3-1240 PD42-4-1240

Step angle °1.8 1.8 1.8 1.8

Step angle accuracy % +/-5 +/-5 +/-5 +/-5

Ambient temperature °C -20. . . +50 -20. . . +50 -20. . . +50 -20. . . +50

Max. motor temperature °C 80 80 80 80

Shaft radial play (450g load) mm 0.02 0.02 0.02 0.02

Shaft axial play (450g load) mm 0.08 0.08 0.08 0.08

Max radial force (20mm

from front ﬂange)

N 28 28 28 28

Max axial force N 10 10 10 10

Rated voltage V 2.0 2.4 2.4 4.4

Rated phase current A 2.0 2.0 2.0 2.0

Phase resistance at 20°CΩ1.0 1.2 1.4 2.3

Phase inductance (typ.) mH 1.6 2.2 2.1 6.0

Holding torque Nm 0.22 0.36 0.44 0.70

Insulation class B B B B

Rotor inertia g cm235 57 68 102

Weight kg 0.22 0.24 0.35 0.5

Table 3: NEMA17 / 42mm stepper motor technical data

Terms of delivery and rights to technical change reserved.

Download newest version at www.trinamic.com

PD42-x-1240 Hardware Manual •Hardware Version V1.10 | Document Revision V1.03 •2020-MAY-05 10 / 34

3.3 Integrated sensOstep™encoder

The PD42-x-1240 PANdrives oﬀer integrated sensOstep™encoders based on hall sensor technology. As

the name “sensOstep™“ already indicates intended use of this type of compact and highly integrated

encoder is step loss detection of motor movements. As soon as the motor has been moved to a new

location the position may be veriﬁed using this encoder feedback. In case the stepper motor has lost one

or multiple steps during movement e.g. due to overload / any obstacle encountered during movement

the motor axes will jump for at least one electrical period / 4 full steps. This can be detected using the

integrated encoder. In addition, step losses may be already detected during motor movements using

the “deviation” setting available as part of the TMCL ﬁrmware (see PD42-x-1240 / TMCM-1240 ﬁrmware

manual for more details).

While the encoder oﬀers 10bit (1024 steps) resolution per motor revolution the absolute position informa-

tion is less accurate and depends on the displacement of the hall sensor based encoder IC relative to the

magnet and motor axis among other factors. Every PANdrive™has been tested for maximum deviation

of +/- 5 encoder steps (static performance) relative to commanded microstep target position during ﬁnal

tests after assembly at our factory. This will ensure more than adequate performance of the integrated

sensOstep™encoder for step loss detection during motor movements.

NOTICE Do not disassemble PANdrive™when using integrated encoder In order to

make proper use of the integrated sensOstep™encoder (the sensor IC is placed

on the bottom center of the pcb) the TMCM-1240 electronics should not be

removed/moved relative to the motor! Otherwise encoder performance might

suﬀer / not work.

Note: In case the integrated encoder feature is not used, the TMCM-1240

electronics may be moved or even removed from the motor and placed

somewhere else according to application requirements.

NOTICE Keep the electronics free of (metal) particles! The integrated sensOstep™

encoder uses a magnet at the end of the motor axis in order to monitor position

of the motor axis. The magnet naturally attracts especially tiny metal particles.

These particles might be held on the top side of the PCB and – even worse

– start moving in accordance with the rotating magnetic ﬁeld as soon as the

motor starts moving. This might lead to shorts of electronic contacts / wires on

the board and totally erratic behavior of the module! Use compressed air for

cleaning the module if necessary (especially in prototype setups).

In order to prevent shorts and better protect the electronics the TMCM-1240

printed circuit board is coated after assembly of components.

Terms of delivery and rights to technical change reserved.

Download newest version at www.trinamic.com

PD42-x-1240 Hardware Manual •Hardware Version V1.10 | Document Revision V1.03 •2020-MAY-05 11 / 34

4 Connectors

The PD42-x-1240 oﬀers ﬁve connectors including the motor connector which is used for connecting the

motor coils to the electronics. There is one motor and one power supply connector - both with four pins -

and two interface connectors - one with ﬁve pins for RS485 and CAN and a dedicated micro-USB connector.

All other inputs and outputs are concentrated on one 8 pin connector.

NOTICE Start with power supply OFF and do not connect or disconnect motor dur-

ing operation! Motor cable and motor inductivity might lead to voltage spikes

when the motor is (dis)connected while energized. These voltage spikes might ex-

ceed voltage limits of the driver MOSFETs and might permanently damage them.

Therefore, always switch oﬀ / disconnect power supply or at least disable driver

stage before connecting / disconnecting motor.

USB

Motor

Power

RS485 + CAN

I/O

Figure 2: PD42-x-1240 connectors

Connector Types and Mating Connectors

Connector Connector type on-board Mating connector type

Power JST B4B-PH-K-S

(JST PH series, 4pins, 2mm pitch)

Connector housing: JST PHR-4

Contacts: JST SPH-002T-P0.5S

Wire: 0.22mm2, AWG 24

Motor JST B4B-PH-K-S

(JST PH series, 4pins, 2mm pitch)

Connector housing: JST PHR-4

Contacts: JST SPH-002T-P0.5S

Wire: 0.22mm2, AWG 24

RS485+CAN JST B5B-PH-K-S

(JST PH series, 5pins, 2mm pitch)

Connector housing: JST PHR-5

Contacts: JST SPH-002T-P0.5S

Wire: 0.22mm2, AWG 24

USB USB-micro B female connector USB-micro B male connector

I/O JST B8B-PH-K-S

(JST PH series, 8pins, 2mm pitch)

Connector housing: JST PHR-8

Contacts: JST SPH-002T-P0.5S

Wire: 0.22mm2, AWG 24

Table 4: Connector Types and Mating Connectors of the PD42-x-1240

Terms of delivery and rights to technical change reserved.

Download newest version at www.trinamic.com

PD42-x-1240 Hardware Manual •Hardware Version V1.10 | Document Revision V1.03 •2020-MAY-05 12 / 34

4.1 Power Supply Input Connector

The PD42-x-1240 oﬀers one 4pin JST PH series power supply input connector. In addition to main power

supply input and related ground connection this connector oﬀers a separate logic supply input with the

option to keep the on-board logic alive while the driver stage is switched oﬀ. It is not necesary to connect

the logic supply input in case separate supplies are not required as the main power supply input will

always supply power to the driver stage and the logic part.

The power supply input connector oﬀers a driver enable input. This input has to be connected to any

voltage above 3.5V up-to max. supply voltage of 30V in order to enable the driver stage. Leaving this pin

unconnected or connected to ground (voltage below 2.4V) will disable the driver stage regardless of any

settings in software. This input may be connected to main power supply input permanently in case an

enable input in hardware is not required.

Power Supply Connector Pin Assigment

Pin Label Direction Description

1 GND Power (GND) Common system supply and signal ground

2 VMAIN Power (input) Main power supply input for the driver and on-board logic

10. . . 30V

3 Enable Digital input Driver enable input. A voltage above 3.5V is required here in

order to enable the on-board stepper motor driver. This in-

put maybe connected to main power supply input in order to

enable the driver stage (+24V tolerant input).

4 VLOGIC Power (input) Optional separate power supply input for the on-board logic

10. . . 30V

Table 5: Power Supply Connector Pin Assignment

NOTICE Do not connect or disconnect motor during operation! Motor cable and mo-

tor inductivity might lead to voltage spikes when the motor is (dis)connected

while energized. These voltage spikes might exceed voltage limits of the driver

MOSFETs and might permanently damage them. Therefore, always switch oﬀ

/ disconnect power supply or at least disable driver stage before connecting /

disconnecting motor.

NOTICE Take care of polarity, wrong polarity can destroy the board!

NOTICE Connect Enable pin to voltage >3.5V in order to enable motor movements!

4.2 Motor Connector

A second 4pin JST PH series connector is available for connection of a 2-phase bipolar stepper motor.

Motor Connector Pin Assignment

Pin Label Direction Description

1 B1 out Pin 1 of motor coil B

2 B2 out Pin 2 of motor coil B

Terms of delivery and rights to technical change reserved.

Download newest version at www.trinamic.com

PD42-x-1240 Hardware Manual •Hardware Version V1.10 | Document Revision V1.03 •2020-MAY-05 13 / 34

Pin Label Direction Description

3 A1 out Pin 1 of motor coil A

4 A2 out Pin 2 of motor coil A

Table 6: Motor Connector Pin Assignment

NOTICE Do not connect or disconnect motor during operation! Motor cable and mo-

tor inductivity might lead to voltage spikes when the motor is (dis)connected

while energized. These voltage spikes might exceed voltage limits of the driver

MOSFETs and might permanently damage them. Therefore, always switch oﬀ

/ disconnect power supply or at least disable driver stage before connecting /

disconnecting motor.

NOTICE Do not mix-up power supply and motor connectors!

4.3 RS485 + CAN Connector

For serial communication the PD42-x-1240 oﬀers selection between RS485, CAN and USB interfaces. While

the USB interface is available for conﬁguration and service of the board, mainly (e.g. parameter settings,

ﬁrmware updates) a 5-pin JST PH series connector oﬀers 2-wire RS485 and CAN interfaces for in system

communication.

NOTICE Due to hardware ressource sharing USB and CAN communication interfaces are

not available at the same time. As soon as USB is physically attached to a host or

hub the CAN interface will be switched oﬀ.

RS485 + CAN Connector Pin Assignment

Pin Label Direction Description

1 GND Power (GND) Common system supply and signal ground

2 RS485+ Bidirectional RS485 interface, diﬀ. signal (non-inverting)

3 RS485- Bidirectional RS485 interface, diﬀ. signal (inverting)

4 CAN_H Bidirectional CAN interface, diﬀ. signal (non-inverting)

5 CAN_L Bidirectional CAN interface, diﬀ. signal (inverting)

Table 7: RS485 + CAN Connector Pin Assignment

4.4 USB Connector

For serial communication the PD42-x-1240 oﬀers selection between RS485, CAN and USB interfaces. The

USB interface via on-board micro-USB connector (type B) is available for conﬁguration and service of the

board, mainly (e.g. parameter settings, ﬁrmware updates). The USB device interface supports full speed

(12Mbit/s) communication and supports bus powered and self-powered operation. During bus-powered

operation the low voltage logic part of the board will be powered, only. This includes the microcontroller

and the non-volatile memory and therefore allows parameter settings and ﬁrmware updates of the board

Terms of delivery and rights to technical change reserved.

Download newest version at www.trinamic.com

PD42-x-1240 Hardware Manual •Hardware Version V1.10 | Document Revision V1.03 •2020-MAY-05 14 / 34

using a standard USB cable, only. Of course, for any motor movement main supply via supply input

connector is required.

NOTICE Due to hardware ressource sharing USB and CAN communication interfaces are

not available at the same time. As soon as USB is physically attached to a host or

hub the CAN interface will be switched oﬀ.

USB Connector Pin Assignment

Pin Label Direction Description

1 VBUS Power (+5V) USB +5V nom. power supply input

2 D- Bidirectional USB interface, diﬀ. signal (inverting)

3 D+ Bidirectional USB interface, diﬀ. signal (inverting)

4 ID Input connected to GND (via 100k resistor)

5 GND Power (GND) Common system supply and signal ground

Table 8: USB Connector Pin Assignment

4.5 I/O Connector

The PD42-x-1240 oﬀers several inputs (two of them optically isolated) and one digital (open-drain) output.

The inputs include support for stop switches (left and right), home switch, step/direction, incremental A/B

channel encoder and analog (0. . . +10V) input. All this functionality is available via one 8pin JST PH series

I/O connector.

I/O Connector Pin Assignment

Pin Label Direction Description

1 GND Power (GND) Common system supply and signal ground

2 IN0/HOME Input Analog input (0. . . +10V)

HOME switch input

+24V tolerant, programmable (separate) pull-up to +5V

3 IN1/ENC_A Input General purpose digital input

Incremental encoder input channel A

+24V tolerant, programmable pull-up (for IN1/IN2 together) to

+5V

4 IN2/ENC_B Input General purpose digital input

Incremental encoder input channel B

+24V tolerant, programmable pull-up (for IN1/IN2 together) to

+5V

5 STOP_L/STEP Input STOP left switch input

STEP pulse input

input optically isolated, +24V compatible

6 STOP_R/DIR Input STOP right switch input

DIR input

input optically isolated, +24V compatible

Terms of delivery and rights to technical change reserved.

Download newest version at www.trinamic.com

PD42-x-1240 Hardware Manual •Hardware Version V1.10 | Document Revision V1.03 •2020-MAY-05 15 / 34

Pin Label Direction Description

7 ISO_COM Power Common positive (+24V_ISO) or negative (GND_ISO) isolated

supply input for optically isolated inputs

8 OUT0 Output (OD) Open-Drain output. Output will be pulled low when activated.

Voltages up-to logic supply input level (or main supply input in

case separate logic supply is not used) are supported here. Max.

continuous pull-down current: 100mA

Table 9: I/O Connector Pin Assignment

All pins marked light green oﬀer functional isolation towards main supply input. In case this is not required

ISO_COM may be connected to main ground or supply input, of course. The opto-couppler used are AC

types. This way, either high side switches or low side switches for both inputs are supported.

5 On-Board LEDs

The board oﬀers two LEDs in order to indicate board status. The function of both LEDs is dependent on the

ﬁrmware version. With standard TMCL ﬁrmware the green LED should be ﬂashing slowly during operation

and the red LED should be oﬀ. When there is no valid ﬁrmware programmed into the board or during

ﬁrmware update the red and green LEDs are permanently switched on. During reset to factory default

values the green LED will be ﬂashing fast. With CANopen ﬁrmware both LEDs are switched on/oﬀ/ﬂashing

according to standard deﬁntion.

Green LEDRed LED

Figure 3: PD42-x-1240 LEDs

6 Reset to Factory Defaults

It is possible to reset all settings in ﬁrmware for the PD42-x-1240 to factory defaults without establishing

a working communication connection. This might be helpful in case communication parameters of the

preferred interface have been set to unknown values or got lost.

For this procedure two pads on the bottom side of the module have to be shorted (electrically connected

with each other) during power-on.

Please perform the following steps:

1. Switch power supply OFF (and disconnect USB cable if applicable)

2. Short CLK and DIO pads of programming pads on bottom of pcb (see ﬁgure 4)

Terms of delivery and rights to technical change reserved.

Download newest version at www.trinamic.com

PD42-x-1240 Hardware Manual •Hardware Version V1.10 | Document Revision V1.03 •2020-MAY-05 16 / 34

3. Switch power supply ON again (or connect USB again if applicable)

4. Wait until the on-board red and green LEDs start ﬂashing fast (this might take a while)

5. Switch power supply OFF again (and disconnect USB cable if applicable)

6. Remove short between pads

7. After switching power supply ON again (and / or connecting USB cable) all permanent settings have

been restored to factroy defaults

Short these two pads

Figure 4: Reset to factory default settings

Terms of delivery and rights to technical change reserved.

Download newest version at www.trinamic.com

PD42-x-1240 Hardware Manual •Hardware Version V1.10 | Document Revision V1.03 •2020-MAY-05 17 / 34

7 I/Os

The I/O connector (8pin JST PH series) oﬀers one analog input, two non-isolated digital inputs with inte-

grated pull-ups (programmable) and two optically isolated inputs. All inputs can be used for diﬀerent

purposes explained in more detail in the following subsections.

7.1 Analog input IN0

The PD42-x-1240 oﬀers one analog input. The analog input voltage range is approx. 0..+10V. For volt-

ages above +10V saturation takes place but, up-to 30V higher voltages are tolerated without destroying

the input. For analog to digital conversion the integrated ADC of the on-board microcontroller is used.

Resolution of this converter is 12bit (0..4095).

100nF

10k

22k

2k2

+3V3

microcontroller

IN0

+5V

TMCM-1240

pull-up

disabled

0..10V

Figure 5: Analog input IN0

The analog input can be used as digital input, also. There is an integrated pull-up to +5V which can be

switched on of oﬀ in software. When using this input as anlog input the pull-up should be usually switched

oﬀ.

7.2 Digital inputs IN1 and IN2

The PD42-x-1240 oﬀers two digital inputs IN1 and IN2 which accept signals between 0 and 30V with volt-

ages above approx. 2.9V recognized as logical ’1’ and below 1V as logical ’0’. Both inputs oﬀer intergated

pull-ups to +5V which can be switched on or oﬀ in software (always together). When using the inputs with

low-side switches (connected to GND), pull-ups usually should be switched on (default). In case high-side

switches are used the pull-ups must be switched oﬀ. For push-pull signals the pull-ups may be either

switched on or oﬀ.

Terms of delivery and rights to technical change reserved.

Download newest version at www.trinamic.com

PD42-x-1240 Hardware Manual •Hardware Version V1.10 | Document Revision V1.03 •2020-MAY-05 18 / 34

33pF

22k

10k

2k2

+3V3

microcontroller

IN1

IN2

+5V

TMCM-1240

pull-up

enabled

pull-up

disabled

+5V...24V

+5V

Figure 6: Digital inputs IN1 and IN2

7.3 HOME/STOP_L/STOP_R switch inputs

The PD42-x-1240 oﬀers two optically isolated inputs which can be used as left (STOP_L) and right (STOP_R)

stop switch inputs. When enabled in software the STOP_L switch input will stop motor movement in

negative direction (step counter decreasing) while activated. Likewise the STOP_R switch input will stop

motor movement in positive direction (step counter increasing) while activated.

680

6k8

2k2

+3V3

microcontroller

TMCM-1240

STOP_L,

STOP_R

ISO_COM

+24V_ISO

GND_ISO

+24V_ISO

GND_ISO

Figure 7: Stop switch inputs

A separated / isolated supply may be used for the switches - as indicated in the drawing (+24V_ISO and

related GND_ISO) - but, same supply as for the PD42-x-1240 can be used, also, of course.

7.4 External incremental encoder input

The PD42-x-1240 oﬀers an integrated hall-sensor based magnet encoder. In addition, an external incre-

mental A/B encoder may be connected to the two digital inputs IN1 and IN2. Encoder with push-pull

signals (e.g. +5V TTL) and open-drain output signals are supported (single-ended). For open-drain out-

puts the internal pull-ups should be activated in software (default mode).

Terms of delivery and rights to technical change reserved.

Download newest version at www.trinamic.com

PD42-x-1240 Hardware Manual •Hardware Version V1.10 | Document Revision V1.03 •2020-MAY-05 19 / 34

33pF

22k

10k

2k2

+3V3

microcontroller

ENC_A,

ENC_B

+5V

TMCM-1240

+5V

pull-up

enabled

Figure 8: External encoder input

7.5 Step/Direction inputs

The PD42-x-1240 may be used as driver with an external motion controller. In this case the Step/Direction

output signals of the external motion controller may be connected to the optically isolated Step/Dir inputs

of the PD42-x-1240. Please note that these signals should be 24V signals. For lower voltage signals a

simple small signal transistor maybe inserted as level converter.

680

6k8

2k2

+3V3

microcontroller

TMCM-1240

STEP,

DIR

ISO_COM

+24V_ISO

GND_ISO

Figure 9: Step/Direction input

Due to limitations of the opto-isolators the maximum step frequency of these inputs is limited to around

20kHz. For higher motor speed the step interpolator of the driver stage should be activated or the mi-

crostep resolution reduced (default 256 microsteps per fullstep).

Terms of delivery and rights to technical change reserved.

Download newest version at www.trinamic.com

PD42-x-1240 Hardware Manual •Hardware Version V1.10 | Document Revision V1.03 •2020-MAY-05 20 / 34

8 Communication

8.1 RS485

For remote control and communication with a host system the PD42-x-1240 provides a two wire RS485

bus interface. For proper operation the following items should be taken into account when setting up an

RS485 network:

1. BUS STRUCTURE:

The network topology should follow a bus structure as closely as possible. That is, the connection

between each node and the bus itself should be as short as possible. Basically, it should be short

compared to the length of the bus.

c:> node

node

n- 1

node

Host Slave Slave Slave

RS485

termination

resistor

(120 Ohm)

termination

resistor

(120 Ohm)

}

keep distance as

short as possible

Figure 10: RS485 bus structure with termination resistors

2. BUS TERMINATION:

Especially for longer busses and/or multiple nodes connected to the bus and/or high communication

speeds, the bus should be properly terminated at both ends. The PD42-x-1240 does not integrate

any termination resistor. Therefore, 120 Ohm termination resistors at both ends of the bus have to

be added externally.

3. NUMBER OF NODES:

The RS485 electrical interface stadard (EIA-485) allows up to 32 nodes to be connected to a single bus.

The bus transceiver used on the PD42-x-1240 units (SN65HVD1781D) oﬀers a signiﬁcantly reduced

bus load compared to the standard and allows a maximum of 255 units to be connected to a single

RS485 bus using standard TMCL ﬁrmware. Please note: usually it cannot be expected to get reliable

communication with the maximum number of nodes connected to one bus and maximum supported

communication speed at the same time. Instead, a compromise has to be found between bus cable length,

communication speed and number of nodes.

4. COMMUNICATION SPEED:

The maximum RS485 communication speed supported by the PD42-x-1240 hardware is 1Mbit/s. Fac-

tory default is 9600 bit/s. Please see separate PD42-x-1240 TMCL ﬁrmware manual for information

regarding other possible communication speeds below the upper hardware limit.

5. NO FLOATING BUS LINES:

Avoid ﬂoating bus lines while neither the host/master nor one of the slaves along the bus line is

transmitting data (all bus nodes switched to receive mode). Floating bus lines may lead to communi-

cation errors. In order to ensure valid signals on the bus it is recommended to use a resistor network

connecting both bus lines to well deﬁned logic levels.

There are actually two options which can be recommended: Add resistor (bias) network on one side

of the bus, only (120R termination resistor still at both ends):

Terms of delivery and rights to technical change reserved.

Download newest version at www.trinamic.com

Page is loading ...

TRINAMIC / ANALOG DEVICES PD42-3-1240-TMCL User manual

TRINAMIC / ANALOG DEVICES PD42-3-1240-TMCL User manual

TRINAMIC / ANALOG DEVICES PD42-3-1240-TMCL User manual

Related papers

Other documents