Syscom Video XD1000VA User manual

XD1000VA

Mega Analog VP Dome Camera

3-AXIS INFRARED-LED VP

DOME CAMERA

Instruction Manual

2

FCC COMPLIANCE STATEMENT

CE COMPLIANCE STATEMENT

CAUTION : Changes or modifications not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) this device may not cause harmful interference, and (2) this device must

accept any interference received, including interference that may cause undesired operation.

WARNING : This is a Class A poduct. In a domestic environment this product may cause

radio interference in which case the user may be required to take adequate measures.

FCC INFORMATION : This equipment has been tested and found to comply with the limits

for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful interference when the equipment is

operated in a commercial environment. This equipment generates, uses, and can radiate

radio frequency energy and, if not installed and used in accordance with the instruction

manual, may cause harmful interference to radio communications. Operation of this

equipment in a residential area is likely to cause harmful interference in which case the user

will be required to correct the interference at his own expense.

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5.. Do not block any ventilat ion openings. Install in accord ance with the manufacturer`s

instructions.

6. Do not install near any heat sources such as radiators, heat registers, stoves, or other

apparatus (including amplifiers) that produce heat.

7. Only use attachments/accessories specified by the manufacturer.

8. Use only with the ca rt, stand, tripod, bracket, or table specified by

the manufacturer, or sold with the apparatus. When a cart is used,

use caution when moving the cart/apparatus combination to avoid

injury from tip-over.

9. CAUTION - THESE SERVICING IN STRUCTIONS ARE FOR USE BY

QUALIFIED SERVICE PERSONNEL ONLY. TO REDUCE THE RISK OF

ELECTRIC SHOCK DO NOT PERFORM ANY SERVICING OTHER THAN

THAT CONTAINED IN THE OPERATING INSTRUCTIONS UNLESS YOU

ARE QUALIFIED TO DO SO.

10. Use satisfy clause 2.5 of IEC60950-1/UL 60950-1 or Certified/Listed Class 2

power source only.

11. Indoor use only.

EXPLANATION OF GRAPHICAL SYMBOLS

IMPORTANT SAFETY INSTRUCTIONS

3

4

5

6

7

8

9

20

19

20

VIDEO OUT CHECK

CONTENTS & PACKAGE 6

5

1/3" 1.3M

1/3"

EA,

6

2.8-12

7

1. Make mounting holes and cable hole in

the place (ceiling or wall) to which this

dome camera is installed using the

Drilling guide label.

2. Drill the mounting location, using the Drillng guide.

3. Attach the housing to the ceiling using

suitable fasteners, PTS1 5x30 screws

are supplied only use if they are suitable.

4. Tighten a mounting screws.

Press here to adjust the angle.

PTS1 5x30 <4X>

PT-Plug

8

RESET

WHITE BAL

BACKLIGHT

SENS-UP

D-WDR

OFF

WDR

BLC

HSBLC

ATW

AWC->SET

INDOOR

OUTDOOR

MANUAL

AWB

<DAY&NIGHT>

SHARPNESS

LSC

D-EFFECT

DIS

D-ZOOM

SMART D-ZOOM

RETURN

CAM TITLE

MONITOR

CVBS CROP

VIDEO OUT

LANGUAGE

VERSION

RETURN

<RESET>

FACTORY

RETURN

9

MAIN MANU

LENS

EXPOSURE

BACK LIGHT

WHITE BAL

DAY&NIGHT

IMAGE

FUNCTION

SYSTEM

RESET

EXIT

DC

OFF

ATW

AUTO

MAIN MANU

LENS

EXPOSURE

BACK LIGHT

WHITE BAL

DAY&NIGHT

IMAGE

FUNCTION

SYSTEM

RESET

EXIT

MANUAL

OFF

ATW

AUTO

1)

2)

MAIN MANU

LENS

EXPOSURE

BACK LIGHT

WHITE BAL

DAY&NIGHT

IMAGE

FUNCTION

SYSTEM

RESET

EXIT

DC

OFF

ATW

AUTO

SHUTTER

AGC

SENS-UP

BRIGHTNESS

D-WDR

DEFOG

RETURN

AUTO

|▪l▪▪▪▪| 15

OFF

|▪l▪▪▪▪| 30

OFF

RET

< EXPOSURE > MODE

10

AGC, SENS-UP, BRIGHTNESS,

D-WDR and DEFOG function of the camera.

It

1/50000, x2 ~ x30

Adjust the Auto Gain Control level. ▶ 0 - 15

AGC

3) SENS-UP Select the Digital Slow Shutter level. ▶ OFF, AUTO (x2 ~ x30)

BRIGHTNESS Adjust the BRIGHTNESS level. ▶ 0 - 100

D-WDR

DEFOG

Select the Digital WDR.▶ ON, OFF

ON, OFF

POS/SIZE

GRADATION

DEFAULT

Adjust the window position & size

Off, Low, Middle, High

Initialize the setting values

BACKLIGHT

The BACKLIGHT menu is used to the ability to expand the dynamic range and to prevent back

lighting from the image.

1)WDR Select the Dynamic Range level.

* When WDR is ON, D-WDR, D-ZOOM, SMART D-ZOOM

and DIS function can not turn on.

2)BLC Prevents such a back light effect to secure a clear image under All illumination

environments.

Adjust the size of Back Light Compensation area.

3)HLMASK Mask the high light zone with specific color & level.

Adjust the window position & sizeAREA

Initialize the setting valuesDEFAULT

Select the HLMASK area ▶ AREA1 - AREA4SELECT

Adjust the HLMASK area window position & sizeDISPLAY

Adjust the window position & sizeLEVEL

Initialize the setting valuesMODE

Adjust the window position & sizeDEFAULT

MAIN MANU

LENS

EXPOSURE

BACK LIGHT

WHITE BAL

DAY&NIGHT

IMAGE

FUNCTION

SYSTEM

RESET

EXIT

DC

OFF

ATW

AUTO

WDR

GAIN

WDR OFFSET

RETURN

LOW

|▪▪▪▪▪| 0

RET

BLC

GAIN

AREA

DEFAULT

RETURN

MIDDLE

RET

HLBLC

SELECT

DISPLAY

LEVEL

MODE

BLACK MASK

DEFAULT

RETURN

AREA

ON

|▪▪l▪▪| 30

ALL DAY

ON

RET

< BACKLIGHT >

11

WHITE BALANCE

The screen color can be adjusted by using the Auto White Balance function.

It compensates for deviations in the white color caused by changes in the color temperature of

the light source so that the colors are reproduced correctly.

1) AUTO

2)AWC->SET

3)INDOOR

4)OUTDOOR

5)MANUAL

Automatically adjust color temperature.

Automatically readjust only by pressing AWC→SET.

Set the color temperature to 3200°K

Set the color temperature to 6300°K

Manual mode.

User can change Red and Blue gain value manually.

BLUE

RED

0 ~ 100

6)AWB Automatically extended range of color temperature adjustment.

MAIN MANU

LENS

EXPOSURE

BACK LIGHT

WHITE BAL

DAY&NIGHT

IMAGE

FUNCTION

SYSTEM

RESET

EXIT

DC

OFF

ATW

AUTO

MANUAL

BLUE

RED

RETURN

| I | 50

|▪▪I▪▪| 50

RET

▪▪ ▪▪

< WHITE BALANCE > MODE

12

.

CDS

BURST ON, OFF

IR SMART LEVEL 1~15

AREA Adjust the window position & size.

DAY&NIGHT mode are changed according to the brightness of the image.

Use only when the camera is installed in a dark place but the camera is viewing a bright place.

When used in a normal installation, hunting may occur.

13

< DAY&NIGHT > MODE

MAIN MANU

LENS

EXPOSURE

BACK LIGHT

WHITE BAL

DAY&NIGHT

IMAGE

FUNCTION

SYSTEM

RESET

EXIT

DC

OFF

ATW

AUTO

D&N AUTO

DELAY

D N (CDS)

N D (CDS)

RETURN

| I | 5

|▪▪I▪▪| 70

|▪▪I▪▪| 40

RET

▪▪ ▪▪

D&N B&W

BURST

IR SMART

RETURN

ON

RET

The IMAGE menu provides the ability to adjust the SHARPNESS, LSC, D-EFFECT, DIS, D-ZOOM

and SMART D-ZOOM functions of the camera.

1) SHARPNESS Adjust the SHARPNESS level. ▶ 0 - 15

2) LSC Select the lens Lens Shading Compensation. ▶ ON, OFF

3) D-EFFECT FREEZE Select real or still mode ▶ ON, OFF

MIRROR Select OFF, MIRROR, V-FLIP, ROTATE

NEG. IMAGE Select Negative image mode ▶ ON, OFF

4) DIS Select the Digital Image Stability ▶ ON, OFF

5) D-ZOOM Adjust the Digital Zoom level. ▶ x1.0 - x62.0

* When D-ZOOM is ON, SMART D-ZOOM and DIS function can not turn on.

5) SMART D-ZOOM Adjust the Smart Digital Zoom area, level, sensitivity and time.

* When D-ZOOM is ON, D-ZOOM and DIS function can not turn on.

SELECT Select the Smart D-zoom Area ▶ AREA1, AREA2

DISPLAY Select the Smart D-zoom Area display ▶ ON, OFF

SENSITIVITY Adjust the Smart D-zoom Sensitivity ▶ 0 - 60

D-ZOOM Adjust the Digital Zoom level ▶ x1.0 - x62.0

TIME Adjust time level ▶ 0 - 15 (sec)

MAIN MANU

LENS

EXPOSURE

BACK LIGHT

WHITE BAL

DAY&NIGHT

IMAGE

FUNCTION

SYSTEM

RESET

EXIT

DC

OFF

ATW

AUTO

IMAGE

SHARPNESS

LSC

D-EFFECT

DIS

D-ZOOM

SMART D-ZOOM

RETURN

| I | 8

OFF

RET

▪▪ ▪▪

14

SMART D-ZOOM

SELECT

DISPALY

SENSITIVITY

D-ZOOM

TIME

DEFAULT

RETURN

AREA1

ON

|▪▪▪I▪| 60

x2.8

|▪I▪▪▪| 3

RET

IMAGE

SHARPNESS

LSC

D-EFFECT

DIS

D-ZOOM

SMART D-ZOOM

RETURN

| I | 8

OFF

RET

▪▪ ▪▪

1) DNR

2D

3D

SMART NR

Select Digital Noise Reduction.

LEVEL

▶ ON, OFF

▶ ON, OFF (Sensitivity 0 - 100)

Adjust the 3DNR level ▶ 0 - 100

2) MOTION

SELECT

DISPLAY

SENSITIVITY

Detects the Motioned Object in the image. ▶ ON, OFF

MOTION VIEW

DEFAULT

Select the Motion area ▶ AREA1 - AREA4

Adjust the Motion area window position & size

Adjust the Motion sensitivity level ▶ 0 - 60

Select the Motion view ▶ ON, OFF

Initialize the setting values

3) PRIVACY

SELECT

DISPLAY

COLOR

Hide an area you want to hide on the screen.

TRANS

DEFAULT

Select the privacy zone ▶ AREA1 - AREA8

Adjust the Privacy window type, position & size

▶ OFF, INV., MOSAIC, COLOR

Select the privacy zone color ▶ 0 - 15

Select the privacy zone transparency ▶ 0 - 3

Initialize the setting values

4) DEFECT DET

LIVE DPC

STATIC DPC

START

Compensates for bad pixels.

LEVEL

SENS-UP

Select the Live DPC mode ▶OFF, ON, AUTO

▶ ON, OFF

Start the bad pixels correction

Select the Static DPC level ▶ 0 - 60

Select the Sens-up level ▶ x2 - x30

AGC Select the AGC level ▶ 0 - 8

MAIN MANU

LENS

EXPOSURE

BACK LIGHT

WHITE BAL

DAY&NIGHT

IMAGE

FUNCTION

SYSTEM

RESET

EXIT

DC

OFF

ATW

AUTO

FUNCTION

DNR

MOTION

PRIVACY

DEFECT DET

RETURN

OFF

< >FUNCTION

15

MAIN MANU

LENS

EXPOSURE

BACK LIGHT

WHITE BAL

DAY&NIGHT

IMAGE

FUNCTION

SYSTEM

RESET

EXIT

DC

OFF

ATW

AUTO

FUNCTION

DNR

MOTION

PRIVACY

DEFECT DET

RETURN

OFF

RET

<DNR>

DNR

2D

3D

RETURN

ON

OFF

FUNCTION

DNR

MOTION

PRIVACY

DEFECT DET

RETURN

OFF

RET

MOTION

SELECT

DISPLAY

SENSITIVITY

MOTION VIEW

DEFAULT

RETURN

AREA1

ON

|▪▪▪▪▪| 60

ON

RET

FUNCTION

DNR

MOTION

PRIVACY

DEFECT DET

RETURN

OFF

RET

< >PRIVACY

PRIVACY

SELECT

DISPLAY

COLOR

TRANS.

DEFAULT

RETURN

AREA1

COLOR

2

3

RET

FUNCTION

DNR

MOTION

PRIVACY

DEFECT DET

RETURN

OFF

RET

< >DEFECT DET

DEFECT DET

LIVE DPC

STATIC DPC

RETURN

AUTO

ON

RET

FUNCTION

DNR

MOTION

PRIVACY

DEFECT DET

RETURN

OFF

RET

STATIC DPC

START

LEVEL

SENS-UP

AGC

RETURN

| |

x8

|▪▪▪▪▪| 0

RET

▪I▪▪▪ 4

DEFECT DET

CLOSE THE IRIS

THEN

PRESS SET KEY

DEFECT DET

WAITING...

16

17

SYSTEM

The IMAGE menu provides the ability to adjust the CAM TITLE, RS485, MONITOR, CVBS CROP,

VIDEO OUT, LANGUAGE and, VERSION functions of the camera.

1) CAM TITLE Maximum of 15 characters are allowed.

2) MONITOR

LCD

GAMMA

ADAPT. LEVEL

Select the Monitor type ▶ LCD, CRT

BLUE GAIN

RED GAIN

Select the Gamma level ▶ AUTO, USER. USER+Y, 0.45 -1.0

Adjust the Adaptive level ▶ 0 - 100

Adjust the Blue gain level ▶ 0 - 100

Adjust the Red gain level ▶ 0 - 100

3) CVBS CROP ▶ ON, OFF

CRT

BLACK LEVEL

BLUE GAIN

RED GAIN

Select the Gamma level ▶ AUTO, USER. USER+Y, 0.45 -1.0

Adjust the Blue gain level ▶ -50 ~ +50

Adjust the Red gain level ▶ -50 ~ +50

4) VIDEO OUT Select the video out type ▶ NTSC, PAL

5) LANGUAGE OSD menu LANGUAGE (16ea) ▶ ENGLISH etc.

6) VERSION Firmware VERSION

< >SYSTEM

MAIN MANU

LENS

EXPOSURE

BACK LIGHT

WHITE BAL

DAY&NIGHT

IMAGE

FUNCTION

SYSTEM

RESET

EXIT

DC

OFF

ATW

AUTO

SYSTEM

CAM TITLE

MONITOR

CVBS CROP

VIDEO OUT

LANGUAGE

VERSION

RETURN

OFF

LCD

OFF

NTSC

ENGLISH

1.0

RET

< >CAM TITLE

CAM TITLE

0 1 2 3 4 5 6 7 8 9

A B C D E F G H I J K

L M N O P Q R S T U V

WXYZ▶→ ← ↑ ↓ ()

¯ － _■ /=& : ~ , .

← → CLR POS END

________________

SYSTEM

CAM TITLE

MONITOR

CVBS CROP

VIDEO OUT

LANGUAGE

VERSION

RETURN

OFF

LCD

OFF

NTSC

ENGLISH

1.0

RET

18

< >DISPLAY

LCD

GAMMA

ADAPT.LEVEL

BLUE GAIN

RED GAIN

RETURN

AUTO

|▪▪▪▪▪| 100

|▪▪|▪▪| 64

|▪▪|▪▪| 66

RET

CRT

BLACK LEVEL

BLUE GAIN

RED GAIN

RETURN

| | | +

|▪▪|▪▪| +0

RET

▪▪ ▪▪ 0

RESET

The RESET menu provides the ability to adjust the RESET functions of the camera.

1) RESET

FACTORY

Factory initialization of camera settings

Select the RESET mode ▶ RESET, CHANGE

< >RESET

RESET

FACTORY

RETURN

RESET

RET

MAIN MANU

LENS

EXPOSURE

BACK LIGHT

WHITE BAL

DAY&NIGHT

IMAGE

FUNCTION

SYSTEM

RESET

EXIT

DC

OFF

ATW

AUTO

SYSTEM

CAM TITLE

MONITOR

CVBS CROP

VIDEO OUT

LANGUAGE

VERSION

RETURN

OFF

LCD

OFF

NTSC

ENGLISH

1.0

RET

530g

f=2.8~12mm F1.2~360 Varifocal, ICR (D&N)

Fixed mount

BNC Connector

Reset

ENG / JPN / CHN1 / CHN2 / KOR / GER / FRA / ITA

SPA / POL / RUS / POR / NED / TUR / HEB / ARB

OFF / ON

CRT / LCD

NTSC (60Hz) / PAL (50Hz)

Video out

AUTO / USER / USER+Y / 0.45 ~ 1.0

Monitor

0 ~ 15

Freeze OFF / ON

DIS OFF / ON

Smart D-Zoom OFF / ON (x1.0 ~ x62 / 2 zone)

D-Zoom OFF /x1.0 ~ x62

D-Effect OFF / MIRROR / V-FILP / ROTATE

OFF / ON (SMART NR)

3DNR

Privacy Masking OFF / ON (8 Polygone)

Motion Detection OFF / ON (4 zone)

LSC (Shading) OFF / ON

Smart IR Level 1 ~ 15

0 ~ 100

DWDR OFF / ON

ATW / PUSH / INDOOR / OUTDOOR / MANUAL / AWB

SENS-UP

0 ~ 15

0 ~ 100

MAX 4.3 Watts (360mA)

1/3" 1.3M Sony CMOS

1312(H) x 1069(V)

1296(H) x 1041(V)

1000 TVL

NTSC / PAL Changed by OSD

OFF / WDR / BLC / HSBLC

AUTO, 1/60(1/50), FLK ~ 1/50,000sec

144x 95mm(H)

XD1000VA

OFF / x2 / x4 / x6 / x8 / x10 / x15 / x20 / x25 / x30

144

98

44

1.14 lb. (0.530kg)

1.44 lb. (0.650kg)

1.8

95

1/3"

2.8 - 12mm

2.8mm : 109˚

12mm : 37.8˚

Page is loading ...

Syscom Video XD1000VA User manual

Syscom Video XD1000VA User manual

Related papers

Other documents