Stairville Invader 2420 Owner's manual

Owner‘s Manual

DMX Controller

Invader 2420

Content

Notes on safety ..................................................................................................................................................................3

Maintenance and care .......................................................................................................................................................3

Introduction .......................................................................................................................................................................4

1. Features .........................................................................................................................................................................4

2. General Instructions .......................................................................................................................................................5

WARNINGS ...................................................................................................................................................................5

CAUTIONS ....................................................................................................................................................................5

3. Overview ........................................................................................................................................................................5

4. Operation Guide (Operating Steps Instructions) ............................................................................................................8

4.1 Programming Mode................................................................................................................................................8

4.2 Setting a scene .......................................................................................................................................................8

4.3 Program a Scene with Movement ..........................................................................................................................9

4.4 Program a Scene ...................................................................................................................................................10

4.5 Copy a Scene ........................................................................................................................................................11

4.6 Delete a Scene ......................................................................................................................................................12

4.7 Bank copying ........................................................................................................................................................12

4.8 Program a Chase ..................................................................................................................................................13

4.9 Program all the Scenes in a Bank ..........................................................................................................................14

4.10 Program a step ...................................................................................................................................................15

4.11 Insert Steps into a Chase ....................................................................................................................................16

4.12 Delete Steps from Program .................................................................................................................................18

4.13 Delete a CHASE ..................................................................................................................................................19

4.14 Program a Preset .................................................................................................................................................19

4.15 Preset Editing ......................................................................................................................................................20

4.16 Program a Fixture Group ....................................................................................................................................22

4.17 FIXTURE GROUP Editing .....................................................................................................................................23

4.18 Program a Centre ...............................................................................................................................................24

4.19 Centre Editing .....................................................................................................................................................25

4.20 Program an Override ..........................................................................................................................................26

4.21 Override Editing ..................................................................................................................................................27

4.22 Program a CUE ...................................................................................................................................................29

4.23 CUE Editing ........................................................................................................................................................29

4.24 Delete a CUE ......................................................................................................................................................30

4.25 Store a Blackout Scene .......................................................................................................................................31

5. Setting Menu ...............................................................................................................................................................31

5.1 Create a new Fixture Profile ..................................................................................................................................32

5.2 Modify a Fixture Profile .........................................................................................................................................34

5.3 Delete a Fixture Profile ..........................................................................................................................................35

5.4 Patch a Fixture ......................................................................................................................................................35

5.5 Reverse channel setup ..........................................................................................................................................36

5.6 Fade mode setup ..................................................................................................................................................37

5.7 Blackout mode select ...........................................................................................................................................38

5.8 Midi channel select ...............................................................................................................................................38

5.9 Chase run by inside/outside time .........................................................................................................................39

5.10 Auto remote address .........................................................................................................................................39

5.11 Read CF card ......................................................................................................................................................40

5.12 Write CF card ......................................................................................................................................................41

5.13 Modify Password ...............................................................................................................................................42

5.14 Enable Password .................................................................................................................................................43

5.15 Erase all memory ................................................................................................................................................43

5.16 Audio input range adjust ....................................................................................................................................44

5.17 Channel value display mode ...............................................................................................................................44

6. Function Mode ............................................................................................................................................................45

6.1 Running scene ......................................................................................................................................................45

6.2 Run Program ........................................................................................................................................................47

6.3 Running CUE ........................................................................................................................................................48

6.4 Over control ..........................................................................................................................................................49

7. Fog Machine operation ................................................................................................................................................49

8. Strobe light operation ..................................................................................................................................................50

9. MIDI function list ..........................................................................................................................................................51

10. Update the software with CF card.............................................................................................................................52

11. PROFILE Create notice ...............................................................................................................................................52

12. EC Declaration of Conformity ....................................................................................................................................55

13. Technical Specification ...............................................................................................................................................56

14. Disposal .....................................................................................................................................................................56

Notes on safety

For your own safety you should read through this chapter at rst completely!

Risk of electrical shocks!

Only connect the device to a properly wired and earthed mains power socket with mains voltage of 230 V ~ •

/50 Hz.

Do not operate the device if the power cord or the mains plug are damaged.•

Never submerse the device in water. Wipe it with a slightly moistened cloth only.•

Do not expose the device to rain and never use it in a damp or wet environment.•

Make sure that the power cord never becomes wet or moist during use.•

Under no circumstances may you open the device housing. Should you do so your safety would not be as-•

sured and the warranty will become void. There are no operational components whatsoever inside, only re-

ally high voltage that can give you a deadly shock!

Donotplaceobjectscontaininguids,e.g.owervasesorbeerbottles,onornearthedevice.•

Notice regarding disconnection from mains-power: •

To completely disconnect the device from mains power, you must pull the plug from the power socket. For

this reason the device should be placed in a position where unobstructed access to the power socket is as-

sured at all times, so that in an emergency you will be able to immediately pull out the plug. To eliminate the

riskofreyoushouldcompletelydisconnectthepowerplugfromthepowersocketwhenthedeviceisnot

going to be used for a long time, for example, during holidays.

Always grasp the power cord by the plug. Do not pull on the cord itself and never touch the power cord with •

wet hands as this could result in a short circuit or an electrical shock. Do not place the device, speakers or

anything else on the power cord and make sure that it does not become clamped. Never tie knots in the

power cord and do not bind it together with other cables. Lay the power cord so that no one can step on or

stumbleoverit.Adamagedpowercordcancauseareoranelectricalshock.Checkthepowercordfrom

time to time. Should it become damaged contact our customer service department to have it replaced.

Always operate the device only on a correctly earthed socket, never sever the power cord’s earth wire. Oth-•

erwise a LIFE THREATENING situation exists!

 Riskofre!

Never leave the device unattended during operation.•

Never cover the ventilation slots of the device while it is on. Do not place the device in locations that are •

subject to direct sunlight. If you do, it may overheat and become irreparably damaged.

Neveroperatetheamplierinthevicinityofheatsourcessuchascookers,heatingelementsorotherheat•

producing installations.

Donotplaceopenresources,suchascandles,onthedevice.•

Before a storm and/or a thunderstorm with a risk of lightning, please disconnect the device from the electri-•

cal power source.

Risk of personal injury!

Keepchildrenawayfromthepowercordandthedevice.Childrenfrequentlyunderestimatethedangersof•

electrical devices.

Provide a stable location for the device.•

Do not operate the device if it has sustained a fall or is damaged. Have the device checked or, •

ifnecessary,repairedbyqualiedtechnicians.

Maintenance and care

Neversubmersethedeviceinwateroranyotherliquid.Don‘tletanyliquidgetintothehousing.Thiswould•

damage the unit and cause a short circuit.

Beforecleaningthedeviceyoumustdisconnectitfromthemains.Cleanthesurfaceofthedeviceonlywith•

a slightly damp cloth. Never use petrol, solvents or any aggressive cleaners! These could damage the sur-

faceoftheunit‘shousing!

Introduction

ThankyouforpurchasingourInvader2420.Enjoyyournewequipmentandmakesuretoreadthismanual

carefully before operation!

1. Features

2 x DMX Outputs X

484 DMX Channels in total, including 481Ch. for DMX fog, 482Ch. for future use, 483-484Ch. for DMX X

strobe

Fixture Library ( for built-in ACME lighting xtures; Other brand xtures can be set manually but X

Max. with 50 xtures

Built-in 10 MOVEMENTS - Can adjust PAN/TILT Position PAN/TILT Range Fade time or Wait time X

LOOP

60 Programmable Chases, each chase can have 200 scenes max X

1200 Programmable Scenes (60 banks x 20 scenes) X

400 Programmable Presets (20 presets, each preset has 10 colours and 10 gobos) X

Control 20 DMX light xtures, and each xture up to 24 Channels X

Operate 20 Fixture groups simultaneously X

24 faders for controlling 24 DMX channels X

60 x CUEs (Combined many chases together and operate the chases at the same tine) X

20 x override – Can assign one (or more than one) of the xtures to perform special function, like X

follow spot, during the operation. 20 overrides can be set in the controller

20 x Centre - Can set each xture’s central position of the movement; you can set up to 20 centre X

positions

Remote DMX Addressing only for ACME lights X

Blackout mode - 1. Standby 2. PAN/TILT Centre Position 3.Blackout Scene X

Can use jog wheel to adjust the audio sensitivity (LCD display will indicate the value) X

Can set Password to boot the controller X

Lock/Unlock memory/Need password to clear all memory X

Standard MIDI facility X

Lighting Library and software downloaded available X

DMX fog machine control 481 Ch. X

Both DMX (483 & 484) and analog strobe control available (Via LCD display, people can adjust the X

speed of analog strobe)

2 remote Easy Controller ( CA-8 ) X

Gooseneck USB LAMP X

NOTE:SomebasicknowledgeofMIDIandDMXisrequiredtofullyutilizethisunit.

2. General Instructions

Please read the user manual carefully, as it includes important information regarding details of operation,

maintenance, and technical data. Keep this manual with the unit for future consult.

WARNINGS

DONOTmakeanyinammableliquids,waterormetalobjectsentertheunit.•

Shouldanyliquidbespilledontheunit,DISCONNECTthepowersupplytotheunitimmediately.•

STOP using the unit immediately In the event of serious operation problems and either contact your local •

dealer for a check or contact us directly.

DO NOT open the unit - there are no user serviceable parts inside.•

NEVERtrytorepairtheunityourself.Repairsbyunqualiedpeoplecouldcausedamageorfaultyopera-•

tion.Contactyournearestdealer.

CAUTIONS

This unit is NOT intended for home use.•

AfterhavingremovedthepackagingcheckthattheunitisNOTdamagedinanyway.Ifindoubt,DON‘Tuse•

it and contact an authorized dealer.

Packagingmaterial(plasticbags,polystyrenefoam,nails,etc.)MUSTNOTbeleftwithinchildren‘sreach,as•

it can be dangerous.

This unit must only be operated by adults. DO NOT allow children to tamper or play with it.•

NEVER use the unit under the following conditions: •

In places subject to excessive humidity.

In places subject to vibrations or bumps.

Inplaceswithatemperatureofover45°C/113°Forlessthan2°C/35.6°F.

Protect the unit from excessive dryness or humidity (ideal conditions are between 35% and 80%).•

DO NOT dismantle or modify the unit.•

3. Overview

3.1. Front View

1. FogMachineButton   ActivatesFogMachine.

2. STROBE Button Trigger strobe.

3. FixtureGroupButton   Select/setoneormorexturesgroup

4. FixtureButton   Selectoneormorextures

5. Preset Button Select/set the colour & gobo preset.

6. MovementButton   Select/setthepan&tiltmovement

7. ChaseButton    RunChaseandsaveScenetoChase

8. CueButton    SaveseveralChasestogetherandmakethemrunatthesame

time

9. Bank Button Press the Bank buttons to load or stored your scenes. There are a

     maximumof1200programmablescenes.

10. OverrideButton    Overridethexture/xtureswhentheshowisrunning.

11. CentreButton    Select/setthepan&tiltcentre.

12. Manual/RecButton   Usedtocontrolmanualoperationortorecordprograms.

13. ProgramButton    ActivatesProgrammode.

14. Music/BankCopyButton  ActivatesMusicmodeortocopyabankofscenes.

15. Tap/InsertButton   Usedtocreateastandardbeatorinsertascenetochase.

16. Auto/DelButton    ActivatesAutomodeortodeletescenesorchases.

17. Blackout/StandAloneButton SelectBlackout/StandAlonetwomodes.

18. USBLight    ConnecttoUSBLight

19. Faders     Thesefadersareusedtocontroltheintensity.

20. CFcard     CFcardportcanbeusedtoupgradesoftware,copydataand

introduce to light bank

21. Standalone    ExtraeasycontrollersIncorporatedforMaster/Slaveimmediate

pre-programmed light shows.

22. Multi-functionnumberbuttons1-20

Function buttons The descriptions of the Function buttons

1 Fixture Select 20 units of Fixtures Pls refer to the following

table for Fixture addresses

2 Fixture Group Set or select 20 Fixture Groups

3 Movement (only1-10)Selectoroperate10Movements

4 Preset 20groupsofxturescanbesetorselectedbyJog

wheelPAN.10colourPreset(1-10)and10GOBO

Preset(11-20)eachgroup

5 Cue Set,selectoroperate60Cues

6 Chase Set,selectoroperate60Chases

7 Override Set and select 20 Overrides

8 Bank 60banks(eachbankwith20scenes)canbesetand

selectedbyJogwheel#1

9 centre Set,selectandoperate20Centers

10 Number1-20button 1.1-10(10standfor0)Numberforsettingandinput-

ting password.

2.1-1010MOVEMENTcanbeselected.

3.1-10canbeusedtoselect10groupsofCOLOUR

PRESET;11-20canbeusedtoselectanother10

groups of GOBO PRESET.

4.1-20canbeusedtoselect20CUE/PAGECHASE/

PAGESCENE/BANKOVERRIDECENTREFIX-

TURE.

Fixture number channel list

Fixtures number buttons Fixture DMX channels Fixtures number buttons Fixture DMX channels

1 1-24 11 241-264

2 25-48 12 265-288

3 49-72 13 289-312

4 73-96 14 313-336

5 97-120 15 337-360

6 121-144 16 361-384

7 145-168 17 385-408

8 169-192 18 409-432

9 193-216 19 432-456

10 217-240 20 457-480

23. ESC/CLEARButton   Backtolastmenu/deletealltheoutputwhenprogram

24. Enter/mainmenuButton  Conrmorenternextmenuorentermainmenu

25. LCDDisplay    Showthecurrentactivityorprogrammingstate.

26. Jogwheel    Usedtoadjustthechasespeedwithintherangeof0.1secondto

5 minutes.

3.2 Rear View

1. Powerin     AC100-240V50/60Hz.

2. Power Switch This switch turns On/Off the power.

3. STROBE     Triggernon-DMXstrobe.Signal+12VDC.

4. AUDIO     0.1V~1Vp-p.

5. MIDI IN or MIDI THRU Receives MIDI data.

6. DMXOut     TwoconnectorssendsDMXsignalstoDMXxtures,use3pin

       XLRplugcabletolinkthexturetogether.

7. STAND ALONE The connectors are used only in master/slave mode, using 5 pin

       XLRcablemicrophonejackoftherstxture,youwillndthatthe

       remotecontrolontherstunitwillcontrolalltheotherunitsfor

Stand by, Function and Mode.

4. Operation Guide (Operating Steps Instructions)

Whenpoweristurnedon,thecontrollerstartsselftestingautomatically,theLCDDisplayindicatingtheself

testingprogress.Afteritisnished,thexturepilotontherearboardison,whichmeansthatyoucanstartto

operate the controller.

4.1 Programming Mode

Press PROGRAM button for 3 seconds, the LED above this button lights blinking

indicating Program in active.

4.2 Setting a scene

1. EnterProgrammode.

2. Pressthebutton1-20toselectFixture,youcanselectseveralxturesatatimeby

tapping of these buttons.

3. SlideFaders1-24orusetheCENTREorPRESETorSCENEhavesavedtochange

 theoutputofeachchannel.Youcanalsousethejogwheel#1&#2tocontrolthe

 PAN,PANFINEorusethejogwheel#3#4tocontrolTILT,TILTFINE.

4. Oncethesceneissatisfactory,pressMANUAL/RECbuttontoprogramthisscene

 intomemory.Atthismoment,theLEDsonCUE,OVERRIDE,CENTRE,FIXTURE

 GROUP,PRESET,CHASE,BANK,BLACKOUTbuttonblinkatthesametime.

5. PressBANKusetheJogwheel#1toselecttheBANKnumbertosavethescene.

6. Pressthenumberbutton1-20toselecttheScenenumbergoingtobesaved,all

 LEDsandtheSegmentDisplaywillblinkthreetimesbrieyindicatingthisoperation,

 thentheLCDwillshowthebankandthescenenumberoftheprogrammedscene.

7. Repeatsteps2-6toprogramotherscenes.

8. Press PROGRAM button for 3 seconds to exit Program mode, the LED goes out

indicating this selection.

4.3 Program a Scene with Movement

1. EnterProgrammode.

2. Pressthebutton1-20toselectFixture,youcanselectseveralxturesatatimeby

tapping of these buttons.

3.MoveFaders1-24orusetheCENTRE,PRESET,SCENEhavesavedtochangethe

output of each channel, press MOVEMENT button.

4. Pressthebutton1-10toselectoneMOVEMENTinten,theselectedFIXTUREwill

run the MOVEMENT.

5. IfitisnecessarytoadjustMOVEMENTparameter,useJogwheel#2toselectthe

adjusting MOVEMENT parameter options (position & range & fade time or wait time

 &loop),useJogwheel#3,#4toadjustparametervalues.

6. RepeatSteps2–5toselectMOVEMENTforotherFIXTURE.

7. PressMANUAL/RECtostoreintomemory,alltheLEDsonCUE,OVERRIDE,

 CENTRE,FIXTUREGROUP,PRESET,CHASE,BANK,BLACKOUTblinkto

indicate this operation.

8. PressBANKuseJogwheel#1toselecttheBANKnumbertostorethescene.

9. Pressthenumberbutton1-20toselecttheScenenumbergoingtobesaved,all

 LEDsandtheSegmentDisplaywillblinkforthreetimesbrieyindicatingthis

 operation,thentheLCDwillshowthebankandthescenenumberofthe

programmed scene.

10.Repeatsteps2-9toprogramotherSCENEswithMOVEMENT.

11.Ifyoudon‘tintendtocontinueyourprogramming,pressandholddownthe

PROGRAM button for three seconds to exit Program mode, the LED goes out

indicating this selection.

4.4 Program a Scene

1. EnterProgrammode.

2. Press the button BANK, to turn on its fader control, which is indicated by the lit LED,

 useJogwheel#1toselectthebanknumbertoeditthescene.

3. Pressthenumberbutton1-20toopenthesceneyouaregoingtoedit.

4. MoveFaders1-24orusetheCENTRE,PRESET,SCENEhavesavedtochange

 theoutputofeachchannel,youcanalsousetheJogwheel#1,#2toadjustPAN,

 PANFINE,oruseJogwheel#3,#4toadjustTILT,TILTFINEorpressMOVEMENT

to add MOVEMENT function.

5. PressMANUAL/RECtostore,LEDsonCUE,OVERRIDE,CENTRE,FIXTURE

 GROUP,PRESET,CHASE,BANK,BLACKOUTblinkatthesametime.

6. PressthebuttonBANK.

7. Pressthenumberbutton1-20tostoretheeditedscenewhichwillcovertheformer

 scenes,allLEDsandtheSegmentDisplaywillblinkforthreetimesbrieyindicating

 thisoperation,thentheLCDwillshowthebankandthescenenumberofthe

programmed scene.

8. Press the button PROGRAM for three second, to exit Program mode, the LED goes

out indicating this selection.

Hint:Ifyouselectdifferentscenesatstep3and6,theeditingscenewouldcoverthesceneatstep6.

4.5 Copy a Scene

1. EnterProgrammode.

2. Press the button BANK, to turn on its fader control, which is indicated by the lit LED.

 UseJogwheel#1toselectthebanknumbertoeditthescene.

3. Pressthenumberbutton1-20toopenthesceneyouaregoingtocopy.

4. PressMANUAL/RECtostore,LEDsonCUE,OVERRIDE,CENTRE,FIXTURE

 GROUP,PRESET,CHASE,BANK,BLACKOUTblinkatthesametime.

5. PressBANKThenusetheJogwheel#1toselecttheBANKnumbertocopythe

scene.

6. Pressthenumberbutton1-20,thencopytheScenetotherightposition.AllLEDs

 andtheSegmentDisplaywillblinkforthreetimesbrieyindicatingthisoperation,

 thentheLCDwillshowthebankandthescenenumberoftheprogrammedscene.

7. Ifyoudon‘tintendtocontinueyourprogramming,pressandholddownthe

PROGRAM button for three seconds to exit Program mode, the LED goes out

indicating this selection.

4.6 Delete a Scene

1. EnterProgrammode.

2. UsetheJogwheel#1toselecttheBanknumberofthebeingdeletedscene.

3. Pressthenumberbutton1-20toselectthesceneyouaregoingtodelete.

4. Press the button AUTO/DEL.

5. Press the button BANK.

6. Thenpressthenumberbutton1-20,thescenewillbedeleted,allLEDsandthe

 SegmentDisplaywillblinkforthreetimesbrieyindicatingthisoperation,thenthe

 LCDwillshowthebankandthescenenumberofthedeletedscene.

7. Ifyoudon‘tintendtocontinueyourprogramming,pressandholddownthe

PROGRAM button for three seconds to exit Program mode, the LED goes out

indicating this selection

4.7 Bank copying

1. EnterProgrammode.

2. Press BANK button

3. UsetheJogwheel#1toselecttheBanknumberofthebeingcopiedscene.

4. PressthebuttonMANUAL/REC,LEDsonCUE,OVERRIDE,CENTRE,FIXTURE

 GROUP,PRESET,CHASE,BANK,BLACKOUTblinkatthesametime.

5. ThenturntheJogwheel#1toselectthebanknumbertocopyto.

6. PressthebuttonMUSIC/BANKCOPY,allLEDsandtheSegmentDisplaywillblink

 forthreetimesbrieyindicatingthisoperation,thentheLCDwillshowthenumberof

the being copied bank and the bank is being copied to and the scene number of the

programmed scene.

7. Press the button PROGRAM for three seconds to exit Program mode, the LED goes

out indicating this selection

4.8 Program a Chase

Note: The chase should be programmed after the scene is set. Each chase can have 200 scenes max.

1. EnterProgrammode.

2. PressthebuttonCHASE,LEDsonCHASEwillbealllit.Usejogwheel#1toselect

the page number of the chase.

3. Pressthenumberbutton1-20toselectthechasenumber,theLEDsonBANK

 buttonwillbealllit,theLCDwillshowthenumberandparameterofCHASE,BANK,

 SCENE,STEP,FADE,WAIT.

4. UsetheJogwheel#1totransfertootherBanks,thenpressthenumberbutton1-20

toselectthescenetostoretheChase.

5. UsetheJogwheel#3toadjusttheFADETIMEofpresentchase,theJogwheel#4

to adjust the WAIT TIME of the present chase. If you do not make any adjustments,

the system will remember the last FADE TIME or WAIT TIME.

6. PressthebuttonMANUAL/REC,alltheLEDswillblinkforthreetimesbriey

indicating the store succeed.

7. RepeatStep4-6,eachchasecanhave200scenesmax.

8. Press the button PROGRAM for three seconds to exit Program mode, the LED goes

out indicating this selection.

4.9 Program all the Scenes in a Bank

1. EnterProgrammode.

2. PressthebuttonCHASEusejogwheel#1toselectthepagenumber,choosethe

programming chase.

3. Pressthenumberbutton1-20toselecttheChasenumber,LEDsontheBANK

 buttonwillbealllit,theLCDwillshowthenumberandparameteroftheCHASE,

 BANK,SCENE,STEP,FADE,WAIT.

4. UsetheJogwheel#1toselecttheBanknumberoftheprogrammedChase.

5. UsetheJogwheel#3,#4toadjusttheFADETIMEandWAITTIMEwhicharegoing

 tobeaddedtothesingleChase.Ifyoudonotmakeanyadjustments,thesystem

will remember the last FADE TIME or WAIT TIME.

6. PressthebuttonMUSIC/BANKCOPY

7. PressthebuttonMANUAL/REC,allLEDsblinkfor3times,alltheprogrammed

 scenesintheBankwilljointheChase.

8. Repeat Step 3-7 can join 200 scenes max to the chase.

9. FinallypressthebuttonCHASEtostorethechasethenexittheprogrammingstate.

10.PressthebuttonPROGRAMforthreesecondstoexitProgrammode,theLEDgoes

out indicating this selection.

4.10 Program a step

1. EnterProgrammode.

2. PressthebuttonCHASEusejogwheel#1toselectthepagenumberofthechase

to select the program.

3. Pressthenumberbutton1-20toselecttheChasenumber,LEDsontheBANK

 buttonwillbealllit,theLCDwillshowthenumberandparameteroftheCHASE,

 BANK,SCENE,STEP,FADE,WAIT.

4. UseJogwheel#2toviewthesteps,thestrobedisplay[002]indicateprogrammable

step number.

5. Usejogwheel#1toselectthebanknumberofthescene,pressnumberbutton1-20

to open.

6. UsetheJogwheel#3,#4toadjusttheFADETIMEandWAITTIMEwhicharegoing

 tobeaddedtothesingleChase.Ifyoudonotmakeanyadjustments,thesystem

will remember the last FADE TIME or WAIT TIME.

7. PressthebuttonMANUAL/RECallLEDsblinkfor3timestoindicatethatyouhave

successfully programmed a step.

8. Repeat steps 2-3 to select other steps.

9. PressthebuttonCHASEtostoreandexittheprogrammingstate.

10.PressthebuttonPROGRAMfor3secondstoexitProgrammode,theLEDgoesout

indicating this operation.

4.11 Insert Steps into a Chase

1. EnterProgrammode.

2. PressthebuttonCHASEusejogwheel#1toselectthepagenumber,choosethe

programming chase.

3. Pressthebutton1-20toselectthechasenumber.

4. UsetheJogwheel#2toselectthepositionofinsertedsteps.

5. Press the button TAP/INSERT to insert a step following the present position.

6. UsetheJogwheel#1toselecttheBanknumberoftheinsertedscene.

7. Pressthenumberbutton1-20toselectthescenetobeinserted.

8. UsetheJogwheel#3,#4toadjusttheCHASEFADETIMEandWAITTIME.Ifyou

do not make any adjustments, the system will remember the last FADE TIME or

WAIT TIME.

9. PressthebuttonMANUAL/RECallLEDsblinkfor3timestoindicatethatyouhave

successfully inserted a step into a chase.

10.Repeatsteps5-9,youcaninsert200scenestoeachchase.

11.PressthebuttonCHASEtostorethechaseandexitthechaseprogrammingstate.

12.PressthebuttonPROGRAMfor3secondstoexitProgrammode,theLEDgoesout

indicating this operation.

4.12 Delete Steps from Program

1. EnterProgrammode.

2. PressthebuttonCHASEusejogwheel#1toselectthepagenumber,choosethe

programming chase.

3. Pressthenumberbutton1-20toselectthechasenumbertodeletefrom.

4. UseJogwheel#2toselectthescenelocationyouwanttodelete.

5. Press AUTO/DEL all LEDs blink for 3 times to indicate that you have successfully

deleted the scene.

6. Repeatsteps4-5todeletemorescenesfromthechase.

7. PressthebuttonCHASEtostoretheoperationandexitfromthepresent

programming state.

8. Press the button PROGRAM for 3 seconds to exit Program mode, the LED goes out

indicating this operation.

4.13 Delete a CHASE

1. EnterProgrammode.

2. PressthebuttonCHASE,usejogwheel#1toselectthepagenumber,choosethe

programming chase.

3. Press the button AUTO/DEL.

4. Pressthenumberbutton1-20toselectthechasetobedeleted,allLEDsblinkfor3

times to indicate that you have successfully delete the chase.

5. Repeat the steps 2-4 to delete more chases.

6. PressthebuttonPROGRAMfor3secondstoexitProgrammode,theLEDgoesout

indicating this operation.

4.14 Program a Preset

1. EnterProgrammode.

2. Press the button FIXTURE

3. Pressthebutton1-20toselecttheconcernedxtureofpresetprogramming.

4. MovetheFADERS1-24tochangeCOLOUR/GOBOchannelvalues(Thecodesofthe

 channelfeatureofARRTCODEare“C”and“G”inthexturesbank)outputforthe

convenience to check other channels but the channel output will not be stored in the

preset.

5. PressthebuttonMANUAL/RECatthismomentallLEDsonbuttonsCUE,

 OVERRIDE,CENTRE,FIXTUREGROUP,PRESET,CHASE,BANK,BLACKOUT

blink at the same time.

6. PressthebuttonPRESET.

7. UseJogwheel#1toselectthepresetgroupnumber1-20.

8. Pressoneofthenumberbutton1-10tostoreaCOLOURpresetorpressoneofthe

 numberbutton11-20tostoreaGOBOpreset,allLEDsblinkfor3timestoindicate

that you have successfully store a Preset.

9. Repeat Steps 2-8 to program more presets.

10.PressthebuttonPROGRAMfor3secondstoexitProgrammode,theLEDgoesout

indicating this operation.

4.15 Preset Editing

1. EnterProgrammode.

2. Press PRESET Button to select programming Preset state.

Page is loading ...

Stairville Invader 2420 Owner's manual

Related papers

Other documents