ADJ SAB605 Saber Spot WW Compact Pinspot Light User manual

User Instructions

09/20

specications, diagrams, images, and instructions herein are

subject to change without notice. ADJ Products, LLC logo and

identifying product names and numbers herein are trademarks

of ADJ Products, LLC. Copyright protection claimed includes all

forms and matters of copyrightable materials and information

now allowed by statutory or judicial law or hereinafter granted.

Product names used in this document may be trademarks or

registered trademarks of their respective companies and are

hereby acknowledged. All non-ADJ Products, LLC brands and

product names are trademarks or registered trademarks of their

respective companies.

ADJ Products, LLC and all aliated companies hereby dis-

claim any and all liabilities for property, equipment, building,

and electrical damages, injuries to any persons, and direct or

indirect economic loss associated with the use or reliance of

any information contained within this document, and/or as a

result of the improper, unsafe, unsucient and negligent as-

sembly, installation, rigging, and operation of this product.

Europe Energy Saving Notice

Energy Saving Matters (EuP 2009/125/EC)

Saving electric energy is a key to help protecting the enviroment.

Please turn o all electrical products when they are not in use. To

avoid power consumption in idle mode, disconnect all electrical

equipment from power when not in use. Thank you!

SABER SPOT WW

401076 5

ADJ Products, LLC - www.adj.com - Saber Spot WW Instruction Manual Page 3ADJ Products, LLC - www.adj.com - Saber Spot WW Instruction Manual Page 2

• DMX-512 Protocol Compatible (3 DMX Channel Modes: 1/2/4

• 3 Operating Modes - Show Mode, WW Dimmer Mode & DMX

Control

• 5 Dimmer Curves (Standard, Stage, TV, Architectural, & Theatre)

• Digital Display for Address and Function Setting

• UC IR Compatible (Not Included) & Airstream App Compatible

• Power Cord Daisy Chainable (See page 23)

Saber Spot WW Features

Caution! There are no user serviceable parts inside this unit. Do not

attempt any repairs yourself, doing so will void your manufactures

warranty. In the unlikely event your unit may require service please

contact ADJ Products, LLC.

During operation the housing may become extremely hot. Avoid

touching the unit with bare hands while in use.

ADJ Products, LLC will not accept any liability for any resulting dam-

ages caused by the non-observance of this manual or any unauthor-

ized modication to this unit.

Saber Spot WW Handling Precautions

Saber Spot WW Warranty Registration

The Saber Spot WW carries a 2 year (730 days) limited warranty.

Please fill out the enclosed warranty card to validate your purchase

and warranty. You may also register your product online at www. adj-

products.com. All returned service items whether under warranty or

not, must be freight pre-paid and accompany a return authorization

(R.A.) number. If the unit is under warranty you must provide a copy

of your proof of purchase invoice. Please contact ADJ Products, LLC

customer support for a R.A. number.

To optimize the performance of this product, please read these

operating instructions carefully to familiarize yourself with the basic

operations of this unit. These instructions contain important safety

information regarding the use and maintenance of this unit. Please

keep this manual with the unit, for future reference.

Saber Spot WW General Instructions

Saber Spot WW General Information

Unpacking: Thank you for purchasing the Saber Spot WW by ADJ

Products, LLC. Every Saber Spot WW has been thoroughly tested and

has been shipped in perfect operating condition. Carefully check the

shipping carton for damage that may have occurred during shipping.

If the carton appears to be damaged, carefully inspect your xture for

any damage and be sure all equipment necessary to operate the unit

has arrived intact. In the event damage has been found or parts are

missing, please contact our toll free customer support number for fur-

ther instructions. Please do not return this unit to your dealer without

contacting customer support rst.

Introduction: The Saber Spot WW is a DMX intelligent LED fix-

ture. The Saber Spot WW can operate as a stand alone fixture or in a

primary/secondary set up. The Saber Spot WW has three operating

modes; WW dimmer mode, show mode, & DMX controlled. This fixture

is suit-able for theaters, studios, retail stores, and other similar

locations. For best results use fog or special effects smoke to

enhance the beams projections.

Customer Support: ADJ Products, LLC provides a toll free cus-

tomer support line, to provide help and to answer any question should

you encounter problems during your set up or initial operation. You

may also visit us on the web at www.adj.com for any comments or

suggestions. Service Hours are Monday through Friday 8:00 a.m. to

4:30 p.m. Pacic Standard Time.

Voice: (800) 322-6337

Fax: (323) 582-2941

E-mail: support@americandj.com

Warning! To prevent or reduce the risk of electrical shock or re, do

not expose this unit to rain or moisture.

Warning! This may cause severe eye damage. Avoid looking directly

into the light source at all times!

For Your Own Personal Safety, Please Read and Understand This

Manual Completely Before You Attempt To Install Or Operate

This Unit!

• To reduce the risk of electrical shock or re, do not expose this unit

rain or moisture

• Do not spill water or other liquids into or on to your unit.

• Be sure that the local power outlet match that of the required volt-

age for your unit.

• Do not attempt to operate this unit if the power cord has been

frayed or broken.

• Do not attempt to remove or break o the ground prong from

the electrical cord. This prong is used to reduce the risk of electrical

shock and re in case of an internal short.

• Disconnect from main power before making any type of connection.

• Do not remove the cover under any conditions. There are no user

serviceable parts inside.

• Never operate this unit when it’s cover is removed.

• Always be sure to mount this unit in an area that will allow proper

ventilation. Allow about 6” (15cm) between this device and a wall.

• Do not attempt to operate this unit, if it becomes damaged.

• This unit is intended for indoor use only, use of this product out-

doors voids all warranties.

• Always mount this unit in safe and stable matter.

• Power-supply cords should be routed so that they are not likely to

be walked on or pinched by items placed upon or against them,

paying particular attention to cords at plugs, convenience recep-

tacles, and the point where they exit from the appliance.

• Cleaning -The fixture should be cleaned only as recommended by

the manufacturer. See page 21 for cleaning details.

• Heat -This fixture should be situated away from heat sources such

as radiators, heat registers, stoves, or other appliances (including

amplifiers) that produce heat.

• The fixture should be serviced by qualified service personnel when:

A. Objects have fallen, or liquid has been spilled into the appliance.

B. The appliance has been exposed to rain or water.

C. The appliance does not appear to operate normally or exhibits

a marked change in performance.

Saber Spot WW Safety Precautions

ADJ Products, LLC - www.adj.com - Saber Spot WW Instruction Manual Page 5ADJ Products, LLC - www.adj.com - Saber Spot WW Instruction Manual Page 4

Power Supply: The ADJ Saber Spot WW contains a automatic volt-

age switch, which will auto sense the voltage when it is plugged into

the power source. With this switch there is no need to worry about

the correct power voltage, this unit can be plugged in anywhere.

DMX-512: DMX is short for Digital Multiplex. This is a universal pro-

tocol used by most lighting and controller manufactures as a form

of communication between intelligent fixtures and controllers. A

DMX controller sends DMX data instructions from the controller to

the fix-ture. DMX data is sent as serial data that travels from fixture to

fixture via the DATA “IN” and DATA “OUT” XLR terminals located on

all DMX fixtures (most controllers only have a DATA “OUT” terminal).

DMX Linking: DMX is a language allowing all makes and models

of different manufactures to be linked together and operate from

a single controller, as long as all fixtures and the controller are

DMX compliant. To ensure proper DMX data transmission, when

using several DMX fixtures try to use the shortest cable path

possible. The order in which fixtures are connected in a DMX line

does not influence the DMX addressing. For example; a fixture

assigned a DMX address of 1 may be placed anywhere in a DMX

line, at the beginning, at the end, or anywhere in the middle.

Therefore, the first fixture controlled by the controller could be the

last fixture in the chain. When a fixture is assigned a DMX address

of 1, the DMX controller knows to send DATA assigned to address

1 to that unit, no matter where it is located in the DMX chain.

Data Cable (DMX Cable) Requirements: The Saber Spot WW can

be controlled via DMX-512 protocol. The Saber Spot WW has 3

DMX channel modes. The DMX

address is set electronically using the controls on

the rear panel of the unit. Your unit and your DMX

controller require a approved DMX-512 110 Ohm

Data cable for data input and data output (Figure

1). We recommend Accu-Cable DMX cables. If you

are making your own cables, be sure to use stan-

dard 110-120 Ohm shielded cable (This cable may

be purchased at almost all professional sound and

lighting stores). Your cables should be made with

Saber Spot WW DMX Set Up

Figure 1

ADJ Products, LLC - www.adj.com - Saber Spot WW Instruction Manual Page 6 ADJ Products, LLC - www.adj.com - Saber Spot WW Instruction Manual Page 7

5-Pin XLR DMX Connectors.

Some manufactures use 5-pin DMX-

512 data cables for DATA transmission in place of 3-pin. 5-pin DMX

xtures may be implemented in a 3-pin DMX line. When inserting stan-

dard 5-pin data cables in to a 3-pin line a cable adaptor must be used,

these adaptors are readily available at most electric stores. The chart

below details a proper cable conversion.

Conductor 5-Pin XLR Male (In)3-Pin XLR Female (Out)

Pin 1

Pin 5 - Do Not Use

Pin 4 - Do Not Use

Pin 3

Pin 2

Pin 1

Pin 3

Pin 2

Not Used

Data True (+ signal)

Data Compliment (- signal)

Ground/Shield

3-Pin XLR to 5-Pin XLR Conversion

Saber Spot WW DMX Set Up

a male and female XLR connector on either end of the cable. Also

remember that DMX cable must be daisy chained and cannot be split.

Saber Spot WW DMX Set Up

Notice: Be sure to follow gures two and three when making your own

cables. Do not use the ground lug on the XLR connector. Do not con-

nect the cable’s shield conductor to the ground lug or allow the shield

conductor to come in contact with the XLR’s outer casing. Grounding

the shield could cause a short circuit and erratic behavior.

DMX512 IN

3-PIN XLR

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

DMX512

DMX+,DMX-,COMMON

1

2

3

Termination reduces signal errors and

avoids signal transmission problems

and interference. It is always advisable

to connect a DMX terminal, (Resistance

120 Ohm 1/4 W) between PIN 2 (DMX-)

and PIN 3 (DMX +) of the last fixture.

1

2

3

1

2

3

DMX +

DMX -

COMMON

DMX512 OT

3-PIN XLR

Figure 2

Figure 3

1 Ground 1 Ground

XLR Male Socket XLR Pin Conguration

3 Hot

2 Cold 2 Cold

3 Hot

XLR Female Socket

Pin 3 = Data True (positive)

Pin 2 = Data Compliment (negative)

Pin 1 = Ground

Special Note: Line Termination.

When longer runs of cable are

used, you may need to use a terminator on the last unit to avoid erratic

behavior. A terminator is a 110-120 ohm 1/4 watt resistor which is con-

nected between pins 2 and 3 of a male XLR connector (DATA + and

DATA -). This unit is inserted in the female XLR connector of the last

unit in your daisy chain to terminate the line. Using a cable terminator

(ADJ part number Z-DMX/T) will decrease the possibilities of erratic

behavior.

DMX512 IN

3-PIN XLR

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

DMX512

DMX+,DMX-,COMMON

1

2

3

Termination reduces signal errors and

avoids signal transmission problems

and interference. It is always advisable

to connect a DMX terminal, (Resistance

120 Ohm 1/4 W) between PIN 2 (DMX-)

and PIN 3 (DMX +) of the last fixture.

1

2

3

1

2

3

DMX +

DMX -

COMMON

DMX512 OT

3-PIN XLR

Figure 4

ADJ Products, LLC - www.adj.com - Saber Spot WW Instruction Manual Page 9ADJ Products, LLC - www.adj.com - Saber Spot WW Instruction Manual Page 8

Saber Spot WW System Menu

System Menu: When making adjustments press ENTER to

conrm your setup then press and hold the MENU button

for at least 3 seconds. To exit without making any adjust-

ments press the MENU button. The display will lock after 30

seconds, press the MENU button for 3 seconds to unlock.

DMX MODE - DMX Address Setting.

1. Press the either the MENU, UP, or DOWN buttons until “DMX

MODE” is displayed, press ENTER.

2. The current address will now be displayed and ashing.

Press the UP or DOWN buttons to nd your desired address.

Press ENTER to set your desired DMX address.

CHANNEL - This will let select your desired DMX

channel mode.

1. Press the either the MENU button until “CHANNEL” is dis-

played, press ENTER. The current DMX channel mode will be

displayed.

2. Press the UP or DOWN buttons to nd your desired DMX

channel mode and press ENTER to conrm and exit.

SECONDARY - This will let you set the unit as the

secondary in a primary/secondary configuration.

1. Press the MENU button until “SECONDARY” is

displayed, press ENTER.

LOOK - In this mode you can run a show mode.

1. Press the MENU button until “LOOK” is displayed, press

ENTER.

2. Use the UP or DOWN buttons to nd your desired mode.

Saber Spot WW System Menu

Software Update

Please Wait ...

ADJ

SOFTWARE V1.0 3

About LED protection

When reach 65 degree, the power consumption is reduced to 82%. When the sensor is

damaged, the power consumption is reduced to 65%.

SN MENU DISPLAY FUNCTION

1 DMX MODE

ADDR 001

Address setting

001- 512

2 CHANNNEL 4CH 1/2/4CH(see channel mode)

3 Secondry Secondary mode

4 LOOK

Store:01 Store mode01- 13

5 Reset

NO

Yes,press ENTER to resume the factory

default setting

6 Manual

W 000- 255 S 000- 255

Manual dimmer

W 000- 255 strobe S000- 255

7 DimCurve

Standard

5 kinds Dimmer curve

Standard, Stage, TV, Architec,

Theatre

8NO DMX No DMX mode

Hold Blackout, Hold, LOOK

9 TempUnit C/F

10 Temp Val Temperature show: xxx F

11 AUTOLOCK Display keylock OFF/ON

12 IR Active IR setting OFF/ON

13 FlipDisplay Flip display OFF/ON

Display Menu

Special Remark:

ADJ Products, LLC - www.adj.com - Saber Spot WW Instruction Manual Page 10 ADJ Products, LLC - www.adj.com - Saber Spot WW Instruction Manual Page 11

2. Press the UP or DOWN buttons to nd your desired dimmer

curve and press ENTER to conm.

NO DMX - This mode can be used as a precaution mode,

that in case the DMX signal is lost, interrupted, or power is

lost, the operating mode chosen in the setup is the running

mode the xture will go into when the DMX signal is lost. You

can also set this as the operating mode you would like the

unit to return to when power is applied.

1. Press the MENU button until “NO DMX” is displayed, and

either “Look”, “Blackout”, or “Hold” will be displayed beneath.

2. Press ENTER and the bottom choice will begin to ash. Use

the UP or DOWN buttons to choose an operating mode you

would like the unit to start up in when power is applied or the

DMX signal is lost.

•Look (Primary/Secondary) - If the DMX signal is lost or

power is applied, the unit will automatically run a built-in show.

•Blackout - If the DMX signal is lost or interrupted, the unit will

automatically go into stand by mode.

•Hold - If the DMX signal is lost the fixture will stay in the last

DMX setting. If power is applied and this mode is set, the unit will

automatically go into the last DMX set up.

3. Press ENTER to conrm your desired set up.

TempUnit - With this function you can switch the tem-

perature display to show either Celsius or Fahrenheit.

1. Press the MENU button until “TempUnit” is displayed, press

ENTER.

2. Use the UP or DOWN buttons to switch between Celsius or

Fahrenheit. Press ENTER to select your desired setting.

Saber Spot WW System Menu

RESET - This function will return the unit to its default

settings.

1. Press the the MENU button until “RESET” is displayed and

press ENTER.

2. The display will show either “NO” or “YES”. Press the UP or

DOWN buttons so that “YES” is displayed. Press ENTER and

the unit will reset back to default settings.

MANUAL - This function will allow you to manually

adjust each LED output intensity and strobe rate. This func-

tion is also a manual testing mode.

1. Press the MENU button until “MANUAL” is displayed, press

ENTER.

2. Using the UP or DOWN buttons scroll to the Strobe setting

and press ENTER. Use the UP or DOWN buttons to set the

strobe setting to “255”, and press ENTER again

3. After you have set the strobe setting to “255”, press the

UP or DOWN buttons so that W:XXX is displayed and press

ENTER. Now use the UP or DOWN buttons to adjust the output

intensity.

4. If you would like the unit to strobe, scroll back to the strobe

setting and press ENTER. Use the UP or DOWN buttons to

adjust the strobe rate. Press ENTER once you have found your

desired strobe rate.

DimCurve - This will let select your desired dimmer

curve.

1. Press the MENU button until “DimCurve” is displayed, and

press ENTER. 1 of 5 dimmer curves will be displayed. “STAN-

DARD”, “STAGE”, “TV”, “ARCHITEC” (Architectural), or “THE-

ATRE”. See the dimmer curve chart on page 199 for more info.

Saber Spot WW System Menu

ADJ Products, LLC - www.adj.com - Saber Spot WW Instruction Manual Page 12 ADJ Products, LLC - www.adj.com - Saber Spot WW Instruction Manual Page 13

Temp Val - With this function you can check the tem-

perature of the xture.

1. Press the MENU button until “Temp Val” is displayed, press

ENTER.

2. The xture temperature will now be displayed. Press MENU

to exit.

AUTOLOCK - With this function you can have the

keys lock off after 10 seconds of no use.

1. Press the MENU button until “AUTOLOCK” is displayed,

press ENTER.

2. The display will show either “ON” or “OFF”. Press the UP or

DOWN buttons to select “ON” to have the keys lock after 10

seconds, or “OFF” so that the keys will remain unlocked.

3. Press ENTER to conrm.

IR Active - With this function you can activate the IR

function and use the UC IR or Airstream app to control the

unit.

1. Press the MENU button until “IR Active” is displayed, press

ENTER.

2. The display will show either “ON” or “OFF”. Press the UP or

DOWN buttons to select “ON” to activate IR function, or “OFF”

to turn o the IR function.

3. Press ENTER to conrm. See page 16 for IR controls.

FlipDisplay - This function will reverse the display

180º.

1. Press the either the MENU button until “FlipDisplay” is dis-

Saber Spot WW System Menu

played, press ENTER.

2. The display will show either “ON” or “OFF”. Press the UP or

DOWN buttons to select “ON” to ip the display, or “OFF” to

keep the display normal.

3. Press ENTER to conrm.

Saber Spot WW System Menu

ADJ Products, LLC - www.adj.com - Saber Spot WW Instruction Manual Page 15ADJ Products, LLC - www.adj.com - Saber Spot WW Instruction Manual Page 14

Universal DMX Control: This function allows you to use a uni-

versal DMX-512 controller to control the colors, master dimmer and

strobe. A DMX controller allows you to create unique programs tai-

lored to your individual needs.

1. The Saber Spot WW has 3 DMX channel modes. See pages

17-18 for detailed description of the DMX values and traits.

2. To control your fixture in DMX mode, follow the set-up procedures

on pages 7-9 as well as the set-up specifications that are includ-

ed with your DMX controller.

3. Use the controller’s faders to control the various DMX fixture traits.

4. This will allow you to create your own programs.

5. Follow the instruction on page 9 to select your DMX channel

mode and set your desired DMX address.

6. For longer cable runs (more than a 100 feet) use a terminator on

the last fixture.

7. For help operating in DMX mode consult the manual included

with your DMX controller.

Show Mode: This mode allows either a single unit or several units

linked together to run a built-in program.

1. Press the MENU button until “Look” is displayed, and press

ENTER.

2. Press the UP or DOWN buttons to nd your desired show.

Saber Spot WW Operation Saber Spot WW Primary-Secondary Set Up

Primary-Secondary Operation This function will allow you to

link up to 16 units together and operate without a controller. In a

Primary-Secondary set up, one unit will act as the controlling unit and

the others will react to the controlling units programs. Any unit can

act as a Primary or as a Secondary.

1. Using approved DMX data cables, daisy chain your units togeth-

er via the XLR connector on the rear of the units. Remember the

Male XLR connector is the input and the Female XLR connector

is the output. The first unit in the chain (primary) will use the

female XLR connector only - The last unit in the chain will use the

male XLR connector only. For longer cable runs we suggest a

terminator at the last fixture.

2. On the Primary unit find your desired operating mode.

3. On the Secondary units press the MENU button until

“Secondary” is displayed.

4. The Secondary units will now follow the Primary unit.

Saber Spot WW Installing the Frost Lens

The Saber Spot WW Plus comes with 2 frost filters. Install the filter in

front of the lens and put the inlcuded retainer ring top to hold the lens

in place.

ADJ Products, LLC - www.adj.com - Saber Spot WW Instruction Manual Page 16 ADJ Products, LLC - www.adj.com - Saber Spot WW Instruction Manual Page 17

The UC IR (sold separately) infrared remote gives you control of

various functions (See below). To control the fixture you must aim the

remote at the front of the fixture and be no more than 30 feet away.

The Saber Spot WW is also compatible with the Airstream IR app.

The IR transmitter is available through any ADJ dealer or through the

ADJ parts website. Plug the transmitter into the headphone jack of

your iOS phone or tablet. To control your IR fixture you must raise

the volume to the maximum on your iOS phone or tablet and aim

the transmitter at the front of the fixture and be no more than 15

feet away. After you have purchased the Airstream IR transmitters,

the app is a free download from the app store for your iOS phone or

tablet. The app comes with 3 pages of control depending on the IR

fixture you are using. Please see below for IR functions including the

corresponding app page.

Works with App page 1.

STAND BY - Press this button to go into DMX mode or IR active.

FULL ON - Press this button down to fully light up the unit.

STROBE - Press this button to activate strobing. Use the “Dimmer

+/- to adjust the strobe rate.

FADE/GOBO - Press this button to activate fade mode. Continue to

press this button to find your desired fade speed.

“DIMMER +” and “DIMMER -” - Use these buttons adjust the strobe

rate and output intensity in color mode.

COLOR - This button is will activate the warm white color. You must

first press Full On then press Color twice until it blacksout. Then you

can use the Dimmer +/- to adjust the output intensity.

1-9 - These buttons are invalid for this fixture.

SOUND ON & OFF - These buttons are invalid for this fixture.

SHOW 0 - This button is invalid for this fixture.

Saber Spot WW UC IR Operation

Channel Value Function

1 WARM WHITE

0 - 255 0% - 100%

Saber Spot WW 1 Channel Mode

Channel Value Function

1 WARM WHITE

0 - 255 0% - 100%

2 SHUTTER/STROBE

0 - 31 LED OFF

32 - 63 LED ON

64 - 95 STROBING SLOW - FAST

96 - 127 LED ON

128 - 159 PULSE STROBE SLOW - FAST

160 - 191 LED ON

192 - 223 RANDOM STROBE SLOW - FAST

224 - 255 LED ON

Saber Spot WW 2 Channel Mode

ADJ Products, LLC - www.adj.com - Saber Spot WW Instruction Manual Page 18 ADJ Products, LLC - www.adj.com - Saber Spot WW Instruction Manual Page 19

Channel Value Function

1 WARM WHITE

0 - 255 0% - 100%

2 WARM WHITE FINE

0 - 255 0% - 100%

3 SHUTTER/STROBE

0 - 31 LED OFF

32 - 63 LED ON

64 - 95 STROBING SLOW - FAST

96 - 127 LED ON

128 - 159 PULSE STROBE SLOW - FAST

160 - 191 LED ON

192 - 223 RANDOM STROBE SLOW - FAST

224 - 255 LED ON

4 DIMMER CURVES

0 - 20 STANDARD

21 - 40 STAGE

41 - 60 TV

61 - 80 ARCHITECTURAL

81 - 100 THEATRE

101 - 255 DEFAULT DIMMER SETTING

Saber Spot WW 4 Channel Mode Saber Spot WW Dimmer Curve Chart

(Fade Time) (Fade Time)

Ramp Effect

Standard

Stage

TV

Architectural

Theatre

Saber Spot WW CAD Drawing

108mm [4.3in]

135mm [5.3in]

76mm [3.0in]

28mm [1.1in]

160mm [6.3in]

170mm [6.7in]

215mm [8.5in]

230mm [ 9.1in ]

ADJ Products, LLC - www.adj.com - Saber Spot WW Instruction Manual Page 20 ADJ Products, LLC - www.adj.com - Saber Spot WW Instruction Manual Page 21

Saber Spot WW Photometric Chart

Intensity(LUX)

Beam angle

Field angle 8°

4°

Full LEDs 51890 13030 5536 3093 1956

8°

4°

0

0 1 2 3 4 5

1

2

3

4

Beam opening(m)

3

4

0.15

0.06 0.24 0.33 0.41 4°

Diameter

(m)

0.31

0.13 0.48 0.66 0.83 8°

Diameter

(m)

Saber Spot WW Photometric Chart

Intensity(LUX)

Beam angle 10°

10°

0

0 1 2 3 4 5

1

2

3

4

Beam opening(m)

3

4

0.35

0.17 0.52 0.70 0.87

Diameter

(m)10°

Full LEDs 20880 5399 2303 1339 842

(single face)frost filter

ADJ Products, LLC - www.adj.com - Saber Spot WW Instruction Manual Page 22

Saber Spot WW Cleaning

Saber Spot WW Trouble Shooting

Trouble Shooting: Listed below are a few common problems that

you may encounter, with solutions.

No light output in WW Dimmer Mode;

1. Be sure the strobe setting is set to value 255.

Due to fog residue, smoke, and dust cleaning the internal and exter-

nal optical lenses and mirror should be carried out periodically to

optimize light output. Cleaning frequency depends on the environ-

ment in which the fixture operates (I.e. smoke, fog residue, dust,

dew). In heavy club use we recommend cleaning on a monthly basis.

Periodic cleaning will ensure longevity, and crisp output.

1. Use normal glass cleaner and a soft cloth to wipe down the out-

side casing.

2. Use a brush to wipe down the cooling vents and fan grill.

3. Clean the external optics with glass cleaner and a soft cloth every

20 days.

4. Clean the internal optics with glass cleaner and a soft cloth every

30-60 days.

5. Always be sure to dry all parts completely before plugging the unit

back in.

With this feature you can connect the xtures to one another

using the PowerCON input and output sockets. The quantity that

can be connected is 36 xtures maximum @ 110V and a maxi-

mum 65 xture’s @ 240V. After maximum limit has been reached

you will need to use a new power outlet. They must be the same

xtures. DO NOT mix xtures.

Saber Spot WW Power Cord Daisy Chain Saber Spot WW Photometric Chart

Intensity(LUX)

Beam angle 45°

0

0 1 2 3 4 5

1

2

3

4

Beam opening(m)

3

4

45

1.66

0.83 2.49 3.31 4.1445°

Diameter

(m)

Full LEDs 2870 749 330 194 126

(double face)frost filter

ADJ Products, LLC - www.adj.com - Saber Spot WW Instruction Manual Page 23

ADJ Products, LLC - www.adj.com - Saber Spot WW Instruction Manual Page 24 ADJ Products, LLC - www.adj.com - Saber Spot WW Instruction Manual Page 25

Saber Spot WW Notes Saber Spot WW Warranty

MANUFACTURER’S LIMITED WARRANTY

A. ADJ Products, LLC hereby warrants, to the original purchaser, ADJ Products, LLC products

to be free of manufacturing defects in material and workmanship for a prescribed period from

the date of purchase (see specific warranty period on reverse). This warranty shall be valid only if the

product is purchased within the United States of America, including possessions and

territories. It is the owner’s responsibility to establish the date and place of purchase by acceptable

evidence, at the time service is sought.

B. For warranty service you must obtain a Return Authorization number (RA#)

before sending back the product–please contact ADJ Products, LLC Service Department

at 800-322-6337. Send the product only to the ADJ Products, LLC factory. All

shipping charges must be pre-paid. If the requested repairs or service (including

parts replacement) are within the terms of this warranty, ADJ Products, LLC will pay return

shipping charges only to a designated point within the United States. If the entire instrument is

sent, it must be shipped in it’s original package. No accessories should be shipped with the product. If

any accessories are shipped with the product, ADJ Products, LLC shall have no liability whatsoever for

loss of or damage to any such accessories, nor for the safe return thereof.

C. This warranty is void if the serial number has been altered or removed; if the product is modified in any

manner which ADJ Products, LLC concludes, after inspection, affects the reliability of the product; if the

product has been repaired or serviced by anyone other than the ADJ Products, LLC factory unless prior

written authorization was issued to purchaser by ADJ Products, LLC; if the product is damaged because

not properly maintained as set forth in the instruction manual.

D. This is not a service contract, and this warranty does not include maintnance, cleaning or periodic check

up. During the period specified above, ADJ Products, LLC will replace defective parts at its expense

with new or refurbished parts, and will absorb all expenses for warranty service and repair labor by

reason of defects in material or workmanship. The sole responsibility of ADJ Products, LLC under this

warranty shall be limited to the repair of the product, or replacement thereof, including parts, at the sole

discretion of ADJ Products, LLC. All products covered by this warranty were manufactured after August

15, 2012, and bear indentifying marks to that effect.

E. ADJ Products, LLC reserves the right to make changes in design and/or improvements upon its products

without any obligation to include these changes in any products theretofore manufactured.

No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with

products described above. Except to the extent prohibited by applicable law, all implied warranties made

by ADJ Products, LLC in connection with this product, including warranties of merchantability or fitness,

are limited in duration to the warranty period set forth above. And no warranties, whether expressed or

implied, including warranties of merchantability or fitness, shall apply to this product after said period

has expired. The consumer’s and/or Dealer’s sole remedy shall be such repair or replacement as is

expressly provided above; and under no circumstances shall ADJ Products, LLC be liable for any loss or

damage, direct or consequential, arising out of the use of, or inability to use, this product.

This warranty is the only written warranty applicable to ADJ Products, LLC Products and

supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore

published.

MANUFACTURER’S LIMITED WARRANTY PERIODS:

 •NonL.E.D.LightingProducts=1-year(365days)LimitedWarranty(Such as: Special Effect

Lighting, Intelligent Lighting, UV lighting, Strobes, Fog Machines, Bubble Machines, Mirror Balls, Par

Cans, Trussing, Lighting Stands etc. excluding LED and lamps)

 •LaserProducts=1Year(365Days)LimitedWarranty(excluding laser diodes which have a 6 month

limited warranty)

 •L.E.D.Products=2-year(730days)LimitedWarranty(excluding batteries which have a 180 day lim-

ited warranty). Note:2YearWarrantyonlyappliestopurchaseswithintheUnitedStates.

 •StarTecSeries=1YearLimitedWarranty(excluding batteries which have a 180 day limited war-

ranty).

•ADJDMXControllers=2Year(730Days)LimitedWarranty

Saber Spot WW Specifications

Please Note: Specications and improvements in the design

of this unit and this manual are subject to change without any

prior written notice.

Auto Sensing Voltage: This xture contains a automatic volt-

age switch, which will auto sense the voltage when it is plugged

into the power source.

ADJ Products, LLC

6122 S. Eastern Ave. Los Angeles, CA 90040 USA

Tel: 323-582-2650 / Fax: 323-725-6100

Web: www.adj.com / E-mail: [email protected]

A.D.J. Supply Europe B.V.

Junostraat 2

6468 EW Kerkrade

The Netherlands

[email protected] / www.adj.eu

Tel: +31 45 546 85 00 / Fax: +31 45 546 85 99

Model: Saber Spot WW

Voltage: 100~240V, 50/60Hz

LEDs: 1 x 15W WW LED

LED Life: 10,000 Hrs.

Beam Angle: 4 Degrees

10 Degrees (Frost Filter 1)

45 Degrees (Frost Filter 2)

Power Consumption: 15W

PowerCon Daisy Chain:

Dimensions:

Weight:

Colors:

Duty Cycle:

DMX:

Sound Active:

Working Position:

Warranty:

36 Fixtures Max. (110V

65 Fixtures Max. (240V)

6.7”(L) x 5.3”(W) x 8.5”(H)

170 x 135 x 215mm

2.6 Lbs. / 1.2 kgs.

WW

None

3 DMX Channel Modes: 1/2/4

No

Any Safe, Secure Position

2 Year (730 days)

ADJ Products, LLC - www.adj.com - Saber Spot WW Instruction Manual Page 26

Control: RDM (Remote Device Management)

ADJ SAB605 Saber Spot WW Compact Pinspot Light User manual

This manual is also suitable for

ADJ SAB605 Saber Spot WW Compact Pinspot Light User manual

Related papers

Other documents