Page is loading ...
Astra-Z-8745 Ver. A
Wireless Repeater / Router
Operation Manual
Revision 8745-av1_5_en
This operation manual is intended for studying the operating
principles, proper use, storage, and maintenance of the
Wireless Repeater/Router Astra-Z-8745 version A (hereinafter
referred to as router) (Figure 1).
The manufacturer reserves the right to make alteration regarding
refinement of the product without prior notification. All
improvements are included in new revision of the operation
manual.
List of Abbreviations:
Astra-Zitadel System: Astra-Zitadel on-site Wireless Intrusion /
Fire Detection and Alarming System;
Control panel: Astra-Z-812M / Astra-Z-8945 ver.A Control
Panel;
LT: Astra-942 Laser Tester;
BAT: Battery;
FW: Firmware;
MSS: Astra-Z Monitoring Software Suite.
1 Function
1.1 The router is intended for operation in the
Astra-Zitadel system.
1.2 The router is intended:
- for retransmitting messages (notifications,
control commands, responses, handshakes,
etc.) from wireless devices within the Astra-
Zitadel system through all retransmission levels
to the control panel;
- for automatically routing messages from
wireless devices if the current data transfer route is
lost;
- for controlling external devices connected to the router jack
and powered with 220 V AC.
1.3 The router ensures operation directly with 30 detectors
(plus two mobile devices).
1.4 Power is supplied to the router from 220 V AC network.
The router has 220 V AC circuit protection.
1.5 The router retains operability if the mains AC voltage
varies within the range of 100 to 240 V.
1.6 The router has the potential to connect a backup power
supply unit: a lithium ion polymer rechargeable battery
(hereinafter BAT) of LP704374 type with nominal voltage of 3.7
V and a capacitance of 2200 mA/hour.
2 Specification
Technical Parameters of Radio Channel
Operating frequency range, MHz ..................... 2 400 to 2 483, 5
Number of operating channels at 5 MHz intervals ................... 16
Channel width, MHz .................................................................. 2
Wireless coverage range, line-of-sight, m, min .................... 1000
General Technical Parameters
Main power supply voltage, V ................................................ 220
Current consumption when mains-powered, mA, max:
- in transmitting mode without BAT, registered
in wireless network .................................................................... 8
- in transmitting mode with charging BAT, registered
in wireless network .................................................................. 12
BAT-powered supply voltage, V ...................................... 3 to 4,2
BAT-powered* operating time, h, min ...................................... 24
BAT discharge notification threshold, V ........................... 3.5±0,1
Completely discharged battery charge
time, h, max ............................................................................. 24
Technical readiness time, s, max ............................................ 20
Overall dimensions, mm, max ................................... 140×79×67
Weight (without BAT**), kg, max ........................................ 0,155
Operating Conditions
Temperature range, °C ........................................ from -30 to +50
Relative air humidity, % .................................. up to 95 at +35 °C
without moisture condensation
____________________________________________
*At temperature below 0 °C the BAT-powered operating time is significantly
less.
** BAT weight = 0.044 kg
3 Package Contents
Router delivery package contents:
Astra-Z-8745 Version A ................................................... 1 pcs.
Operating Manual ............................................................. 1 copy
Note - BAT is supplied separately.
4 Structure
4.1 Structurally the router is designed as a housing combined
with a 220 V plug and jack. Mounted inside the housing is a
printed circuit board (PCB) with radio elements (Figure 2).
Figure 2
4.2 The base has a slot for inserting BAT. The PCB has a
socket for connecting BAT outputs.
4.3 Mounted on PCB are red and white LEDs for router’s
functional status and the wireless network status supervision
respectively.
4.4 Mounted on PCB is a button for initiating the network
registration procedure without housing opening.
5 Notification Types
Table 1: Notifications processed by LEDs and Control Panel (or
MS interface)
Notification
Type
Red
LED
White
LED
Control
Panel
Standby
mode start
Lights up one
time for 1 to 20
seconds after
powering up
Not lit
-
Normal
Not lit
Not lit
+
BAT discharge
Triple blink every
25 seconds
Not lit
+
Main power
supply failure
Not lit
Not lit
+
BAT failure
Not lit
Not lit
+
Figure 1
Revision 8745-av1_5_en
2
Notification
Type
Red
LED
White
LED
Control
Panel
BAT
missing
Blinks with
frequency of 5
Hz during 5 sec.
after 5 sec of
detecting the
missing
Not lit
+
Network
search
Not lit
Blinks with
frequency of 5
Hz for 1 to 60
seconds
-
No network
Not lit
Double blink
every 25
seconds
-
Command
received from
LT
Lights up one
time for 2
seconds upon
receipt of
command from
any LT button
-
-
+: notification issued; –: notification not issued
6 Operating Modes
6.1 Operating modes initiated by the Astra-942 laser
tester buttons:
1) test (upper button);
2) wireless network optimization (middle button);
3) router registration in wireless network (lower button).
6.2 Firmware update
The router`s FW is updated via radio upon a command from
Astra-Z-812M control panel or Astra-Z MSS in accordance with
the Astra-Zitadel Quick Start Guide*.
7 Pre-starting Procedure
7.1 After transportation in conditions differing from those of
operation, the router must be kept unpacked for 4 hours in the
expected operating conditions.
7.2 BAT Installation (if necessary)
Step-1
Remove the cover by driving two
screws from the router housing on
the plug-side.
Step-2
Install BAT as follows:
a) Remove the PCB by bending back the latch holding it in
place.
b) Insert BAT.
c) Reinstall the PCB.
d) Connect BAT outputs to the special socket on the PCB.
The red LED lights up for 1 to 20 seconds.
Step-3
Replace the cover and tighten screws.
7.3 Registering the Router in the Wireless Network
Router registration is required for identification in the wireless
network in which it is supposed to operate.
7.3.1 Registering the router in Astra-Z-812M control panel
Step-1
Turn the router ON by plugging it into the selected 220 V
outlet at the site.
Step-2
Switch the control panel to Wireless component
registration mode by the method described in an
appropriate Astra-Zitadel system operation manual* or Quick
Start Guide*.
Step-3
The router can be registered by one of two methods:
a) by command from the LT;
b) using the hidden registration initiation button.
Step-4
Initiating Router Registration Procedure Using LT (can
be conducted with router assembled):
1) Press the lower button on the LT and hold until a beam
appears.
2) Direct the laser beam at the router LED and irradiate it for
at least 1 second.
The router’s red LED lights up for 2 seconds, and then the
white LED blinks with a frequency of 5 Hz for not more than
60 seconds («Network search» mode).
Step-5
Initiating Router Registration Procedure
Using the Hidden Registration Initiation
Button:
Shortly (for 0.5 to 2.5 seconds) press the
hidden registration initiation button through
the opening on the side edge of the router
housing.
The router’s white LED lights up at a
frequency of 5 Hz during the wireless network
search, but not more than 60 seconds.
Step-6
Verify registration by the control panel indication:
If registration procedure completed successfully, the
control panel screen displays «RTRxxx registered»
notification.
If registration procedure failed, the control panel screen
displays «Registration time expired» notification. In this
case, repeat the registration procedure, i.e. execute steps 2
and 4 or 2 and 5.
Step-7
After successful registration of the router, for long term storage
before its installation, it is allowed to switch the router OFF.
When power is supplied, there is no need to re-register the
router in the same wireless network if it was not intentionally
removed from the network through Astra-Z-812M control panel.
Step-8
Verify Router Operability:
1) Verify the router status on the control panel LED
(«Normal» status should appear).
2) Initiate test mode in accordance with the appropriate
Astra-Zitadel system Quick Start Guide*.
Make sure appropriate notification is issued.
7.3.2 Registering the router in Astra-Z-8945 control panel
Step-1 Perform p.7.2 if necessary.
Step-2
Set Astra-Z MSS on PC according to method described in
Astra-Zitadel system based on Astra-Z-8945 ver.A control
panel Operating manual* or Quick Start Guide*. Run
Setup module. Choose Wireless network / List of
wireless devices menu item. Right click any empty row
and choose Register wireless devices command from
pop-up menu.
Screws
Revision 8745-av1_5_en
3
Step-3
Initiate router registration procedure by one of 2 methods
(see p.7.3.1):
a) using the LT;
b) using the dedicated hidden registration initiation
button.
Step-4
Make sure the registration procedure is completed
according to the procedure described in the Astra-Zitadel
system operating manual* or Quick Start Guide*:
Once registration procedure completed successfully,
«RTR» appears in selected row.
In case registration procedure failed repeat registration
procedure.
Step-5
Verify Router Operability:
1) Verify the router status on the MSS interface («Normal»
status should appear).
2) Initiate test mode in accordance with the appropriate
Astra-Zitadel system Quick Start Guide*.
Make sure appropriate notification is issued.
Step-6
After successful registration of the detector, for long term
storage before its installation, it is allowed to switch the
router OFF.
When power is supplied, there is no need to re-register the
router in the same wireless network if it was not intentionally
removed from the network through Astra-Z MSS.
7.4 Charging Battery
7.4.1. Prior to use, make sure that the BAT in the router is
fully activated via one charge/discharge cycle in the router.
In order to achieve this, charge the battery for at least 10
hours, fully discharge it by disconnecting the external power
supply unit for at least 24 hours, and then recharge it for at
least 24 hours
7.4.2 It is permissible to begin using the router with partially
discharged BAT if a training cycle is conducted and the
external power supply voltage is guaranteed to be
uninterrupted.
7.4.3 The BAT is recharged within the router when it is
connected to a standard 220 V AC network. Full charge of a
fully discharged BAT takes 24 hours.
8 Maintenance
To ensure the alarm system reliable operation, testing and
maintenance of the router is recommended as follows:
- Inspect the integrity and secure fastening of the router
housing at least once a month;
- Verify router operability by the method described in p.7.3
at least once a month;
- Clean contaminants from the router at least once in three
months.
9 Labeling
The following information is marked on the label attached to the router
housing:
- manufacturer trademark;
- abbreviated router designation;
- firmware version;
- month and year (last two digits) of manufacture;
- conformity mark (if an appropriate certificate is available);
- bar-code that duplicates textual information.
10 EC Conformity Declarations
This product is in conformity with the provisions of:
R&TTE Directive 1999/5/EC, Article 10.5;
EN 60950: 2001 Safety of information technology equipment;
EN 50371 Generic standard to demonstrate the compliance of low-
power electronic and electrical apparatuses with the basic restrictions
related to human exposure to electromagnetic fields (10 MHz - 300
GHz) – General public;
EN 301489-17 V1.1.1 (09-2000) Electromagnetic Compatibility and
radio spectrum Matters (ERM); Electromagnetic Compatibility (EMC)
standard for radio equipment and services; Part 17: Specific conditions
for wideband data Hiperlan equipment;
EN 300220-1 V1.3.1 (2000-09) Electromagnetic compatibility and
Radio spectrum Matters (ERM); Short range devices; Technical char-
acteristics and test methods for radio equipment to be used in the 25
MHz to 1 000 MHz frequency range with power levels ranging up to
500 mW; Part 1: Parameters intended for regulatory purposes.
Construction of the detector provides for protection class IP41.
11 Recycling
11.1 The router poses no threat to human life / health or to the
environment; after its service life is over, it can be recycled without any
special environmental protection measures.
11.2 Recycle BAT by giving spent BAT to a trade organization, service
center, equipment manufacturer, or organization that accepts spent
batteries.
12 Warranty Terms
12.1 Quality Management System meets provisions of ISO 9001-2011.
12.2 The manufacturer guarantees the compliance of the router to
specifications on condition that user observes required conditions of
transportation, storage, installation and operation.
12.3 The storage warranty period is 5 years and 6 months from the date
of manufacture.
12.4 The operating warranty period is 5 years from the startup date, but
not more than 5 years and 6 months from the date of manufacture.
12.5 The manufacturer guarantees replacement or repair of the product
during the warranty period.
12.6 The warranty doesn’t come into effect in the following cases:
- not adherence to the operating manual;
- mechanical damage to the router;
- repair of the router by any third-party service except the
Manufacturer.
12.7 The warranty applies to the router only. All equipment from other
manufacturers used in conjunction with the router is subject to its own
warranty terms.
The manufacturer bears no responsibility for death, injury, proper-
ty damage or other incidental or premeditated loss based on us-
er's statement that the device failed to implement its functions.
* Available for free downloading from www.controlex.eu
Sales:
Controlex GmbH
Warranty service and
technical support:
ТЕКО-TD
Philosophenweg 31-33
47051 Duisburg, Germany
Phone: +49 (0) 203 / 393 91 188
Fax: +49 (0) 203 / 393 91 189
GSM: +49 (0) 178 / 218 48 22
E-mail: info@controlex.eu
Web: www.controlex.eu
Prospect Pobedy str. 19
420138 Kazan, Russia
Phone: +7 (843) 261-55-75
Fax: +7 (843) 261-58-08
E-mail: info@teko.biz
suppor[email protected]
Web: www.teko.biz
Made in Russia
/