Innervision Technology Tough-PAC Assembly Instructions

Brand
Innervision Technology
Model
Tough-PAC
Category
Tablet cases
Type
Assembly Instructions
Innervision Technology Ltd SOP002/F/MFG/280214
SOP002_Air_Assembly Instructions Page 1 Effective Date 24/9/14
Assembly Instructions
For iPad Air
Package Contents (assembled)
Front case: Support washers x2 Black
Support Blocks x2 Grey
Screen seal with home button
Rear Case: iPad shock support (moulded pad)
Sleep button
Antibacterial Screen protector
Case screws x10 (Pack)
Screw port plugs x10 (Pack)
Tools Required: T10 torx screwdriver (not included)
(If available a 0.5N.m Torque driver is preferred)
Warning: This package contains small parts and
plastic packaging that may present a danger or
choking hazard, not suitable for small children.
A competent person should do the assembly.
Please read these instructions completely
before assembly. Tough-PAC is designed to be
fitted as a semi-permanent case for iPad Air.
iPad Air Screen Protector
The antibacterial screen protector provided
should be fitted to iPad Air before case
assembly - see enclosed instruction sheet.
You may decide to use an alternative type of
screen protector or even not use one at all.
Case Assembly
1. Check the sleep button is in the slot inside
the rear case as shown below.
2. Check that the camera window is free of
obstructions
1
.
3. Check the front case lower support blocks
and top washers are in place as shown.
4. Check that the screen seal and Home
button is properly seated into the lower
hole of the front case. The seal is shaped to
fit the case moulding; it should be carefully
positioned onto the case so the seal lip fits
snugly around the screen aperture - gently
press into position with your finger around
the inner edge.
1
If you do not wish to use the camera for confidentiality
reasons place a sticker or blanking disc over the camera
window.
Innervision Technology Ltd SOP002/F/MFG/280214
SOP002_Air_Assembly Instructions Page 2 Effective Date 24/9/14
5. Make sure there is no debris on the inside
face of the screen seal.
6. Place iPad face down onto the screen,
centrally between the black support blocks
with the bottom of iPad pressed well down
on to the two lower grey support blocks.
7. Place the two Air support straps over iPad
and onto the front case lugs as shown
8. Place the rear case close to the front case
and attach the 8pin connector to your iPad.
Keeping the foam pad in place flip over and
align the rear case assembly over the front
case and gently press into position
2
. Take
care not to trap the cable - tuck it inside if
needed. (See note below if using the Audio
version)
9. Press and hold the rear case down and
check the function of the sleep button. It
should definitely ‘click’ on/off.
10. When the function of the sleep button
feels satisfactory insert 4 case screws into
screw ports 1-4 as shown; while holding
the rear case in position screw down the
screws until fully home
3
(torque 0.5N.m -
finger tight) and the case halves closed
properly together - the case seal will
compress.
2
If using the Audio version fully insert the 3.5mm audio jack
into the iPad audio socket before closing the case.
3
DO NOT use a power screwdriver as it will damage the screw
bosses. A torque of 0.5N.m (50cN.m) is recommended.
Innervision Technology Ltd SOP002/F/MFG/280214
SOP002_Air_Assembly Instructions Page 3 Effective Date 24/9/14
11. Turn over the unit and check that the iPad
and screen protector are properly aligned.
12. Check the Home & Sleep buttons are
functioning correctly with iPad. If needed
adjust iPad position, by holding the case
upright and gently tapping the base onto a
work surface to settle the iPad onto the
lower support blocks.
13. Now insert the remaining 6 screws into the
rear case
4
. Insert the screw nearest the
camera window last.
14. Optional – when you are satisfied the
assembly is complete and functioning
correctly insert the 10 screw port plugs
into the rear case screw ports and press in
until just below the case surface
5
.
4
It is best to screw down opposite screws around the case until
all are properly seated.
5
Use of these parts may not be safe for children.
Cleaning
Tough-PAC may be cleaned using household or
professional disinfectant or detergent wipes.
Isopropyl alcohol or weak ‘active oxygen’ based
sprays are also acceptable (according to your local
cross infection control policy). Clean the camera
ports and/or screen with a micro-fibre cloth. DO
NOT use any acid or solvent (e.g. Acetone) based or
abrasive cleaning materials else damage to the
plastic parts will occur.
Port plug removal
Using a pointed tool or tweezers firmly pierce the
centre of the plug at an angle and pull it out
vertically. Do not lever out the plugs – it will
damage the plastic housing. Replace with a new
plug on re-assembly.
Warranty
Tough-PAC case and cradle is guaranteed for 12
months from date of purchase against faulty parts
or manufacturing defects. Please Call or email
Innervision with details of the problem, where
necessary we will issue a return number for you to
send it back to your reseller or Innervision for
repair or replacement.
Limitations of liability.
The product warranty does not cover damage or
faults caused by abuse, misuse, accidental damage,
drops, immersion or incorrect assembly of the
product. This includes over tightening of screws
into plastic housings or exposure to harmful
chemical cleaning agents, solvents (e.g. Acetone),
adhesives or excessive heat.
Tough-PAC® cannot protect iPad against all forms
of damage. The user is responsible for proper
handling care and use of this equipment.
Tough-PAC has an IP rating of IP5x (dust protected)
and IPx3 (light spray) for fluid ingress. Tough-PAC is
not waterproof.
Charging iPad in Tough-PAC
Dock the assembled Tough-PAC & iPad case into the
cradle cup, handle upwards, screen facing forwards.
The iPad will begin charging indicated by the
battery sign and bleep. For best results allow iPad
to enter into sleep mode whilst charging. When
using a USB cradle connected to a PC or Mac
computer, iPad may begin synchronising via iTunes.
Innervision Technology Ltd SOP002/F/MFG/280214
SOP002_Air_Assembly Instructions Page 4 Effective Date 24/9/14
The setup and use of iPad will affect its charging
rate; especially screen brightness, use of cellular
services, and allowing sleep mode whilst charging.
See www.apple.com/batteries/ipad.html for more
information about charging iPad. Battery life is
model and use dependent.
If a 'Not Charging' message is seen when attached
to a PC or Mac there may not be adequate power
output from the PC USB port, iPad requires at least
1A output. Some USB ports only provide 0.5A.
Trouble shooting
The sleep/power button is being held on; iPad
shows the shut down message? Recheck the
assembly. If necessary Loosen the ‘last’ screw
nearest the rear camera window ½ a turn until the
button definitely clicks when pressed.
The case seems a little tight when docking into
the cradle recess or charging is not effective.
Check that the case screws are properly seated; it
may be necessary to tighten the case screws
slightly to pull the case fully together.
The iPad buttons do not seem to work properly.
Check the alignment and position of iPad in the
case. Adjust as necessary to achieve correct
functionality. The iPad Air's screen should be
central in the aperture window with a small border
showing evenly all the way around. The screen seal
is designed to have a small lip around the edge of
the screen aperture. The rear camera should be
just off central within the rear case aperture. The
sleep button should provide a definite ‘click’ onto
iPad when pressed.
If the unit has been dropped it may be that iPad
has shifted and will need to be realigned.
iPad2 does not seem to fit properly
This variant of Tough-PAC is designed to fit iPad Air
only.
Spares & Replacements
Replacement parts may be obtained from
Innervision Technology or your reseller.
Coloured sleep buttons (Red, Green, Blue,
Orange)
Replacement screen protectors
Replacement Screen seals
Screws & Screw port plugs
Case Parts
Shock Pads
Please dispose of all packaging responsibly.
Contact & Support:
Innervision Technology Ltd
Unit 6 Red Hill Farm Business Park
Red Hill
Medstead, ALTON
GU34 5EE
UK
Tel: +44 1420 563538
E: connect@innervisiontechnology.com
This product contains parts that include Biomaster
silver biocide tested to ISO 22196:2011
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Innervision Technology Tough-PAC Assembly Instructions

Brand
Innervision Technology
Model
Tough-PAC
Category
Tablet cases
Type
Assembly Instructions
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents