Pelco HS2100 User manual

Brand: Pelco

Model: HS2100

Category: Security camera accessories

Type: User manual

C1465M-A (9/06)

INSTALLATION

HS2100

Ceiling Enclosure

2 C1465M-A (9/06)

Important Safety Instructions

1. Installation and servicing should be done only by qualified service personnel and conform to all Local codes.

2. Unless the unit is specifically marked as a NEMA Type 3, 3R, 3S, 4, 4X, 6, or 6P enclosure, it is designed for indoor use only and it must not

be installed where exposed to rain and moisture.

3. Only use replacement parts recommended by Pelco.

4. After replacement/repair of this unit’s electrical components, conduct a resistance measurement between line and exposed parts to verify

the exposed parts have not been connected to line circuitry.

5. The installation method and materials should be capable of supporting four times the weight of the enclosure, pan/tilt, camera and lens

combination.

The product and/or manual may bear the following marks:

This symbol indicates that dangerous voltage constituting a risk of

electric shock is present within this unit.

This symbol indicates that there are important operating and

maintenance instructions in the literature accompanying this unit.

Description

The HS2100 is a low-profile, high-security ceiling enclosure with rivited back box for mounting in fixed or dropped ceilings. The unobtrusive,

compact design complements any business or office decor and provides maximum surveillance for fixed applications when using CCD cameras.

The HS2100 is engineered for ease of installation and service. The upper section, mounted above the ceiling, is constructed of aluminum.

Because of its lightweight design, the upper section can be mounted directly on a ceiling tile without the use of additional mounting plates.

The lower section is made of steel to provide extra security. It is hinged to provide convenient access for camera and lens adjustments. The

adjustable camera mounting sled allows the camera to be positioned vertically or horizontally, depending on the camera size.

OPTIONAL ACCESSORY

E2100 Rotating mounting plate with 360 degrees of rotation in 10-degree increments. Features locking capability to secure enclosure

positioning. Replaces 2-ft x 2-ft (60.96 cm x 60.96 cm) ceiling tile. Can be used in 2-ft x 4-ft (60.96 cm x 121.92 cm) ceiling tile

with additional “T” rail for support. Constructed of aluminum with textured white polyester powder coat finish.

CAUTION:

RISK OF ELECTRIC SHOCK.

DO NOT OPEN.

C1465M-A (9/06) 3

Installation

The following items are supplied:

1Enclosure

1 Parts bag (Parts may be used to attach the camera to the mount.)

1 Hex bolt, 1/4-20 x 1/2"

1 Split washer

1Flat washer

1 Backup flanges to support the enclosure if adequate mounting support is not available or if enclosure is mounted in drop ceiling tiles

1 Pin-in-hex wrench to remove tamper-resistant screw

Recommended Tools

Pelco does not supply the basic tools needed for the installation process. The following tools are recommended:

Small adjustable wrench

Phillips screwdriver

BNC crimp tool

Wire stripper

Wire cutter

Coaxial cable stripper

BACK BOX INSTALLATION

To mount the HS2100, perform the following steps:

NOTE: Backup flanges have been supplied to support the enclosure if adequate mounting support is not available or if you are mounting the

enclosure in drop ceiling tiles.

1. Determine the location and direction of the enclosure to be mounted. Ideally, the enclosure cutout should be parallel and adjacent, or

perpendicular, to any ceiling structure. Avoid cutting into any ceiling structural members.

2. Unlock the enclosure cover by unscrewing the tamper-resistant screw (pin-in-hex wrench is included to remove tamper-resistant screw).

Open the cover to expose the mounting holes in the flange.

3. Remove any appropriate knockouts.

4. Insert the enclosure into the opening and secure with the appropriate fasteners.

CAMERA AND LENS INSTALLATION

To mount the camera and lens, perform the following steps:

1. Mount the camera and lens onto the adjustable camera cradle. Adjust the position of the camera and lens to clear the enclosure cover

when closed. Tighten the camera cradle fasteners.

2. Route the appropriate cables into the enclosure. Make all necessary electrical connections. Refer to Table A for the type of video coaxial

cable to use. If the camera will use 24 VAC power, refer to Table B to determine the size of wire needed.

3. Close and lock the cover with the provided tamper-resistant screw.

4 C1465M-A (9/06)

*Cable requirements:

75 ohms

All-copper center conductor

All-copper braided shield with 95-percent braid coverage

EXAMPLE: An enclosure that requires 30 VA and is installed 94 feet (28 m) from the transformer would require a minimum wire gauge of

20 AWG.

NOTE: Distances are calculated feet; values in parentheses are meters.

Table A. Video Coaxial Cable Wiring Distances

Cable Type* Maximum Distance

RG59/U 750 ft (229 m)

RG6/U 1,000 ft (305 m)

RG11/U 1,500 ft (457 m)

Table B. 24 VAC Wiring Distances

The following are the recommended maximum distances for 24 VAC applications and are calculated with a 10 percent voltage drop.

(Ten percent is generally the maximum allowable voltage drop for AC-powered devices.)

Wire Gauge

Total VA

(0.4 mm

)

(0.5 mm

)

(1.0 mm

)

(1.5 mm

)

(2.5 mm

)

(4.0 mm

)

(6.0 mm

)

178

(54)

283

(86)

451

(137)

716

(218)

1142

(348)

1811

(551)

2880

(877)

Maximum distance from

transformer to load

(27)

141

(42)

225

(68)

358

(109)

571

(174)

905

(275)

1440

(438)

(17)

(28)

150

(45)

238

(72)

380

(115)

603

(183)

960

(292)

(13)

(21)

112

(34)

179

(54)

285

(86)

452

(137)

720

(219)

(10)

(17)

(27)

143

(43)

228

(69)

362

(110)

576

(175)

C1465M-A (9/06) 5

Maintenance

Regularly scheduled maintenance will prolong the operational life and appearance of the enclosure. Clean the outer surface of the enclosure

with a nonabrasive cleaning cloth and antistatic cleaner. Clean the viewing window with a mild, nonabrasive soap and water to maintain picture

clarity. Do not use kerosene or similar substances that may damage the surface.

6 C1465M-A (9/06)

Specifications

GENERAL

Environment Indoor only

Operating Range 32° to 120°F (0° to 49°C)

Weight 5.30 lb (2.41 kg)

MECHANICAL

Construction

Upper section 5052-H32 aluminum

Lower section 16 gauge steel

Viewing window 0.25" (6.35 mm) thick, abrasion-resistant Lexan

polycarbonate resin thermoplastic

Finish White polyester powder coat

Cable Entry Two cable knockout holes

Dimensions See dimension drawing

Lock Tamper-resistant 8-32 screw

(Pin-in-hex wrench included to remove tamper-resistant screw.)

Ceiling Mounting Upper section flange-mounted to fixed ceiling or ceiling tile. Ceiling support rails are provided.

Maximum Camera/Lens Size 3" H x 4" W x 10" L (7.62 x 10.16 x 25.4 cm)*

*Dimensions include BNC connector

Length may vary if width and height of camera and lens are different.

Camera Mounting Adjustable camera sled capable of supporting a maximum weight of 10 lb (4.53 kg). Sled can be adjusted

horizontally or vertically.

(Design and product specifications are subject to change without notice.)

5.75

(14.61)

11.75

(29.85)

7.50

(19.05)

7.00

(17.78)

3.50

(8.89)

13.50

(23.29)

MAX CAMERA LENGTH

10.00 (25.40)

NOTE: VALUES IN PARENTHESES ARE CENTIMETERS;

ALL OTHERS ARE INCHES.

PRODUCT WARRANTY AND RETURN INFORMATION

WARRANTY

Pelco will repair or replace, without charge, any merchandise proved defective in material or

workmanship for a period of one year after the date of shipment.

Exceptions to this warranty are as noted below:

• Five years on FT/FR8000 Series fiber optic products.

• Three years on Genex

Series products (multiplexers, server, and keyboard).

• Three years on Camclosure

and fixed camera models, except the CC3701H-2,

CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and MC3651H-2X camera models,

which have a five-year warranty.

• Three years on PMCL 200/300/400 Series LCD monitors.

• Two years on standard motorized or fixed focal length lenses.

• Two years on Legacy

, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series fixed

dome products.

• Two years on Spectra

, Esprit

, ExSite

™

, and PS20 scanners, including when used in

continuous motion applications.

• Two years on Esprit

and WW5700 Series window wiper (excluding wiper blades).

• Two years (except lamp and color wheel) on Digital Light Processing (DLP

) displays.

The lamp and color wheel will be covered for a period of 90 days. The air filter is not

covered under warranty.

• Eighteen months on DX Series digital video recorders, NVR300 Series network video

recorders, Endura

™

Series distributed network-based video products, and TW3000 Series

twisted pair transmission products.

• One year (except video heads) on video cassette recorders (VCRs). Video heads will be

covered for a period of six months.

• Six months on all pan and tilts, scanners or preset lenses used in continuous motion

applications (that is, preset scan, tour and auto scan modes).

Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco

shipment. All goods requiring warranty repair shall be sent freight prepaid to Pelco, Clovis,

California. Repairs made necessary by reason of misuse, alteration, normal wear, or accident

are not covered under this warranty.

Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from

the specific use or application made of the Products. Pelco’s liability for any claim, whether

based on breach of contract, negligence, infringement of any rights of any party or product lia-

bility, relating to the Products shall not exceed the price paid by the Dealer to Pelco for such

Products. In no event will Pelco be liable for any special, incidental or consequential damages

(including loss of use, loss of profit and claims of third parties) however caused, whether by

the negligence of Pelco or otherwise.

The above warranty provides the Dealer with specific legal rights. The Dealer may also have

additional rights, which are subject to variation from state to state.

If a warranty repair is required, the Dealer must contact Pelco at (800)þ289-9100 or

(559) 292-1981 to obtain a Repair Authorization number (RA), and provide the following

information:

1. Model and serial number

2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number

3. Details of the defect or problem

If there is a dispute regarding the warranty of a product which does not fall under the

warranty conditions stated above, please include a written explanation with the product when

returned.

Method of return shipment shall be the same or equal to the method by which the item was

received by Pelco.

RETURNS

In order to expedite parts returned to the factory for repair or credit, please call the factory at

(800) 289-9100 or (559) 292-1981 to obtain an authorization number (CA number if returned for

credit, and RA number if returned for repair).

All merchandise returned for credit may be subject to a 20% restocking and refurbishing

charge.

Goods returned for repair or credit should be clearly identified with the assigned CA or RA

number and freight should be prepaid. Ship to the appropriate address below.

If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to:

Service Department

Pelco

3500 Pelco Way

Clovis, CA 93612-5699

If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are

instructed to return goods to the USA, you may do one of the following:

If the goods are to be sent by a COURIER SERVICE, send the goods to:

Pelco

3500 Pelco Way

Clovis, CA 93612-5699 USA

If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:

Pelco c/o Expeditors

473 Eccles Avenue

South San Francisco, CA 94080 USA

Phone: 650-737-1700

Fax: 650-737-0933

The materials used in the manufacture of this document and its components are compliant to the requirements of Directive 2002/95/EC.

REVISION HISTORY

Manual # Date Comments

C1465M 6/97 Original version.

C1465M-A 9/06 Updated to new format. Updated viewing window specifications per ECO 05-13392.

Endura and ExSite are trademarks of Pelco.

DLP is a registered trademark of Texas Instruments, Inc.

Lexan is a registered trademark of the General Electric Company.

Worldwide Headquarters

3500 Pelco Way

Clovis, California 93612 USA

USA & Canada

Tel: 800/289-9100

Fax: 800/289-9150

International

Tel: 1-559/292-1981

Fax: 1-559/348-1120

www.pelco.com

ISO9001

Australia

Canada

Finland

France

Italy

Russia

Singapore

Spain

Sweden

The Netherlands

United Arab Emirates

United Kingdom

United States

Pelco HS2100 User manual

Brand: Pelco

Model: HS2100

Category: Security camera accessories

Type: User manual

Download PDF

report

Pelco HS2100 User manual

Pelco HS2100 User manual

Related papers

Other documents