Allure 79996 Operating instructions

Brand
Allure
Model
79996
Type
Operating instructions

This manual is also suitable for

Natural Stone Shower
Wall & Pan
Installation Instructions
Toll Free Phone: 1-866-843-8453
Email: [email protected]
Web: http://www.mydiygenius.com
Shower Wall
& Pan Systems
SWP Instructions English-French.indd 1 11/16/11 3:37 PM
© Vertex Services Limited, 2011
1
3
5
2
4
6
Note: double-up
studding at front for
Cam and Shower Door
installation (refer to
Steps 14 and 24)
Ensure allowance is
made for Backer Board
material and Allure Natural
Stone Wall panels, when
laying out plumbing
allowance for shower head
allowance for faucet
Prior to installing backer
board material, apply sealant
to the moisture barrier sealing
strips on all three sides of the
Allure Shower Pan
Dry fit Allure Shower
Pan to ensure proper fit and
spacing before using mortar
cement to install Shower Pan
36”
36”
84”
(minimum)
Recommended for use:
Custom Building Products
SpeedSet Fast-Setting
Thin-Set Mortar Grey
Recommended for
use: Phenoseal or DAP,
Kitchen and Bath
Sealant, Clear
HANDY HINT
Install backer board material on side
shower walls first, then back wall.
SWP Instructions English-French.indd 2 11/16/11 3:37 PM
© Vertex Services Limited, 2011
7 8
10
9
11 12
Recommended for use:
Custom Building Products
OmniGrip Maximum Strength
Adhesive (Type 1).
Follow manufacturer’s
guidelines for use
Do not kneel or tread on
Allure Natural Stone Shower
Wall panels!
If plumbing is located on left or right
shower panel, be sure to measure for hole cut-
outs after back shower panel is installed
Apply sealant to
BOTH FACES of the
Moisture Barrier Sealing
Strips prior to installing
each side shower wall
NOTE: Plumbing
hardware could be located on
the left, right or center shower
panel. Be sure to dry fit prior
to final installation. These
installation instructions show
back shower wall plumbing,
your installation may differ
Drill using
carbide or diamond
bit for hole cutouts.
Top hole requires 1
3/8” bit. bottom hole
requires 4 3/8” bit.
HANDY HINT
Use the cardboard packaging as a template
to mark out hole positions for the plumbing
HANDY HINT
It is recommended to dry fit the back
shower wall to ensure proper fit prior
to moving to Step 11
Installation requires 1/2”
backer board material. Use
backer board manufacturer
recommended screws
NOTE: Plumbing
hardware could be located on
the left, right or center shower
panel. Be sure to dry fit prior to
final installation
NOTE: Back panel
has Moisture Barrier
Sealing Strips
Recommended for use:
Phenoseal or DAP, Kitchen
and Bath Sealant, Clear
Which
shower
panel do
I install
first?
The back shower panel must be installed first as
it is wider than the side shower panels. If plumbing
is located on back shower panel, proceed to
Step 9 for drilling instructions. If plumbing
is located on either side shower
panel, install back shower
panel first, then move
to side panels
SWP Instructions English-French.indd 3 11/16/11 3:38 PM
© Vertex Services Limited, 2011
1413
15 16
17
20”
20”
20”
20”
NOTE: Apply adhesive 2” from edge to
allow for trim kit pieces. See Step 22.
Repeat Steps
12 to 14 for
right hand shower panel
Use No.10 x 2” screws minimum.
Ensure Cam handles are in the DOWN
position for LEFT side shower panel.
Also ensure Cam handle is pressed tightly
up against shower panel edge prior to
fastening Cam to wall with screws
Ensure Cam handles are in the UP
position for RIGHT side shower panel.
Also ensure Cam handle is pressed tightly
up against shower panel edge prior to
fastening Cam to wall with screws
Hand tighten all six
Cams to close any gaps
at rear corner seams
45° connector (x 2)
Patented Allure Shower Wall Installation Tool (3 sets)
Short tube (x 2)
90° connector Threaded socket (x 2)
Tommy bar (x 2)
Long tube (x 2)
SWP Instructions English-French.indd 4 11/16/11 3:38 PM
© Vertex Services Limited, 2011
18
19
2120
24hrs
NOTE: Retighten Edge Cams after
tightening Tommy Bars
Tighten Tommy
Bars until all 3 shower
walls are pressed flat
into adhesive and backer
board material
SWP Instructions English-French.indd 5 11/16/11 3:38 PM
© Vertex Services Limited, 2011
22 23
24
Install Edge Trim kits
starting from bottom and
moving up.
Recommended
for use: Custom Building
Products SpeedSet Fast-
Setting Thin-Set Mortar Grey
Recommended
for use: Custom Building
Products Polyblend grout
matching silicone.
Install plumbing
fixtures and fittings
HANDY HINT
Allow Edge Trim to dry 24 hours
before installing shower door.
Follow shower door manufacturer’s
instructions to install door.
When drilling into natural stone, use
diamond or carbide tip drill bits.
HOW TO HANDLE ALLURE SHOWER WALLS:
SWP Instructions English-French.indd 6 11/16/11 3:38 PM
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

Allure 79996 Operating instructions

Brand
Allure
Model
79996
Type
Operating instructions
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents