CMC III Power Supply
Bloc d'alimentation CMC III
DK 7030.060
Installationsanleitung und Kurz-Bedienungsanleitung
Installation Guide and Short User’s Guide
Notice d'installation et notice d'utilisation succincte
1 Rittal CMC III Power Supply / Bloc d’alimentation
Abb./Fig./Fig. 1: Beigelegtes Zubehör / Provided accessories / Accessoires joints
Abb./Fig./Fig. 2: Montage / Assembly / Montage
Abb./Fig./Fig. 3: Bedienfeld, Stecker und Anschlüsse / Operator panel, plugs and connectors / Panneau de
commande, fiches et raccordements
Abbildungen /
Figures / Figures
Abbildungen / Figures / Figures
Page is loading ...
Page is loading ...
Page is loading ...
EN
5 Rittal CMC III Power Supply
1 Notes on documentation
This installation and short user's guide is intended for experienced trained specialists and contains only
the most important information concerning the assembly, installation and function of the CMC III Power
Supply (subsequently called power pack).
1.1 Associated documents
CMC III Power Supply assembly, installation and user's guide.
It is available at www.rittal.com and contains the complete application-relevant information and techni-
cal data for the power pack with regard to:
– Further assembly possibilities
– Details concerning the electrical connection
– Functions and services
– Configuration possibilities
– Detailed operating instructions
– Troubleshooting
2 Safety instructions
– Assembly and installation of the device may only be performed by experienced trained specialists.
– Any required mains power connection or a mains power wiring as part of the power pack wiring may
only be performed by an experienced electrician.
– The power pack housing must not be opened.
– The power pack may not come in contact with water, aggressive or inflammable gases and vapours.
– The power pack may only be operated within the specified environmental conditions (see
Section 3.4).
3 Product description
3.1 Functional description
The CMC III Power Supply is used for the power supply of the CMC III system. It can be connected
both to the socket and the input terminals of the CMC III PU or the CMC III CAN-Bus Unit.
3.2 Proper use
The power pack is used only for the power supply to the CMC III PU and possibly for additional power
supply to the CMC III CAN-Bus Unit. Any other use is not permitted.
3.3 Scope of delivery
– CMC III Power Supply
– Provided accessories (see Fig. 1)
– Installation and Short User's Guide
Notes on documentation, Safety instructions, Product description
EN
Rittal CMC III Power Supply 6
EN
3.4 Operating conditions
The power pack may only be operated under the following operating conditions:
4 Assembly
4.1 Assembly instructions
The assembly of the power pack is made as shown in Fig. 2.
5 Installation and operation
5.1 Operating and display elements
The operating and display elements are shown in Fig. 3.
Key for Fig. 3
1 Multi-LED for the status display
2 C14 supply voltage input, 100-230 V, 50/60 Hz
3 Molex socket 24 V DC, 2 A
4 24 V DC output, 2 A (direct connection) (two)
5.2 Installation
• Use the supplied cable to connect the Molex socket with the power pack connection of the
CMC III PU (Fig. 3, Pos. 3).
• If necessary, connect the 24 V output (direct connection) with the appropriate connection of the
CMC III PU (Fig. 3, Pos. 4).
• Observe the pin assignment of the connections:
• Select an appropriate country-specific connection cable for the power pack.
– PE plug and IEC connector connection cable (DK 7200.210)
– CMC IEC extension cable (DK 7200.215)
• Insert the cable in the inlet of the power supply of the power pack and to the mains supply (Fig. 3,
Pos. 2).
• The power pack is operational when the status displays on the CMC III PU and on the power pack
light green continually.
If the installation is not successful: see Section 1.1.
Temperature operational range: +0°C to +40°C
Humidity operational range: 5% to 95% relative humidity, non-condensing
Degree of protection: IP30 in accordance with EN 60 529
Power pack direct connection CMC III PU direct connection
Pin Signal Pin Signal
Pin 1 (left) GND Pin 1 (left) GND
Pin 2 (right) +24 V Pin 2 (centre) +24 V
Pin 3 (right) open
Note:
Other country-specific connection cables can be obtained from Rittal.
Assembly, Installation and operation
EN
7 Rittal CMC III Power Supply
6 Service
For technical questions, please contact:
Tel.: +49 (0) 2772/505-9052
E-mail: [email protected]
Homepage: www.rittal.com
For complaints or service requests, please contact:
Tel.: +49 (0) 2772/505-1855
E-mail: [email protected]
Service
Page is loading ...
Page is loading ...
Page is loading ...
Enclosures
Power Distribution
Climate Control
IT Infrastructure
Software & Services
1. Aufl. 06.2011 / Id.-Nr. A45103 03 IT75
RITTAL GmbH & Co. KG
Postfach 1662
y D-35726 Herborn
Phone +49(0)2772 505-0
y Fax +49(0)2772 505-2319
E-mail: info@rittal.de
y www.rittal.com
/
