NordicTrack NTEL71318.6 User manual

Brand: NordicTrack

Model: NTEL71318.6

Category: Fitness, gymnastics & weight training

Type: User manual

This manual is also suitable for

Freestride Trainer FS7i

USER’S MANUAL

Model No. NTEL71318.6

Serial No.

Write the serial number in the space

above for reference.

nordictrack.com

CAUTION

Read all precautions and

instructions in this manual before

using this equipment. Keep this

manual for future reference.

Serial

Number

Decal

To register your product and

activate your warranty today,

go to my.nordictrack.com.

For service at any time, go to

support.nordictrack.com.

Or call 1-800-TO-BE-FIT

(1-800-862-3348)

Mon.–Fri. 6 a.m.–6 p.m. MT

Sat. 8 a.m.–12 p.m. MT

Please do not contact the store.

ACTIVATE YOUR

WARRANTY

CUSTOMER CARE

TABLE OF CONTENTS

WARNING DECAL PLACEMENT

This drawing shows the location(s) of the warning

decal(s). If a decal is missing or illegible, see

the front cover of this manual and request a

free replacement decal. Apply the decal in the

location shown. Note: The decal(s) may not be

shown at actual size.

WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

IMPORTANT PRECAUTIONS ..................................................................3

BEFORE YOU BEGIN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

PART IDENTIFICATION CHART. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

HOW TO USE THE ELLIPTICAL ..............................................................14

HOW TO USE THE CONSOLE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

FCC INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

MAINTENANCE AND TROUBLESHOOTING .....................................................28

EXERCISE GUIDELINES ....................................................................30

PART LIST. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

EXPLODED DRAWING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33

ORDERING REPLACEMENT PARTS .................................................. Back Cover

LIMITED WARRANTY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover

NORDICTRACK and IFIT are registered trademarks of ICON Health & Fitness, Inc. The Bluetooth

word mark

and logos are registered trademarks of Bluetooth SIG, Inc. and are used under license. Google Maps is a trade-

mark of Google LLC. Wi-Fi is a registered trademark of Wi-Fi Alliance. WPA and WPA2 are trademarks of Wi-Fi

Alliance.

IMPORTANT PRECAUTIONS

WARNING: To reduce the risk of burns, fire, electric shock, or injury to persons, read

all important precautions and instructions in this manual and all warnings on your elliptical before

using your elliptical. ICON assumes no responsibility for personal injury or property damage sus-

tained by or through the use of this product.

1. It is the responsibility of the owner to ensure

that all users of the elliptical are adequately

informed of all precautions.

2. Before beginning any exercise program,

consult your physician. This is especially

important for persons over age 35 or persons

with pre-existing health problems.

3. The elliptical is not intended for use by

persons with reduced physical, sensory, or

mental capabilities or lack of experience and

knowledge, unless they are given supervi-

sion or instruction about use of the elliptical

by someone responsible for their safety.

4. Use the elliptical only as described in this

manual.

5. The elliptical is intended for home use only.

Do not use the elliptical in a commercial,

rental, or institutional setting.

6. Keep the elliptical indoors, away from mois-

ture and dust. Do not put the elliptical in a

garage or covered patio, or near water.

7. Place the elliptical on a level surface, with at

least 4 ft. (1.2 m) of clearance in the front of

the elliptical, 6 ft. (1.8 m) in the rear, and 2 ft.

(0.6 m) on each side. To protect the floor or

carpet from damage, place a mat under the

elliptical.

8. Inspect and properly tighten all parts each

time the elliptical is used. Replace any worn

parts immediately.

9. Keep children under age 16 and pets away

from the elliptical at all times.

10. When connecting the power cord (see

page 14), plug the power cord into a

grounded circuit.

11. Do not modify the power cord or use an

adapter to connect the power cord to an

improper receptacle. Keep the power cord

away from heated surfaces. Do not use an

extension cord.

12. Do not operate the elliptical if the power cord

or plug is damaged, or if the elliptical is not

working properly.

13. DANGER: Always unplug the power

cord and switch the power switch to the off

position when the elliptical is not in use and

before cleaning the elliptical. Servicing other

than the procedures in this manual should be

performed by an authorized service repre-

sentative only.

14. The elliptical should not be used by persons

weighing more than 375 lbs. (170 kg).

15. Wear appropriate clothes while exercising;

do not wear loose clothes that could become

caught on the elliptical. Always wear athletic

shoes for foot protection while exercising.

16. Hold the handlebars when mounting, dis-

mounting, or using the elliptical. Before

mounting or dismounting, bring the pedals

to a stop with the pedal on the mounting or

dismounting side in its lowest position.

17. The elliptical does not have a freewheel; the

pedals will continue to move until the fly-

wheel stops. Reduce your pedaling speed in

a controlled way.

18. Keep your back straight while using the

elliptical; do not arch your back.

19. Over exercising may result in serious injury

or death. If you feel faint, if you become short

of breath, or if you experience pain while

exercising, stop immediately and cool down.

SAVE THESE INSTRUCTIONS

all

STANDARD SERVICE PLANS

Thank you for selecting the revolutionary

NORDICTRACK

FREESTRIDE TRAINER FS7I

elliptical. The FREESTRIDE TRAINER FS7I elliptical

provides an impressive selection of features designed

to make your workouts at home more effective and

enjoyable.

For your benefit, read this manual carefully before

you use the elliptical. If you have questions after

reading this manual, please see the front cover of this

manual. To help us assist you, note the product model

number and serial number before contacting us. The

model number and the location of the serial number

decal are shown on the front cover of this manual.

Before reading further, please familiarize yourself with

the parts that are labeled in the drawing below.

Handlebar

Fan

Accessory Tray

Console

BEFORE YOU BEGIN

Wheel

Leveling Foot

Power Cord

Length: 4 ft. 11 in. (150 cm)

Width: 2 ft. 6 in. (76 cm)

Pedal

PART IDENTIFICATION CHART

Use the drawings below to identify the small parts needed for assembly. The number in parentheses below each

drawing is the key number of the part, from the PART LIST near the end of this manual. The number following the

key number is the quantity needed for assembly. Note: If a part is not in the hardware kit, check to see if it

has been preassembled. Extra parts may be included.

M10 Locknut

(133)–2

M10 x 18mm

Washer (138)–4

Axle Washer

(31)–2

M8 x 14mm

Shoulder Screw

(122)–2

M4 x 16mm

Screw

(143)–22

M6 x 20mm

Screw

(118)–6

M4 x 10mm

Screw

(148)–2

M10 x 25mm Screw

(123)–8

M10 x 45mm Bolt

(119)–4

M10 x 45mm Screw

(124)–4

M10 x 70mm Bolt (130)–2

• Assembly requires two or three persons.

• Place all parts in a cleared area and remove the

packing materials. Do not dispose of the packing

materials until you nish all assembly steps.

• Left parts are marked “L” or “Left” and right parts

are marked “R” or “Right.”

• To identify small parts, see page 7.

• In addition to the included tool(s), assembly

requires the following tools:

one Phillips screwdriver

one adjustable wrench

one rubber mallet

Assembly may be easier if you have a set of

wrenches. To avoid damaging parts, do not use

power tools.

ASSEMBLY

1. Go to my.nordictrack.com on your computer

and register your product.

• documents your ownership

• activates your warranty

• ensures priority customer support if assistance

is ever needed

Note: If you do not have internet access, call

Customer Care (see the front cover of this

manual) and register your product.

130

133

2. Attach a Wheel (53) to one side of the Stabilizer

(3) with an M10 x 70mm Bolt (130) and an M10

Locknut (133); do not overtighten the Locknut;

the Wheel should turn freely.

Attach the other Wheel (53) in the same way.

3. Tip: Avoid pinching the wires. With the help of

one or two other people, set the Upright (4) on

the pins (A) on the Frame (2).

Attach the Upright (4) with eight M10 x 25mm

Screws (123); start all the Screws, and then

tighten them.

Then, connect the 41" Wire (52) in the Upright

(4) to the 17" Wire (51) in the Frame (2).

4. Identify the Right Shield Cover (36) and the

Right Front Shield Cover (47). Attach them

around the right side of the Upright (4) with

two M4 x 16mm Screws (143). Then, press the

Shield Covers into place.

Tip: Avoid pinching the wires. Attach the Left

Shield Cover (35) and the Left Front Shield

Cover (43) around the left side of the Upright

(4) in the same way.

143

123

Avoid

pinching

the wires

Avoid

pinching

the wires

122

Grease

118

5. Identify the Right Pedal Arm (15). Using a plastic

bag to keep your fingers clean, apply a generous

amount of the included grease to the axle on the

Right Pedal Arm.

Insert the axle on the Right Pedal Arm (15)

into the Right Pivot Leg (13) from the direction

shown.

Attach the Right Pedal Arm (15) with an

M8 x 14mm Shoulder Screw (122), an Axle

Cover (30), and an Axle Washer (31).

Attach the Left Pedal Arm (14) to the Left

Pivot Leg (12) in the same way.

6. Identify the Strap (21) on the Right Pedal Arm

(15). Route the Strap under the Roller (89);

make sure that the Strap is not twisted.

Make sure that the Glide Belt (19) on the

Right Pedal Arm (15) is resting on top of the

Roller (89) and that the Strap (21) is routed

under the Roller.

Tip: It may be helpful to have a second

person press downward on the Right Pedal

Arm (15) while you perform the following

action.

Make sure to orient the Strap Clamp (23) as

shown in the inset drawing. Attach the Strap

(21) to the Strap Bracket (22) on the Right Pedal

Arm (15) with three M6 x 20mm Screws (118)

and a Strap Clamp; start all the Screws, and

then tighten them.

Repeat this step for the Left Pedal Arm (14).

143

119

138

8. See the inset drawing. Identify a Handlebar

Cover (40) and the Right Rear Leg Cover (44),

and slide them onto a Handlebar (16) as shown.

Insert the Handlebar (16) into the Right Pivot

Leg (13), and attach it with two M10 x 45mm

Bolts (119) and two M10 x 18mm Washers (138).

Press the Right Rear Leg Cover (44) into place.

Then, press the Handlebar Cover (40) into place.

Repeat this step on the other side of the

elliptical.

7. Identify the Left and Right Rear Belt Covers

(24, 25), and then attach them to the Left Pedal

Arm (14) with five M4 x 16mm Screws (143);

start all the Screws, and then tighten them.

Repeat this step on the other side of the

elliptical.

124

148

143

111

9. Attach the Accessory Tray (111) to the

Upright (4) from below with two M4 x 16mm

Screws (143).

Then, attach the Accessory Tray (111) to the

Upright (4) from above with two M4 x 10mm

Screws (148).

10. While a second person holds the Console

Bracket (5) near the Upright (4), insert the 32"

Wire (58) upward through the hole in the side of

the Console Bracket as shown.

Tip: Avoid pinching the wires. Attach the

Console Bracket (5) to the Upright (4) with

four M10 x 45mm Screws (124); start all the

Screws, and then tighten them.

11. While a second person holds the Console (9)

near the Console Bracket (5), connect the wires

(B) on the Console to the matching wires (C) in

the Console Bracket; make sure to press the

connectors on the wires together firmly.

Insert the excess wire into the Console

Bracket (5).

Avoid pinching

the wires

14. Make sure that all parts are properly tightened before you use the elliptical. Extra parts may be included.

Place a mat beneath the elliptical to protect the floor.

143

13. Tip: Avoid pinching the wires. Attach the

Console Bracket Cover (48) to the Accessory

Tray (111) with two M4 x 16mm Screws (143).

Avoid pinching

the wires

12. Tip: Avoid pinching the wires. Attach the

Console (9) to the Console Bracket (5) with four

M4 x 16mm Screws (143); start all the Screws,

and then tighten them.

Avoid pinching

the wires

111

143

HOW TO USE THE ELLIPTICAL

HOW TO PLUG IN THE POWER CORD

This product must be grounded. If it should mal-

function or break down, grounding provides a path of

least resistance for electric current to reduce the risk

of electric shock. The power cord has a plug with a

grounding pin.

Plug the power

cord (A) into

an appropriate

outlet (B) that is

properly installed

and grounded in

accordance with

all local codes and

ordinances. The

outlet must be

on a nominal 120-volt circuit.

A temporary

adapter (C) may

be used to con-

nect the power

cord to a 2-pole

receptacle (D)

as shown at the

right if a properly

grounded outlet is

not available.

The lug (E) or wire extending from the adapter must

be connected with a metal screw (F) to a permanent

ground such as a properly grounded outlet box cover.

Some 2-pole receptacle outlet box covers are not

grounded. Before using an adapter, contact a

qualied electrician to determine whether the out-

let box cover is grounded before using an adapter.

The temporary adapter should be used only until

a properly grounded outlet can be installed by a

qualied electrician.

DANGER: Improper connection of

the power cord increases the risk of electric

shock. Do not modify the plug—if it will not fit

an outlet, have a proper outlet installed by a

qualified electrician. If you are unsure whether

the product is properly grounded, contact a

qualified electrician.

HOW TO MOVE THE ELLIPTICAL

Due to the size and weight of the elliptical, moving

it requires two persons. Stand in front of the ellipti-

cal and lift the handle (G) until the elliptical will roll on

the wheels. Carefully move the elliptical to the desired

location, and then lower it to the floor.

HOW TO EXERCISE ON THE ELLIPTICAL

To mount the elliptical, hold the handlebars (H) and

step onto the pedal (I) that is in the lower position.

Then, step onto the other pedal. Push the pedals until

they begin to move with a continuous motion. Note:

The pedals can turn in either direction. It is recom-

mended that you turn the pedals in the direction

shown by the arrow; however, for variety, you can

turn the pedals in the opposite direction.

To dismount the elliptical, wait until the pedals (I) come

to a complete stop. Note: The elliptical does not

have a freewheel; the pedals will continue to move

until the flywheel stops. When the pedals are station-

ary, step off the higher pedal first. Then, step off the

lower pedal.

HOW TO LEVEL THE ELLIPTICAL

If the elliptical rocks

slightly on your

floor during use,

turn one or both of

the leveling feet (J)

beneath the front of

the frame until the

rocking motion is

eliminated.

THE OPTIONAL TABLET HOLDER

The optional tablet

holder (K) will hold

your tablet securely

in place and enable

you to use your tablet

while you exercise. The

optional tablet holder is

designed for use with

most full-size tablets.

To purchase a tablet

holder, please see

the front cover of this

manual.

Rafe

ELNT71318

NTEL71318.2

CONSOLE DIAGRAM

FEATURES OF THE CONSOLE

The advanced console offers an array of features

designed to make your workouts more effective and

enjoyable.

The console features wireless technology that enables

the console to connect to iFit. With iFit, you can access

a large and varied workout library, create your own

workouts, track your workout results, and access many

other features.

In addition, the console features a selection of onboard

workouts. Each workout automatically controls the

resistance of the pedals and the incline of the frame as

it guides you through an effective exercise session.

When you use the manual mode of the console, you

can change the resistance of the pedals and the incline

of the frame with the touch of a button.

While you exercise, the console will display continuous

exercise feedback. You can even measure your heart

rate using a compatible heart rate monitor.

You can also listen to your favorite workout music or

audio books with the console sound system while you

exercise.

To turn on the power, see page 18. To learn how

to use the touch screen, see page 18. To set up

the console, see page 18.

HOW TO USE THE CONSOLE

HOW TO TURN ON THE POWER

IMPORTANT: If the elliptical has been exposed to

cold temperatures, allow it to warm to room tem-

perature before you turn on the power. If you do

not do this, you may damage the console or other

electrical components.

Plug in the power cord (see

HOW TO PLUG IN THE POWER

CORD on page 14). Next,

locate the power switch on the

frame near the power cord.

Press the power switch to the

reset position (A).

The console will then turn on and be ready for use.

Note: When you turn on the power for the rst time,

the incline system may calibrate automatically. The

frame will move upward and downward as it calibrates.

When the frame stops moving, the incline system is

calibrated.

IMPORTANT: If the incline system does not

calibrate automatically, see step 6 on page 18

and manually calibrate the incline system.

HOW TO USE THE TOUCH SCREEN

The console features a tablet with a full-color touch

screen. The following information will help you use the

touch screen:

• The console functions similarly to other tablets. You

can slide or flick your finger against the screen to

move certain images on the screen, such as the

displays in a workout.

• To type information into a text box, first touch the text

box to view the keyboard. To use numbers or other

characters on the keyboard, touch ?123. To view

more characters, touch ~[<. Touch ?123 again to

return to the number keyboard. To return to the letter

keyboard, touch ABC. To use a capital character,

touch the shift button (upward-facing arrow symbol).

To use multiple capital characters, touch the shift

button again. To return to the lowercase keyboard,

touch the shift button a third time. To clear the last

character, touch the clear button (backward-facing

arrow with an X symbol).

HOW TO SET UP THE CONSOLE

Before you use the elliptical for the first time, set up the

console.

1. Connect to your wireless network.

To use iFit workouts and to use several other

features of the console, the console must be con-

nected to a wireless network. Follow the prompts

on the screen to connect the console to your wire-

less network.

2. Customize settings.

Follow the prompts on the screen to set the desired

unit of measurement and your time zone.

Note: To change these settings later, see HOW TO

CHANGE CONSOLE SETTINGS on page 24.

3. Log into or create an iFit account.

Follow the prompts on the screen to log into your

iFit account or to create an iFit account.

4. Tour the console.

The first time you use the console, a tour

presentation will guide you through the features of

the console.

5. Check for firmware updates.

First, touch the menu button (three horizontal lines

symbol), touch Settings, touch Maintenance, and

then touch Update. The console will check for firm-

ware updates. For more information, see HOW TO

CHANGE CONSOLE SETTINGS on page 24.

6. Calibrate the incline system.

First, touch the menu button (three horizontal lines

symbol), touch Settings, touch Maintenance, and

then touch Calibrate Incline. The frame will rise

and lower as it calibrates. For more information,

see HOW TO CHANGE CONSOLE SETTINGS on

page 24.

The console is now ready for you to begin working out.

The following pages explain the workouts and other

features that the console offers.

To use the manual mode, see page 19. To use

a featured workout or an onboard workout, see

page 20. To create a draw-your-own-map work-

out, see page 22. To use an iFit workout, see

page 23.

To change console settings, see page 24. To

connect to a wireless network, see page 25. To

use the sound system, see page 26.

Note: If there is a sheet of plastic on the screen,

remove the plastic.

HOW TO USE THE MANUAL MODE

1. Touch the screen or press any button on the

console to turn on the console.

See HOW TO TURN ON THE POWER on

page 18. Note: It may take a few moments for

the console to be ready for use.

2. Select the main menu.

When you turn on the console, the main menu will

appear on the screen after the console boots up.

If you are in a workout, touch the screen and follow

the prompts to end the workout and return to the

main menu. If you are in the settings menus, touch

the back button (arrow symbol) and then touch the

close button (x symbol) to return to the main menu.

3. Change the resistance of the pedals and the

incline of the frame as desired.

Touch Manual Start and begin pedaling.

You can change the resistance of the pedals by

pressing one of the numbered Quick Resistance

buttons or by pressing the Resistance increase and

decrease buttons.

To vary the motion of the pedals, you can change

the incline of the frame by pressing one of the

numbered Quick Incline buttons or by pressing the

Incline increase and decrease buttons.

Note: After you press a button, it will take a

moment for the pedals to reach the selected

resistance level or for the frame to reach the

selected incline level.

4. Follow your progress.

The console offers several display modes. The

display mode that you select will determine which

workout information is shown.

Drag upward on the screen to enter the fullscreen

display mode. Drag downward on the screen to

view the workout information displays.

Touch the various workout information displays

to view more options. Touch the more button

(+ symbol) to view statistics or charts. Touch the

center of the screen to view even more display

mode options.

If desired, adjust the

volume level by pressing

the volume increase and

decrease buttons on the

console.

To pause the workout, simply touch the screen

or stop pedaling. To continue the workout, simply

resume pedaling.

To end the workout session, touch the screen to

pause the workout, and then follow the prompts

on the screen to end the workout and return to the

main menu.

5. Wear a compatible heart rate monitor and

measure your heart rate if desired.

You can wear a compatible heart rate monitor to

measure your heart rate. Note: The console is

compatible with all Bluetooth

Smart heart rate

monitors.

A compatible chest heart rate monitor is included

with some models. If a chest heart rate monitor

is included, see THE CHEST HEART RATE

MONITOR in this manual to learn how to use it.

If this model does not include a compatible heart

rate monitor, see page 26 for information about

ordering one.

The console will connect to your compatible heart

rate monitor automatically. When your heartbeat is

detected, your heart rate will be shown.

6. Turn on the fan if desired.

The fan has several speed

settings, including an auto

mode. While the auto mode

is selected, the speed of

the fan will automatically

increase or decrease as your pedaling speed

increases or decreases. Press the fan increase and

decrease buttons repeatedly to select a fan speed

or to turn off the fan.

Note: If the pedals are not moved for a while when

the main menu is selected, the fan will turn off

automatically.

7. When you are finished exercising, unplug the

power cord.

When you are finished exercising, press the power

switch to the off position and unplug the power

cord. IMPORTANT: If you do not do this, the

electrical components of the elliptical may wear

prematurely.

HOW TO USE A FEATURED WORKOUT OR AN

ONBOARD WORKOUT

1. Touch the screen or press any button on the

console to turn on the console.

See HOW TO TURN ON THE POWER on

page 18. Note: It may take a few moments for

the console to be ready for use.

2. Select the main menu or the workout library.

When you turn on the console, the main menu will

appear on the screen after the console boots up.

If you are in a workout, touch the screen and follow

the prompts to end the workout and return to the

main menu. If you are in the settings menus, touch

the back button (arrow symbol) and then touch the

close button (x symbol) to return to the main menu.

Touch the buttons at the bottom of the screen to

select either the main menu (Home button) or the

workout library (Browse button).

3. Select a workout.

To select a workout from the main menu or the

workout library, simply touch the desired workout

button on the screen. Slide or flick the screen to

scroll upward or downward if necessary.

Note: To use a featured workout, the console must

be connected to a wireless network (see HOW

TO CONNECT TO A WIRELESS NETWORK on

page 25).

The featured workouts on your console will change

periodically. To save one of the featured workouts

for future use, you can add it as a favorite by touch-

ing the favorites button (heart symbol). You must

be logged into your iFit account to save a featured

workout (see step 3 on page 23).

Page is loading ...

NordicTrack NTEL71318.6 User manual

Brand: NordicTrack

Model: NTEL71318.6

Category: Fitness, gymnastics & weight training

Type: User manual

This manual is also suitable for

Freestride Trainer FS7i

Download PDF

report

NordicTrack NTEL71318.6 User manual

This manual is also suitable for

NordicTrack NTEL71318.6 User manual

Related papers

Other documents