Empire INTERMITTENT PILOT DVCD36FP71P-1 Installation Instructions And Owner's Manual

Page 1

This appliance may be installed in

an aftermarket, permanently located,

manufactured home (USA only) or mobile

home, where not prohibited by state or

local codes.

This appliance is only for use with the type

of gas indicated on the rating plate. This

appliance is not convertible for use with

other gases, unless a certied kit is used.

NOTE: Barrier required, but may be sold separately.

HOT GLASS

DO NOT TOUCH

NEVER

WILL

CAUSE BURNS.

GLASS

UNTIL COOLED.

ALLOW CHILDREN

TO TOUCH GLASS.

WARNING

A barrier designed to reduce the risk of burns from the

hot viewing glass is provided with this appliance and shall

be installed for the protection of children and other at-risk

individuals.

INSTALLATION INSTRUCTIONS

AND OWNER’S MANUAL

WARNING

FIRE OR EXPLOSION HAZARD

If the information in this manual is not

followed exactly, a re or explosion may

result causing property damage, personal

injury or loss of life.

— Do not store or use gasoline or other

ammable vapors and liquids in the

vicinity of this or any other appliance.

— WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do

not use any phone in your building.

• Leave the building immediately.

• Immediately call your gas supplier

from a neighbor’s phone. Follow the

gas supplier’s instructions.

• If you cannot reach your gas supplier,

call the re department.

— Installation and service must be

performed by a qualied installer,

service agency or the gas supplier.

INSTALLER:

Leave this manual with the appliance.

CONSUMER:

Retain this manual for future reference.

DIRECT VENT

ZERO CLEARANCE GAS

FIREPLACE HEATER SERIES:

MILLIVOLT (MV)

DVCD(32,36,42)FP30(N,P)-1

DIRECT IGNITION (DI)

DVCD(32,36,42)FP50N-1

INTERMITTENT PILOT (IP)

DVCD(32,36,42)FP7(0,1)(N,P)-1

UL FILE NO. MH30033

GAS-FIRED

WARNING

If not installed, operated and maintained

in accordance with the manufacturer’s

instructions, this product could expose you

to substances in fuel or from fuel combustion

which can cause death or serious illness.

CARTON CONTENTS

Accessory Sheet Rockwool

Hardware Pack Registration Card

AA Battery (4) (IP only) Power Adaptor (IP only)

Junction Box Cover Receptical

Logs Decorative Rocks

31509-13-0416Page 2

TABLE OF CONTENTS

IMPORTANT SAFETY INFORMATION ........................................................................................................................ 3

SAFETY INFORMATION FOR USERS OF LP GAS.................................................................................................... 4

REQUIREMENTS FOR MASSACHUSETTS ............................................................................................................... 5

INTRODUCTION .......................................................................................................................................................... 6

SPECIFICATIONS ........................................................................................................................................................ 7

VENT SYSTEM IDENTIFICATION ............................................................................................................................... 8

SPECIAL VENT SYSTEMS ......................................................................................................................................... 8

FIREPLACE DIMENSIONS ......................................................................................................................................... 9

CLEARANCES ........................................................................................................................................................... 10

LOCATING FIREPLACE .............................................................................................................................................11

GAS SUPPLY ............................................................................................................................................................. 12

INSTALLATION ..................................................................................................................................................... 13-17

VENTING FIREPLACE - TOP ............................................................................................................................... 18-20

EXAMPLES - TOP VENT RUN .................................................................................................................................. 21

VENTING FIREPLACE - REAR ................................................................................................................................. 22

EXAMPLES - REAR VENT RUN ............................................................................................................................... 23

REAR VENT CONVERSION ...................................................................................................................................... 24

VENT CLEARANCES ................................................................................................................................................ 25

FRAMING AND FINISHING .................................................................................................................................. 26-27

TERMINATION CLEARANCES ................................................................................................................................. 28

HORIZONTAL TERMINATION ................................................................................................................................... 29

VERTICAL TERMINATION ................................................................................................................................... 30-31

DVVK-4F FLEX VENT INSTRUCTIONS .................................................................................................................... 32

DVVK-4RE VENT KIT INSTALLATION INSTRUCTIONS ..................................................................................... 33-35

DVCD32 LOG IDENTIFICATION ............................................................................................................................... 36

LOG PLACEMENT - 32” FIREPLACES ................................................................................................................ 37-45

DVCD36 LOG IDENTIFICATION ............................................................................................................................... 46

LOG PLACEMENT - 36” FIREPLACES ................................................................................................................ 47-54

DVCD42 LOG IDENTIFICATION ............................................................................................................................... 55

LOG PLACEMENT - 42” FIREPLACES ................................................................................................................ 56-64

MILLIVOLT OPERATING INSTRUCTIONS (FP3 SERIES) .................................................................................. 65-66

MILLIVOLT STANDING PILOT WIRING DIAGRAM (FP3 SERIES) .......................................................................... 67

MILLIVOLT STANDING PILOT LIGHTING INSTRUCTIONS (FP3 SERIES) ............................................................ 68

MILLIVOLT STANDING PILOT TROUBLESHOOTING (FP3 SERIES) ..................................................................... 69

DIRECT IGNITION LIGHTING INSTRUCTIONS (FP5 SERIES) ............................................................................... 70

DIRECT IGNITION WIRING DIAGRAM (FP5 SERIES) ............................................................................................. 71

OPTIONAL REMOTE CONTROL .............................................................................................................................. 72

INITIAL START UP GAS LINE PURGE (FP5 SERIES) ............................................................................................. 72

DIRECT IGNITION TROUBLESHOOTING ................................................................................................................ 72

DIRECT IGNITION PROPANE/LP GAS CONVERSION (FP5 SERIES) ................................................................... 73

PROPANE/LP GAS CONVERSION (FP5 SERIES) ................................................................................................... 74

IPI ELECTRONIC SYSTEM OPERATING INSTRUCTIONS (FP7 SERIES) ............................................................. 75

IPI ELECTRONIC SYSTEM WIRING DIAGRAM (FP7 SERIES)............................................................................... 76

INTERMITTENT PILOT LIGHTING INSTRUCTIONS (FP7 SERIES) ....................................................................... 77

INTERMITTENT PILOT CONTROL SYSTEM TROUBLESHOOTING (FP7 SERIES) ......................................... 78-80

MAINTENANCE AND SERVICE ................................................................................................................................ 81

DVCD32FP(3,5,7) PARTS LIST ................................................................................................................................. 82

DVCD32FP(3,5,7) PARTS VIEW ............................................................................................................................... 83

DVCD36FP(3,5,7) PARTS LIST ................................................................................................................................. 84

DVCD36FP(3,5,7) PARTS VIEW ............................................................................................................................... 85

DVCD42FP(3,5,7) PARTS LIST ................................................................................................................................. 86

DVCD42FP(3,5,7) PARTS VIEW ............................................................................................................................... 87

FBB4 OPTIONAL VARIABLE SPEED BLOWER INSTALLATION ........................................................................ 88-89

MASTER PARTS DISTRIBUTOR LIST ...................................................................................................................... 90

HOW TO ORDER REPAIR PARTS ............................................................................................................................ 90

JUNCTION BOX WIRING INSTALLATION INSTRUCTIONS .................................................................................... 91

OPTIONAL BRICK LINER INSTALLATION INSTRUCTIONS .................................................................................... 92

ACCESSORIES ......................................................................................................................................................... 92

DECORATIVE ACCESORIES .................................................................................................................................... 93

WARRANTY ............................................................................................................................................................... 94

APPLIANCE SERVICE HISTORY .............................................................................................................................. 95

SECTION PAGE

31509-13-0416 Page 3

DO NOT OPERATE THIS APPLIANCE WITHOUT GLASS FRONT PANEL INSTALLED

Before enclosing the vent pipe assembly, operate the appliance to ensure it is venting properly.

• Due to high temperatures the appliance should be

located out of trafc and away from furniture and

draperies.

• The glass front or any part removed for servicing

the appliance must be replaced prior to operating

the appliance. Work should be done by a qualied

service person.

• Keep burner and control compartment clean.

• Vent cap is hot while replace is in operation.

• Installation and repair should be done by a

QUALIFIED SERVICE PERSON. The appliance

should be inspected before use and at least annually

by a qualified service person. More frequent

cleaning may be required due to excessive lint from

carpeting, bedding materials, etc. It is imperative

that control compartments, burners and circulating

air passageways of the appliance be kept clean.

• DO NOT put anything around the replace that will

obstruct the ow of ventilation air.

• Clearance in accordance with local installation

codes and the requirements of the gas supplier.

• DO keep the appliance area clear and free from

combustible material, gasoline and other ammable

vapors and liquids.

• DO examine venting system periodically and replace

damaged parts.

• DO make a periodic visual check of pilot and burners.

Clean and replace damaged parts.

• CAUTION: The glass used in your replace is

tempered glass. If the glass is cracked or damaged in

any way, it should be replaced only with a complete

glass frame assembly from Empire. See parts list

on Pages 56 - 61 for ordering.

• DO NOT use this replace if any part has been under

water. Immediately call a qualied service technician

to inspect the heater and to replace any part of the

control system and any gas control which has been

under water.

• Any safety screen or guard removed for servicing

an appliance must be replaced prior to operating

the appliance.

• If this appliance is installed directly on carpeting,

tile or other combustible material other than wood

ooring the appliance shall be installed on a metal

or wood panel extending the full width and depth

of the appliance.

The base referred to above does not mean the

fireproof base as used on wood stoves. The

protection is for rugs that are extremely thick and

light colored tile.

• Children and adults should be alerted to the hazards

of high surface temperatures and should stay away

to avoid burns or clothing ignition.

• Young children should be carefully supervised when

they are in the same room as the appliance.

• Clothing or other ammable material should not be

placed on or near the appliance.

• Adequate accessibility clearances for servicing and

proper operation.

• This appliance must not share or be connected to a

ue serving a separate solid-fuel burning appliance.

• Keep the area around your appliance clear of

combustible materials, gasoline and other ammable

vapor and liquids.

• Under no circumstances should any solid fuels

(wood, coal, paper or cardboard etc.) be used in

this appliance.

• The ow of combustion and ventilation air must not

be obstructed in any way.

• Young children should be carefully supervised

when they are in the same room as the appliance.

Toddlers, young children, and others may be sus-

ceptible to accidental contact burns. A physical

barrier is recommended if there are at-risk individ-

uals in the house. To restrict access to a replace

or stove, install an adjustable safety gate to keep

toddlers young children, and other at-risk individ-

uals out of the room and away from hot surfaces.

• A barrier designed to reduce the risk of burns from

the hot viewing glass is provided with this appli-

ance and shall be installed for the protection of

children and other at-risk individuals. Barrier re-

quired, but may be sold separately.

• If the barrier becomes damaged, the barrier shall

be replaced with the manufacturer’s barrier for

this appliance.

• Any safety screen, guard, or barrier removed for

servicing an appliance must be replaced prior to

operating the appliance.

IMPORTANT SAFETY INFORMATION

31509-13-0416Page 4

SAFETY INFORMATION FOR USERS OF LP GAS

Propane (LP-Gas) is a ammable gas which can cause

res and explosions. In its natural state, propane is

odorless and colorless. You may not know all the fol-

lowing safety precautions which can protect both you

and your family from an accident. Read them carefully

now, then review them point by point with the mem-

bers of your household. Someday when there may not

be a minute to lose, everyone’s safety will depend on

knowing exactly what to do. If, after reading the follow-

ing information, you feel you still need more informa-

tion, please contact your gas supplier.

LP-GAS WARNING ODOR

If a gas leak happens, you should be able to smell the

gas because of the odorant put in the LP-Gas. That’s

your signal to go into immediate action!

• Donotoperateelectricswitches,lightmatches,use

yourphone.Donotdoanythingthatcouldignitethe

gas.

• Geteveryoneoutofthebuilding,vehicle,trailer,or

area.DothatIMMEDIATELY.

• Closeallgastankorcylindersupplyvalves.

• LP-Gasisheavierthanairandmaysettleinlowareas

suchasbasements.Whenyouhavereasontosuspect

agasleak,keepoutofbasementsandotherlowar-

eas.Stayoutuntilreghtersdeclarethemtobesafe.

• Useyourneighbor’sphoneandcallatrainedLP-Gas

servicepersonandtheredepartment.Eventhough

youmaynotcontinuetosmellgas,donotturnonthe

gasagain.Donotre-enterthebuilding,vehicle,trailer,

or area.

• Finally,lettheservicemanandreghterscheckfor

escapedgas.Havethemairouttheareabeforeyou

return.ProperlytrainedLP-Gasservicepeopleshould

repairtheleak,thencheckandrelightthegasappli-

anceforyou.

NO ODOR DETECTED - ODOR FADE

Some people cannot smell well. Some people cannot

smell the odor of the chemical put into the gas. You

must nd out if you can smell the odorant in propane.

Smokingcandecreaseyourabilitytosmell.Beingaround

anodorforatimecanaffectyoursensitivityorabilityto

detectthatodor.Sometimesotherodorsintheareamask

thegasodor.Peoplemaynotsmellthegasodorortheir

mindsareonsomethingelse.Thinkingaboutsmellinga

gasodorcanmakeiteasiertosmell.

The odorant in LP-Gas is colorless, and it can fade

under some circumstances.Forexample,ifthereisan

undergroundleak,themovementofthegasthroughsoil

canltertheodorant.OdorantsinLP-Gasalsoaresubject

tooxidation.Thisfadingcanoccurifthereisrustinsidethe

storagetankorinirongaspipes.

Theodorantinescapedgascanadsorborabsorbonto

orintowalls,masonryandothermaterialsandfabricsin

aroom.Thatwilltakesomeoftheodorantoutofthegas,

reducingitsodorintensity.

LP-Gasmaystratifyinaclosedarea,andtheodorintensi-

tycouldvaryatdifferentlevels.Sinceitisheavierthanair,

theremaybemoreodoratlowerlevels.Alwaysbesensi-

tivetotheslightestgasodor.Ifyoudetectanyodor,treatit

asaseriousleak.Immediatelygointoactionasinstructed

earlier.

SOME POINTS TO REMEMBER

• Learn to recognize the odor of LP-Gas.Yourlocal

LP-GasDealercangiveyoua“ScratchandSniff”

pamphlet.Useittondoutwhatthepropaneodor

smellslike.IfyoususpectthatyourLP-Gashasa

weakorabnormalodor,callyourLP-GasDealer.

• Ifyouarenotqualied,donotlightpilotlights,perform

service,ormakeadjustmentstoappliancesonthe

LP-Gassystem.Ifyouarequalied,consciouslythink

abouttheodorofLP-Gaspriortoandwhilelightingpi-

lotlightsorperformingserviceormakingadjustments.

• Sometimesabasementoraclosed-uphousehasa

mustysmellthatcancoveruptheLP-Gasodor.Donot

trytolightpilotlights,performservice,ormakeadjust-

mentsinanareawheretheconditionsaresuchthat

youmaynotdetecttheodoriftherehasbeenaleakof

LP-Gas.

• Odorfade,duetooxidationbyrustoradsorptionon

wallsofnewcylindersandtanks,ispossible.There-

fore,peopleshouldbeparticularlyalertandcareful

whennewtanksorcylindersareplacedinservice.

Odorfadecanoccurinnewtanks,orreinstalledold

tanks,iftheyarelledandallowedtosettoolongbe-

forerelling.Cylindersandtankswhichhavebeenout

ofserviceforatimemaydevelopinternalrustwhich

willcauseodorfade.Ifsuchconditionsaresuspected

toexist,aperiodicsnifftestofthegasisadvisable.

If you have any question about the gas odor, call

your LP-Gas dealer. A periodic sniff test of the LP-

Gas is a good safety measure under any condition.

• If,atanytime,youdonotsmelltheLP-Gasodorant

andyouthinkyoushould,assumeyouhavealeak.

Thentakethesameimmediateactionrecommended

abovefortheoccasionwhenyoudodetecttheodor-

ized LP-Gas.

• Ifyouexperienceacomplete“gasout,”(thecontainer

isundernovaporpressure),turnthetankvalveoff

immediately.Ifthecontainervalveislefton,thecon-

tainermaydrawinsomeairthroughopeningssuch

aspilotlightorices.Ifthisoccurs,somenewinternal

rustingcouldoccur.Ifthevalveisleftopen,thentreat

thecontainerasanewtank.Alwaysbesureyourcon-

tainerisundervaporpressurebyturningitoffatthe

containerbeforeitgoescompletelyemptyorhavingit

relledbeforeitiscompletelyempty.

31509-13-0416 Page 5

REQUIREMENTS FOR MASSACHUSETTS

Forallsidewallhorizontallyventedgasfueledequipment

installedineverydwelling,buildingorstructureusedin

wholeorinpartforresidentialpurposes,includingthose

ownedoroperatedbytheCommonwealthandwherethe

sidewallexhaustventterminationislessthansevenfeet

abovenishedgradeintheareaoftheventing,including

butnotlimitedtodecksandporches,thefollowing

requirementsshallbesatised:

1. INSTALLATION OF CARBON MONOXIDE

DETECTORS.Atthetimeofinstallationoftheside

wallhorizontalventedgasfueledequipment,the

installingplumberorgasttershallobservethatahard

wiredcarbonmonoxidedetectorwithanalarmand

batteryback-upisinstalledontheoorlevelwhere

thegasequipmentistobeinstalled.Inaddition,

theinstallingplumberorgasttershallobservethat

abatteryoperatedorhardwiredcarbonmonoxide

detectorwithanalarmisinstalledoneachadditional

levelofthedwelling,buildingorstructureservedby

thesidewallhorizontalventedgasfueledequipment.

Itshallbetheresponsibilityofthepropertyownerto

securetheservicesofqualiedlicensedprofessionals

fortheinstallationofhardwiredcarbonmonoxide

detectors

 a. Intheeventthatthesidewallhorizontallyvented

gasfueledequipmentisinstalledinacrawlspace

oranattic,thehardwiredcarbonmonoxide

detectorwithalarmandbatteryback-upmaybe

installedonthenextadjacentoorlevel.

 b. Intheeventthattherequirementsofthis

subdivisioncannotbemetatthetimeof

completionofinstallation,theownershallhave

aperiodofthirtydaystocomplywiththeabove

requirements;provided,however,thatduring

saidthirtydayperiod,abatteryoperatedcarbon

monoxidedetectorwithanalarmshallbeinstalled.

2. APPROVED CARBON MONOXIDE DETECTORS.

Eachcarbonmonoxidedetectorasrequiredin

accordancewiththeaboveprovisionsshallcomply

withNFPA720andbeANSI/UL2034listedandIAS

certied.

3. SIGNAGE.Ametalorplasticidenticationplate

shallbepermanentlymountedtotheexteriorofthe

buildingataminimumheightofeightfeetabove

gradedirectlyinlinewiththeexhaustventterminalfor

thehorizontallyventedgasfueledheatingappliance

orequipment.Thesignshallread,inprintsizeno

lessthan1/2inchinsize,“GAS VENT DIRECTLY

BELOW. KEEP CLEAR OF ALL OBSTRUCTIONS”.

4. INSPECTION.Thestateorlocalgasinspectorofthe

sidewallhorizontallyventedgasfueledequipment

shallnotapprovetheinstallationunless,upon

inspection,theinspectorobservescarbonmonoxide

detectorsandsignageinstalledinaccordancewiththe

provisionsof248CMR5.08(2)(a)1through4.

 (b) EXEMPTIONS:Thefollowingequipmentisexempt

from248CMR5.08(2)(a)1through4:

  1. TheequipmentlistedinChapter10entitled

“EquipmentNotRequiredToBeVented”inthe

mostcurrenteditionofNFPA54asadoptedby

theBoard;and

  2. ProductApprovedsidewallhorizontallyvented

gasfueledequipmentinstalledinaroomor

structureseparatefromthedwelling,building

orstructureusedinwholeorinpartfor

residentialpurposes.

(d) MANUFACTURER REQUIREMENTS - GAS

EQUIPMENT VENTING SYSTEM NOT

PROVIDED.WhenthemanufacturerofaProduct

Approvedsidewallhorizontallyventedgasfueled

equipmentdoesnotprovidethepartsforventing

theuegases,butidenties“specialventing

systems”,thefollowingrequirementsshallbe

satisedbythemanufacturer:

  1. Thereferenced“specialventingsystem”

instructionsshallbeincludedwiththe

applianceorequipmentinstallation

instructions;and

  2. The“specialventingsystems”shallbeProduct

ApprovedbytheBoard,andtheinstructions

forthatsystemshallincludeapartslistand

detailedinstallationinstruction.

 (e) AcopyofallinstallationinstructionsforallProduct

Approvedsidewallhorizontallyventedgasfueled

equipment,allventinginstructions,allpartslists

forventinginstructions,and/orallventingdesign

instructionsshallremainwiththeapplianceor

equipmentatthecompletionoftheinstallation.

31509-13-0416Page 6

Instructions to Installer

1. Installermustleaveinstructionmanualwithowner

afterinstallation.

2. Installermusthaveownerlloutandmailwarranty

cardsuppliedwiththereplace.

3. Installershouldshowownerhowtostartandoperate

thereplace.

Thisdirectventgasreplaceheaterisdesignedtooperate

withallcombustionairbeingsiphonedfromtheoutsideof

thebuildingandallexhaustgasesexpelledtotheoutside

ofthebuilding.Theinformationcontainedinthismanual

pertainstoallmodelsandgascontrolsystemsunless

otherwisenoted.

Appliance Certication

WARNING: This unit is not for use with solid fuels.

Thisreplaceisdesigncertiedinaccordancewith

AmericanNationalStandard/CSAStandardANSIZ21.88/

CSA2.33andbyUnderwritersLaboratoriesasaDirect

VentGasFireplaceHeaterandshallbeinstalledaccording

totheseinstructions.

Consultyourlocalbuildingcodeagency,priorto

installation,toensurecompliancewithlocalcodes-

includingpermitsandinspections.

Thereplace,wheninstalled,mustbeelectrically

groundedinaccordancewithlocalcodesor,inabsenceof

localcodes,withtheNational Electric Code ANSI/NFPA

70orCanadianElectriccode,CSAC22.1,ifanexternal

electricalsourceisutilized.

Thesemodelsmaybeinstalledinabedroomorbed-sitting

roomintheU.S.A.andCanada.

Qualied Installing Agency

Installationandreplacementofgaspiping,gasutilization

equipmentoraccessoriesandrepairandservicingof

equipmentshallbeperformedonlybyaqualiedagency.

Theterm“qualiedagency”meansanyindividual,

rm,corporationorcompanywhicheitherinpersonor

througharepresentativeisengagedinandisresponsible

for(a)theinstallationorreplacementofgaspipingor

(b)theconnection,installation,repairorservicingof

equipment,whoisexperiencedinsuchwork,familiarwith

allprecautionsrequiredandhascompliedwithallthe

requirementsoftheauthorityhavingjurisdiction.

Commonwealth of Massachusetts: Theinstallation

mustbemadebyalicensedplumberorgastterinthe

CommonwealthofMassachusetts.

WARNING:ANYCHANGETOTHISFIREPLACEOR

ITS CONTROLS CAN BE DANGEROUS.

Improperinstallationoruseofthereplacecancause

seriousinjuryordeathfromre,burns,explosions,or

carbonmonoxidepoisoning.

Theinstallationmustconformwithlocalcodesor,in

theabsenceoflocalcodes,withtheNational Fuel Gas

Code ANSI Z223.1/NFPA 54* Natural Gas and Propane

Installation Code, or CSA B149.1 in Canada. *Available from

the American National Standards Institute, Inc. 11 West 42nd St., New

York, N.Y. 10036.

Any alteration of the original design, installed other

than as shown in these instructions or use with

a type of gas not shown on the rating plate is the

responsibility of the person and company making the

change.

Important

AllcorrespondenceshouldrefertocompleteModel

Number,SerialNumberandtypeofgas.

High Altitude

Wheninstallingthisunitatanelevationabove2000feet

(intheUnitedStates)itmaybenecessarytodecrease

theinputratingbychangingtheexistingburneroricetoa

smallersize.Generally,inputshouldbereduced4percent

foreach1000feetabovesealevel.However,iftheheating

valueofthegashasbeenreduced,thisgeneralrulemay

notapply.Checkwithlocalgasutilityforproperoricesize

identication.

Canadian High Altitude

Altitude:0-4500feet(0-1370m)

Wheninstallingthisunitatanelevationabove4500feet

(inCanada),checkwithlocalauthorities.

Consultyourlocalgasutilityforassistanceindetermining

theproperoriceforlocation.

Preparation

Thisdirectventgasreplaceanditscomponentsare

testedandsafewheninstalledinaccordancewiththis

InstallationManual.Reporttoyourdealeranyparts

damagedinshipment,specicallycheckglasscondition.

Donotinstallunitwithdamaged,incomplete,orsubstitute

parts.Readallinstructionsbeforestartinginstallationand

followtheseinstructionscarefullyduringinstallationto

insuremaximumbenetandsafety.Failuretofollowthem

willvoidyourwarrantyandmaypresentarehazard.

Thewarrantywillbevoidedby,andthewarranter

disclaimsanyresponsibilityforthefollowingactions:

• Installationofanydamagedreplaceorventsystem

component.

• Modicationofthereplaceordirectventsystem.

• InstallationotherthanasinstructedbyEmpireComfort

Systems,Inc.

• Improperpositioningofthelogs,glassdooror

decorativerock.

• Installationand/oruseofanycomponentpartnot

manufacturedorapprovedbymanufacturer.

INTRODUCTION

31509-13-0416 Page 7

SPECIFICATIONS

DVCD32NAT DVCD32LP DVCD36NAT DVCD36LP DVCD42NAT DVCD42LP

InputBTU/HrMaximum 18,000 18,000 20,000 20,000 25,000 25,000

BTU/HrMinimum(millivoltonly) 14,000 14,000 14,000 16,500 18,000 19,500

KWH (Maximum) 5.3 5.9 7.3

(Minimum) 4.1 4.1 5.3

NAT.

Orice

#46 (.081”)

P254

- 2.10 mm P288 -

#42 (.0935”)

P286

-

AirShutterOpening

1/16”

(1.6mm)

- 1/16” (1.6mm) - 3/16”(4.8mm) -

LP

Orice -

#56 (.0465”)

P287

-

#55 (.052”)

P182

-

1.45 mm

P208

AirShutterOpening -

1/4”

(6.3mm)

-

5/16”

(7.9mm)

-

5/16”

(7.9mm)

Heightwithoutstandoff -

32 3/4”

(832mm)

-

32 3/4”

(832mm)

-

34 3/4”

(883mm)

Width -

34”

(864mm)

-

37”

(940mm)

-

43”

(1092mm)

Depth -

16 3/8”

(416mm)

-

16 3/8”

(416mm)

-

16 3/8”

(416mm)

GasInletShutoffValve(Pipe) - 1/2 NPT - 1/2 NPT - 1/2 NPT

NOTE: Airshuttersettings are factory minimum settings. Some venting congurations may require minor air shutter adjustments for

optimumperformance.

Remote Control Options

& Accessories

Description Models Used On

FRBC MillivoltBatteryRemoteON/OFF DVCD(32,36,42)FP(3,7)

FRBTC MillivoltBatteryRemoteThermostat DVCD(32,36,42)FP(3,7)

FREC DirectIgnition/Millivolt120VON/OFFRemote DVCD(32,36,42)FP(3,5)

TMW MillivoltWirelessWallThermostat DVCD(32,36,42)FP(3,7)

TRW MillivoltReedSwitchWallThermostat DVCD(32,36,42)FP(3,7)

FWS-1 DirectIgnition/MillivoltWallSwitch DVCD(32,36,42)FP(3,5,7)

Venting Options Description

DVVK-4TSP Topventkit(horizontal)-4½"to6"(114.3mmto152mm)wallthickness

DVVK-4TP Topventkit(horizontal)-8"to12"(203mmto305mm)wallthickness

DVVK-4RP Rearventkit(horizontal)-5"to7"(127mmto178mm)wallthickness

DVVK-4VP Verticalventkit

DVVK-4F Horizontalexventkit(4'FLEX)

DVVK-4RE Horizontalroundtermination(wallthicknessupto117/16")

DV822 VinylsidingkitforDVVK-4RE

FIREPLACE BARRIER SCREENS

SCREEN MODEL DESCRIPTION FIREPLACE MODELS USED ON

DVFB32SBL FireplaceBarrierScreen,MatteBlack DVCD32FP

DVFB36SBL FireplaceBarrierScreen,MatteBlack DVCD36FP

DVFB42TBL FireplaceBarrierScreen,MatteBlack DVCD42FP

Note:Arescreenisrequiredforoperationoftheappliance,butaresoldseparately.Followtheinstructionsthatcomewithyourrescreen

forproperinstallation.

31509-13-0416Page 8

Figure 1

Special Venting Components (Simpson Duravent)

SeeEmpireComfortSystemsRetailPriceListforSimpsonDuraventpartnumbersandpricing.

SpecialDVVentKits

AvailablefromEmpireComfortSystems,Inc.dealers

DVVK-4FV VerticalFlexVentKit4"x7"

DVVK-4VP

Direct-VentFireplaceVentKit-Vertical,IncludesSD-991,SD-953,and

SD-943

DVVK-4TP

Direct-VentFireplaceVentKitforTopVent,Thru-the-wall,8to11inchwall

thickness,IncludesSD-911,SD-985,SD-990andSD-942

DVVK-4RP

Direct-VentFireplaceVentKitforRearVent,5to7inchwallthickness,

(standardthru-the-wallventing)IncludesSD-908,SD-985andSD-942

DVVK-4RE

Direct-VentFireplaceVentKitforRearVent,Thru-thewall,5to7inchwall

thickness,(standardthru-the-wallventing)IncludesSD-908,SD985and

SD-942

DVVK-4TSP

Direct-VentFireplaceVentKitforTopVent,Thru-the-wall,5to7inchwall

thickness,IncludesSD-908,SD-985,SD-990andSD-942

VIB6A VerticalInletBafeKitfor65/8"diameter.

VIB7A VerticalInletBafeKitfor7"diameter.

VENT SYSTEM IDENTIFICATION

ThefollowingventsystemsareacceptableforusewiththeDVCD

(32,36,42)seriesreplaces:

SimpsonDuravent®GS4"-6⅝"

AmericanMetalProducts4"-6⅝"

SelkirkDirect-Temp®4"-6⅝"

SecuritySecureVent®4"-6⅝"

ExcelDV4”-6⅝”

MetalFabSureSeal®4”-6⅝”

BDMManufacturing4”-6⅝”

EmpireHorizontalRoundTerminationKits:

DVVK-4RE, DVVK-4REVS

EmpireFlexventKits:DVVK-4F,DVVK-4FREVS,DVVK-4FRE

SPECIAL VENT SYSTEMS

Begintheventsysteminstallationbyselectingthetypeofventing

tobeinstalledandthepaththatitwilltake.Verifythatclearances

aremetthroughoutthepathoftheventingsystem.Determineif

thereplaceistobeventedoutthetoporouttherear.

NOTICE:Somereplacescannotbeventedouttherearofthe

replace.

Determinehowtheventsystemwillbeterminatedoutthe

sideofthehouseorthroughtheroof.Verifyclearancesforthe

termination.

Whenselectingaventsystemforusewiththereplace,referto

the“SpecialVentSystems”sectioninthismanualtodetermine

whatsystemsareacceptable.Checkallclearancesandventing

components.Identifyifanyproblemsexistingintheventsystem.

Use Figure 22onpage18fortopventingorFigure 32onpage

22forrearventingtoeliminateissuesafterinstallation.Check

pipediameteronventsystemandreplacetoverifythesizeis

thesame.

NOTICE: All outer connection joints must be sealed with

aluminum tape, screws or silicone sealant rated above

300°F/149°C. The inner ue joints do not require any sealant.

31509-13-0416 Page 9

Figure 2

Dim DVCD32 DVCD36 DVCD42

A

34"

864 mm

37"

940 mm

43"

1092 mm

B

31"

787 mm

34"

864 mm

40"

1016 mm

C

231/16"

585 mm

231/16"

585 mm

251/16"

636 mm

D

355/8"

905 mm

355/8"

905 mm

375/8"

956 mm

E

323/4"

832 mm

323/4"

832 mm

343/4"

883 mm

F

163/8"

416 mm

163/8"

416 mm

16 3/8

416 mm

G

241/2"

622 mm

241/2"

622 mm

261/2"

673 mm

H

71/8"

181 mm

71/8"

181 mm

71/8"

181 mm

I

211/2"

546 mm

241/2"

622 mm

301/2"

774 mm

J

103/4"

273 mm

121/4"

311 mm

151/4"

387 mm

K

91/4"

235 mm

91/4"

235 mm

91/4"

235 mm

FIREPLACE DIMENSIONS

31509-13-0416Page 10

CLEARANCES

Clearance to Combustibles

Back 0"(0mm)

Side 0"(0mm)

Floor 0"(0mm)

TopStand-off 0"(0mm)

TopFramingEdge 3"(76mm)

Figure 3

Combustible Material

Nogreetingcards,stockingsorornamentationofanytypeshould

beplacedonorattachedtothereplace.Theowofheatcan

ignitecombustibles.

Note:WhenusingEmpireEMBF,UMC,andUMFSeries

FullMantelswithDVCD32andDVCD36SeriesFireplaces,

combustibleclearancemaybereducedto1”clearancefromtop

edgeofreplaceface.

Figure 4

Mantel Chart

Figure 5

Clearances

Clearancefromtopfrontedgeofreplacetoceilingis36”

Clearancefromsideofreplacetoadjacentsidewallis6”.

Figure 6

31509-13-0416 Page 11

Figure 7

Note:IslandandRoomDividerinstallationispossibleaslongasthehorizontalportionoftheventsystemdoesnotexceed20feetwith

aminimumverticalrunof8feet.SeedetailsinVentingSection.

WhenyouinstallyourDirectVentFireplaceinRoomdividerorFlatonwallcornerpositions,aminimumof6inchesclearancemustbe

maintainedfromtheperpendicularwallandthefrontedgeoftheappliance.

LOCATING FIREPLACE

31509-13-0416Page 12

GAS SUPPLY

Thegaspipelinecanbebroughtinthroughtherightorleftsideof

theappliance.ConsultthecurrentNationalFuelGasCode,ANSI

Z223.1CAN/CGA-B149(.1or.2)installationcode.

Recommended Gas Pipe Diameter

PipeLength

Schedule40Pipe

InsideDiameter

Tubing,TypeL

Outside Diameter

Nat. L.P. Nat. L.P.

0-10feet 1/2” 3/8” 1/2” 3/8”

10-40feet 1/2” 1/2” 5/8” 1/2”

40-100feet 1/2” 1/2” 3/4” 1/2”

100-150feet 3/4” 1/2” 7/8” 3/4”

Note:Neveruseplasticpipe.Checktoconrmwhetheryour

localcodesallowcoppertubingorgalvanized.

Note: Sincesomemunicipalitieshaveadditionallocalcodes,itis

alwaysbesttoconsultyourlocalauthorityandinstallationcode.

Theuseofthefollowinggasconnectorsisrecommended:

— ANSZ21.24ApplianceConnectorsofCorrugatedMetal

TubingandFittings.

— ANSZ21.45AssembledFlexibleApplianceConnectorsof

OtherThanAll-MetalConstruction

Theaboveconnectorsmaybeusedifacceptablebytheauthority

havingjurisdiction.ThestateofMassachusettsrequiresthata

exibleapplianceconnectorcannotexceedthreefeetinlength.

FLEXIBLE GAS LINE CONNECTION

GAS SUPPLY

TEE HANDLE

FLEX TUBING

FLARE FITTING FLARE SHUT

OFF VALVE

Figure 8

GasSupplyPressure(inchesw.c.)

Minimum Normal Maximum

Natural Gas 4.5" 7.0" 14.0"

LP(Propane) 10.8" 11.0" 14.0"

ManifoldPressure(inchesw.c.)

Normal (HI)

Natural Gas 3.5"

LP(Propane) 10.0"

Installing a New Main Gas Cock

Eachapplianceshouldhaveitsownmanualgascock.

Amanualmaingascockshouldbelocatedinthevicinityof

theunit.Wherenoneexists,orwhereitssizeorlocationisnot

adequate,contactyourlocalauthorizedinstallerforinstallationor

relocation.

Compoundsusedonthreadedjointsofgaspipingshallbe

resistanttotheactionofliqueedpetroleumgases.Thegas

linesmustbecheckedforleaksbytheinstaller.Thisshouldbe

donewithasoapsolutionwatchingforbubblesonallexposed

connections,andifunexposed,apressuretestshouldbemade.

Never use an exposed ame to check for leaks. Appliance

must be disconnected from piping at inlet of control valve

and pipe capped or plugged for pressure test. Never

pressure test with appliance connected; control valve will

sustain damage!

NOTE: Themillivoltgascontrolsareequippedwithacaptured

screwtypepressuretestpoint,thereforeitisnotnecessaryto

providea1/8”testpointupstreamofthecontrol.

Ondirectignitionvalves,hexplugsmaybereplacedwithhose

ttingsforpressurechecks,thenreinstalledbeforeoperating

replace.

Whenusingcopperorexconnectoruseonlyapprovedttings.

Theapplianceandit’sindividualshutoffvalvemustbe

disconnectedfromsupplypipingsystemduringanypressure

testingofthatsystemattestpressuresinexcessof1/2psig

(3.5kPa).

Theappliancemustbeisolatedfromthegassupplypiping

systembyclosingitsindividualmanualshutoffvalveduringany

pressuretestingofthegassupplypipingsystemattestpressures

equaltoorlessthan1/2psig(3.5kPa).

Attention! Ifoneoftheproceduresresultsinpressuresinexcess

of1/2psig(14”w.c.)(3.5kPa)onthereplacegasvalve,itwill

resultinahazardouscondition.

Checking Manifold Pressures

BothPropaneandNaturalgasvalveshaveabuilt-inpressure

regulatorinthegasvalve.Naturalgasmodelswillhavea

manifoldpressureofapproximately3.5”w.c.(.871kPa)atthe

valveoutletwiththeinletpressuretothevalvefromaminimum

of4.5”w.c.(1.120kPa)forthepurposeofinputadjustmentto

amaximumof14.0”w.c.(3.484kPa).Propanegasmodelswill

haveamanifoldpressureapproximately10.0”w.c.(2.49kPa)

atthevalveoutletwiththeinletpressuretothevalvefrom

aminimumof10.8”w.c.(2.68kPa)forthepurposeofinput

adjustmenttoamaximumof14.0”w.c.(3.484kPa).

GAS LINE HOLE

(BOTH SIDES)

2”

10”

FROM FRONT OF

APPLIANCE TO

GAS LINE HOLE

Figure 9

31509-13-0416 Page 13

INSTALLATION

Framing and Finishing

1. Chooseunitlocation.

2. Frameinreplacewithaheaderacrossthetop.Itis

importanttoallowfornishedfacewhensettingthedepthof

theframe.

3. Attachreplacetoframeusingadjustableframe.Preset

depthtosuitfacingmaterial(adjustableto1/2”,5/8”or3/4”

depths).

4. Useeight1/2”hex-headscrewssuppliedinhardware

package,toscrewthroughslottedholesindrywallstripand

thenscrewintopre-drilledholesonreplaceside.Measure

fromfaceofreplacetofaceofdrywallstriptodetermine

naldepth.

Figure 10

Installation of Hood

1. Retrievehoodfromopenareaabovereboxglass.

2. Placehoodinopenareaabovereboxglasssoopeningof

hoodisatthebottomoftheopenarea.

Note:Fireboxheatshieldwillrestontopofreboxinsideof

openarebetweentopueandhoodrunningthewidthofthe

rebox.

3. Securehoodwithscrewsonbothsideofhoods.

Note:Topofhoodshouldbeushwithfaceofreplace.

Vent Pipe Clearance

Note: Maintainoneinchofclearancearoundverticalventpipe.

See Figure 11.Forhorizontalvent,maintainaminimum1”

clearancetothebottomandsidesofthevent,and3”clearance

tocombustiblesabovetheventpipe.See Figure 12.

Figure 11

Figure 12

31509-13-0416Page 14

INSTALLATION (continued)

Flush Mount Mantel Installation

Thereplacemustextend3/4”beyondnishedwallsurface

whenusingaushmountmantel.RefertoFigure 13tolocate

nailingangesonreplacesides.Markanddrilltwo1/8”holes

intoreplacesidetomounteachnailingange.Useeight1/2”

hex-headscrewssuppliedinhardwarepackagetoattachnailing

angestoreplacesides.

Figure 13

Attention: Whenreplaceisinstalledinoptionalfullcabinet

mantelorcornermantelthefournailingangesshowninFigure

13willnotbeinstalledonthesideofoutercasing.Thereplace

willbeattachedtothefullcabinetmantelorcornermantelwith

thetwonailingangeslocatedonthetopoftheoutercasing

assembly.

Framing

Fireplaceframingcanbebuiltbeforeorafterthereplaceisset

inplace.Framingshouldbepositionedtoaccommodatewall

coveringandreplacefacingmaterial.Thereplaceframing

shouldbeconstructedof2x4lumberorheavier.Theframing

headersmayrestonthereplacestandoffs.RefertoFigure 14

forminimumframingdimensions.

CAUTION: MEASURE FIREPLACE DIMENSIONS AND VERIFY

FRAMING METHODS, AND WALL COVERING DETAILS

BEFORE FRAMING CONSTRUCTION BEGINS.

Framing dimension "A" includes a three inch clearance for

standoffs on rebox. After installing rebox into framing,

the nished wall surface must cover the three inch

opening above the rebox.

Note:Fornishingtotopofreplace,refertoFigure 15.

DVCD32 DVCD36 DVCD42

"A" 353/4"

(908 mm)

353/4"

(908 mm)

373/4"

(959 mm)

"B" 343/8"

(873 mm)

373/8"

(949 mm)

433/8"

(1102 mm)

"C" 163/8"

(416 mm)

163/8"

(416 mm)

163/8"

(416 mm)

Figure 14

Attention: Add3-3/4”to“A”dimensionswhenusingaush

mantelbase.

Attention: Ifabaseormantelisnotusedandtheapplianceis

installeddirectlyoncarpeting,tileorothercombustiblematerial

otherthanwoodooring,itshallbeinstalledonametalorwood

panelextendingthefullwidthanddepthoftheappliance.The

verticaldimensioninFigure 14mustbeadjustedwhenametal

orwoodpanelisplacedbeneaththeappliance.

Finishing

Finishthewallswiththematerialofyourchoice.Figure 5

onpage10showstheminimumverticalandcorresponding

maximumhorizontaldimensionsofmantelsorothercombustible

projectionsabovethetopfrontedgeofthereplace.

Onlynon-combustiblematerialsmaybeusedtocovertheblack

replacefront.

Warning: When nishing the replace never obstruct

or modify the air inlet/outlet louvers in any manner.

Provide adequate clearances around air openings into the

combustion chamber.

Caution: Ifthejointsbetweenthenishedwallandthereplace

surround(topandsides)aresealed,a300°Fminimumsealant

materialmustbeused.Thesejointsarenotrequiredtobe

sealed.Onlynon-combustiblematerial(using300°Fminimum

adhesiveifneeded),canbeappliedasfacingtothereplace

surround.

31509-13-0416 Page 15

INSTALLATION (continued)

Flush Wall Installation

Figure 15

Combustible Surround Installation

Figure 16

Attention:Coldclimateinstallationrecommendation:When

installingthisunitagainstanon-insulatedexteriorwall,itis

recommendedthattheouterwallsbeinsulatedtoconformto

applicableinsulationcodes.

Vent Runs

Inplanningtheinstallationforthereplace,itisnecessaryto

installcertaincomponentsbeforetheapplianceiscompletely

positionedandinstalled.Theseincludethedirectventsystem,

gaspipingfortheapplianceandtheelectricalwiring.(Ifthefan

optionisused.)

Theappliancecanbemountedonanyofthefollowingsurfaces:

1. Aat,hardcombustible(burnable)surface.

2. Araisedwoodenplatform.

3. Fourcornersupports.(Example:Fourconcretemasonry

blocks.)Thesesupportsmustbepositionedsotheycontact

allfourperimeteredgesonthebottomoftheunit.

VERTICAL, 90° ELBOW WITH HORIZONTAL TERMINATION

Figure 17

31509-13-0416Page 16

HORIZONTAL ONLY, STRAIGHT OUT THE BACK

Figure 18

VERTICAL, 90° ELBOW TO HORIZONTAL OUT THE WALL

Figure 19

"A" "B" Models

6"

51/8"to61/2"

(130 mm to 165 mm)

DVCD 32,36,42

9"

81/8"to91/2"

(206 mm to 241 mm)

DVCD 32,36,42

12"

111/8"to121/2"

(283 mm to 317 mm)

DVCD 32,36,42

"A" "B" "C"

6"

111/4"to123/4"

(286 mm to 324 mm)

43/4"to61/4"

(121 mm to 159 mm)

9"

141/4"to153/4"

(362 mm to 400 mm)

73/4"to91/4"

(197 mm to 235 mm)

12"

171/4"to183/4"

(438 mm to 476 mm)

103/4"to121/4"

(273 mm to 311 mm)

INSTALLATION (continued)

31509-13-0416 Page 17

CORNER INSTALLATION VERTICAL, 90° ELBOW TO HORIZONTAL OUT THE WALL

Figure 20

CORNER INSTALLATION HORIZONTAL, 45° ELBOW TO HORIZONTAL OUT THE WALL

Figure 21

DVCD32 DVCD36 DVCD42

"A" "B" "B" "B"

6"

(152 mm)

4"to51/2"

(102 mm to 140 mm)

4"to5"

(102 mm to 127 mm)

n/a

9"

(229 mm)

6"to71/2"

(152 mm to 191 mm)

6"to71/2"

(152 mm to 191 mm)

4"to51/2"

(102 mm to 140 mm)

12"

(305 mm)

9"to101/2"

(229 mm to 267 mm)

9"to101/2"

(229 mm to 267 mm)

9"to101/2"

(229 mm to 267 mm)

Dim. DVCD32 DVCD36 DVCD42

A

361/8"

918 mm

383/8"

975 mm

421/2"

1080 mm

B

251/2"

648 mm

271/8"

689 mm

301/8"

765 mm

C

111/2"

292 mm

125/8"

321 mm

143/4"

375 mm

D

511/8"

1299 mm

541/4"

1378 mm

601/8"

1527 mm

INSTALLATION (continued)

31509-13-0416Page 18

To Use the Vent Graph

1. Determinetheheightofthecenterofthehorizontalvent

pipe.UsingthisdimensionontheSidewallVentGraph,

locatethepointitintersectswiththeslantedgraphline.

2. Fromthepointofthisintersection,drawaverticallineto

thebottomofthegraph.

3. Selecttheindicateddimension,andpositiontheunitin

accordancewithsame.

EXAMPLE A:

Iftheverticaldimensionfromtheooroftheunitis35feet,the

horizontalruntotheouterwallangemustnotexceed6.5feet.

EXAMPLE B:

Iftheverticaldimensionfromtheooroftheunitis6.5feet,the

horizontalruntotheouterwallangemustnotexceed14.5

feet.

SPECIAL NOTE: Foreach45degreeelbowinstalledinthe

horizontalrun,thelengthofthehorizontalrunMUSTbe

reducedby18"(457mm).Thisdoesnotapplyifthe45degree

elbowsareinstalledontheverticalpartoftheventsystem.

Reduce3'forevery90°elbow.

Example:Accordingtothechartthemaximumhorizontalvent

lengthis20'andiftwo45degreeelbowsarerequiredinthe

horizontalventitmustbereducedto17'.

Themaximumnumberof45degreeelbowspermittedperside

wallinstallationistwo.Theseelbowscanbeinstalledineither

theverticalorhorizontalrun.

Note:Onverticalventingtherstelbowdoesnotgetcounted.

 Acceptableverticalandhorizontalventrun.

 (40'maximumverticaland20'maximumhorizontal)

 Unacceptableverticalandhorizontalventrun.

Figure 22

Venting Graph (Dimensions in Feet)

VENTING FIREPLACE - TOP

31509-13-0416 Page 19

VENTING FIREPLACE - TOP (continued)

Below Grade Installation

Whenitisnotpossibletomeettherequiredventterminal

clearancesof12”(305mm)abovegradelevel,asnorkelkitis

recommended.Itallowsinstallationdepthdownto7”(178mm)

belowgradelevel.The7”(178mm)ismeasuredfromthecenter

ofthehorizontalventpipeasitpenetratesthroughthewall.

Ensure the sidewall venting clearances are observed. If

venting system is installed below ground, we recommend

a window well with adequate and proper drainage to be

installed around the termination area.

TYPICAL BASEMENT INSTALLATION

Figure 23

Examplesofpossibleventingsystemsusingone90°elbow.

Eightfeetislistedasminimumverticalventrunwith20feetof

maximumhorizontalventrun.Verticaldimensionsarebasedon

centerlinetocenterlineofpipe.Horizontaldimensionsarebased

oncenterlineofpipetoendoftermination.

Figure 24

Examplesofpossibleventingsystemsusingtwo90°elbows.

VislistedasminimumverticaldimensionsandH1+H2islisted

astotalofmaximumhorizontaldimensions.Themaximum

verticalandhorizontaldistancesfortwo90°elbowsasshownin

Figure 25 is20feet(6.1m).

Attention:RefertoFigure 22foradditionalventingrequirements.

Figure 25

31509-13-0416Page 20

VENTING FIREPLACE - TOP (continued)

Figure 27

Figure 28

FIREPLACE

SERIES

HARD ELBOW DIMENSIONS

"A" "B" "C" "D"

DVCD32FP

41-1/2"

(1054 mm)

4"

(102 mm)

6"

(152 mm)

91/8"

(232 mm)

DVCD36FP

41-1/2"

(1054 mm)

4"

(102 mm)

6"

(152 mm)

91/8"

(232 mm)

DVCD42FP

43-1/2"

(1105 mm)

4-1/2”

(114 mm)

6-1/2”

(165 mm)

91/8"

(232 mm)

FIREPLACE

SERIES

FLEX PIPE 90 DEGREE BEND

"A" "B" "C" "D"

DVCD32FP

43"

(1092 mm)

4-1/2"

(114 mm)

6-1/2"

(165 mm)

91/8"

(232 mm)

DVCD36FP

43"

(1092 mm)

4-1/2"

(114 mm)

6-1/2"

(165 mm)

91/8"

(232 mm)

DVCD42FP

45"

(1143 mm)

4-1/2"

(114 mm)

6-1/2"

(165 mm)

91/8"

(232 mm)

Figure 26

MINIMUM HOLE LOCATION DIMENSIONS FOR THROUGH

THE WALL HORIZONTAL INSTALLATIONS WITH 90 DEGREE

ELBOW OFF TOP OF FIREPLACE

SEE FIGURE 22 ON PAGE 18 FOR PERMISSIBLE "H" AND

"V" DIMENSIONS.

Positioning the Fireplace

Determinetheexactpositionoftheappliancesothedirect

ventterminationwillbecentered(ifpossible)betweentwo(2)

studs.Thiswillavoidanyextraframing.Allventkitpipesshould

beassembledontheunitaftertheunitismovedintothenal

position.

Cutting the Hole

Afterthereplacehasbeenpositionedinitspermanentlocation,

theholethroughtheexteriorwallofthehousecanbecut.

Thisholemustbe10"(254mm)highx10"(254mm)widewith

itscenterlinedeterminedbytheamountofverticalriseand

horizontalrunofthetermination.See Figure 26. Whenlocating

theholeitmustbenotedthatthebottomofthecapmustbe12"

(305mm)abovethegroundlevel,andtopofthecapmustbe

nolessthan18"(457mm)belowacombustibleprojection,and

nocloserthan9"(229mm)toanywallrunningparalleltovent

termination.See Figure 27.

Page is loading ...

Empire INTERMITTENT PILOT DVCD36FP71P-1 Installation Instructions And Owner's Manual

Empire INTERMITTENT PILOT DVCD36FP71P-1 Installation Instructions And Owner's Manual

Related papers

Other documents