Haier ES100V-R1 User manual

Category
Water heaters & boilers
Type
User manual
1 2
ES50V-G1(H)
ES70V-G1(H)
ES100V-G1(H)
Proprietary No.
**********
V
Please read this Instruction Manual carefully before use.
Please retain this manual for future reference.
Safety Notices
(Please read before use)
Electrical Diagram
·
Exterior and accessories
·
Technical parameters
Electrical Diagram
Technical parameters
Troubleshooting
Symptom Things to Check Solutions
No water
1
Whether the water supply has
stopped or whether the water
pressure is too low
Check
2
Whether the water-usage
point is blocked or whether
the hot water valve is opened
Check and clean
Only cold water but
the heating indica-
tor lamp is lit
1
Whether hot water outlet is
not opened
Check and open
2
Whether the water tempera-
ture is adjusted
Increase the temperature to the
required value. Once the water is
heated to the pre-set temperature,
control ow volume of cold and
hot water using the moderating
mixing valve.
3
Heating time is too short
and set temperature is not
achieved
Continue heating
4
Whetehr heating pipe is
damaged
Con rm this is not due to the rea-
sons
①②③
, then contact Mainte-
nance Department
Only cold water and
the heating indica-
tor lamp is not lit
1
Whether power is properly
connected
Check power socket
2
Whether thermostat is out of
control
Con rm that this is not due to rea-
son
, then contact Maintenance
Department
Heating indicator
light is on all the
time
1
Water has not reached the set
temperature
Continue heating
2
Whether thermostat is out of
control
Con rm it is not due to reason
,
then contact Maintenance Depart-
ment
Water volume is
sometimes large or
small, or water is
sometimes hot or
cold
Whether water pressure
is stable
Set lower mixing valve or ensure
water pressure is stable before
use
Small hot water
out ow volume
1
Whether the present tempera-
ture setting is too low
Calibrate using the method stipu-
lated in the Instruction Manual
2
Whether water pressure is too
much
Set lower mixing valve
Prohibited
Compulsory
Matters
Essential
Matters
Immediately cut off power supply and
contact our Service Center once the
water heater does not work properly
or emits burnt smell.
220V
/
50Hz independent power source
must be used at all times.
To ensure safety, the water heater
should be connected to independent
sockets (do not use adapters), with re-
liable earthing. In addition, the power
socket must conform to national stan-
dards. Use of water heater without
reliable earthing is strictly prohibited.
Use pen multimeter to check whether
the live line and zero line are reverse.
Do not use damaged wire and power
socket. Promptly clean the dust on the
power plug and socket.
Check the power meter and the elec-
tric wire's diameter to ensure that they
comply with the rated current for the
water heater. Where necessary en-
gage quali ed electrician to check the
electric circuit.
Do not touch the plug with wet hands,
and make sure that the water heater,
plug socket do not come into contact
with water. If they are accidentally wet,
they must be checked by professions
appointed by our company before us-
ing, in order to prevent electrocution.
Storing of inflammable and explosive
items near the water heater is strictly
prohibited.
Do not connect to power when install-
ing or repairing the water heater.
Non-professionals are strictly prohib-
ited from carrying out repairs, main-
tenance, dismantling or revamping of
the water heater.
Installation of water heater outdoors is
strictly prohibited.
Do not install the water heater in an
environment which is susceptible to
ice-formation. Ice will cause the con-
tainer and water pipe to break, lead-
ing to scalding and water leakage.
Please take precautionary measures
during cold weather, in order to pre-
vent damage to water heater from
freezing.
If the soft power cable is damaged,
it must be replaced by professional
staff from the manufacturers or Main-
tenance Department in order to avoid
danger.
Take care not to be scalded by heated
water.
·
Touching of hot water valve and
pipes is strictly prohibited.
·
Make sure to check the water tem-
perature before use
; use only when
it feels suitable.
Do not use water from the water heat-
er for drinking or similar purposes.
Please cut off the power supply if the
water heater was not used for an ex-
tended period of time. Drain the water
heater of all water according to the in-
structions in the chapter on Cleaning
and Maintenance.
Forbidden
Warning
Caution
Caution
to high respectively.
weiv noitces-ssorCweiv raeRweiv tnorF Side view
A : Hot water outlet B : Cold water inlet C : Inner chamber
D : Temperature measurement pipe E : Heating pipe
F : Magnesium rod G : Wall hook
Model No.
Capacity
(L)
Net
weight
(kg)
a1
(mm)
b1
(mm)
c1
(mm)
d1
(mm)
e1
(mm)
f1
(mm)
Note:
1.
The margin of error for the above parameters (measurements, weight) is ±10%.
2. The thermometer is not a precision instrument. It consists of three areas denoted by blue;
orange and red, which indicate the temperature of water in the inner chamber from low
E
BTMT
L
N
EH
E
HL
L : Live wire (brown)
N : Zero line (blue)
MT : Manual-reset thermostat
BT : Adjustable thermostat
HL : Heating indicator light
EH : Heating pipe
E : Earth line (yellow-green;
dual color)
Home Water Heater
Instruction manual
Meanings of Icons
Earthing
Warning
Warning
Warning
Warning
Warning
Caution
Forbidden
Forbidden
Forbidden
Forbidden
Forbidden
Forbidden
Forbidden
CSH10D0037_en.indd 1
0040503115A
V98497
Exterior and accessories
ES50V-G1(H)
Unit
Ltem
ES70V-G1(H) ES100V-G1(H)
Water pressure
2000
0.80
0.80
0.80
2000 2000
ES50V-G1(H)
ES70V-G1(H)
ES100V-G1(H)
50
70
100
21
26
33
410
410
420
420
410
420
765
970
1285
100
200
220
100
200
480
100
200
730
5 6
3 4
Cleaning
External cleaning
Power must be switched off before cleaning the water heater.
Take a wet cloth and dab it with small quantity of neutral detergent. Lightly wipe the water heat-
er. Do not use petrol or other solvents. Finally use a dry cloth to wipe; make use to dry the water
heater thoroughly. Make sure not to use detergents containing abrasive agents (e.g. toothpaste);
acidic substances; chemical solvents (e.g. alcohol) or polish to clean the water heater.
Internal cleaning
In order to ensure that the water heater will work with high ef ciency, clean the heating tube
and inner chamber once every three years. Take care not to damage the exterior of the heat-
ing pipe and the protective layer on the surface of the inner chamber. Depending on the local
water quality and usage habit, the magnesium rod should be regularly replaced. If mainte-
nance is required, please contact the local Maintenance Department.
Check
When the water heater is in use, the safety valve should be checked once every month. To
check it, turn the safety valve's small
handle on the side of the water intake (take care not
to hurt your hand). If there is water owing out, the safety valve is working normally. Please
contact the local After-sales Department if no water ows out. In the event of damage to the
safety valve, please replace it with a safety valve of similar speci cations.
Regularly engage service personnel to carry out safety inspection and promptly clear the wa-
ter heating pipes of the scale. Check also the consumption of the magnesium rod; change it if
consumption becomes excessive.
Not in use for an extended period of time
If the water heater is not used for an extended period of time, please carry out the following steps:
1 Turn off the water pipe valve.
2 Screw the water drainage pipe to the safety valve's pressure-relief hole; turn on the safety
valve handle.
3
Turn the hot water valve to the maximum (at the same time unscrew the soft sprinkler pipe from
the water outlet valve; take care not be scalded by hot water), drain the inner chamber of water.
When the water heater needs to be used again, our recommendation is to open hot water valve
before switching on the power in order to prevent accidents. Allow any gas that may be trapped in
the pipe to be discharged. Do not smoke or allow other exposed re to be near the opened valve.
At the same time, make sure to carefully examine all the parts of the water heater and ensure
that they are in a perfect condition. Make sure to ll the inner chamber with water before use.
2
Observe
thermometer
the current
water temperature.
Operation Cleaning and Maintenance
Installation Precautions
Installation Precautions
Installation method
Installation instruction
ecnanetniaM dna gninaelClaunam noitcurtsnI
·
Packing List
drainage pipe)
Installing safety valve
Install the safety valve which has a rated pressure of 0.80MPa (its
connection is G1/2) into the water intake pipe with the arrow on the
safety valve pointing at the water heater. When the water heater is
heated by electricity, a small amount of water will ow from the safety
valve's pressure relief hole due to the expansion of water in the heat-
er. This is normal. The pressure-relief hole should be connected to the
atmosphere and free from blockage at all times.
Installation method for safety valve's drainage pipe: Attach an end of
the water drainage pipe onto the pressure relief hole on the safety
valve. You may cut the water drainage pipe to make it shorter, or ex-
tend it depending on the situation. Connect to the other end of the
water drainage pipe to the lower water outlet. This will prevent the
water from the pressure relief hole from splashing. The water drainage
pipe connected to the safety valve should be installed in
a slanted manner and in an environment
which is not prone to frost.
Pressure-relief hole
(connected to water
Safety valve
Mini handle
When installing the water heater, certain space should be reserved (not less than 250mm from
the top and bottom, and not less than 700mm from the front and the sides) for ease of subsequent
maintenance and repair. If the water heater was to be built into clip boards, the bottom section of
the clip board should be movable for ease of removal of plastic cover during maintenance.
Make sure the pressure on the water intake is not less than 0.05MPa, and not more than 0.75MPa.
The water heater should be installed indoors in a place where the ambient temperature is
above 0
º
C. The pipes should be closely laid out. The hot water outlet should be too far away
from the point of usage. If the distance exceeds 8 meters, the hot water pipe should have in-
sulation protection, in order to prevent heat loss.
The wall on which the water heater should be strong such as it is able to withstand four times
the weight of the water heater when filled with water. If the wall was not weight-bearing wall or
made of hollow bricks, adequate protective measures such as addition of support and
high-strength wall screw with back panel should be adopted.
The water heater should be installed in places such as it is easy to use and maintain and with
oor drain. In order that it will not cause damage to nearby facilities or those in the lower levels
during a leakage of the water tank or water pipe. It should not be installed over toilet bowls,
bathtub, wash basin or door frame in order that users do not feel oppressed or insecure.
Power socket for the water heater should be installed in dry places which do not easily come
into contact with water, in order not to affect the heater’s normal operation (it would be best
equipped with protective cover).
Do not reverse the installation for the water intake and outlet. The safety valve should be in-
stalled in the designated position and not moved without permission. The safety valve's pres-
sure-relief hole should be connected to the atmosphere and free from blockage at all times.
Use pen multimeter to check whether the live line and zero line are reverse. Turn on power
supply only when you have ensured that the heater is lled with water and that there is no wa-
ter leakage. The power supply should also conform with requirements.
Safety reminder: In order to prevent accidents, please use our compan
y's accessories during
installation. Do not replace them on your own or use substitutes. Please make sure to contact
our Maintenance Department if the accessories are damaged and replace them with the
accessories supplied by our company. Our company shall not be liable for any direct or
indirect losses caused as a result of accidents for failure to comply with the aforesaid.
All water pipes should be installed by qualified water pipe installation workers. The pipelines
should comply with the national standards and regulations on the prohibition of prevention tools to
draw water to water source pipelines by way of inverse siphon, as well as local building codes.
Must be installed by personnel in our company's After-sales Department or designated
installation personnel.
The water heater is wall-mounted type.
Determine the installation location of the water heater and drill 4 holes of 12mm and 65mm
deep in the wall with a churn drill. Insert the expansion hooks and expansion bolts into
corresponding holes and fasten them. Then, lift the water heater to put the hangers on the
hooks and bolts. Mount the flat shims, connecting wires on the back of the water heater and
nuts on the bolts in turn (as shown in Fig. 1) and fasten the nut. Then, check if they are firm.
Refer to “Install relief valve" to install the relief valve and other accessories (only for installation
reference). Remember to use Teflon tape to avoid leakage.
For ease of installation and removal of water heater, we would recommend that G1/2 loose
joints be installed at appropriate locations on the water inlet and outlet pipes of the water
heater. Determine the position of the hot water supply. Connect the water intake and outlet
pipe together with the water pipe to the positions reserved for use of hot water. Hot water pipe
should preferably not be too long in order to prevent heat loss.
Note: Make sure that the water heater is securely attached to the hook before letting it go;
otherwise it may drop and cause injury or property damage.
After completion of installation, make sure to turn on the water intake valve and mix-
ing valve since there is no water in the inner chamber. Turn the mixing valve to the
maximum for hot water outlet. Turn off the out- ow valve when water ows out from the
sprinkler or the water outlet (indicating that the container is lled with water). Turn off the
water outlet valve. Inspect all connections to ensure that there is not water leakage be-
fore connecting to power.
1
Adjust the water temperature
knob at the bottom of the water
heater to set the temperature.
The maximum temperature setting is 75
º
C
Temperature adjustment knob: Turn the
knob gradually clockwise to raise the
temeprature setting. The knob will not
continue to turn once it reaches maximum
temperature setting. Turn it anti-clockwise
graudally to reduce the temperature set-
ting.
If the heating indicator light is lit, it means that the water heater is heating
.
If the heating indicator is power off, it means that heating is finished and it will enter
heating insulation state or get closed totally.
.
Thermometer
Heating indicator light
Warning!
The water heater must be repaired or maintained by qualifi ed professionals. Improper
methods may cause serious injury or damage to property.
Packing list
Product Model No.
Electric
water heater
(unit)
Safety valve
drainage pipe
(set)
Expand-
able screw
(pcs)
Expand-
able Hook
(pcs)
Instruction
Manual
(copy)
ES50V-G1(H)
1 1 2 2 1ES70V-G1(H)
ES100V-G1(H)
Quantity
Name of parts
Expandable hook
Wall hook
Power will be automatically cut off when the water temperature reaches the set tem-
perature. Once it lowers to certain temperature power will be automatically connected.
When the water pressure is
0.80MPa and the pressure-relief hole on the safety valve
emits large volume of water, it means that the water pressure is excessive.
In such case, please notify the After-sales Department.
Things to note during use
1 Do not connect the power before lling the inner chamber with water in order to prevent
damage to the water heater.
2 Adjust the water temperature to the suitable level before use in order to prevent
scalding.
3 As long as the hot water is adequate, set a lower temperature to reduce heat loss, high
temperature corrosion and scaling, thus extending the water heater’s lifespan.
4 Do not place in ammable substances such as petrol near the water heater; otherwise it
5
To avoid danger caused by accidental resetting of the heating breaker, the power for the heat
cannot be supplied by timer and other external switch devices or connected to circuit with
frequent switching for facility use.
may cause re.
CSH10D0037_en.indd 2
2010-4-28 9:18:40
Safety valve
Cold water inlet
Nozzle
Hot water
outlet
Cold water
pipe
Direction of cold water
Direction of hot water
Hot water
pipe
OFF
MAX
Fig.1
  • Page 1 1
  • Page 2 2

Haier ES100V-R1 User manual

Category
Water heaters & boilers
Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI