Vega WEIGHTRAC 31 Operating instructions

Operating Instructions

Radiometric sensor for mass ow

detection

WEIGHTRAC 31

Four-wire 4 … 20 mA/HART

Document ID: 42374

2

Contents

WEIGHTRAC 31 • Four-wire 4 … 20 mA/HART

42374-EN-210311

Contents

1 About this document ............................................................................................................... 4

1.1 Function ........................................................................................................................... 4

1.2 Target group ..................................................................................................................... 4

1.3 Symbols used................................................................................................................... 4

2 For your safety ......................................................................................................................... 5

2.1 Authorised personnel ....................................................................................................... 5

2.2 Appropriate use ................................................................................................................ 5

2.3 Warning about incorrect use ............................................................................................. 5

2.4 General safety instructions ............................................................................................... 5

2.5 EU conformity ................................................................................................................... 6

2.6 NAMUR recommendations .............................................................................................. 6

2.7 Installation and operation in the USA and Canada ........................................................... 6

2.8 Environmental instructions ............................................................................................... 6

3 Product description ................................................................................................................. 7

3.1 Conguration .................................................................................................................... 7

3.2 Principle of operation........................................................................................................ 9

3.3 Packaging, transport and storage ..................................................................................... 9

3.4 Accessories.................................................................................................................... 10

3.5 Corresponding source container .................................................................................... 11

4 Mounting ................................................................................................................................. 13

4.1 General instructions ....................................................................................................... 13

4.2 Mounting instructions ..................................................................................................... 14

5 Connecting to power supply ................................................................................................. 24

5.1 Preparing the connection ............................................................................................... 24

5.2 Connection-Massowdetermination ........................................................................... 27

5.3 Connection - Summation ................................................................................................ 29

5.4 Connection - Tachometer ............................................................................................... 31

6 Adjustment with the display and adjustment module ........................................................ 34

6.1 Insert display and adjustment module ............................................................................ 34

6.2 Adjustment system ......................................................................................................... 35

6.3 Display and adjustment module - Indication of system parameters ................................ 36

6.4 Saving the parameterisation data ................................................................................... 41

7 Setup with PACTware ............................................................................................................. 42

7.1 Connect the PC .............................................................................................................. 42

7.2 Parameter adjustment with PACTware ............................................................................ 43

7.3 Parameteradjustment-Massowdetection .................................................................. 43

7.4 Saving the parameterisation data ................................................................................... 59

7.5 Real value correction ...................................................................................................... 59

8 Diagnostics and servicing .................................................................................................... 61

8.1 Maintenance .................................................................................................................. 61

8.2 Status messages ............................................................................................................ 61

8.3 Rectify faults ................................................................................................................... 64

8.4 Exchanging the electronics module ................................................................................ 65

8.5 Software update ............................................................................................................. 66

8.6 How to proceed if a repair is necessary .......................................................................... 66

3

Contents

WEIGHTRAC 31 • Four-wire 4 … 20 mA/HART

42374-EN-210311

9 Dismount................................................................................................................................. 68

9.1 Dismounting steps.......................................................................................................... 68

9.2 Disposal ......................................................................................................................... 68

10 Supplement ............................................................................................................................ 69

10.1 Technical data ................................................................................................................ 69

10.2 Dimensions .................................................................................................................... 74

10.3 Industrial property rights ................................................................................................. 79

10.4 Trademark ...................................................................................................................... 79

Safety instructions for Ex areas

TakenoteoftheExspecicsafetyinstructionsforExapplications.

These instructions are attached as documents to each instrument

with Ex approval and are part of the operating instructions.

Editing status: 2021-03-04

4

1 About this document

WEIGHTRAC 31 • Four-wire 4 … 20 mA/HART

42374-EN-210311

1 About this document

1.1 Function

This instruction provides all the information you need for mounting,

connection and setup as well as important instructions for mainte-

nance,faultrectication,theexchangeofpartsandthesafetyofthe

user. Please read this information before putting the instrument into

operation and keep this manual accessible in the immediate vicinity

of the device.

1.2 Target group

This operating instructions manual is directed to trained personnel.

Thecontentsofthismanualmustbemadeavailabletothequalied

personnel and implemented.

1.3 Symbols used

Document ID

This symbol on the front page of this instruction refers to the Docu-

ment ID. By entering the Document ID on www.vega.com you will

reach the document download.

Information, note, tip: This symbol indicates helpful additional infor-

mation and tips for successful work.

Note: This symbol indicates notes to prevent failures, malfunctions,

damage to devices or plants.

Caution: Non-observance of the information marked with this symbol

may result in personal injury.

Warning: Non-observance of the information marked with this symbol

may result in serious or fatal personal injury.

Danger: Non-observance of the information marked with this symbol

results in serious or fatal personal injury.

Ex applications

This symbol indicates special instructions for Ex applications.

•

List

The dot set in front indicates a list with no implied sequence.

1 Sequence of actions

Numbers set in front indicate successive steps in a procedure.

Battery disposal

This symbol indicates special information about the disposal of bat-

teries and accumulators.

5

2 For your safety

WEIGHTRAC 31 • Four-wire 4 … 20 mA/HART

42374-EN-210311

2 For your safety

2.1 Authorised personnel

All operations described in this documentation must be carried out

onlybytrained,qualiedpersonnelauthorisedbytheplantoperator.

During work on and with the device, the required personal protective

equipment must always be worn.

2.2 Appropriate use

WEIGHTRAC31isasensorforcontinuousmassowdetectionon

conveyor belts as well as screw or chain conveyors.

Youcannddetailedinformationabouttheareaofapplicationin

chapter "Product description".

Operational reliability is ensured only if the instrument is properly

usedaccordingtothespecicationsintheoperatinginstructions

manual as well as possible supplementary instructions.

2.3 Warning about incorrect use

Inappropriate or incorrect use of this product can give rise to applica-

tion-specichazards,e.g.vesseloverllthroughincorrectmounting

or adjustment. Damage to property and persons or environmental

contamination can result. Also, the protective characteristics of the

instrument can be impaired.

2.4 General safety instructions

This is a state-of-the-art instrument complying with all prevailing

regulations and directives. The instrument must only be operated in a

technicallyawlessandreliablecondition.Theoperatorisresponsi-

ble for the trouble-free operation of the instrument. When measuring

aggressive or corrosive media that can cause a dangerous situation

if the instrument malfunctions, the operator has to implement suitable

measures to make sure the instrument is functioning properly.

The safety instructions in this operating instructions manual, the na-

tional installation standards as well as the valid safety regulations and

accident prevention rules must be observed by the user.

For safety and warranty reasons, any invasive work on the device

beyond that described in the operating instructions manual may be

carried out only by personnel authorised by the manufacturer. Arbi-

traryconversionsormodicationsareexplicitlyforbidden.Forsafety

reasons,onlytheaccessoryspeciedbythemanufacturermustbe

used.

To avoid any danger, the safety approval markings and safety tips on

the device must also be observed.

This measuring system uses gamma rays. Therefore take note of the

instructions for radiation protection in chapter "Product description".

Any work on the source container may only be carried out under the

supervisionofaqualiedradiationprotectionocer.

6

2 For your safety

WEIGHTRAC 31 • Four-wire 4 … 20 mA/HART

42374-EN-210311

2.5 EU conformity

ThedevicefullsthelegalrequirementsoftheapplicableEUdirec-

tives.ByaxingtheCEmarking,weconrmtheconformityofthe

instrument with these directives.

The EU conformity declaration can be found on our homepage.

Electromagnetic compatibility

Instruments in four-wire or Ex-d-ia version are designed for use in an

industrial environment. Nevertheless, electromagnetic interference

from electrical conductors and radiated emissions must be taken into

account, as is usual with class A instruments according to EN 61326-

1.Iftheinstrumentisusedinadierentenvironment,theelectromag-

netic compatibility to other instruments must be ensured by suitable

measures.

2.6 NAMUR recommendations

NAMUR is the automation technology user association in the process

industry in Germany. The published NAMUR recommendations are

acceptedasthestandardineldinstrumentation.

ThedevicefullstherequirementsofthefollowingNAMURrecom-

mendations:

•

NE 21 – Electromagnetic compatibility of equipment

•

NE 43 – Signal level for fault information from measuring transduc-

ers

•

NE53–Compatibilityofelddevicesanddisplay/adjustment

components

•

NE107–Self-monitoringanddiagnosisofelddevices

For further information see www.namur.de.

2.7 Installation and operation in the USA and

Canada

This information is only valid for USA and Canada. Hence the follow-

ing text is only available in the English language.

Installations in the US shall comply with the relevant requirements of

the National Electrical Code (ANSI/NFPA 70).

Installations in Canada shall comply with the relevant requirements of

the Canadian Electrical Code.

2.8 Environmental instructions

Protection of the environment is one of our most important duties.

That is why we have introduced an environment management system

with the goal of continuously improving company environmental pro-

tection.Theenvironmentmanagementsystemiscertiedaccording

to DIN EN ISO 14001.

Pleasehelpusfullthisobligationbyobservingtheenvironmental

instructions in this manual:

•

Chapter " Packaging, transport and storage"

•

Chapter " Disposal"

7

3 Product description

WEIGHTRAC 31 • Four-wire 4 … 20 mA/HART

42374-EN-210311

3 Product description

3.1 Conguration

Thetypelabelcontainsthemostimportantdataforidenticationand

use of the instrument:

9

10

4

5

3

6

7

8

9

2

1

Fig. 1: Layout of the type label (example)

1 Instrument type

2 Product code

3 Electronics

4 Protection rating

5 Ambient temperature

6 Measurement width

7 Hardware and software version

8 Order number

9 Serial number of the instrument

10 ID numbers, instrument documentation

The type label contains the serial number of the instrument. With it

youcanndthefollowinginstrumentdataonourhomepage:

•

Product code (HTML)

•

Delivery date (HTML)

•

Order-specicinstrumentfeatures(HTML)

•

Operating instructions and quick setup guide at the time of ship-

ment (PDF)

•

Order-specicsensordataforanelectronicsexchange(XML)

•

Testcerticate(PDF)-optional

Move to " www.vega.com"andenterinthesearcheldtheserial

number of your instrument.

Alternatively, you can access the data via your smartphone:

•

Download the VEGA Tools app from the " Apple App Store" or the

" Google Play Store"

•

Scan the DataMatrix code on the type label of the instrument or

•

Enter the serial number manually in the app

This operating instructions manual applies to the following instrument

versions:

•

Hardware from 1.0.6

Type label

Serial number - Instru-

ment search

Scope of this operating

instructions

8

3 Product description

WEIGHTRAC 31 • Four-wire 4 … 20 mA/HART

42374-EN-210311

•

Software from 2.1.0

1)

•

Hardware from 2.0.0

•

Software from 3.0.0

Theinstrumentisavailableindierentelectronicsversions.Eachver-

sioncanbeidentiedviatheproductcodeonthetypelabel:

•

StandardelectronicstypePROTRACH.-XX

The scope of delivery encompasses:

•

Radiometric sensor

•

Measuring frame (optional)

•

Mounting accessories

•

Documentation

•

Bluetooth module (optional)

– This operating instructions manual

– Ex-specic"Safety instructions" (with Ex versions)

– Ifnecessary,furthercerticates

1

3

5

4

3

2

Fig. 2: WEIGHTRAC 31

1 Source container (e.g. SHLD-1)

2 WEIGHTRAC 31

3 Support stand

4 Crossbeam

5 Clamp collars

Note:

The appropriate source container (e.g. SHLD-1) must be ordered

separately.

Electronics versions

Scope of delivery

1)

It is not possible to update the software to 3.0.0. In this case the electronics

module must be exchanged.

9

3 Product description

WEIGHTRAC 31 • Four-wire 4 … 20 mA/HART

42374-EN-210311

3.2 Principle of operation

The instrument is suitable for bulk solid applications on conveyor belts

and screw conveyors. There are application possibilities in nearly all

areas of industry.

In radiometric measurement, a Caesium-137 or Cobalt-60 isotope

emits focussed gamma rays that are attenuated when penetrating

the conveyor belt and the medium. The PVT detector on the lower

side of the conveyor belt receives the radiation, whose strength is

proportional to the density. The measuring principle has proven to be

very reliable in conjunction with extreme process conditions because

it measures contactlessly from outside through the conveyor belt. The

measuring system ensures maximum safety, reliability and plant avail-

ability, independently of the medium and its properties.

3.3 Packaging, transport and storage

Your instrument was protected by packaging during transport. Its

capacity to handle normal loads during transport is assured by a test

based on ISO 4180.

The packaging consists of environment-friendly, recyclable card-

board. For special versions, PE foam or PE foil is also used. Dispose

of the packaging material via specialised recycling companies.

Transport must be carried out in due consideration of the notes on the

transport packaging. Nonobservance of these instructions can cause

damage to the device.

The delivery must be checked for completeness and possible transit

damage immediately at receipt. Ascertained transit damage or con-

cealed defects must be appropriately dealt with.

Up to the time of installation, the packages must be left closed and

stored according to the orientation and storage markings on the

outside.

Unless otherwise indicated, the packages must be stored only under

the following conditions:

•

Not in the open

•

Dry and dust free

•

Not exposed to corrosive media

•

Protected against solar radiation

•

Avoiding mechanical shock and vibration

•

Storage and transport temperature see chapter " Supplement -

Technical data - Ambient conditions"

•

Relative humidity 20 … 85 %

With instrument weights of more than 18 kg (39.68 lbs) suitable and

approved equipment must be used for lifting and carrying.

Application area

Functional principle

Packaging

Transport

Transport inspection

Storage

Storage and transport

temperature

Lifting and carrying

10

3 Product description

WEIGHTRAC 31 • Four-wire 4 … 20 mA/HART

42374-EN-210311

3.4 Accessories

The display and adjustment module is used for measured value indi-

cation, adjustment and diagnosis.

The integrated Bluetooth module (optional) enables wireless adjust-

ment via standard adjustment devices.

The interface adapter VEGACONNECT enables the connection of

communication-capable instruments to the USB interface of a PC.

The VEGADIS 81 is an external display and adjustment unit for VEGA

plics

®

sensors.

VEGADIS 82 is suitable for measured value indication and adjustment

of sensors with HART protocol. It is looped into the 4 … 20 mA/HART

signal cable.

The electronics module PT30… is a replacement part for radiometric

sensors WEIGHTRAC 31.

It is located in the large electronics and connection compartment.

The electronics module can only be exchanged by VEGA service

technician.

The supplementary electronics module PROTRAC.ZE… is a replace-

ment part for radiometric sensors WEIGHTRAC 31.

It is located in the lateral adjustment and connection compartment.

If you have ordered WEIGHTRAC 31 without a measuring frame, a

basic mounting set is enclosed with the instrument. It includes every-

thing needed to fasten the measuring tube reliably.

The corresponding measuring frame and mounting accessories can

be ordered optionally.

Use a tachometer for detection of the belt speed. The tachometer can

be connected to the input of the WEIGHTRAC 31.

The reference absorber is a test facility for the WEIGHTRAC 31. It

is suitable for reference measurement on conveyor belts and screw

conveyors. A certain measured value can be exactly reproduced for

test purposes when a conveying system is empty.

In order to exclude external interference radiation, you can mount a

gamma modulator in front of the source holder. This allows reliable

measurement even when interference radiation occurs.

PLICSCOM

VEGACONNECT

VEGADIS 81

VEGADIS 82

Electronics module -

PT30

Supplementary electron-

ics module - PROTRAC.

ZE

Basic mounting set

Measuring frame for

mounting

Tachometer

Reference absorber

Gamma modulator

11

3 Product description

WEIGHTRAC 31 • Four-wire 4 … 20 mA/HART

42374-EN-210311

Fig. 3: Gamma modulator (optional) for uninterrupted measurement even with

interference radiation

1 Gamma modulator (mounted on the source holder)

For ambient temperatures up to 120 °C (248 °C) the gamma modula-

tor is optionally available with water cooling.

Anynumberofdevicescanbesynchronized.Tosynchronizeseveral

gamma modulators, you need a controller.

3.5 Corresponding source container

An isotope in a suitable source container (e.g. SHLD-1) is the prereq-

uisite for a radiometric measurement setup.

The handling of radioactive substances is regulated by law. The radia-

tion protection rules of the country in which the system is operated

applyrstandforemost.

In Germany, for example, the current radiation protection ordinance

(StrlSchV) based on the Atomic Energy Law (AtG) applies.

The following points are important for measurement with radiometric

methods:

A handling permit is required for operation of a system using gamma

rays.Thispermitisissuedbytherespectivegovernmentoceorthe

responsibleauthority(inGermany,forexample,ocesforenviron-

mental protection, trade supervisory boards, etc.)

Youcanndfurtherinstructionsintheoperatinginstructionsmanual

of the source container.

Handling permit

12

3 Product description

WEIGHTRAC 31 • Four-wire 4 … 20 mA/HART

42374-EN-210311

When handling radioactive substances, unnecessary radiation

exposure must be avoided. An unavoidable radiation exposure must

be kept as low as possible. Take note of the following three important

measures:

1 2 3

Fig. 4: Measures for protection against radioactive radiation

1 Shielding

2 Time

3 Distance

Shielding: Provide good shielding between the source and yourself

as well as all other persons. Special source containers (e.g. SHLD-1)

as well as all materials with high density (e.g. lead, iron, concrete,

etc.)provideeectiveshielding.

Time: Stay as short a time as possible in radiation exposed areas.

Distance: Your distance to the source should be as large as possible.

The local dose rate of the radiation decreases in proportion to the

square of the distance to the radiation source.

Theplantoperatormustappointaradiationsafetyocerwiththe

necessary expert knowledge. He is responsible for ensuring that the

radiation protection ordinance is complied with and for implementing

all radiation protection measures.

Control areas are areas in which the local dose rate exceeds a certain

value.Onlypersonswhoundergoocialdosemonitoringareallowed

intothesecontrolareas.Youcanndtherespectivelyvalidlimitvalues

for control areas in the guideline of the respective authority (in Ger-

many, for example, the radiation protection ordinance).

We are at your disposal for further information concerning radiation

protection and regulations in other countries.

General instructions for

radiation protection

Radiationsafetyocer

Control area

13

4 Mounting

WEIGHTRAC 31 • Four-wire 4 … 20 mA/HART

42374-EN-210311

4 Mounting

4.1 General instructions

The source container is part of the measuring system. In case the

source container is already equipped with an active isotope, the

source container must be locked before mounting.

Danger:

Before mounting; make sure that the source is securely closed. Use

a padlock to secure the source container in the closed condition and

prevent it from being inadvertently opened.

Protect your instrument against moisture ingress through the following

measures:

•

Use a suitable connection cable (see chapter " Connecting to

power supply")

•

Tighten the cable gland or plug connector

•

Lead the connection cable downward in front of the cable entry or

plug connector

This applies mainly to outdoor installations, in areas where high

humidity is expected (e.g. through cleaning processes) and on cooled

or heated vessels.

Note:

Make sure that during installation or maintenance no moisture or dirt

can get inside the instrument.

To maintain the housing protection, make sure that the housing lid is

closed during operation and locked, if necessary.

Note:

For safety reasons, the instrument must only be operated within the

permissibleprocessconditions.Youcannddetailedinformationon

the process conditions in chapter " Technical data" of the operating

instructions or on the type label.

Hence make sure before mounting that all parts of the instrument ex-

posed to the process are suitable for the existing process conditions.

These are mainly:

•

Active measuring component

•

Processtting

•

Process seal

Process conditions in particular are:

•

Process pressure

•

Process temperature

•

Chemical properties of the medium

•

Abrasionandmechanicalinuences

Switchosource

Protection against mois-

ture

Process conditions

14

4 Mounting

WEIGHTRAC 31 • Four-wire 4 … 20 mA/HART

42374-EN-210311

Metric threads

In the case of instrument housings with metric thread, the cable

glands are screwed in at the factory. They are sealed with plastic

plugs as transport protection.

You have to remove these plugs before electrical connection.

NPT thread

In the case of instrument housings with self-sealing NPT threads, it is

not possible to have the cable entries screwed in at the factory. The

free openings for the cable glands are therefore covered with red dust

protection caps as transport protection.

Prior to setup you have to replace these protective caps with ap-

proved cable glands or close the openings with suitable blind plugs.

The suitable cable glands and blind plugs come with the instrument.

4.2 Mounting instructions

Note:

During the planning, our specialists will analyse the conditions of the

measurement loop to dimension the isotope accordingly.

Yougeta"SourceSizing"documentspecifyingtherequiredsource

activity and containing all relevant mounting information for your

measuring point.

Youmustfollowtheinstructionsinthis"SourceSizing"documentin

addition to the following mounting instructions.

The following mounting information is applicable as long as there is

nothingelsespeciedinthe"SourceSizing"document.

You can position and mount WEIGHTRAC 31 in the measuring frame

from both sides.

Direct the exit angle of the source container to the WEIGHTRAC 31.

Mountthesourcecontaineratthespecieddistancetotheconveyor

belt. Secure the area with a safety fence and protective grating so that

no one can reach into the dangerous area.

Youcanndinformationonprotectivebarriersandthemounting

of the corresponding source container in the operating instructions

manual of the source container.

If you have ordered WEIGHTRAC 31 without measuring frame, a

basic mounting set is enclosed with the instrument.

Determine the mounting position of the sensor in advance.

1. Fasten the mounting bracket (6) to your conveyor belt.

You can either weld the mounting bracket (6) to your system or

fasten it with screws through the two ø9 mm (0.35 in) holes.

2. Place two clamp collars (4) onto the premounted mounting brack-

ets (6).

Cable glands

Installation position

Basic mounting set

15

4 Mounting

WEIGHTRAC 31 • Four-wire 4 … 20 mA/HART

42374-EN-210311

1

2

3

4

5

4

2

6

7

Fig. 5: Mounting of the sensor with the basic mounting set

1 Screws M6 x 120 (4 pieces)

2 Wedge lock washer M6 Nordlock (8 pieces)

3 Cover plate (2 pieces)

4 Clamp collar (4 pieces) PA

5 Sensor

6 Mounting bracket

7 Nut M6 (4 pieces)

Note:

Mount the instrument housing of the sensor on an easily accessible

side of the conveyor belt so that the instrument is easily accessible for

operation and service.

3. Move the sensor (5) laterally beneath the conveyor belt and place

the sensor in the two clamp collars (4).

Position the measuring width of the sensor below the conveyor

belt as close as possible to the center. Make sure that there is

sucientdistancebetweensensorandconveyorbeltwhenthe

belt is loaded.

4. Place the other two clamp collars (4) according to the illustration

above the clamp collars that are already in place (4).

5. Place a metallic cover plate (3) according to the illustration on

each upper clamp collar (4).

16

4 Mounting

WEIGHTRAC 31 • Four-wire 4 … 20 mA/HART

42374-EN-210311

6. Insert the screws (1), each with one wedge lock washer (2),

through the clamp collars (4).

7. Place a wedge lock washer (2) from below on each screw (1) and

screw one nut (7) onto each screw.

8. Align the clamp collars (4) and tighten the nuts (7) evenly with

8 Nm (5.9 lb ft).

9. Check if the sensor (5) is fastened correctly.

- Conveyor belts

Mount the measuring frame in such a way that the measurement tube

of WEIGHTRAC 31 is below the conveyor belt (tight span).

Keep a distance of at least 10 mm (0.4 in) between the conveyor belt

and the measurement tube of WEIGHTRAC 31.

- Screw conveyors

Mount the measuring frame at a position on the spiral conveyor where

the product is transported steadily. Avoid places where the product

accumulates or falls back over the worm shaft.

- Chain conveyors

When mounting the WEIGHTRAC 31 on a chain conveyor, the instal-

lation angle is very important for optimal irradiation.

Followtheinstructionsinthe"SourceSizing"document.

Mounting of the measuring frame (optional)

The measuring frame with mounting accessories can be selected as

an option. If you have ordered WEIGHTRAC 31 with measuring frame,

then proceed as follows.

Mounting - Crossbeam

Before fastening the support stands, we recommend premounting the

measuring frame. By doing this you can easily lay out the holes for

fastening the unit to the conveyor belt.

To mount the measuring frame you need a torque wrench (45 Nm or

8Nm)andtwosocketwrenchesofsize16and10.

1. Placethecrossbeam(4)ontheupperholdingxturesofthetwo

support stands (6).

Make sure that the crossbeam (4) has an excess length of ap-

prox. 30 mm on both sides.

Measuring frame (op-

tional)

17

4 Mounting

WEIGHTRAC 31 • Four-wire 4 … 20 mA/HART

42374-EN-210311

1

2

3

4

2

5

6

Fig. 6: Mounting the crossbeam

1 Screws M10 x 40 (12 pcs.)

2 Wedge lock washer M10 Nordlock (24 pieces)

3 Crossbeam (1 piece)

4 Toe clamps (4 pieces)

5 Nut M10 (12 pieces)

6 Support stand (2 pieces)

2. Place the four clamping claws (4) with the corrugation downwards

into the crossbeam (3).

3. Insert the screws (1) with one wedge lock washer (2) through the

clamping claws (4).

4. Place a wedge lock washer (2) from below on each screw (1) and

screw one nut (5) onto each screw.

5. Alignthecrossbeam(3)withtheupperholdingxturesofthe

support stands (6) and tighten the nuts (5) evenly with 45 Nm

(33.2 lb ft).

Mounting - Support stand

1. Place the premounted measuring frame above the conveyor belt

and determine a suitable position for mounting the support stands

(6).

Mount the measuring frame as well centered as possible and

at an angle of 90° above the conveyor belt. Keep enough lateral

distance to the conveyor belt.

18

4 Mounting

WEIGHTRAC 31 • Four-wire 4 … 20 mA/HART

42374-EN-210311

2. Drill the through-holes for the support stands (6) according to the

following drilling plan.

The through-holes in the support stands (6 in each) are suitable

forscrewsofsizeM10.

The screws (14) and the washers (15) for fastening on the con-

veyor belt are not included in the scope of delivery.

120 mm

(4.72")

15 mm

(0.59")

150 mm

(5.91")

15 mm

(0.59")

270 mm

(10.63")

300 mm

(11.81")

ø 12 mm

(0.47")

Fig. 7: Drilling plan for support stands

3. Use suitable washers (15) for mounting the support stands (6).

14

15

Fig. 8: Mounting the support stands

14 Screw M10 (24 pieces) - provided by the customer

15 Washer M10 (24 pieces) - provided by the customer

4. Tighten the screws (14) evenly with 45 Nm (33.2 lb ft).

19

4 Mounting

WEIGHTRAC 31 • Four-wire 4 … 20 mA/HART

42374-EN-210311

Mounting - Sensor

1. Place two of the clamp collars (11) on the fastening brackets of

the support stands (6).

8

9

10

11

13

11

9

12

Fig. 9: Mounting the sensor in the measuring frame

8 Screws M6 x 120 (4 pieces)

9 Wedge lock washer M6 Nordlock (8 pieces)

10 Cover plate (2 pieces)

11 Clamp collar (4 pieces)

12 Nut M6 (4 pieces)

13 Sensor

Note:

Mount the instrument housing of the sensor on an easily accessible

side of the conveyor belt so that the instrument is easily accessible for

operation and service.

2. Insert the sensor (13) laterally into the measuring frame beneath

the conveyor belt and place the sensor in the two clamp collars

(11).

Position the measuring width of the sensor below the conveyor

belt as close as possible to the center. Make sure that there is

20

4 Mounting

WEIGHTRAC 31 • Four-wire 4 … 20 mA/HART

42374-EN-210311

sucientdistancebetweensensorandconveyorbeltwhenthe

belt is loaded.

3. Place the other two clamp collars (11) according to the illustration

above the clamp collars that are already in place (11).

4. Place a metallic cover plate (10) according to the illustration on

each upper clamp collar (11).

5. Insert the screws (8), each with one wedge lock washer (9),

through the clamp collars (11).

6. Place a wedge lock washer (9) from below on each screw (8) and

screw one nut (12) on each of the screws.

7. Align the clamp collars (11) and tighten the nuts (12) evenly with

8 Nm (5.9 lb ft).

8. Check if the sensor (13) is fastened correctly.

Mounting - Source container

1

7

5

2

Fig. 10: Mounting the source container on the measuring frame

1 Screw M10 x 65 (4 pieces)

2 Wedge lock washer M10 Nordlock (8 pieces)

5 Nut M10 (4 pieces)

7 Source holder (SHLD-1)

1. Place the closed and locked source container (7) from above onto

the measuring frame.

The source container is very heavy. Therefore use a suitable lifting

device. For this purpose the source container is equipped with a

suitable eye-bolt for a lifting hook, etc.

Note:

Select the alignment of the source holder so that the rotary mecha-

nism of the source holder is located on the easily accessible side of

the conveyor belt. This makes the rotary mechanism easily accessible

Page is loading ...

Vega WEIGHTRAC 31 Operating instructions

This manual is also suitable for

Vega WEIGHTRAC 31 Operating instructions

Related papers

Other documents