Premier ED-5189PRO User manual

INSTRUCTION MANUAL

PROFESSIONAL BLENDER

ED-5189PRO

DEAR CUSTOMER

In order to achieve the best performance of your product, please read this instruction

manual carefully before using, and keep it for future reference.

If you need extra support, please write to [email protected]

INSTRUCTION MANUAL

Safety Precautions .........................................................................2

Parts Description ............................................................................3

Control Panel .................................................................................. 4

How to Use .....................................................................................4

Lid, Measuring Cup, Seal Ring ....................................................... 8

Cleaning & Storage ........................................................................8

Notice for Operation .......................................................................8

Circuit Diagram & Specications ....................................................9

PREMIER CUSTOMER SERVICE

NOTE

This unit may be submitted to changes in specications, characteristics and/or operation

without prior notice to the user, in order to continue improving and developing its technol-

ogy.

Venezuela : 0800 – ELECTRIC (353-2874)

Panama : 300-5185

Website : www.premiermundo.com

E-mail : [email protected]

SAFETY PRECAUTIONS

• Before plugging in the appliance, check that the electrical rating shown on the rating

plate corresponds with your household electricity supply.

• Never immerse the unit base of the appliance in water or other uid, nor rinse it under

the tap, to avoid risk of short-circuit or electric shock. If there is water inside the unit

base, please contact Authorized Service Agent.

• Never put the power cord or plug into water for cleaning. Do not wipe the plug prongs

with damp cloth, nor plug in with wet hands.

• Plug the appliance to the wall outlet properly & securely. Loose plug may lead to

overheat or electric shock.

• If the power cord is damaged, it must be replaced by the manufacturer or its service

agents or similary qualied electricians in order to avoid a hazard.

• Never let the appliance unattended.

• Keep hands and utensils out of the container while the motor is running to prevent the

possibility of severe personal injury and/or damage.

• Do not run the appliance without loading in the blender jar..

• To prevent spillage, do not put liquid in the blender jar exceeding the MAX line.

• Do not expose the appliance to source of heat such as a radiator or sun shining

through a window. For good ventilation, do not place cloth underneath the appliance.

• Indoor use only. Do not use outdoor or for commerical purpose.

• Always operate with the lid in place. When processing hot beverages, properly secure

the lid and measuring cup in place to avoid scalding due to spraying of hot liquids.

• This appliance is not intended for use by persons (including children) with reduced

physical sensory or mental capabilities, or lack of experience and knowledge, unless

they have given supervision or instruction concerning use of the appliance by a

person responsible for their safety.

• Children should be supervised to ensure that they do not play with the appliance.

• Switch off the appliance and disconnect from supply before changing accessories or

approaching parts that move in use.

• Care is needed when handling cutting blades, especially when removing the blade

from the bowl, emptying the bowl and during cleaning.

• Unplug the power cord from the wall outlet when appliance is not in use, before putting

on or taking off parts, and before cleaning.

• If the motor has overheated, the temperature monitoring system will trigger and the

motor will stop. Switch off and unplug the appliance and let the motor cool down. The

motor temperature monitoring system resets after the blender is unplugged from wall

socket for 45 minutes. In this time, plug in the blender and it can be used again.

• The blade is very sharp, use caution when handling the blade. Do not attempt to

disassemble the blade assembly and touch any rotating parts.

• Any servicing should be performed by an authorized service representative. Do not

attempt to disassemble, repair or modify the appliance.

2

PART DESCRIPTION

3

Measuring Cup

Lid

Lid Silicone Ring

Blender Jug

Blade Assembly

Blade Mount

Blender Jug Mat

Drive Gear

Safety Switch

Motor unit

Transpar

ent sheet

Jog dial

Contr

ol Panel

LED Display

Power Cord

Anti-skid Rubber Foot

Fied Support

CONTROL PANEL

HOW TO USE

• Remark : Background of digital display is black, and all digits & icons are white.

Wide viewing angle.

• Power On Mode

When the product is energized, all lights are ON, the digital display shows full display

(Time Display is “88:88” and Speed Display is “8). After 1s, it enters Standby

Mode.

• Standby Mode

The digital display does not light on in Standby Mode. START/STOP (ON/OFF)

Button ashes red light. All other icons are off. Press any button to enter the Ready

Mode.

• Ready Mode

When the product is in Standby Mode, it will enter Ready Mode if any button is

pressed.

When the product is in Ready Mode, it will resume back to Stand-by Mode after 3

minute idle time.

• Ready mode – Time Display is “00:30” and the Speed Display is “3”. Button

ashed red light. Pulse Button white light ON, default setting is Manual Status and

the Manual Button ashes white light. All other icons white light ON.

Ready Mode is shown below :

• Instruction to Button Indication Graphics

4

Manual Button

Program Button

3 on left, 3 on right

Time Setting

Speed Display

Time Display

START/STOP (ON/OFF) Button

Selection Dial (can turn

clockwise & anticlockwise

Pulse Button

HOW TO USE

• Time Setting Buttons (

/

)

When the time is within 1 minute, “01:00”, press once increases 5 seconds,

and press once decreases 5 seconds. When the time is more than 1 minute

“01:00”, press once increases 10 seconds, and press once

decreases 10 seconds.

• After keep pressing

for 3 seconds, the buzzer will beep, and the time

display will increase or decrease 5 seconds at the rate 3 ash/second when the time

is within 1 minute. If the time is more than 1 minute, the time display will increase

or decrease 10 seconds at the rate 3 ash/second. The buzzer will beep on every

pressing of the button.

• The longest time setting is “ ” (10:00). When the time is set to “ ”, it

does not operate. It can work continuously by adjusting the cyclic Time Setting as

illustrated below :

00:00 10:00 Remark :

- + 1.In operation 00:00-10:00. 10:00-00:00 repeat

2.Not in operation 00:00-10:00. 10:00-00:00 can repeat

Remark : When the product is in operation, the timer countdowns in time interval of

1 second unit it shows “ ”, and then the product stops.

• Speed Setting

(Speed+,Speed-)

Press

or

to increase or decrease the speed by 1 setting. The

buzzer will beep on every pressing of the button. The sequence of the speed setting

is “ 1, 2, 3, 4, 5, 6, 7, 8, 9, H “ and it cannot be adjusted in cycles (i.e. press

button in Speed H, the speed remains unchanged. User can only press to

decrease the speed. Similarly, press button in Speed 1, the speed also

does not change. User can only press to increase the speed.

(The buzzer will beep on every pressing of the button )

(The motor power, voltage and speed at 120V~60Hz input & no load condition

are shown below) :

Remark : Start up of every speed setting is soft start.

5

Time Display

HOW TO USE

6

Icon Function Procedure Display Lighting

Rinse

Speed H for 5s, stop for 2s.

Run the cycle 4 times. Preset display is 28s and

Speed H. All soft start.

Time & Speed

LED ashes in 0.5s

ON / 0.5s OFF cycles

Puree

Speed H for 3s, stop for 3s. Run the cycle 10

times. Then run in Speed H for 40s. Preset

display is 1m 40s and Speed H. All soft start.

Time & Speed

LED ashes in 0.5s

ON / 0.5s OFF cycles

Soup

Increase from Speed 1 to Speed 7 in 5s. Then

increase to Speed H in 5s. Keep in Speed H until

8min. Preset display is 8min and Speed 1. All

soft start.

Time & Speed

LED ashes in 0.5s

ON / 0.5s OFF cycles

Manual

This button ashes when the product starts up.

Preset display is 30s and Speed 3. All soft start.

Time & Speed

LED ashes in 0.5s

ON / 0.5s OFF cycles

Smoothie

Speed H for 8s, stop for 2s. Run the cycle 5

times. Preset display is 50s and Speed H. All

soft start.

Time & Speed

LED ashes in 0.5s

ON / 0.5s OFF cycles

Crush

Hard start in Speed H for 2s, stop for 4s. Run

the cycle 10 times. Preset display is 1min and

Speed H. All soft start.

Time & Speed

LED ashes in 0.5s

ON / 0.5s OFF cycles

Frozen

Speed H for 4s, stop for 2s. Run the cycle 10

times. Preset display is 1min and Speed H. All

soft start.

Time & Speed

LED ashes in 0.5s

ON / 0.5s OFF cycles

• START/STOP(ON/OFF) Button

• This button is to start the operation. After a function is selected, the product will

only operate after pressing the button. Press again to stop operation. In

Ready Mode and Standby Mode, this button ashes red light. It display green light

in operation.

• Manual Button

After pressing this button, the Speed Setting / and Time Setting

/ can be adjusted. Both settings can also be adjusted during operation.

In this mode, the Manual Button ashes white light.

• Pulse Button

This is Pulse Button, and it can only operate when the button is kept pressing. The

motor runs in full speed (i.e. Speed H) with a soft start. This button has no time limit

and overrides the program functions. That means when the Pulse Button is pressed

on hold, the product directly enter the Speed H. The product resumes Ready Mode

upon the release of this button. This button keeps light on white light.

• Program Buttons , , , , & , total 6 programs. The descriptions of each

program are mentioned below :

• Use Selection Dial to select the desired program, the corresponding icon will ash.

Then press the “ ” Button to run the selected program, and the “ ” Button

lights on green LED. Press the “ ” again during operation will stop the program.

The product resumes Ready Mode.

• If the Time / Speed Setting is adjusted during operation in any preset program. The

product will switch to mode, and short-cut button light will change to Button.

HOW TO USE

• Instruction of All Working Modes

• Manual Mode

Use the Selection Dial to select the icon. The adjust the Time Setting and Speed

Setting. The press Button to start operation. If the user wants to stop the

operation, press the Button again. The product stops running and resumes

Ready Mode.

• Preset Program Mode

There are 6 preset programs for various food selections. Turn the Selection Dial to

the desired program, the display will show in the format as section 2.6 described.

Finally press the Button to run the selected program (refer to section 2.6).

• Total Working Time Display

In the Ready Mode, press and hold the Button, and then keep pressing

Button for 5 seconds. The Time Display will show the total accumulated working

time of the motor (unit: in minute) for 3 seconds. Then the product resumes Ready

Mode. The product counts the total working time in seconds, and displays in minutes.

The maximum displayable time is 99999 minutes. The Speed Display represent the

digits in 10000.

e.g total working time is 6528 minutes : e.g. total working time is 26528 minutes :

• The Speed Buttons

, Time Buttons

& Pulse Button

light on white light. Button light on red light in Ready Mode, and green light in

operation. The button selected program ashes during operation, and other icons

light on white light. Buzzer beeps in each pressing of the button.

• Operation Flow

When the product is energized, it enters Standby Mode (refer to section 1.1)

A. Turn the Selection Dial to select any preset program, the corresponding icon

ashes and the product operate in the selected procedures (refer to section 2.6)

B. In Manual Mode, press Button to start operation.

During operation, press Button will stop the operation, and the product resumes

Ready Mode.

• Rating : Motor rated power is 1400W

• Other Requirements :

1. Normal working voltage : AC 120V~60Hz (PCBA runs normally in 90V~130V)

2. Normal working humidity : 20% ~ 90%

3. Normal working temperature : -5°C ~ 55°C

4.Storage & transportation temperature of PCB is -20°C ~ 70°C. Working

temperature cannot exceed 55°C. It needs anti-shock protection.

7

CLEANING & STORAGE

• Unplug the appliance from the wall outlet.

• Do not immerse the motor unit or power cord into water or other liquids.

• Clean surface of the blender jar with soft cloth or spongy. The measuring cup and

the seal ring can be disassembled for cleaning.

• The blender jar can be rinsed with water. It can also be cleaned by lling 2 cups of

water in the blender jar, close the lid and then operate the blender in Pulse mode.

Then pour out the water and dry it with soft cloth.

• After cleaning, put the blender jar on the side or upside down (Note 1) to dry. Do not

immerse the whole jar in water.

• Clean the motor unit by soft cloth. NEVER put it in water.

Note 1 : If put the blender jar in upside down position, please remove the residual

water by dry cloth. Do not leave it close to the sink or basin to avoid water

spraying to the bottom part of the jar. This may cause the rusting of the

bearing and hence affecting the performance of the blender.

• If the motor is dragged to a low speed since the food is too thick or there is too less

liquid in the jar, and operates for a proloned period, the temperature monitoring

system will trigger and stop the operation of the motor. In this case, unplug and put

the blender to a place with good ventilation to cool down the motor temperature for

45 minutes. The system will reset and the blender can be used again.

• During operation, close the lid tightly to avoid scalding due to spraying of hot liquids.

• Keep hands and utensils out of the container while the motor is running to prevent

the possibility of severe personal injury and/or damage.

• In making hot beverage such as soybean milk, hot soup, please check whether the

lid is secured tightly to the jar to prevent it from falling. It is advisable to start the

operation at low speed setting and increase the speed gradually, or use the Pulse

Drive mode.

• When making sauces (eg. Almond sauce, jam and sesame sauce), stuffing and

nuts,put in between 2 and 3 cups of ingredients. The amount should neither be too

large or too little. Keep the blending time below 2 min. to prevent any burnt smell

due to overheating. Too much ingredients may lead to overlaoding and overheating

of the motor. In this case, wait till the motor temperature fall before operating again.

• Please put liquid and soft food before putting in hard food or ice cubes.

• When the operation finishes, please wait until the blade assembly comes to a

complete stop before taking up the blender jar. Otherwise, the Drive Gear may be

damaged.

NOTICE FOR OPERATION

8

LID, MEASURING CUP, SEAL RING

• Insert the measuring cup to the lid by aligning the two taps to the grooves of the lid

and twist to lock it at the bottom position. Then push in the lid to the blender jar to

close it. To open, pull up the ap of the lid.

• The seal ring is detachable from the lid for easy cleaning.

NOTICE FOR OPERATION

• If you feel a scorch smell from the blender, stop the operation immediately. It may be

caused by the abrasion at the rubber cushion base if it is not properly assembled.

• l When blending thick and sticky food using high speed, please start the operation

at low speed. If the turning is still idle, disconnect the power and stir the blender jar

using a rubber stirrer to drive out the air capsule trapped in the food. Then close the

lid and switch on to proceed the operation

• l Do not operate for more than 10 minutes at a time.

Product : COMMERCIAL BLENDER

Model : ED-5189PRO

Rating : 120V ~ 60Hz

Max Power : 1400W

Dimensions : 225mm (L) x 225mm (W) x 525mm (H)

SPECIFICATIONS

9

ACL

M2

PCB

Non self-resetting thermal protector (Tf130)

MBL16 9540 Motor

ACN

M1

120V~60Hz

Interlock Switch

CIRCUIT DIAGRAM

P-7

P-8

P-9

P-10

P-11

P-12

P-13

P-14

P-15

Page is loading ...

Premier ED-5189PRO User manual

Premier ED-5189PRO User manual

Related papers

Other documents