Orbit DripMaster Vegetable Garden Soaker System Step-By-Step Manual

Brand: Orbit

Model: DripMaster Vegetable Garden Soaker System

Type: Step-By-Step Manual

Orbit DripMaster Vegetable Garden Soaker System is an expandable watering system that can be used for both vegetable gardens and general landscape watering. The kit comes with everything you need to get started, including a 3-in-1 faucet adapter, tubing, stakes, and drippers.

The soaker system is easy to set up and use. Simply attach the faucet adapter to your outdoor faucet or garden hose, roll out the tubing, and insert the drippers into the tubing. The drippers are designed to slowly release water, providing deep root watering without waste or runoff.

The Orbit DripMaster Vegetable Garden Soaker System is a great way to water your plants efficiently and effectively. It is perfect for both small and large gardens, and can be customized to fit your specific needs.

VEGETABLE GARDEN

SOAKER SYSTEM

STEP-BY-STEP GUIDE

This expandable Vegetable Garden Soaker System is also ideal for

general landscape watering. To expand your system, simply purchase

additional kits and connect them together or purchase additional tubing

and fittings separately. Up to 35 soaker lines can run off one 1/2”

distribution tube.

PN 67527-24 Rev B

Orbit

Irrigation Products, Inc.

North Salt Lake, UT 84054 USA

www.orbitonline.com | 1-800-488-6156

Printed in USA

trademarks of respective manufacturers listed.

KIT CONTENTS

1 3-in-1 faucet adapter—pressure

regulator, filter and 1/2” drip tube

adapter

5 1/2” tubing hold down stake

1 1/2” tubing end cap

12 4 gallons per hour flag dripper

1 hole punch

50’ 1/4” soaker tubing

24 1/4” tubing hold down stake

12 1/4” tubing end plug

1 pipe thread to hose thread adapter

*Note: 1/2” distribution tubing is not included in this kit. Be sure to purchase/use

1/2” distribution tubing with an outside diameter of .690 or larger.

2 3

4 5

Follow these seven steps to

create a plant-enhancing,

water-conserving,

and time-saving system.

(a) Attach the 3-in-1 faucet

adapter to an outdoor

faucet or garden hose.

This contains a pressure

regulator, removable filter

and 1/2” drip tubing adapter.

(b) Push 1/2” tubing (not

included) into adapter.

Roll out 1/2” distribution

tubing and secure with

1/2” stakes.

Cap the 1/2” distribution line

with 1/2” tubing end fitting.

(a) Using the hole punch, punch

a hole in the 1/2” distribution

line where you want the first

soaker line to begin.

(b) Insert the flag dripper as

shown in figure 4.

(a) Attach 1/4” soaker tubing

to the flag dripper.

(b) Run 1/4” soaker out from the

flag dripper, up to 15’,

and secure with stakes.

Cut tubing from roll with

garden clippers.

until system is completed.

Remove 1/2” tubing end

cap and flush water

through the system for

one minute.

(a) Reinstall 1/2” tubing end

cap.

(b) Insert a 1/4” end plug at

the end of each soaker

line.

Tips for successful soaker layout

• Soaker tubing run on level

ground provides the most even

water distribution.

• Lay soaker straight, loop

around plants, or wind through

closely planted areas.

Soaker tubing waters slowly, providing deep root

watering and helping eliminate waste and runoff.

For best results, water between 1/2 hour (6-8” root

depth) and 4 hours (5’ root depth).

SOAKER SYSTEM IS READY FOR USE!

Orbit DripMaster Vegetable Garden Soaker System Step-By-Step Manual

Orbit DripMaster Vegetable Garden Soaker System Step-By-Step Manual

Orbit DripMaster Vegetable Garden Soaker System Step-By-Step Manual

Related papers

Other documents