Kingston Technology KVR18L13Q4/32 Datasheet

Kingston Technology
Brand
Kingston Technology
Model
KVR18L13Q4/32
Category
Memory modules
Type
Datasheet

Kingston Technology KVR18L13Q4/32 32GB DDR3 SDRAM memory module is a high-performance, high-density memory module designed for use in servers, workstations, and other high-end computing applications. It features a capacity of 32GB, a speed of 1866MHz, and a latency of CL13. This makes it ideal for applications that require fast data access and high bandwidth, such as video editing, 3D rendering, and gaming.

The KVR18L13Q4/32 is also equipped with a number of features that enhance its performance and reliability. These features include:

  • JEDEC standard 1.5V power supply: This ensures compatibility with a wide range of motherboards and systems.

Kingston Technology KVR18L13Q4/32 32GB DDR3 SDRAM memory module is a high-performance, high-density memory module designed for use in servers, workstations, and other high-end computing applications. It features a capacity of 32GB, a speed of 1866MHz, and a latency of CL13. This makes it ideal for applications that require fast data access and high bandwidth, such as video editing, 3D rendering, and gaming.

The KVR18L13Q4/32 is also equipped with a number of features that enhance its performance and reliability. These features include:

  • JEDEC standard 1.5V power supply: This ensures compatibility with a wide range of motherboards and systems.
DESCRIPTION
Document No. VALUERAM1444-001.A00 07/02/14 Page 1
SPECIFICATIONS
*Power will vary depending on the SDRAM and
Register/PLL used.
Continued >>
kingston.com
FEATURES
ValueRAM’s KVR18L13Q4/32 4G x 72-bit (32GB) DDR3-1866
CL13 SDRAM (Synchronous DRAM), 4Rx4, load reduced, ECC
memory module, based on thirty-six DDP 2G x 4-bit
components. The SPD is programmed to JEDEC standard
latency DDR3-1866 timing of 13-13-13 at 1.5V. This 240-pin
LRDIMM uses gold contact fingers. The electrical and
mechanical specifications are as follows:
• JEDEC standard 1.5V (1.425V ~ 1.575V) Power Supply
• VDDQ = 1.5V (1.425V ~ 1.575V)
• 933MHz fCK for 1866Mb/sec/pin
• 8 independent internal banks
• Programmable CAS latency: 13, 11, 10, 9, 8, 7, 6
• Programmable Additive Latency: 0, CL - 2, or CL - 1 clock
• 8-bit pre-fetch
• Burst Length: 8 (interleave without any limit, sequential with
starting address “000” only), 4 with tCCD = 4 which does not
allow seamless read or write (either on the fly using A12 or
MRS)
• Bi-directional Differential Data Strobe
• Internal (self) calibration: Internal self calibration through ZQ
pin (RZQ: 240 ohm ± 1%)
• On Die Termination using ODT pin
• On-DIMM thermal sensor (Grade B)
• Average Refresh Period 7.8us at lower than TCASE 85°C,
3.9us at 85°C < TCASE < 95°Cº
• Asynchronous Reset
• PCB: Height 1.195” (30.35mm), double sided component
CL(IDD)
Row Cycle Time (tRCmin)
Refresh to Active/Refresh
Command Time (tRFCmin)
Row Active Time (tRASmin)
Maximum Operating Power
UL Rating
Operating Temperature
Storage Temperature
13 cycles
47.91ns(min.)
260ns(min.)
34ns(min.)
11.070 W*
94 V - 0
0
o
C to +85
o
C
-55
o
C to +100
o
C
Memory Module Specifi cations
KVR18L13Q4/32
32GB 4Rx4 4G x 72-Bit PC3-14900
CL13 Load Reduced DIMM
Memory Module Specifi cations
Document No. VALUERAM1444-001.A00 Page 2
MODULE DIMENSIONS
kingston.com
Units : Millimeters
1.00
0.2 ± 0.15
2.50 ± 0.20
Detail B
5.00
Detail A
1.50±0.10
0.80 ± 0.05
3.80
2.50
9.9
0.6
Detail C
1.27
A
B
47.00
71.00
54.675
C
133.35 ± 0.15
30.35 ± 0.15
Max 4.8
MODULE DIMENSIONS
Document No. VALUERAM1444-001.A00 Page 3
kingston.com
133.15 ± 0.2
4.65
± 0.12
130.45 ± 0.15
127 ± 0.12
25.6 ± 0.15
Green Line : TIM Attach Line
1+0/ -0.3
0.65 ± 0.2
R
0
.
2
R0.1
1
25.6 ± 0.15
0.15
1.3
1.3
2
2 ± 0.1
2.6 ± 0.2
Reg. pedestal line
Outside
Inside
Green Line : TIM Attach Line
Outside
Inside
31.4
9.26
1. FRONT PART
2. BACK PART
  • Page 1 1
  • Page 2 2
  • Page 3 3

Kingston Technology KVR18L13Q4/32 Datasheet

Kingston Technology
Brand
Kingston Technology
Model
KVR18L13Q4/32
Category
Memory modules
Type
Datasheet

Kingston Technology KVR18L13Q4/32 32GB DDR3 SDRAM memory module is a high-performance, high-density memory module designed for use in servers, workstations, and other high-end computing applications. It features a capacity of 32GB, a speed of 1866MHz, and a latency of CL13. This makes it ideal for applications that require fast data access and high bandwidth, such as video editing, 3D rendering, and gaming.

The KVR18L13Q4/32 is also equipped with a number of features that enhance its performance and reliability. These features include:

  • JEDEC standard 1.5V power supply: This ensures compatibility with a wide range of motherboards and systems.
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents