Auna Pure Precision - 10032938 Owner's manual

Page is loading ...

15

EN

Dear Customer,

Congratulations on purchasing this equipment.

Please read this manual carefully and take care of

the following hints to avoid damages. Any failure

caused by ignoring the items and cautions men-

tioned in the instruction manual are not covered

by our warranty and any liability. Scan the QR

code to get access to the latest user manual and

other information about the product.

CONTENTS

Technical data 16

Safety instructions 16

Product overview 17

Installation 18

Connections 20

Getting started and operation 22

Connecting with a computer 24

Cleaning and care 24

Disposal considerations 25

16

EN

SAFETY INSTRUCTIONS

• Do not place anything on the turntable cover. Objects on the cover

might cause noise due to vibrations or fall o, especially during

playback.

• Avoid placing the unit in direct sunlight, close to a source of heat or in

other similar conditions. Do not place the unit on top of an amplier or

other equipment that might generate heat the exceeds the operating

temperature range of this unit. Doing so could cause discoloration,

deformation or malfunction.

• Do not move the unit during playback. During playback, the record

rotates. Do not lift or move the unit during playback. Doing so may

damage the record, the stylus, the cartridge or the unit.

• The voltage supplied to the unit should match the voltage as printed on

the rear panel. IF you are in any doubt regarding this matter, consult an

electrician.

TECHNICAL DATA

Item number 10032938

Power supply net adaptor Input: 100 - 240 V~ 50/60 Hz

Otuput: 15 V

Power cosumption Operation: 1,5 W

Standby: 1,5 W

Turntable

Platter diameter 12"

Driving method Belt drive

Speeds 33 1/3 45 U/min

S/N ratio 35 dB

17

EN

PRODUCT OVERVIEW

1 Pulley Cover

2 Belt

3 Aluminum platter

4 Wooden cabinet

5 Center Spindle

6 Counterweight

7 Anti skating

8 Cueing lever

9 Tone arm

10 33/45 RPM select switch

11 START/STOP Switch

12 Headshell

13 Hinge

18

EN

INSTALLATION

Platter installation

• Place it on a at surface.

• Install the platter.,

• Align the platter with the center spindle and install it.

• Place the large side of the hole down.

Loop the belt around the motor pulley.

Loop the included rubber belt around the outside of the platter, and then

loop the belt around the motor pulley.

• Be careful not to let the rubber becomes twisted.

• Rotate the platter several times to make sure that it is secure.

19

EN

Install the pulley cover

Align the small cutout in the pulley cover with the small protuberance on

the pulley, as shown in the instruction below. If these are not aligned, the

pulley cover will slant.

20

EN

CONNECTIONS

Item Function

1 Ground

2 Analog audio output jacks(L/R)

Output analog audio signals.

Please use a separately purchased

stereo RCA cable (L/R) to connect to

external equipment. The audio signal

can be changed by pressing the PHONO

/ EQ button (see 3).

3 PHONO-/ LINE-Auswahltaste

PHONO: Signals that have been

amplied by the built-in equalizer amp

are output from the analog audio output

jacks(L/R).

LINE: use this when connecting to

equipment that has AUX inputs.

Caution

Then set to ON, if connected to the PHONO inputs of an amplier, for example,

the output from speakers and headphones will be very loud, which could damage

equipment or harm hearing.

21

EN

4 PC encoding

Connect this to the USB port of a

computer to convert the audio signal

from this unit to digital and output it to

the computer.

5 DC input connector

After completing all other connections,

connect the included AC adapter to this

jack.

Conrm that the power plug of the AC

adapter is plugged into a power outlet.

Unplug the power cord from the outlet

when you are not planning to use the

unit for an extended period of time.

Do not use any AC adapter other than

the one included.

6 Power ON/OFF button

7 Feet

22

EN

GETTING STARTED AND OPERATION

Notes on record stylus

• Record styluses are precision parts, so handle them carefully to avoid

bending or damaging their tips. If a stylus becomes bent or damaged,

it might not be able to follow the audio groove precisely and could

damage records or cause another malfunction.

• If a stylus becomes dirty, use a commercially available stylus cleaner or

similar product to clean it.

• Do not rub the stylus tip forcefully with anything hard. Do not wipe the

stylus with thinner or other chemicals. Doing so could harm it.

Headshell

Electrical connections

23

EN

Playing records

• Press the Power ON/OFF button on the back of the unit to turn it on.

• Open the turntable cover slowly.

• Place a record on the turntable. When playing a 45 RPM large-hole

single record, use the included adapter.

• Set according to the rotation speed (RPM)of the record. The rotation

speed can be set to 33 1/3 or 45 RPM.

• Turn the START/STOP rotation knob to START to start the turntable.

• Move the tone arm clasp to the right to release the tone arm.

• Lift the cue lever.

• You can also leave the cue lever down and moved the raised tone arm

over the record and then lower the tone arm slowly to start playback.

• Move the tone arm to the edge of the record or the track where you

want to start playback.

• Lower the cue lever.

• Lower the tone arm slowly until the stylus touches the record and

playback begins. We recommend that you close the turntable cover

during record playback to avoid dust.

• Do not place anything on the turntable cover. Objects on the cover

might cause noise due to vibrations or fall o, especially during

playback.

• When playback nishes slightly lift the cue lever or the head-shell hook

and return the tone arm to its resting position.

• Turn the START/STOP rotation knob to STOP to stop the turntable.

Caution

• During playback, do not touch the tone arm or the rotating record.

• Do not stop turntable rotation during playback.

• During record playback, feedback could occur if the volume is too loud.

If this happens, lower the volume of the amplier.

24

EN

CONNECTING WITH A COMPUTER

• Connect this record player to a computer using a commercially-

available USB cable to convert audio signals from a record to digital

data and send them to the computer.

• Turn the computer on: con rm that the operating system is working

correctly. � Turn the record player on.

• When they are connected, the computer will automatically detact this

unit's USB port and identify it as "USB Audio CODEC".

• Turn the computer on: con rm that the operating system is working

correctly.

• Turn the record player on.

• When they are connected, the computer will automatically detect this

unit’s USB port and identity it as “USB Audio CODEC’’.

• To record audio from this record player using a computer, you must  rst

install software that can be used for audio recording on the computer.

Please download the software: Audacity as attached.

• Install Audacity software in your computer.

• Open the software.

• Click Append Record icon in the software: the encoding is going on. -

When  nish the encoding, click STOP icon.

• Open the Files icon in the software and save the project.

• The project can be exported in MP3 or other audio format as you like.

Reminder: When in encoding, please always select LINE mode, then you

can record a better-quality resource.

CLEANING AND CARE

• If the surface of the unit gets dirty, wipe it with a soft cloth or use

diluted mild liquid soap. Allow the surface of the unit to dry completely

before using.

• Do not use chemical cleaning cloths, thinner or similar substances as

they could damage the surface or the unit..

Warning: Danger of electric shock

For safety, turn the device o and disconnect the power cord from

the socket before cleaning.

25

EN

DISPOSAL CONSIDERATIONS

According to the European waste regulation 2012/19/EU this

symbol on the product or on its packaging indicates that this

product may not be treated as household waste. Instead it

should be taken to the appropriate collection point for the

recycling of electrical and electronic equipment. By ensuring

this product is disposed of correctly, you will help prevent

potential negative consequences for the environment

and human health, which could otherwise be caused by

inappropriate waste handling of this product. For more

detailed information about recycling of this product, please

contact your local council or your household waste disposal

service.

Declaration of Conformity

Producer: Chal-Tec GmbH, Wallstraße 16, 10179 Berlin.

Germany

This product is conform to the following European Directives:

2011/65/EU (RoHS)

2014/30/EU (EMC)

2014/35/EU (LVD)

Page is loading ...

Auna Pure Precision - 10032938, TT-Pure Owner's manual

Related papers

Other documents