1 DTP-64A
Screw Terminal
DTP-64A User’s Guide
CONTEC CO., LTD.
Thank you for purchasing the CONTEC product.
The DTP-64A is a screw terminal fastened with screws, which relays the I/O wirings of CONTEC
interface board or card with a 96-pin half-pitch connector.
The pins in the 96-pin half-pitch connector correspond to their respective terminals on the terminal
strips on a one-to-one basis, allowing you to easily connect the board to an external device via the
terminal strips.
Note: To connect a board/card to the accessory, you need the separately priced option cable.
Features
- A signal line from an external device can be connected to the terminal simply by using screws.
- The optional cable can be used to connect easily to the board/card.
Product Configuration List
This product is configured as follows. Be sure you have received all of the components listed. If any
components are missing or broken, contact the store where you purchased this product.
- Body…1 - User’s Guide (this guide)…1
- Warranty Certificate …1 - Serial number label …1
The option cable is not appended to the interface board/card and this product. Be sure to check the
manual or visit the CONTEC’s Web site of the board/card to be used and then buy an appropriate
cable.
CAUTION
DTP-64A User’s Guide
DTP-64A 2
External View and Dimensions
Figure 1. External View and Dimensions Figure 2. External Views and
Dimensions of Terminal Strip
DTP-64A Connections
Figure 3. DTP-64A Connections
(1) Connect the interface board/card and the product using the separately available option cable.
(2) Check the wiring destination of the product and wire the signal conductors from the external device.
You can easily connect the conductors to the terminals using the screws.
122
3-φ5
A48
B48
1605
107
7.5
170
CN1
A1
B1
B1
B3
B5
B7
B9
B2
B4
B6
B8
B10
B41
B43
B45
B47
B42
B44
B46
B48
A2
A4
A6
A8
A10
A1
A3
A5
A7
A9
A42
A44
A46
A48
A41
A43
A45
A47
24.6
15.3
[mm]
15.36
[mm]
3.5
13.97
1 2 3
15.24
5.08
External dimension tolerance : ±0.2mm
Contact pitch tolerance : ±0.05mm
Option cable
Product
Board
or
Card
Exlernal
device
Sigunal from/to
Exlernal machine
DTP-64A User’s Guide
3 DTP-64A
Wiring Diagram
Figure 4. Wiring Diagram
Specifications
Table 1. Specifications
Item Specifications
Terminal
Terminal type SMKDSP1.5/24-5.08 [mfd. by
PHOENIX CONTACT] equivalent
Number of terminals on
terminal strips
96 pin
Stripped length (mm) 6
Screws
M3
Connectable wire (mm
2
) Maximum connection range
: 0.13 - 1.5
Single wires : 0.5 - 1.5
Stranded wires : 0.5 - 1.5
Acceptable voltage 60V
Acceptable current 1A
Connector
Connector used PCR-E96MD+ [mfd. by HONDA
TSUSHIN KOGYO Co., LTD]
equivalent
Applicable connector PCR-E96FA [mfd. by HONDA
TSUSHIN KOGYO Co., LTD]
equivalent
Dimensions (mm) 170(W) x 122(H)
[49]
[1]
[96]
[48]
B48
B47
B46
B45
B44
B43
B42
B41
B40
B39
B38
B37
B36
B35
B34
B33
B32
B31
B30
B29
B28
B27
B26
B25
B24
B23
B22
B21
B20
B19
B18
B17
B16
B15
B14
B13
B12
B11
B10
B09
B08
B07
B06
B05
B04
B03
B02
B01
A48
A47
A46
A45
A44
A43
A42
A41
A40
A39
A38
A37
A36
A35
A34
A33
A32
A31
A30
A29
A28
A27
A26
A25
A24
A23
A22
A21
A20
A19
A18
A17
A16
A15
A14
A13
A12
A11
A10
A09
A08
A07
A06
A05
A04
A03
A02
A01
A48
A47
A46
A45
A44
A43
A42
A41
A40
A39
A38
A37
A36
A35
A34
A33
A32
A31
A30
A29
A28
A27
A26
A25
A24
A23
A22
A21
A20
A19
A18
A17
A16
A15
A14
A13
A12
A11
A10
A9
A8
A7
A6
A5
A4
A3
A2
A1
B48
B47
B46
B45
B44
B43
B42
B41
B40
B39
B38
B37
B36
B35
B34
B33
B32
B31
B30
B29
B28
B27
B26
B25
B24
B23
B22
B21
B20
B19
B18
B17
B16
B15
B14
B13
B12
B11
B10
B9
B8
B7
B6
B5
B4
B3
B2
B1
96pin Conector
Terminals
Terminals
The numbers in square brackets [ ] are
pin numbers designated by
HONDA TSUSHIN KOGYO CO., LTD.
DTP-64A User’s Guide
Copyright 2015 CONTEC CO., LTD. ALL RIGHTS RESERVED.
CONTEC CO., LTD. October 2015 Edition
3-9-31, Himesato, Nishiyodogawa-ku, Osaka 555-0025, Japan
Japanese http://www.contec.co.jp/
English http://www.contec.com/ NA00599 (LYLG124)
Chinese http://www.contec.com.cn/ 10262015_rev4 [03012010]
No part of this document may be copied or reproduced in any form by any means without prior written
consent of CONTEC CO., LTD.
Difference point with DTP-64(PC)
This product is a successor of the previous model DTP-64(PC). So you can use the same operating
procedures as DTP-64(PC).
The differences on the specification are as follows :
DTP-64A
DTP-64(PC)
Terminal type
SMKDSP1.5/24-5.08 [mfd. by
PHOENIX CONTACT]
equivalent
MK8/4
[mfd. by NIHON WEIDMULLER]
equivalent
Screws M3 M2.5
Terminal color Green Orange
Height of rubber
foot
7.2mm
5.0mm
Cautions
(1) No part of this document may be copied or reproduced in any form by any means without prior
written consent of CONTEC CO., LTD.
(2) The specifications of this product are subject to change without notice for quality improvement.
Even when using the product continuously, be sure to read the manual and understand the contents.
(3) All relevant issues have been considered in the preparation of this document. Should you notice
an omission or any questionable item in this document, please feel free to notify CONTEC CO.,
LTD.
(4) Regardless of the foregoing statement, CONTEC assumes no responsibility for any errors that may
appear in this document or
for any results of using the product.
(5) Brand and product names are trademarks of their respective holder.
(6) The foreign body (the metal piece, the combustible, and liquid, etc.) must not touch the product.
Otherwise, the product may malfunction, overheat or cause a failure.
-
1
-
2
-
3
-
4
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Contec DTP-4A Owner's manual
-
-
-
-
-
-
-
-
-
Other documents
-
Logik LTVST17 User manual
-
Crystorama ELS-7100-GA User manual
-
Ada Home Decor RUUB4051 User guide
-
Sandstrom SFMS14 Quick start guide
-
-
Protocol 5872-2T 3D Puzzle Super Tank User manual
-
-
-
Targus APTA29 Datasheet
-