ViaAqua Polar Bear Chiller CC-25B User manual

Brand
ViaAqua
Model
Polar Bear Chiller CC-25B
Type
User manual

ViaAqua Polar Bear Chiller CC-25B is designed for fresh or saltwater environments and features a compact, efficient design for maximum cooling efficiency. Its titanium heat exchanger resists corrosion, while the digital thermostat offers easy programming and accurate temperature control. Suitable for aquariums up to 75 gallons, this chiller operates quietly with a rotary compressor and provides thermal protection for added safety.

ViaAqua Polar Bear Chiller CC-25B is designed for fresh or saltwater environments and features a compact, efficient design for maximum cooling efficiency. Its titanium heat exchanger resists corrosion, while the digital thermostat offers easy programming and accurate temperature control. Suitable for aquariums up to 75 gallons, this chiller operates quietly with a rotary compressor and provides thermal protection for added safety.

Model: CC-25B and CC-50
• Titaniumheatexchanger
• Easytoprogramdigitalthermostat
• Compactefcientdesign
• Maximumcoolingefciency
• Forfreshorsaltwaterenvironments
WARNING
Buyer/User assumes all responsability for safety and proper
use not in accordance with the directions and sately labels.
-2-
FEATURES
1. Compressorisarotarytypethatisenergyefficientandquiet.
2. RotarycompressoriscertifiedULandCElisted.
3. Theheatexchangerismanufacturedonlyofpuretitanium.Titaniumisnotcorrosive
andwillnotbreakdowninsaltwaterthusensuringasafeenvironmentforsaltwaterfish,
invertebrate,freshwaterfish,reeffishandseafoodaquariums.
4. Temperaturecontrollerusescomputertechnologythatmakesiteasytouse,accurate
andreliable.
5. TheR134arefrigerantmeetsallenvironmentalandinternationalguidelines.
6. Thermalprotectedcompressor.
PRECAUTION AND SAFEGUARD
WARNING
» This product may contain chemicals known to the State of California to cause cancer and/
or birth defects or other reproductive harm. Wash you hand after handling the product.
» It is your sole responsability to verify that the plug and receptacle are clean/free of
moisture and salt build up at all times. The receptacle must be free of water, salt, calcium,
and magnesium. Failure to do so may cause re and/or loss of life.
» Do not plug into an extension cord.
» A drip loop must be used when plug into any electrical devices. A drip loop is part of the
cord hanging below the receptacle.
» The national code requires all aquarium equipment to be plugged into a G.F.C.I. (Ground
Fault Circuit Interrupter) electrical outlet. If you do not have a G.F.C.I., have an electrician
install one prior to operating any aquarium components.
* Readandfollowallprecautions,safeguardsandinstructions.
* Thechillermustnotcomeincontactwithwater.
* Intendedforindooruseonly.
* Verifythechillersvoltageisthesameasthepowersupply.
* Verifythechillerisonthepropersizeaquarium.
* Placethechilleronalevelsurface.
* Donotplacethechillerinsideofacabinetoraquariumstand.
* Donotcoverthechiller.
* Keepchillerawayfromdirectsunlight.
* Iftheunitisplacednearawalltheremustbeadequateventilation.Thechillerneedsto
bepositionedaminimumof10”fromthewall.
* Aminimumof10”ofclearanceinthefrontandbackofthechillerand5”clearanceonthe
sidesisnecessaryforadequateventilation.
* Iftheunitistogetwetordrippedondonotreachfortheunitunplugrst.
* Priortomaintenanceonanyelectricalaquariumapplianceormaintenancetothe
aquarium,youmustdisconnectallelectricalaquariumdevices.
-3-
* Donotoperateifthecordisdamaged,ifyouunitismalfunctioningdonotoperate
* Anymodicationstothechiller,chillerscomponentsand/orcontrolboardvoidswarranty.
INSTRUCTIONS FOR INSTALLATION
Required Tools (notincluded):Hoseclampsandwatersource.
1. Placethechillerinawellventilatedlevelsurface.
2. Attachthebarbedcompressionfittingtothechillerintakeandoutput.
3. Attachflexibletubingtotheintakebarbonthechillerusingahoseclamptoensure
tightness.
4. Connecttowatersupplyorwaterpumptotheunit.Waterflowshouldbeamin.of100
GPHandnottoexceed400GPH.Itisrecommendedtopre-filterthewaterfirst.
5. Attachapieceofflexibletubingtotheoutputbarbofthechillerusingahoseclamp.
6. Verifythatthewaterreturningfromthechillerisnotincloseproximitytotheintakewater
source.
7. Securethereturnline.
8. Verifythattherearenotanykinksinthetubingsupplyingwatertothechillerorinthe
outputtubereturningwatertotheaquariumorsump.
9. Turnonwaterpumporwatersupply.
10. Checkallconnectionstoverifythattherearenotanyleaks.
Setting the Thermostat
1. PlugthechillerintoaG.F.C.I.outlet.
2. SwitchtheunitON.
3. TheLEDscreennowwillreadthetemperatureofthecurrentaquariumwater.
4. PresstheSETbutton.TheLEDscreenwillnowflashandthegreenledlightwillbelit.
5. AdjustthetemperatureusingtheUP/DOWNbuttons.OncetheLEDscreenreadsthe
correcttemperature,PresstheSETbuttonagain.ThegreenLEDlightwillthengoout.
6. Thereisa2-3minutesdelaypriortothechillerturningon.WhenthechillerisON,the
greenLEDlightwillbelit.
NOTE:
* Ifinstallingonapreexistingaquarium,lowerthetemperatureby1-2degreesperday.
* Iftheunitisturnedoff,itwilltakeaminimumof3min.tocomebackon.Itwilltakeup
to5min.forthecomputer/thermostattoadjusttotheaquariumtemperatureandtheset
temperaturepriortoturningon.
-4-
FREQUENTLY ASKED QUESTIONS
If“EL”isdisplayed,thenthechillerismalfunctioning.Unplugimmediately.
If“EH”isdisplayedwiththealarmsound,thenthereisanelectricalshort.Unplug
immediately.
Problem: LED lights do not come on
* Checktoseeifthechillerispluggedin.
* Unplugtheunitandverifythatthefuseisgood.Ifthefuseneedstobereplaced,replace
withthesamesizefuse.
Problem: The compressor continues to turn on/off
* Incorrectpowersupply
* Lowwaterows
Problem: The unit is not cooling or not cooling adequately
* Thechillerisnotplacedinanareawithadequateventilation.
* Theradiatorneedstobemaintained.Cleanofalldustanddebris.
* Thesettemperatureishigherthanthewatertemperature.
* Radiatorisblocked.
* Thewaterowistoslowortofast.(Min.100GPHandmax.400GPH).
* Thechilleristoosmallfortheaquarium.
* Thereisnotaminimumof10”clearancearoundthechillerforadequateventilation.
* Thechillerisinstalledinsideanaquariumstand.
Problem: Too much noise
* Thechillermustbeplacedonalevelsurface
* Thechillerisnotfreestanding.Removeanyitemthatmaybeindirectcontactwiththe
chillercausingexcessvibration.
Problem: “EL” or “EH” is displayed
* Ingeneral,theprimaryreasonfor“EL”or“EH”tobedisplayediswhenthetemperature
sensorhasmalfunctioned.Pleasereferstotheinstructionbelowforproperdirections.
MAINTENANCE
1. Itisrecommendedtocleantheradiatoronceamonth.Todothis,gentlyvacuumthe
radiatortoremovealldustanddebris.
2. Donothosedownorusewatertocleantheradiatororotherexternalcomponents.
3. Onceamonth,ushtheinternalheatexchangerwithcleanfreshwater.Donotuseany
soapordetergents.
4. Donotsubmergeinwater.Thechillermustbecompletelyfreeofallmoisture.
5. Onceamonth,cleanthepre-lterofthepumpsupplyingwatertothechiller.
-5-
REPLACING TEMPERATURE SENSOR
Ifyouhaveanyquestionsorconcernsaboutworkingonthechilleralwaysconsultacertied
electricianrst.Requiredtools:wirecuttersandPhillipsscrewdriver.
Replacing temperature sensor for CC-25B
1. Unplugthechiller.
2. Unplug/disconnectthewaterbeingsuppliedtothechiller.
3. Disconnecttubing.
4. Drainthewaterfromtheheatexchanger.
5. Removetheeightscrewsthatholdonthecoverofthechiller.
6. Removecover.Caution:Connectedtothecoveristhetemperaturecontroller.Remove
slowly.Then,disconnecttheconnectionbetweenthecover/controllerandthechiller.
7. Ontheheatexchangeriscompressionfittingholdingthesensor.Loosenthefittingand
slideoutthesensor.
8. Withapairofdykes,removetheziptiesholdingthesensorwire.
9. Disconnectthesensorfromthetemperaturecontroller.
10. Installnewsensor.UseTeflontapeonthecompressionnut.
11. Securesensorwirewithnewziptiescuttingoffexcess.
12. Reconnectthetemperaturecontroller.
13. Replacecoverandsecurewithscrews.
14. Reinstall.
Replacing temperature sensor for CC-50
1. Unplugchiller.
2. Unplug/disconnectthewatersuppliedtothechiller.
3. Disconnecttubing.
4. Drainthewaterfromtheheatexchanger.
5. Removecompressiontubingconnectors.
6. Removethesixscrewsthatsecurethebackcoverofthechiller.
7. Removebackcover.Caution:connectedtothefrontcoverofthechilleristhe
temperaturecontroller.Removeslowly.
8. Disconnectwirefromcontrollertochillerusingthewhitequickwiredisconnect.
9. Removethefourscrewsthatsecurethefrontcovertothechiller.
10. Cutziptiesaroundtheinsulationandwiresgoingtothecompressorandheat
exchanger.
-6-
11. Removetheblackplasticcoverforthetemperaturecontroller.Therearetwocircuit
boardsinstalledinthecover.
12. Remove1
st
boardbyremovingthefourscrewsthatsecuretheboard.
13. Thenremovethe2
nd
boardbyremovingthetwoscrewsthatsecuretheboard.
14. Loosenthecompressionfittingsecuringthesensorintheheatexchanger.
15. Followthesensorwiretothecircuitboardanddisconnect(Note:securebothsidesof
thewire,disconnectandremove).
16. Removethesensor.
17. Keepthecompressionnutthatconnectstotheheatexchangerinplace.
18. Slidethecompressionnutontothenewsenorifnotalreadyinstalled.
19. Now,reconnectthenewsensortoboard.
20. Securethesensorbackintotheheatexchanger.
21. Secureallwiringandinsulationwithzipties.
22. Replacecircuitboardsbackintotheblackplasticcoverintheordertheywhere
removed.
23. Replacecoversandsecurewithscrews.
24. Reinstallunit.
Product
Specications
CC-25b CC-50
Voltage 120volt 120volt
Frequency 60Hz 60Hz
Ratedcapacity 450watt 850watt
Current 2amp 3.5amp
Refrigerant R134a R134a
Refrigerantweight 120g 220g
Min.-Max.waterow 100-400GPH 100-400GPH
InletandOutlet 5/8-3/4in. 5/8-3/4in.
Aquariumsize upto75gallontank upto125gallontank
Dimensions 14.2x8.2x10.5in. 16x13.2x12in.
UPC#0069037 27709 13665
-7-
REPLACEMENT PARTS
1.CircuitBoardforCC-25B 2.SensorProbe 3.Hoseclamp
4.CircuitBoardCC-50 5.TubingAdaptor 6.Fuse(F12a)
LIMITED WARRANTY
CommodityAxisInc.warrantsthatViaAqua®Chillerisfreefromdefectsforaperiodofone
yearfromtheinitialdateofpurchaseshownintheoriginalcashregisterreceipt.Commodity
AxisInc.disclaimsallotherwarrantiesofmerchantabilityand/orfitnessforaparticular
purpose.Althoughthislimitedwarrantygivesyouspecificrights,youmayhaveotherrights
thatmayvaryfromstatetostate.ThisWarrantyisvoidifthefailureoftheViaAqua®Chiller
oranypart,sealantorcomponentthereofisdueto(i)misuse,(ii)tampering,(iii)negligence,
(iv)misapplication,(v)abuse,(vi)accidentand/or(vii)failuretoproperly(a)maintain,(b)
clean,(c)pre-filter,(d)reassemble,(e)cleanand/orusetheViaAqua®ChillerwithaGround
FaultCircuitInterrupter(GFCI).
CONSUMER REMEDIES
CommodityAxisInc.entireLiabilityandyoursoleexclusiveremedyareeitherrepairor
replacementoftheViaAqua®chilleronlyifyoureturnthedefectiveViaAqua®chiller
directlytoCommodityAxisInc.withtheoriginalreceiptinthisoriginalboxalongwith
$25.00forshippingandhandling.Donotsendthechillerbyinsuredmail.Thechillermay
besentbyUPSrequiringsignatureuponarrival.AnyreplacementViaAqua®chillerwill
bewarrantedforremainingoftheoriginalwarrantyperiod.Innoteventshallanyshipping
chargesbereimbursed.InnoeventwillCommodityAxis,Inc.beliableforanyconsequential
orincidentaldamagesincluding,butnotlimitedto,lossoflife,personalinjury,property
damage,damagedequipment,lostprofits,lostwages,lostsavings,lostincome,etc.
arisingoutoftheuseoftheViaAqua®chiller.Somestatesdonotallowforthelimitationor
exclusionofliabilityforincidentalorconsequentialdamages,sotheaboveexclusionmay
notapplytoyou.
For model CC-25B
For model CC-50
Name Date
Address
City State Zip Code
Country Home Phone
Cell Phone Email
Date of Purchase Seller (Retail Name)
Seller’s Location Phone
*Afx a copy of your original purchase receipt here.Please mail warranty card and proof of
purchase within 15 days of purchase to:
Commodity Axis® Inc., 300 South Lewis Rd. Unit J. Camarillo CA 93012
IMPORTANT: Please make a copy of this warranty card and retain it for your records. Warranty
policy is subject to change without notice.
REGISTRATION CARD
ONE (1) YEAR WARRANTY
Bringing Products to Life
300 South Lewis Rd. Unit J. Camarillo CA 93012
Fax: (888) 989 0878
www.ViaAquaOceanpure.com
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

ViaAqua Polar Bear Chiller CC-25B User manual

Brand
ViaAqua
Model
Polar Bear Chiller CC-25B
Type
User manual

ViaAqua Polar Bear Chiller CC-25B is designed for fresh or saltwater environments and features a compact, efficient design for maximum cooling efficiency. Its titanium heat exchanger resists corrosion, while the digital thermostat offers easy programming and accurate temperature control. Suitable for aquariums up to 75 gallons, this chiller operates quietly with a rotary compressor and provides thermal protection for added safety.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents