CURT 13051 Owner's manual

Type
Owner's manual

CURT 13051 is a weight-carrying and weight distribution hitch that can be used to tow trailers with a maximum weight of 5,000 lbs. when used as a weight-carrying hitch and 6,000 lbs. when used as a weight distribution hitch. The maximum tongue weight is 500 lbs. when used as a weight-carrying hitch and 600 lbs. when used as a weight distribution hitch. The hitch is made of steel and has a black powder coat finish. It is designed to be easy to install and does not require any drilling. The hitch comes with all necessary hardware, including spacers, hex bolts, and conical washers.

CURT 13051 is a weight-carrying and weight distribution hitch that can be used to tow trailers with a maximum weight of 5,000 lbs. when used as a weight-carrying hitch and 6,000 lbs. when used as a weight distribution hitch. The maximum tongue weight is 500 lbs. when used as a weight-carrying hitch and 600 lbs. when used as a weight distribution hitch. The hitch is made of steel and has a black powder coat finish. It is designed to be easy to install and does not require any drilling. The hitch comes with all necessary hardware, including spacers, hex bolts, and conical washers.

GROSS LOAD CAPACITY WHEN USED AS A WEIGHT CARRYING HITCH: LBS. TRAILER WEIGHT & LBS. TONGUE WEIGHT.
GROSS LOAD CAPACITY WHEN USED AS A WEIGHT DISTRIBUTION HITCH: LBS. TRAILER WEIGHT & LBS. TONGUE WEIGHT
***DO NOT EXCEED VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY.***
HITCH WEIGHT: LBS.
INSTALL TIME:
MINUTES
INSTALL NOTES:
INSTALLATION STEPS
PERIODICALLY CHECK THIS RECEIVER HITCH TO ENSURE THAT ALL FASTENERS
ARE TIGHT AND THAT ALL STRUCTURAL COMPONENTS ARE SOUND.
Curt Manufacturing Inc., warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser. If the product is found to be defective,
Curt Manufacturing Inc., may repair or replace the product, at their option, when the product is returned, prepaid, with proof of purchase. Alteration to, misuse of, or improper installation of
this product voids the warranty. Curt Manufacturing Inc.'s liability is limited to repair or replacement of products found to be defective, and specifically excludes liability for incidental or
consequential loss or damage.
5,000
500
38
30
6,000
600
5/21/2020
Parts List
DESCRIPTION
PART NUMBER
QTY
ITEM
.250 x 1.38 x 1.50" ROUND HOLE SPACERCM-SP2521
HHCS,M12x1.75,45,CL10.910-1045962
WASHER,S-CON,1/2,YZ30-0014963
FUEL FILLER HOSE
REPLACES EXISTING
M12 FASTENERS
SPACER USED ON
SOME MODELS
SKID SHIELD
EXISTING WELDNUTS
DRIVER SIDE
FRAME RAIL
1
BUMPER COVER
1) Remove tow hook if present. Remove the four rearmost M12 fasteners from the vehicle frame leaving the
skid shield in place.
2) Raise hitch into position and loosely reinstall the four M12 Fasteners that were removed in step 2.
3) Place spacers between the frame and hitch before installing the supplied M12 hex bolts and conical washers
as shown. Spacers are not required on vehicles equipped with skid shield supports. Remove the support
bolts to install hitch.
4) With spacers or support bars between hitch and frame Torque all Fasteners to 79 lb.-ft.
- NO DRILLING REQUIRED
13051 / 78139 / RRH13051 99-04 JEEP GRAND CHEROKEE
2
3
PASSENGER SIDE
FRAME RAIL
  • Page 1 1

CURT 13051 Owner's manual

Type
Owner's manual

CURT 13051 is a weight-carrying and weight distribution hitch that can be used to tow trailers with a maximum weight of 5,000 lbs. when used as a weight-carrying hitch and 6,000 lbs. when used as a weight distribution hitch. The maximum tongue weight is 500 lbs. when used as a weight-carrying hitch and 600 lbs. when used as a weight distribution hitch. The hitch is made of steel and has a black powder coat finish. It is designed to be easy to install and does not require any drilling. The hitch comes with all necessary hardware, including spacers, hex bolts, and conical washers.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI