1 2
MD0302KE130729
Digital timer
TF2
Thank you for purchasing HANYOUNG product.
Please check whether the product is the exactly same as you ordered.
Before using the product, please read this instruction manual carefully.
Please keep this manual where you can view at any time
•If there is a concern about a serious accident caused by a malfunction or abnormality of this product,
please install an external protection circuit and devise a scheme for preventing an accident.
• This product does not contain an electric switch or fuse, so the user needs to install a separate electric
switch or fuse externally. (Fuse rating: 250V 0.5A)
•
To prevent defection or malfunction of this product, apply a proper power voltage in accordance with the rating.
• To prevent electric shock or malfunction of product, do not supply the power until the wiring is completed.
• Since this product is not designed with explosion-protective structure, do not use it any place with
flammable or explosive gas.
•
Do not decompose, modify, revise or repair this product. This may be a cause of malfunction, electric shock or fire.
•
Reassemble this product while the power is OFF. Otherwise, it may be a cause of malfunction or electric shock.
• If you use the product with methods other than specified by the manufacturer, there may be bodily
injuries or property damages.
• There is a possibility of occurring electric shock so please use this product after installing it onto a panel
while it is operating.
Warning
•
The contents of this manual may be changed without prior notification.
•
Before using the product you purchased, make sure that it is exactly what you ordered.
•
Make sure that there is no damage or abnormality of the product during the delivery.
•
Please do not use it in case of the time setting is 0. It may be a cause of its malfunction.
•
Please turn the power off before changing the time setting. In case of changing the time setting while it is ON, please reset it.
•
Do not use this product at any place with occurring corrosive (especially noxious gas or ammonia) or flammable gas.
•
Do not use this product at any place with direct vibration or impact.
•
Do not use this product at any place with liquid, oil, medical substances, dust, salt or iron contents. (Use at Pollution level 1 or 2)
•
Do not polish this product with substances such as alcohol or benzene. (Use neutral detergent.)
•
Do not use this product at any place with a large inductive difficulty or occurring static electricity or magnetic noise.
•
Do not use this product at any place with possible thermal accumulation due to direct sunlight or heat radiation.
•
Install this product at place under 2,000m in altitude.
•
When the product gets wet, the inspection is essential because there is danger of an electric leakage or fire.
•
If there is excessive noise from the power supply, using insulating transformer and noise filter is recommended.
The noise filter must be attached to a panel which is already connected to a ground and the wire between the
filter output side and power supply terminal must be short as possible.
•
If twisting the power cables closely together then it is effective against noise.
•
Do not connect anything to the unused terminals.
•
After checking the polarity of terminal, connect wires at the correct position.
•
When this product is connected onto a panel, use a circuit breaker or switch approved with IEC947-1 or IEC947-3.
• Install a circuit breaker or switch at near place for convenient use.
• Write down on a label that if the circuit breaker or switch is operating then the power will be disconnected
since the circuit breaker or switch is installed.
• the continuous and safe use of this product, the periodical maintenance is recommended.
• Some parts of this product have limited life span, and others are changed by their usage.
• The warranty period for this product including parts is one year if this product is properly used.
• When the power is on, the preparation period of contact output is required. In case of using signals of
external interlock circuit or etc., use it with a delay relay.
Caution
28, Gilpa-ro 71beon-gil, Nam-gu, Incheon, Korea
TEL:(82-32)876-4697 FAX:(82-32)876-4696
http://www.hynux.net
HANYOUNGNUX CO.,LTD
HEAD OFFICE
JL.CEMPAKA BLOK F 16 NO.02 DELTA SILICON II INDUSTRIAL PARK
LIPPO CIKARANG CICAU, CIKARANG PUSAT BEKASI 17550 INDONESIA
TEL : 62-21-8911-8120~4 FAX : 62-21-8911-8126
PT. HANYOUNG ELECTRONIC INDONESIA
INDONESIA
FACTORY
INSTRUCTION MANUAL
Safety information
Before using the product, please read the safety information thoroughly and use it properly.Alerts declared in the manual
are classified to Danger, Warning and Caution by their criticality
DANGER
DANGER indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury
WARNING
WARNING indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury
CAUTION
CAUTION indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury
There is a danger of occurring electric shock in the input/output terminals so please never let your body or
conductive substance is touched.
Danger
Suffix code
Model Code Description
TF2-
3 A N
Digital Timer (DIN 48mm x 96mm)
Displayable digits
3
3 digits display
Power supply voltage A100 - 240 V a.c 50 - 60 Hz
Power backup memory function N
None
Specification
Model TF2
Power supply voltage
100 - 240 V a.c 50-60 Hz
Voltage fluctuation ±10 % of the power supply voltage
Power consumption Approx. 5 VA (220 V a.c 60 Hz)
Reset Power reset (500 ㎳ min), external reset and manual reset (20 ㎳ min)
Inhibit Stop measuring the time due to the external signal (20 ㎳ min)
Control
output
Relay Instant : 1 c, 250 V a.c 3 A (resistive load)
Transistor Instant : open collector, 30 V d.c 100 ㎃ max.
Repetition accuracy ±0.01 % of the set value, less than ±0.05 s (Case of POWER START)
±0.005 % of the set value, less than ±0.003 s(Case of RESET START)
Installation Method Mounting Panel Method
Operation type Up (10 decimal system)
Operation mode N mode
External Connection Method
Bolt fixing type
Input Signal Method Contact : (open of contact, input by short-circuit)
Non-Contact : (input ON/OFF of Open Collector Transistor)
Alphabet display height 11 ㎜, width 8.0 ㎜
Time range 0.1 ~ 99.9 sec / 1 ~ 999 sec (selection done by using the front deep switch)
Insulation resistance 100 ㏁ min(500 V d.c) electric conduction terminal - non recharging metal
Dielectric strength 2000 V a.c 50/60 ㎐ 1 minute (within different recharging part from each other)
terminal - non recharging metal
Noise immunity Square wave noise due to the noise simulator, ±2 ㎸ (between the operational
power terminal), ±500 V (between the input terminal)
Vibration resistance 10 - 55 ㎐, double amplitude 0.75 ㎜, for 2 hour each in 3 axis direction
Shock resistance 300 ㎨, 3 times each in 3 axes direction
Life expectancy
Mechanical : 10 million min, Electrical : 100 thousand min (250 V a.c 3A Resistive load)
Ambient temperature -10 ~ 50 ℃
Ambient humidity 35 ~ 85 % RH
Storage temperature -20 ~ 65 ℃
Weight Approx. 380 g
Name of each part
Dimension and panel cutout & Connection diagram
[Unit : mm]
▒ Dimension
▒ Panel cutout ▒ Connection diagram
Displaying the elapsed time LED
Time setting switch
Output display
0.1s/1s selecting switch
Set from 1 sec ~ 999 sec
Set from 0.1 s ~ 99.9 sec
Operation Chart
▒ Output action mode
Mode UP
N
Inhibit input
Reset
Amount of resetting
0
Output
/
