Installation & Instructions
Included Parts
Wireless Charging Puck
Phone Mounting Plate
USB-C Charging Cable
WARNING: Do not use magnetic mount near hard-drive based
devices such as an iPod Classic / Video. Use caution when using near
pacemakers and other medical devices.
Check local and state vehicle laws regarding mobile device mounting
and use. Do not mount any device on or near vehicle airbags.
WARNING: This product can expose you to chemicals
including DEHP, DINP and BPA, which are known to the State of
California to cause cancer and birth defects or other reproductive
harm.For more information go to www.p65wrnings.ca.gov
Phone Mounting Plate Installation
1. Wipe phone or case
surface with included wipe
before applying template.
2. Mag Flex Plate Installation tool
has guide lines, ABCDE and 123.
3. Point pull tab up and make sure Mob Armor Logo is
positioned the direction you want it positioned. Peel down center
tab to expose the adhesive center of Mag Flex Plate. Use letter
and number markers to find the center of your phone over your
wireless charging location.
Note: Mag Safe Cases and Phones will magnetically position center. Non Mag Safe
devices will require alignment template.
4. Hold down center of Mag Flex Plate with one hand and peel
down and back the sides of position template. Double check you
are centered and aligned than remove template. Press firmly with
both hands the Mag Flex plate to your phone or case. Lets
Adhesive cure for 10 minutes before use.
IMPORTANT!
IF YOU NEED WARRANTY SERVICE OR REPLACEMENT
PARTS, PLEASE REACH OUT TO US DIRECTLY!
DO NOT RETURN PRODUCT TO RETAILER!
(805) 214-1815
Using With MobNetic Mounts
1. Attach charger to
mount before plugging
in.
2. Connect USB-C Cable to
mount and adapter.
Compatible with MobNetic Maxx,MobNetic Pro 90, MobNetic Go,
MobNetic Stik, MobNetic STXX
3. Mount charger and MobNetic
mount to desired location.
WARNING:
It is possible for the Wireless Charger / Tran smitter to interfere with some wireless systems within a car. Specifically,
key fobs with immobilizers, keyless start systems or tire pressure monitors. It is recommen ded to test the location of
your transmitter before deciding on final placement. Most interfere nce issues will be minimized by considering the
considering the follow ing
placement guidelines:
Install transmitter a m inimum of 10 inches aw ay from the ignition lock, key fob docking station,or any location where
the key fob might be stored while driving. If the transmitter canno t be located a suffici ent distance away as described
above, please use the following
suggestions whenever possible:
- Insert the key fob into the docking slot whe never possible while ope rating the transmitter.
- Connect the transmitter to a 12-volt accessory port that is powe red only while the vehicle's ignition is in the "ACC"
or "ON" position.
- Place phone on transmitter after vehicle is started.
Size:8*8cm
FCC Caution: Any changes or modifications not expressly
approved by the party responsible for compliance could void
the user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired operation.
FCC RF exposure statement:
The equipment complies with FCC Radiation exposure limit
set forth for uncontrolled environment. This equipment should
be installed and operated with minimum distance 20cm
between the radiator and your body.
-
1
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Other documents
-
Chrysler Pacifica Hybrid Owner's manual
-
-
Dodge Charger Owner's manual
-
-
Chrysler 300 Owner's manual
-
Dodge Challenger Owner's manual
-
-
-
-