Water Creation F2-0012 Installation guide

Brand: Water Creation

Model: F2-0012

Category: Sanitary ware

Type: Installation guide

Water Creation F2-0012 is an elegantly designed lavatory faucet that combines style with functionality. Crafted from durable materials, it ensures longevity and reliable performance. With its single-handle design, this faucet offers precise water flow and temperature control, enhancing your daily bathroom routine. The F2-0012 features flexible hoses for easy installation and a spout that can be positioned to your desired angle, providing a customized water flow.

Electric Drill with #2 Drill Bit

1/8" Drill Bit Wall Anchor (2pcs)

Tape Measure Screw (2pcs)

Builder's Pencil

Level

3 4

MIRROR INSTALLATION GUIDE

Tools for Assembly (Not Included)

Supplies (Included in Package)

Drill 2 holes at the marked positions and

insert wall anchors and screws.

Flip the mirror over and measure the

distance between point and point .

Use a level to mark the measured distance

between Point and Point on the wall.

Hang the mirror on the wall.

Thank you for choosing Water Creation. Your safety is our top priority, and we hope these

instructions help you use our products safely and effectively.

MODEL: F2-0012

BEFORE YOU BEGIN

1) Shut off water supply.

2) Carefully inspect waste and supply tubing for signs of damage.

3) Replace waste or supply tubing if necessary

B) HANDLE VALVE INSTALLATION

1) Connect the longer flex hose to valve body.

2) Place lower plastic washer and lock nut over valve body.

3) Insert valve body from under the sink.

4) Place upper rubber washers and escutcheon on valve spindle

5) Adjust position of valve body and secure with lock nut and escutcheon.

6) Place handle on spindle and tighten with screw.

TOOLS AND MATERIALS

LAVATORY FAUCET INSTALLATION GUIDE

Basin Wrench Adjustable wrench Teflon Tape

Pipe Wrench Screwdriver Flexible Water

Supply Line

A) SPOUT INSTALLATION

1) Remove lock nut and connect tee.

2) Apply plumbers’ putty or sealant.

3) Locate mounting hole and insert spout into deck or lavatory.

4) Screw and tighten washers, lock nut onto the shank and secure the spout.

5) Screw and tighten the connect tee to the shank.

6) Remove excessive plumbers’ putty or sealant.

***Half turn loosen the tee for ideal position to connect with hoses***

METAL WASHER

RUBBER WASHER

LOCK NUT

CONNECT TEE

RUBBER WASHER

PLASTIC WASHER

LOCK NUT

MODEL: F2-0012

COMPLETE INSTALLATION

C) FLEXIBLE HOSE INSTALLATION

1) Connect flexible hoses to supply tee.

2) Secure hoses with wrench. Do not over tighten.

3) Circle the excessive part of hoses as shown in figure below.

D) DRAIN WASTE INSTALLATION

1) Disassemble the drain.

2) Apply plumbers’ putty or sealant to bottom side of flange.

(Or use attached rubber washer to instead of putty)

3) Insert drain body through sink.

4) Attach the gasket, Teflon washer and tighten the lock nut.

5) Apply Teflon tape to the drain pipe threads and screw with drain body

6) Remove excessive plumbers’ putty or sealant.

E) SUPPLY CONNECTION

1) Install lavatory according to manufacturer’s instructions.

2) Connect hoses (not provided) to angle stops.

3) Tighten all connections.

*** VERY IMPORTANT ***

4) Flush out water for two minutes before connect hose to faucet valve.

(This act to avoid debris trapped the flow regulator)

F) INSTALLATION CHECKOUT

1) Ensure all connections are tightened properly.

2) Turn on main water supply.

3) Turn on and off cold and hot water respectively.

4) Turn on both hot and cold water and turn off. Check for leaks.

5) Remove the aerator cap and aerator. Check for debris. Clean of necessary.

6) Reinstall aerator.

Water Creation F2-0012 Installation guide

Brand: Water Creation

Model: F2-0012

Category: Sanitary ware

Type: Installation guide

Download PDF

report

Water Creation F2-0012 Installation guide

Water Creation F2-0012 Installation guide

Related papers

Other documents