Livex 47166 User manual

Brand
Livex
Model
47166
Type
User manual

This manual is also suitable for

Livex 47166 is a lighting fixture designed to provide ambient lighting in various indoor settings. It features a unique design with multiple pipes and a ball joint, allowing for flexible positioning of the light source. Installation requires basic electrical knowledge and involves connecting wires and securing the fixture to a junction box. The fixture accommodates multiple light bulbs, but users should ensure they do not exceed the specified wattage to prevent overheating.

Livex 47166 is a lighting fixture designed to provide ambient lighting in various indoor settings. It features a unique design with multiple pipes and a ball joint, allowing for flexible positioning of the light source. Installation requires basic electrical knowledge and involves connecting wires and securing the fixture to a junction box. The fixture accommodates multiple light bulbs, but users should ensure they do not exceed the specified wattage to prevent overheating.

ASSEMBLING & INSTALLATION INSTRUCTIONS
The drawing shown may not exactly match the product enclosed.
However, the installation instructions do apply to this product.
47166 47168
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.
ATTENTION! COUPER LE COURANT AU FUSIBLE OU UN DISJONCTEUR.
ASSEMBLING THE FIXTURE (Fig.1)
1. Shut off the power at the circuit breaker box. Remove old fixture and all
hardware from Junction Box.
2. Carefully unpack your new fixture and lay out all the parts on a clear area.
Take care not to lose any small parts necessary for installation.
3. While holding the end coupling sleeve of pipes(J) onto the screwed
connection of big ring(K), the other end pipe thread insert to the bottom hole of
ball, lock it securely with the cone nut(I), use the same method install other
pipes. Slide the pipe thread(H) insert to the hex coupling in the ball and lock it
with the end hex nut. Slide the cover(G) onto the ball and lock it with the
column nut(F).
4. Slide the electrical wires through the tubes(E)/(D)/(C) and canopy (A).
5. Raise the tube (E) to top pipe screw of lamp body, raise the tube (C)/(D) and
canopy (A) to the pipe screw in order, then by turning it clockwise until tight.
6. Install the light bulbs (Not included) in accordance with the fixture
specifications. NOTE: DO NOT EXCEED THE SPECIFIED WATTAGE!
7. Thread the two mounting screws into the pre-drilled holes in the Mounting
plate spaced the same distance apart as the holes in the canopy. Attach the
Mounting plate to the Junction Box with the two Junction Box screws as
shown. The side of the Mounting plate marked "GND" must face to out. The
junction box is not included.
8. While holding the assembly lamp towards the ceiling, connect the electrical
wires as Shown in Fig.2, making sure that all wire nuts are secured. You may
have to wrap the connections with electrical tape. If your outlet has a ground
wire (green or bare copper), connect the fixture ground wire to it. Otherwise
connect fixture’s ground wire directly to the Mounting plate with the green
screw provided. After wires are connected, tuck them carefully inside the
Junction Box.
9. Raise the canopy (A) on to the Junction box, aligning screws on mounting
plate with mounting holes in canopy and lock it securely with the ball nuts (B).
Your installation is now complete. Return power to the junction
box and test the fixture.
FIG.1
FIXTURE
WIRES
Black or
Smooth
HOUSE
WIRES
Black(Hot)
FIXTURE
WIRES
White or
Ribbed
FIXTURE
WIRES
Bare
Copper
(Ground)
HOUSE
WIRES
White
(Neutral)
HOUSE
WIRES
Green or Bare
Copper(Ground)
Thank you for purchasing a LIVEX product.
Need assistance with parts or assembly? Please call customer service at: 800-761-8056
Or visit us online at: WWW.LIVEXLIGHTING.COM
©COPYRIGHT ALL RIGHTS RESERVED.LIVEX LIGHTING,INC. DOC20210347166
FIG.2
  • Page 1 1

Livex 47166 User manual

Brand
Livex
Model
47166
Type
User manual
This manual is also suitable for

Livex 47166 is a lighting fixture designed to provide ambient lighting in various indoor settings. It features a unique design with multiple pipes and a ball joint, allowing for flexible positioning of the light source. Installation requires basic electrical knowledge and involves connecting wires and securing the fixture to a junction box. The fixture accommodates multiple light bulbs, but users should ensure they do not exceed the specified wattage to prevent overheating.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents