Legrand UTP-FIBER1G-USB User guide

Legrand
Brand
Legrand
Model
UTP-FIBER1G-USB
Category
Network media converters
Type
User guide

Legrand UTP-FIBER1G-USB is a 1G Fiber Converter with Power over USB that supports single-mode and multi-mode fiber connections. It offers distances up to 10km for single-mode fiber and up to 800m for multi-mode fiber. With Link Fault Pass-Through (LFP) support, it ensures a reliable connection by propagating link status information between devices. It features individual LEDs for power and communication status, and auto crossing for simplified cabling. Additionally, the auto dust cover protects the fiber port when not in use.

Legrand UTP-FIBER1G-USB is a 1G Fiber Converter with Power over USB that supports single-mode and multi-mode fiber connections. It offers distances up to 10km for single-mode fiber and up to 800m for multi-mode fiber. With Link Fault Pass-Through (LFP) support, it ensures a reliable connection by propagating link status information between devices. It features individual LEDs for power and communication status, and auto crossing for simplified cabling. Additionally, the auto dust cover protects the fiber port when not in use.

UTP-Fiber1G-USB QSG 1
UTP_Fiber1G_USB-QSG-revA1 255-80-0069-00-RoHS
UTP-to-Fiber Media Converter
Thank you for purchasing the UTP-Fiber1G-USB, a 1G Fiber Converter with Power over USB.
Package Contents
• 1G Fiber-to-UTP Converter with Power over USB
QS Rule
Product Features
• Single-mode and multi-mode fiber support
• Distance up to 10km for single-mode fiber and up to 800m for multi-mode fiber
• Link Fault Pass-Through (LFP) support
• Auto dust cover
• Auto crossing to simplify cabling (MDI/MDIX)
• Individual LEDs to indicate power and communication status
QS Rule
LED Panel
LED Label
Color
Status
Meaning
Power
Green
On
Module On
No light
Off
Module Off
Link/ACT
Green
On
1000 Mbps
Green Blinking
On
Activity
No light
Off
Disconnected
Fiber
Blue
On
Connected
No light
Off
Disconnected
QS Rule
QUICK SETUP GUIDE
UTP-Fiber1G-USB QSG 2
UTP_Fiber1G_USB-QSG-revA1 255-80-0069-00-RoHS
LED Operation for Link Fault Pass-Through (LFP)
Diagram
Conditions
Description
Color
Status
Normal Operations
PWR
Green
On
Link/ACT
Green
On
Fiber
Blue
On
Switch and Converter
disconnected
PWR
Green
On
Link/ACT
Green
Off
Fiber
Blue
Off
Converter TX Fiber
disconnected *
PWR
Green
On
Link/ACT
Green
Blinking every 5 seconds
Fiber
Blue
Off
Converter RX Fiber
disconnected *
PWR
Green
On
Link/ACT
Green
Off
Fiber
Blue
Off
*Note: The device at the remote side must support Link Fault Pass-Through (LFP).
QS Rule
Installing the UTP-Fiber1G-USB
1. Plug the RJ45 connector of UTP-Fiber1G-USB into the RJ45 port of the target device.
2. Plug the USB type A connector of UTP-Fiber1G-USB into the USB port of the target device to serve as power source.
UTP-Fiber1G-USB QSG 3
UTP_Fiber1G_USB-QSG-revA1 255-80-0069-00-RoHS
3. Flip open the dust cover of the UTP-Fiber1G-USB to reveal the fiber port, then connect the fiber cable’s LC connector to the fiber port.
Warning: To prevent damage to the dust cover, do not bend it all the way back.
4. Connect the other end of the fiber cable to the fiber port of a target device to verify that the fiber connection is complete.
QS Rule
Removing the UTP-Fiber1G-USB
1. Press the fiber cable’s connector and pull to remove it from UTP-Fiber1G-USB.
2. Remove the UTP-Fiber1G-USB's USB type A connector from its power source.
3. Press the latch down and pull to remove UTP-Fiber1G-USB from the target device's RJ45 port.
QS Rule
UTP-Fiber1G-USB QSG 4
UTP_Fiber1G_USB-QSG-revA1 255-80-0069-00-RoHS
Product Specifications
General Specifications
Function
Fiber Converter dongle
RJ45 port
1000 Base-Tx Auto negotiation (IEEE 802.3u)
Fiber Port
1000 Base-X Full-duplex (IEEE 802.3u)
Properties of optic port
Total number of FO ports
1
Connector type
LC
Fiber Mode
Duplex Fiber
Link Distance (Max)
Up to 10Km for Single-mode fiber
Up to 800m for Multi-mode fiber
Data rate
1.25Gbps
Wavelength
1310nm
Optical Output Power Range
-1 ~ -5 dBm
Optical Receive Sensitivity
-21 ~ -3 dBm
Properties of RJ45 port
Total number of RJ45 Ethernet interfaces
1
Connection type
RJ45 male
Data rate
1000Mbps
MDI/MDIx switchover
Auto MDI/MDIX
Environmental Specifications
Operating temperature
0℃~55℃
Operating Humidity (Max)
5%~95%
Degree of protection
IP20
Power Requirements
Connector type
USB 3.0 / USB 2.0 Type A
Power Consumption
typical
2.1 W
maximum
2.5 W
UTP-Fiber1G-USB QSG 5
UTP_Fiber1G_USB-QSG-revA1 255-80-0069-00-RoHS
Physical Characteristics
Housing
Metal
Dimension
82.33(L)*20(W)*16.56(H) mm
Weight
50g
Standards and Certifications
EMC/EMI
Green product
RoHS and REACH
CE and FCC
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

Legrand UTP-FIBER1G-USB User guide

Legrand
Brand
Legrand
Model
UTP-FIBER1G-USB
Category
Network media converters
Type
User guide

Legrand UTP-FIBER1G-USB is a 1G Fiber Converter with Power over USB that supports single-mode and multi-mode fiber connections. It offers distances up to 10km for single-mode fiber and up to 800m for multi-mode fiber. With Link Fault Pass-Through (LFP) support, it ensures a reliable connection by propagating link status information between devices. It features individual LEDs for power and communication status, and auto crossing for simplified cabling. Additionally, the auto dust cover protects the fiber port when not in use.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents