T.B. 06/2005
Typ C40 / 110
EN
English
ABSORPTION REFRIGERATOR + OVEN for CARAVAN AND MOTORHOME
RMT 7650
RMT 7850
RMT 7651
RMT 7851
RMT 7655
RMT 7855
Model number .............................................
Product number
.............................................
Serial number .............................................
Please state for future reference :
MANUAL
INSTALLATION INSTRUCTIONS
2
Dansk
Deutsch
Ελληνικά
English
Español
Français
Italiano
Nederlands
Norsk
Português
Suomi
Svensk
via INTERNET www.dometic.com
Kundeservice
Kundendienst
Εξυπηρέτηση Πελατών
Customer Service
Servicio de Atención al Cliente
Service après-vente
Servizio Clienti
Klantenservice
Kundeservice
Serviço de Atendimento a Clientes
Asiakaspalvelu
Kundservice
Instructions for storing food in a refrigerator:
No refrigerator of any kind can improve the quality of the food; refrigerators can only maintain the food's quality for a short
duration as from the time of storing it.
Please observe the following particular conditions for storing food in a refrigerator that is built into a vehicle:
- A change in the climatic conditions such as temperature fluctuations
- High temperatures inside the vehicle when it is closed and parked in direct sunlight (temperatures are possible
up to 50°C)
- Use of the refrigerator whilst travelling with the power supply of 12V--DC
- A refrigerator built in behind a window and exposed to direct sunlight
- Storing the goods too soon, i.e. shortly after switching the device on for use
Under these particular conditions the refrigerator cannot guarantee having the temperature needed for food that perishes quik-
kly.
Foods that perish quickly include: all the products with a stipulated use-by date and a minimum storage temperature of +4°C
or less, especially for meat, poultry, fish, sausage, pre-packed foods.
Instructions
- Pack raw and cooked foods separately (e.g. in containers, aluminium foil, etc.)
- Only remove the outside packaging of single packs if all the necessary data, such as the use-by date, for
example, can also be read on the single packs.
- Do not leave cooled goods outside the refrigerator for too long.
- Place the foods with the next use-by date at the front, accordingly.
- Pack away any left-over food again and eat at the first opportunity.
- Wash your hands before and after touching any food.
- Clean the inside of the refrigerator at regular intervals.
Information :
Please observe the instructions and information regarding the use-by date on the outside packaging of the food.
Please observe the following sections in these instructions: "5.1 Cleaning" and "5.3 Storing food".
Safety instructions
These operating instructions should be kept in a safe place.
If this device is passed on, please include these operating instructions with it.
© Dometic GmbH - 2005 - Subject to change without notice - Printed in Germany
3
1.0 INTRODUCTION ................................................ 4
2.0 FOR YOUR SAFETY ......................................... 4
2.1 Warning and safety notices .................................. 4
2.2 Coolant .................................................................... 5
3.0 WARRANTY AND CUSTOMER SERVICE ........ 5
3.1 Damages in transit ................................................. 5
4.0 DESCRIPTION OF MODEL ............................... 6
4.1 Controls ................................................................... 6
5.0 REFRIGERATOR GUIDE ................................... 7
5.1 Cleaning .................................................................. 7
5.2 Using the refrigerator ............................................ 7
5.3 Storing food ............................................................ 12
5.4 Making ice cubes ................................................... 13
5.5 Defrosting ............................................................... 13
5.6 Positioning the storage racks ............................... 13
5.7 Door locking ........................................................... 14
5.8 Switching off the refrigerator ............................... 14
5.9 Winter operation ..................................................... 14
5.10 Interior light ............................................................ 15
5.11 Changing the decor panel ..................................... 15
5.12 Changing the doorhang ......................................... 16
5.13 Troubleshooting ..................................................... 17
6.0 INSTRUCTION FOR OVEN ............................... 18
6.1 Operation of oven .................................................. 18
6.2 Cleaning .................................................................. 18
6.3 Switching on the oven ........................................... 19
6.4 Winter operation ..................................................... 19
7.0 GENERAL REMARKS ....................................... 20
7.1 Technical data ......................................................... 20
7.2 Declaration of conformity ...................................... 20
7.3 Maintenance ........................................................... 21
7.4 Product liability ...................................................... 21
7.5 Environmental hints ............................................... 21
7.6 Disposal .................................................................. 21
7.7 Energy-saving tips ................................................. 21
8.0 INSTALLATION GUIDE ..................................... 22
8.1 Installation ............................................................... 22
8.2 Draught-free installation ........................................ 23
8.3 Ventilation and air extraction ................................ 25
8.4 Installation of the ventilation system ................... 26
8.5 Installation recess .................................................. 27
8.6 Securing the refrigerator ....................................... 27
8.7 Connections gas/electrical installation ................ 28
8.8 Gas installation ....................................................... 28
8.9 Electrical installation ............................................. 30
TABLE OOF CCONTENTS
Warning
Attention
Information
Environmental
Advice
4
INTRODUCTION
You have made an excellent choice in selecting the Combined Absorption
Refrigerator and Gas Baking Oven from Dometic.
We are sure that you will be fully satisfied with your new appliance in all respects.
The appliance, which works silently, meets high quality standards and guarantees
the efficient utilisation of resources and energy throughout its entire life cycle, during
manufacture, in use and when being disposed of.
Before you start to use the appliance, please read the installation and operating
instructions carefully.
The refrigerator is designed for installation in leisure vehicles such as caravans or
motorcaravans. The appliance has been certified for this application in accordance with
EU Gas Directive 90/396/EEC.
FOR YOUR SAFETY
Warning and safety notices
Never use a naked flame to check the appliance for leaks.
Protect children!
When disposing of the refrigerator, remove all refrigerator doors and leave the
storage rack in the refrigerator. This will prevent accidental locking in or suffocation.
If you smell gas:
- close the locking tap of the gas supply and the valve on the cylinder.
- open the windows and leave the room.
- do not switch on anything electrical.
- extinguish naked flames.
Never open the cooling unit; it is under high pressure.
Work on the gas, flue system and electrical components must only be
carried out by qualified service personnel.
It is imperative that the operating pressure should correspond to the data given on
the model plate of the appliance.
Compare the operating pressure data given on the model plate with the data on the
pressure monitor of the liquid gas cylinder.
Gas operation of the appliance is not permitted while travelling on ferries.
Covers ensure electrical safety and must only be removed using a tool.
The appliance must not be exposed to rain.
The refrigerator is not suitable for the proper storage of medications.
When in operation, the temperature in the oven reaches very high levels.
When handling hot objects, always use protective gloves.
The oven is under no circumstances to be used as a heating unit.
1.0
2.0
2.1
Warning Attention
Coolant
Ammonia is used as a coolant.
This is a natural compound also used in household cleaning agents (1 litre of
Salmiak cleaner contains up to 200g of ammonia - about twice as much as is used
in the refrigerator). Sodium chromate is used for corrosion protection (1.8% of the
solvent).
In the event of leakage (easily identifiable from the unpleasant odour):
Switch off the appliance.
Air the room thoroughly.
Inform the authorised Customer Service department.
WARRANTY AND CUSTOMER SERVICE
Warranty arrangements are in accordance with EC Directive 44/1999/CE and the
normal conditions applicable for the country concerned. For warranty or other
servicing, please contact our Dometic Service department. Any damage due to impro-
per use is not covered by the warranty. The warranty does not cover any modifica-
tions to the appliance or the use of non-original Dometic parts;
the warranty does not apply if the installation and operating instructions are not
adhered to and no liability shall be entertained. Parts can be ordered throughout
Europe from our Dometic Service department. Your Service Centre contact numbers
numbers are found in the “European Service Network” booklet
When contacting Dometic Service, please state the model, product number and
serial number together with the MLC Code, if applicable. You will find this information
on the data plate inside the refrigerator.
Damages in transport
Please check, immediately upon removing the packaging, whether refrigerator and oven
have been in any way damaged during transit.
Any damage sustained in transit must be reported to the transportation company
concerned no later than seven days after delivery of the goods.
5
2.2
3.0
3.1
6
DESCRIPTION OF MODEL
Controls
4.0
4.1
RMT 7651 L
e.g.
“RM” Refrigerator Mobil /
Mobile Absorber Refrigerator
“T” Refrigerator combined with baking oven
“L” with interior light
“5” curved door
“0” manual energy selection and manual
ignition “Piezo”
“1” manual energy selection
“5” automatic and manual energy selection
Manual energy selection / manual ignition “Piezo” (RMT 7X50)
Automatic and manual energy selection
/ automatic ignition
AES (RMT 7X55)
A = switch on and energy selection (Refrigerator) D = switch for frame heating
B = gas/electric thermostat AC/DC (Refrigerator) E = operating display frame heating
C = manual ignition button “Piezo ignition/battery igniter” G = Galvanometer (Refrigerator)
(Refrigerator) J = switch on / thermostat (Oven)
A = switch on and energy selection (Refrigerator)
B = gas/electric thermostat AC/DC (Refrigerator)
C = operating displays 4 LEDs
(Refrigerator)
D = switch for frame heating
E = operating display frame heating
F = temperature setting display
H = dimmer for LED-displays
(only accessable when door opens)
J = switch on / thermostat (Oven)
A
B
C
E
B
F
A
H
D
G
E
Manual energy selection / automatic ignition MES (RMT 7X51)
A = switch on and energy selection (Refrigerator) D = switch for frame heating
B = gas/electric thermostat AC/DC (Refrigerator) E = operating display frame heating
C = operating displays 3 LEDs
(Refrigerator) J = switch on / thermostat (Oven)
A
B
C
D
E
C
J
J
J
D
7
REFRIGERATOR GUIDE
Cleaning
Before switching the refrigerator on to use it, we recommend that you clean it inside
and out, and repeat this at regular intervals.
Use a soft cloth and lukewarm water with a mild detergent.
Then rinse the appliance with clean water and dry thoroughly.
Remove dust from the refrigerator unit at yearly intervals using a brush or soft cloth.
(accessable through upper vent grille).
ATTENTION
To avoid deterioration of materials:
Do not use soap or hard, abrasive or soda-based cleaning agents.
Do not allow the door seal to come into contact with oil or grease.
Using the refrigerator
The cooling unit is silent in operation.
When the appliance is first put into operation, there may be a mild odour
which will disappear after a few hours.
Ensure the living area is well ventilated.
The refrigerator will take several hours to reach its operating temperature
in the cooling compartment.
The freezer compartment should be cold about one hour after switching on
the refrigerator.
5.2
5.0
5.1
AC mains power
12V DC
Gas
OFF
Automatic energy selection
(AES-models only)
OFF
AC mains power
12V DC
Gas
The refrigerator is equipped to operate on mains power, DC or liquid gas (propane/
butane). The desired power option is selected by means of energy selector switch (A).
Energy selector switch (A) has the following settings: AC mains power, DC (12V),
Gas (liquid gas), OFF.
Appliances with automatic energy selection have the additional setting “AUTO” .
RMT 7650 / RMT 7850
RMT 7651 / RMT 7655 / RMT 7851 / RMT 7855
8
Electrical operation
1. 12V - operation (DC)
The refrigerator should only be used while the motor is running,
otherwise the on-board-battery would be discharged within a few hours!
2. Mains power
This option should only be selected where the supply voltage of the connection for
power supply corresponds to the value specified on the data plate. Any difference in
values may result in damage the appliance.
2. Use rotary switch “B” to regulate the
temperature in the main refrigerator
compartment.
A
1. Set energy selector switch “A” to 12V.
Operating display “C”, 12V lights “green”.
Appliance is in function.
1. Set energy selector switch
“A” to 12V.
The refrigerator operates without
thermostatic control.
(continuous operation)
2. Use rotary switch “B” to regulate the
temperature in the main refrigerator
compartment.
A
1. Set energy selector switch “A” to “230V”.
Operating display “C”, 230V lights “green”.
Appliance is in function.
1. Set energy selector switch
“A” to “230V”.
C
C
If the operating display fails to light up (it
lights up “red” at AES models) the device is
not in operation.
B
B
5.2.1
A
If the operating display fails to light up (it lights up “red” at AES models)
the device is not in operation. (For troubleshooting see 5.13).
A
RMT 7651 / RMT 7655 / RMT 7851 / RMT 7855RMT 7650 / RMT 7850
RMT 7651 / RMT 7655 / RMT 7851 / RMT 7855RMT 7650 / RMT 7850
9
Gas operation
The refrigerator should only be operated using liquid gas
(propane, butane). Do not use town gas or natural gas.
If the refrigerator is operated during travel using gas, the precautions
stipulated by the legislation in the respective country must be taken (in
conformity with the European standard EN 732).
Operating the refrigerator with gas is not permitted during travel in
France and Australia.
As a basic rule, operation using gas is prohibited in petrol stations.
1. Open the valve of the gas cylinder.
2. Open the shut-off valve to the gas supply.
The ignition process is activated automatically, accompanied by a ticking sound
approx. 30 sec. Upon successful ignition, the display LED “C” “Gas” lights yellow.
The refrigerator is in function. Use rotary switch “B” to regulate the temperature in the
main refrigerator compartment.
- Repeat the entire process if the flame has gone out.
- Use rotary switch (B) to regulate the temperature in the main refrigerator compart-
ment.
All refrigerators, whether manual or automatic ignition, are equipped with
automatic flame protection, which automatically cuts off the supply of gas
approximately 30 seconds after the flame goes out.
When using for the first time, and after changing the gas cylinder, the gas
pipes may contain air. By means of brief operation of the refrigerator and
any other gas appliances (e.g. cookers), air is removed from the gas
pipes. The gas will then ignite without delay.
A
3. Set energy selector switch “A” to gas.
4. Set rotary switch “B” to “MAX” postion.
C
5.2.2
RMT 7650
RMT 7651 / RMT 7655
3. Set energy selector
switch “A” to gas.
4. Press and hold
rotary switch “B”.
5. Activate ignition
by pressing the
button (C) and
keep it depressed.
A
B
C
6. Once the flame has been ignited
and is burning, the needle of the
galvanometer passes over into the
green section.
“AUTO”-operation ( AES only )
RM7XX5 L - models are equipped with an “AUTO”-MATIC function.
Explanations:
Upon switching on, the electronics automatically select one of the three
possible energy types: 230V - 12V - liquid gas. The control electronics
automatically ensure that the refrigerator is supplied with the optimum
source of energy in each respective case.
Priority: 1.) Solar (12V DC)
2.) 230V AC
3.) 12V DC
4.) Liquid gas
The selected energy is displayed by the corresponding LED (i.e. 230V)
.
230 V - operation
If sufficient supply voltage is available (more than 200V), this power source is
selected as the first option ( no solar-system installed).
12 V - operation
12V operation should only be selected while the vehicle motor is running or there
is sufficient voltage available from the solar system. This can be detected from
the D+ connection of the alternator to the electronics, or from the respective
signal on the solar charge regulator.
Gas operation
Gas operation is selected in the following circumstances:
No supply voltage available.
The vehicle engine is not running.
Supply voltage less than 200V
REFUELLING STOP
In order to prevent unintended switching to gas operation during refuelling,
the electronic system starts gas operation of the refrigerator, after the
motor has been turned off for 15 mins. During this time the appliance is in
stand-by operation mode and only the "AUTO" LED lights up.
The use of naked flames is prohibited in petrol station environments.
If the refuelling stop lasts longer than 15 mins., the refrigerator should be
switched off at the main switch “A”, or switched over to another energy
type.
10
5.2.3
1. Set energy selection switch “A” to position
“AUTO”.
The LED “AUTO” lights “green”.
Manual operation is possible at any time.
11
If gas faults occur the operating LED “C”
flashes
yellow.
Remedies:
Set the energy selector switch “A” to position “OFF”.
1. Is there any gas in the gas bottle?
2. Is the gas bottle valve open?
3. Is the on-board shut-off valve open?
If point 1 to 3 is ok proceed with point 4 .
4. Set the energy selector switch “A” to position “AUTO” again.
The ignition starts once more.
If after about 30 seconds the operating display (C) starts flashing
yellow
again, the gas fault has not been cleared (e.g. air in the gas pipe).
5. Briefly set the energy selector switch “A” to position “OFF” and back again to
position “AUTO”!
To remove air from the gas pipes, repeat this procedure 3-4 times.
If these actions do not help, please call an authorised Dometic Service
Centre.
Frame heating
Additional functions (RMT 7655, RMT 7855)
5.2.4
C
A
Gas faults (MES and AES)
Temperature setting display (D) with 4 LED to
indicate the selected temperature (MIN - MAX).
LED - dimmer (E) for adjusting the brightness of
the display-LED.
(only accessible when door opens)
D
E
Underneath the fascia is a knurled knob for
adjusting the brightness (see item E above).
All models are equipped with a frame heating
(12VDC/3,5W) around the freezer compartment. During
summer months with high temperatures and humidity the
metal frame may have water droplets forming. To evapo-
rate these droplets switch on the frame heating with
switch (A). The LED (B) indicates that the heating is on.
The frame heating will draw 12V DC power continuously.
Observe LED (B) when the engine is shut off while parking the vehicle.
Shut off the frame heating.
A
B
5.2.5
5.2.6
12
Temperature setting cooling compartment
As shown, you are able to regulate the temperature of
the cooling compartment, if necessary, by turning
rotary knob (B).
Exchange of the igniter’s battery (RMT 7X50, refrigerator only)
Storing food
Switch the refrigerator on approx. 12 hours before filling it.
Always store pre-cooled foods in the refrigerator. Make sure that the food is well
cooled when it is bought and also when transporting it. Use insulated cooling bags.
When taking food out of the refrigerator only open the refrigerator door very briefly.
Foods must be packed - best of all in closed containers - and stored separately from
each other.
Allow foods that have been warmed up to cool down before storing.
Store quickly perishable foods directly next to the cooling fins.
Products that could emit volatile, flammable gases must not be stored in the
refrigerator
The refrigerator must not be exposed to direct sunlight. Please bear in mind that the
temperature inside a closed vehicle increases sharply if exposed to sunlight and that
this can reduce the efficiency of the refrigerator.
The air inside the refrigerator unit MUST be able to circulate freely without any
hindrance. (see also Section 8.3 "Ventilation and air extraction" in the Operating
Manual).
The freezer compartment is suitable for making ice cubes and for short-term
storage of frozen food. It is not suitable as a means of freezing foods.
5.2.7
B
TIP
medium setting
The cooling unit’s performance is influenced by ambient temperatures.
Please select the medium setting for ambient temperatures between
+15°C and +25°C. The unit operates within its optimum performance range.
5.3
Dometic refrigerators work according to the absorption principle.
Due to physical reasons, an absorption system responds slowly to changes
made on the thermostat controller, or a loss in cooling through opening the
door, or storing food. The devices fulfill the cooling performance require-
ments of the Climatic Class SN acc. to EN/ISO 7371 in the temperature range
of +10°C to 32°C ambient temperature.
Unlock the battery by depressing and turning the button (C) approx. 90° clockwise.
Remove cap and exchange battery (1.5V AAA / R3 / Micro). Observe correct polarity.
5.2.5
C
+
_
13
Making ice cubes
Ice cubes are best frozen overnight. At night, the refrigerator has less work to do and
the unit has more reserves.
Defrosting
As time goes by, frost builds up on the fins.
When the layer of frost is about 3mm thick, the refrigerator should be defrosted.
1. Switch off the refrigerator, as described in Section 5.8 - "Switching off".
2. Remove the ice cube tray and food.
3. Leave the refrigerator door open.
4. After defrosting (freezer compartment and fins free of frost), wipe the cabinet dry
with a cloth.
5. Use a cloth to mop up the water from the freezer compartment.
6. Switch the refrigerator back on again.
The layer of ice must never be removed forcibly, nor may defrosting be
accelerated using a heat source.
Note:
Water thawing in the main compartment of the refrigerator runs into an appropriate
container at the back of the refrigerator. From there, the water evaporates.
Positioning the storage rack
5.5
5.6
1. Fill the ice
cube tray with
drinking water.
2. Place the ice cube
tray in the freezer
compartment.
5.4
1. Loosen the front
and back securing
brackets.
2. Move the storage
rack to the left and
remove it.
Dismantling:
To fit the storage rack, the reverse order applies.
Only use drinking water!
1.
2.
14
Door locking
Switching off
Winter operation
Check that the ventilation grills have not been blocked by snow, leaves or similar.
5.8
5.9
5.7
1. Set energy selector switch (A)
to position "0". The appliance
is now fully switched off.
2. Secure the door open by means of the door
stop. The door will be slightly ajar. This is to
prevent mould from forming inside
the appliance.
A
Switching off gas operation
If the refrigerator is to be taken out of service for an extended period of
time, the on-board shut-off valve and the cylinder valve must be closed.
closed
open
When the ambient temperature falls below +8°C, the optional winter covers
should be fitted.
This protects the unit from excessively cold air.
Ventilation grille ( L500 )
Affix the cover
and fasten it.
You should also attach the winter cover if the vehicle is taken out of
service for a longer period or while it is being cleaned from the outside.
15
Interior light
Changing the light bulbs
Changing the decor panel
Dimensions of the panels in mm:
Model Height Width Thickness
all models RMT .... (upper door) 868,0+/-1 500,0+0/-1 2,5 max
(lower door) 263,0+/-1 500,0+0/-1 2,5 max
5.10
5.11
1. Remove cover.
2. Detach defective light
bulb.
3. Fit new light bulb
4. Clip the cover back in
place.
90°
1.
2.
Note:
For 12V DC :
1 light bulb 12V, 2W
1. Upper door
- remove the two screws holding the control panel
- unsrcew upper hinge pin (A) and remove the door
- unscrew upper part of the door frame and the panel
- insert new panel and fasten upper part of the door
frame
Please note: Carry out following steps BEFORE
mounting the upper door.
2. Lower door
- unscrew both screws of the middle hinge pin (B)
- Pull out door and hinge in an upwards direction
- unsrcrew lower part of the door frame and remove the
decor panel
- insert new panel and fasten lower part of the door
frame
- insert lower door and fasten the middle hinge
- insert upper door and fasten the upper hinge pin (A)
- replace the control panel
B
A
Please contact Dometic Service Centres for
replacement light bulbs.
RMT 7X50
RMT 7X51
RMT 7X55
16
Changing the doorhang5.12
It is not always possible to change the door when the refrigerator is installed.
1. Remove rotary knobs and unscrew control
panel.
Open the freezer door, unscrew the hinge (A)
screw and keep it to hand.
2. Take off the door by moving it upwards.
3. Unscrew middle
hinge and remove
lower door.
4. Remove the middle
hinge.
7. Affix the middle
hinge.
6. Positon the hinge at the
opposite side of the door
and insert lower door.
8. Insert freezer compartment door and fasten the upper hinge pin.
9. Replace the control panel and the rotary knobs.
5. Place hinge pin on the
opposite side.
5.
A
RMT 7X50
RMT 7X51
RMT 7X55
17
Troubleshooting5.13
Failure : The refrigerator does not work in gas operation mode.
Possible cause Action you can take
a.) Gas bottle empty.
b.) Is the supply cut-out device open?
c.) Air in the gas pipe?
a.) Change gas bottle.
b.) Open the cut-out device.
c.) Switch device off and on again 3-4 times to
remove air from the gas pipe.
Before calling the authorised Service Department, please check whether:
1. The instructions in the section "Using the refrigerator" have been followed.
2. The refrigerator is not tilted excessiveley.
3. It is possible to operate the refrigerator with an available power source.
Failure : The refrigerator does not work on 12V.
Possible cause Action you can take
a.) On-board fuse defective.
b.) On-board battery discharged.
c.) Engine not running.
a.) Fit new fuse.
b.) Check battery, charge it
c.) Start engine.
Failure : The refrigerator does not cool sufficiently.
Possible cause Action you can take
a.) Inadequate ventilation to the unit.
b.) The thermostat setting is too low.
c.) There is too much ice on the
condenser.
d.) Too much warm food put inside.
e.) Appliance running for a short time.
a.) Check that the ventilation grilles are not
covered.
b.) Turn the thermostat to a higher setting.
c.) Check that the refrigerator door seals
when shut.
d.) Let food cool down first.
e.) Wait several hours, check again.
Failure : The refrigerator does not work on 230V.
Possible cause Action you can take
a.) On-board fuse defective.
b.) No connection to supply voltage.
c.) AES: gas operation despite connection
to the supply voltage?
a.) Fit new fuse.
b.) Establish power connection.
c.) Appliance switches to gas operation due to
insufficient supply voltage (automatically
switches back to 230 V operation)
18
INSTRUCTIONS BAKING OVEN
Operating the oven
The use of the oven can lead to increases in warmth or dampness in the atmosphere
of the room in which it has been set up. Ensure that the cooking area is always well
ventilated. The oven is only to be used for baking. Under no circumstances do not
use it as a domestic heating unit!
When in operation, the oven gets very hot. Be careful to avoid children
coming into contact with the heated parts of the oven.
Insertion of pan and grate
Cleaning
It is recommended that, before using the oven for the first time, you clean it both
inside and outside. This cleaning should be repeated at regular intervals.
For cleaning, there should only be used household cleaning solutions of the
milder variety.
Use a soft cloth and lukewarm water
Then rinse the appliance with clean water and dry thoroughly.
6.0
6.1
The pan and the grate can be inserted
into the oven at three different heights.
Insert the grate into the oven in such a
manner that the fastenings which ensu-
re a raising of the grate from the oven
floor are lying on the inner side. This
ensures that the item placed in the
oven will not lie directly over
the naked gas flame
Wear protection gloves, using hot objects.
öffnen
6.2
6.1.1
WARNING
When the oven is in operation, it is necessarry to ensure additional
ventilation, i.e. by opening a window next to the baking oven.
Do not use the appliance as a domestic heating unit.
19
Turning the oven on
In order that the baking oven be ignited, the oven door must first have been
completely and securely closed.
Before using the oven for the first time, leave it in operation empty (i.e. without
any food inside it) but at the highest temperature for a duration of 30 minutes.
Igniting of the flame
The oven is equipped with an automatic igniter.
Should the burner flame go out, turn the regulator (J) back into the "O" position and wait
for at least 1 minute before you begin another process of ignition.
You should check the flame by looking closely at its shape and colour. It should be
mostly blue and display a clear, sharp outline. If the flame is burning irregularly and
unsteadily, have the oven checked over by authorized specialists.
Exchange of the igniter’s battery (RMT 7X50, oven only)
Winter operation
Check that the roof mounted flue outlet has not been blocked by snow, leaves or
similar.
3. In order to adjust the oven to the required temperature, release the knob from the depressed
position and turn it to the temperature, marked on the dial, which you require. The various knob
positions correspond to temperatures in various regions stretching up to 260°C.
1. Lightly depress the knob (J) and turn it to the left into the igni-
tion position. The ignition of the baking oven is possible in all knob
positions.
2. Firmly and fully depress the knob and hold it depressed.
The ignition begins automatically. Once the flame is burning, keep
the knob pressed down for a period of about 10 seconds.
J = switch on / thermostat (Oven)
A
B
C
D
E
J
J
6.3.1
6.3.2
6.3
6.4
Pull off carefully all the rotary knobs. Loosen two screws (Fig. 2) and remove the
fascia. The battery holder is accessable now..
Observe correct polarity when inserting the new battery (1.5V AAA/ R3 / Micro).
Fixing screws
Observe correct polarity !
Fig. 2 Fig. 3Fig. 1
20
GENERAL HINTS
Technical data
We reserve the right to make technical changes.
*Average consumption measured at an average ambient temperature of 25°C in pursuance of
ISO Standard.
Declaration of conformity
7.1
Model Dimensions Groos capacity Usable Connection * Consumption Netweight Gas-ignition
H x W x D (mm) incl. freezer capacity of Mains / Battery electricity / gas automatically
depth incl. door compartment freezer in 24 hrs
compartment
(Refrigerator) (Refrigerator) (Refrigerator)
7.2
7.0
RMT 7650(L) 1515x525x596 150 lit. 26 lit. 190W / 170 W ca.3,2 KWh / 380 g 59,0 kg
RMT 7850(L) 1515x525x651 175 lit. 31 lit. 190W / 170 W ca.3,2 KWh / 380 g 61,5 kg
RMT 7651(L) 1515x525x596 150 lit. 26 lit. 190W / 170 W ca.3,2 KWh / 380 g 59,0 kg X
RMT 7851(L) 1515x525x651 175 lit. 31 lit. 190W / 170 W ca.3,2 KWh / 380 g 61,5 kg X
RMT 7655(L) 1515x525x596 150 lit. 26 lit. 190W / 170 W ca.3,2 KWh / 380 g 59,0 kg X
RMT 7855(L) 1515x525x651 175 lit. 31 lit. 190W / 170 W ca.3,2 KWh / 380 g 61,5 kg X
CMBO 28 lit 100 g X
Oven * Consumption Gas-ignition
gas / hr automatically
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Dometic RMT7855L User manual
-
Dometic RMT7650L User manual
-
-
-
Dometic Replacement Water Valve Owner's manual
-
-
-
-
Dometic RGE 2000 User manual
-
Other documents
-
Everbilt 1259-110-RF Operating instructions
-
Electrolux RM4601 User manual
-
Marco XC-40A-60A User manual
-
Sibir (N-SR) S55GE User manual
-
Frigidaire S105GE User manual
-
Electrolux RC3000EGP User manual
-
-
Truma E-Kit Operating instructions
-
-
Sibir (N-SR) RC1100 User manual