Curtis Mathes TV VCR Combo CMC 19101 User manual

Brand: Curtis Mathes

Model: TV VCR Combo CMC 19101

Category: LCD TVs

Type: User manual

This manual is also suitable for

Customer Support: 1-800-270-4535

www.curtismathes.com

C M C 19101

OWNER'S MANUAL

19" COLOR TELEVISION / VCR

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK)

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intend-

ed to alert the user to the presence of uninsulated “dangerous voltage” within the

product’s enclosure that may be of sufficient magnitude to constitute a risk electric

shock.

The exclamation point within an equilateral triangle is intended to alert the user to

the presence of important operating and servicing instructions in the literature

accompanying the appliance.

WARNING

TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

CAUTION

CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE MANUFACTURER COULD

VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.

NOTE TO CATV SYSTEM INSTALLER

THIS REMINDER IS PROVIDED TO CALL THE CATV SYSTEM INSTALLER'S ATTENTION TO ARTICLE

820-40 OF THE NEC THAT PROVIDES GUIDELINES FOR PROPER GROUNDING AND, IN PARTICULAR,

SPECIFIES THAT THE CABLE GROUND SHALL BE CONNECTED TO THE GROUNDING SYSTEM OF

THE BUILDING, AS CLOSE TO THE POINT OF CABLE ENTRY AS PRACTICAL.

CAUTION

“CAUTION: TO PREVENT ELECTRICAL SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT,

FULLY INSERT” and “ATTENTION: POUR EVITER LES CHOCS ELECTRIQUES, INTRODUIRE LA LAME

LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER

JUSQU’AU FOND”

NOTE

Never connect the plug to an electrical source other than one providing AC 120V 60Hz power. Use only the attached

power cord. If the polarized AC cord does not fit into a non-polarized outlet, do not cut or file the blade. You are

responsible for having the obsolete outlet replaced with a polarized outlet.

If you feel a static discharge when touching the unit, and the unit does not function, simply unplug the unit from the

outlet. When you plug the unit back in, it should work normally.

Do not install power cords near any heating element or cooking appliances.

Precautions

LOCATION

For safe operation and satisfactory performance of your unit, keep the following in mind when

selecting a place for its installation :

• Shield it from direct sunlight and keep it away from sources of intense heat.

• Avoid dusty or humid places.

• Avoid places with insufficient ventilation for proper heat dissipation. Do not block the venti-

lation holes at the top and bottom of the unit. Do not place the unit on a carpet because this

will block the ventilation holes.

• Install the unit in a horizontal position.

• Avoid locations subject to strong vibration.

• Do not place the unit near strong magnetic fields.

• Do not move the unit from a cold place to a hot place or vice versa (see the warning below).

AVOID THE HAZARDS OF ELECTRICAL SHOCK AND FIRE

• Do not handle the power cord with wet hands.

• Do not pull on the power cord when disconnecting it from an ac wall outlet. grasp it by plug.

• If, by accident, water is spilled on your unit, unplug the power cord immediately and take the

unit to an authorized daewoo service center for servicing.

• Do not put your fingers or objects into the TV/VCR Combination cassette holder.

• Do not place anything directly on top of the unit.

WARNING

Mosture condensation may occur inside the unit when it is moved from a cold place to a warm

place, after heating in a cold room, or under conditions of high humidity. If a tape is played in

a TV/VCR Combination that has moisture, it may damage the tape and TV/VCR

Combination. When condensation occurs inside the unit, turn the power on and allow at least

2 hours for the unit to dry.

FCC WARNING

This equipment may generate or use radio frequency energy. Changes or modifications to this

equipment may cause harmful interference unless the modifications to this equipment are

expressly approved in the instruction manual.

The user could lose the authority to operate this equipment if an unauthorized change or modifi-

cation is made.

IMPORTANT COPYRIGHT INFORMATION

Unauthorized recording or use of broadcast television programming, video tape, film, or other

copyrighted material may violate applicable copyright laws. We assume no responsibility for

the unauthorized duplication, use or other acts which infringe upon the rights of copyright

owners.

SAFETY

IMPORTANT SAFEGUARDS

PLEASE READ ALL THESE INSTRUCTIONS REGARDING YOUR TV/VCR COMBINATION

AND RETAIN FOR FUTURE REFERENCE. FOLLOW ALL WARNINGS AND INSTRUCTIONS

MARKED ON THE TV/VCR COMBINATION.

1 Read all of these instructions.

2 Save these instructions for later use.

3 Unplug this TV/VCR Combination from the

wall outlet before cleaning. Do not use liquid

cleaners or aerosol cleaners. Use a damp

cloth for cleaning.

4 Do not use attachments not recommended by

the TV/VCR Combination manufacturer as

they may result in the risk of fire, electric

shock or other personal injury.

5 Do not use this TV/VCR Combination near

water, for example, near a bathtub, wash-

bowl, kitchen sink, or laundry tub, in a wet

basement, or near a swimming pool, or the

like.

6 Do not place this TV/VCR Combination on

an unstable cart, stand, or table. The

TV/VCR Combination may fall, causing

serious injury to a child or adult, and serious

damage to the equipment. Use only with a

cart or stand recommended by the manufac-

turer, or sold with the TV/VCR

Combination. Wall or shelf mounting should

follow the manufacturer's instructions, and

should use a mounting kit approved by the

manufacturer.

6A An appliance and cart combination should be

moved with care. Quick stops, excessive

force, and uneven surfaces may cause the

appliance and cart combination to overturn.

7 Slots and openings in the cabinet and the

back or bottom are provided for ventilation

and to ensure reliable operation of the

TV/VCR Combination; and to protect it

from overheating, these openings, must not

be blocked or covered. The openings should

never be blocked by placing the TV/VCR

Combination on a bed, sofa, rug, or other

similar surface. (This equipment should

never be placed near or over a radiator or

heat register.) This TV/VCR Combination

should not be placed in a built-in installation

such as a bookcase unless proper ventilation

is provided.

8 This TV/VCR Combination should be oper-

ated only from the type of power source indi-

cated on the marking label. If you are not

sure of the type of power supplied to your

home, consult your television dealer or local

power company.

9 This TV/VCR Combination is equipped with

a polarized alternating current line plug (a

plug having one blade wider than the other).

This plug will fit into the power outlet only

one way. This is a safety feature. If you are

unable to insert the plug fully into the outlet,

try reversing the plug. If the plug should still

fail to fit, contact your electrician to replace

your obsolete outlet. Do not defeat the safety

purpose of the polarized plug.

10 Do not allow anything to rest on the power

cord. Do not locate this TV/VCR

Combination where the cord will be abused

by persons walking on it.

11 Follow all warnings and instructions marked

on the TV/VCR Combination.

12 For added protection for this TV/VCR

Combination during a lightning storm, or

when it is left unattended and unused for

long periods of time, unplug it from the wall

outlet and disconnect the antenna or cable

system. This will prevent damage to the

equipment due to lightning and power-line

surges.

13 An outside antenna system should not be

located in the vicinity of overhead power

lines or other electric light or power circuits,

or where it can fall into such power lines or

circuits. When installing an outside antenna

system, extreme care should be taken to

keep from touching such power lines or cir-

cuits as contact with them might be fatal.

14 Do not overload wall outlets and extension

cords as this can result in fire or electric

shock.

15 Never push objects of any kind into this

TV/VCR Combination through openings as

they may touch dangerous voltage points or

short-out parts that could result in a fire or

electric shock. Never spill liquid of any kind

on the TV/VCR Combination.

16 Do not attempt to service this TV/VCR

Combination yourself as opening or remov-

ing covers may expose you to dangerous

voltage or other hazards. Refer all servicing

to qualified service personnel.

17 Unplug this TV/VCR Combination from the

wall outlet and refer servicing to qualified

service personnel under the following condi-

tions:

(a) When the power-supply cord or plug is

damaged or frayed.

(b) If liquid has been spilled, or objects have

fallen into the TV/VCR Combination.

exposed to rain or water.

(d) If the TV/VCR Combination does not

operate normally by following the oper-

ating instructions. Adjust only those con-

trols that are covered by the operating

instructions as an improper adjustment of

other controls may result in damage and

will often require extensive work by a

qualified technician to restore the

TV/VCR Combination to its normal

operation.

(e) If the TV/VCR Combination has been

dropped or the cabinet has been dam-

aged.

(f) When the TV/VCR Combination exhibits

a distinct change in performance - this

indicates a need for service.

18 When replacement parts are required, be

sure the service technician has used replace-

ment parts specified by the manufacturer

that have the same characteristics as the

original part. Unauthorized substitutions

may result in fire, electric shock or other

hazards.

19 Upon completion of any service or repairs to

this TV/VCR Combination, ask the service

technician to perform safety checks to deter-

mine that the television is in a safe operating

condition.

20 If an outside antenna or cable system is con-

nected to the television receiver, be sure the

antenna or cable system is grounded so as to

provide some protection against voltage

surges and built-up static charges.

Section 810 of the National Electrical Code,

ANSI/NFPA N0.70-1984, provides informa-

tion with respect to proper grounding of the

mast and supporting structure, grounding of

the lead-in wire to an antenna discharge unit,

size of grounding conductors, location of

antenna-discharge unit, connection to

grounding electrodes, and requirements for

the grounding electrode.

CurtisMathes

3100 West Big Beaver Rd.

Troy. MI 48084

1-800-270-4535

Dear Customer :

CurtisMathes would like to thank you for choosing this TV/VCR combination. It incorporates a host of features

designed to give you excellent performance for many years to come.

We realize that you’re eager to turn it on and begin enjoying the high-quality pictures it delivers just as quickly as

possible, but we ask you to take a few minutes to read the instructions in the booklet to familiarize yourself with the

receiver, its functions and some features which may be new to you. If you follow the instructions, this unit should

give you many years of viewing pleasure.

If for any reason it does not, we want to hear about it. Please write to us at the address above. CurtisMathes always

welcomes comments and suggestions on this or any of our other products.

On the other hand, when you discover the enjoyment, reliability and ease of use that is built into it, we hope that

you will tell your friends, and consider CurtisMathes when you make your next purchase of home entertainment

equipment.

In addition to TV/VCR combination, CurtisMathes produces a full line of audiovisual products built to the same

high design, engineering, and manufacturing standards as this unit.

Here are a few tips that will keep your TV/VCR Combination looking great and performing for years to come:

•Avoid putting it in excessively hot locations. Damage to the cabinet or premature component failures can result.

•There are ventilation holes in the bottom and rear of the cabinet. Make sure that they remain unobstructed. Do

not place the receiver on top of a thick cloth.

•If you don’t plan to use the receiver for several days, it’s a good idea to unplug it from the power outlet.

•Many common household cleaning agents, sprays, solvents, and polishes will cause permanent damage to the

surface of the cabinet. The best cleaning agents are mild soap and a damp cloth.

Again, thank you for choosing this CurtisMathes product. We have employed advanced engineering techniques in

its design, and manufactured it in one of the world’s most up-to-date production facilities. The result is a TV/VCR

Combination that we know you will be as proud to own as we were to create.

CurtisMathes

Table of Contents

Preface : Your New TV/VCR Combination 2

Features

Unpacking Your TV/VCR Combination 3

Chapter 1 : Overview of Your Equipment 4

Your TV/VCR Combination’s Front Panel

Your TV/VCR Combination’s Back Panel 5

Your Remote Controller 6

Chapter 2 : Connecting an Antenna or Cable to Your TV/VCR Combination 9

Connecting an Antenna 9

Connecting a Cable System 11

Connecting Other Pieces of Equipment 12

Safety Notes 12

Chapter 3 : Operating Your TV 13

Turning Your TV/VCR Combination On

Programming Your TV/VCR Combination’s Channel Memory 13

Changing Channels 14

Changing the Volume 14

Changing the TV/VCR Combination’s Channel Memory 15

Displaying the TV/VCR Combination’s Status during TV Operation 15

Adjusting Video Settings 16

Chapter 4 : Operating Your VCR 18

Video Cassette Tapes

Playing a Tape 19

Basic Recording 20

One Touch Recording (OTR) 21

Displaying the TV/VCR Combination’s Status during VCR Operation 22

Using the Counter (Zero Stop) 23

Chapter 5 : Using Timer Functions 24

Setting the Clock Automatically

Setting the Clock Manually 25

Setting the On Time 26

Setting the Off Time 26

Canceling the On Time or Off Time 27

Setting the Sleep Timer 28

Chapter 6 : Additional TV Features 29

Changing the Language of the On-Screen Menus

Captioning 29

CC on Mute 30

Power Restore 30

Parental Control Settings 31

Description of Parental Control Settings 32

Mini Glossary 33

Chapter 7 : Additional VCR Features

Programming to Record at a Later Time

Setting the Program Recording 35

Canceling the Program Record Settings 37

Displaying the Tape Counter 38

Auto Repeat PlayBack 39

Rental Play 39

Index Search (VISS) 40

Duplicating a Video Tape 41

Chapter 8 : Troubleshooting 42

Maintenance and specifications

Remote

CONTENTS

Preface : Your New TV/VCR Combination

PREFACE

Your New TV/VCR Combination

Congratulations on your purchase of a new CurtisMathes TV/VCR Combination. We hope you

find that your new TV/VCR Combination provides you with years of reliable performance.

Your new TV/VCR Combination is designed and engineered to provide you with the latest in

features for your convenience. Listed below are just a few of the many features of your equip-

ment.

Features

• Auto Power On

This feature automatically turns the TV/VCR Combination on when you insert a cassette.

• On-screen Programming

You can use simple on-screen menus to perform all of the major operating features of your

TV/VCR Combination, including programming to record.

• Tri-lingual Menus

You can choose to display the on-screen menus in English, French or Spanish.

• Auto Clock Setting

Your TV/VCR Combination can automatically set its internal clock based on a signal from

local PBS stations.

• Infrared Remote Control

The remote control included with your TV/VCR Combination allows you to complete almost

all operations from the comfort of your easy chair.

• 181 Channel Capability

Your TV/VCR Combination has an advanced tuner that can receive up to 181 channels.

• Closed Caption Decoder

Your TV/VCR Combination can decode the hidden text and captions that are broadcast with

many shows and are included on many videotapes.

• Record/Playback Speeds

Your TV/VCR Combination can recording to two speeds(SP, EP), playback to three speeds

(SP, LP, EP). SP(Standard Play), LP(Long Play), EP (Extend Play)

• Automatic Playback Speed Selection

Your TV/VCR Combination will automatically play a pre-recorded tape at the correct speed.

• Still Frame Capability

Your TV/VCR Combination can display a single frame from a video tape.

• Rental Play Mode

This special setting improves the playback quality of worn tapes, especially rental tapes.

• Repeat Playback

You can set your TV/VCR Combination to automatically repeat an entire video tape, or to

repeat the recorded part of a videotape.

Preface : Your New TV/VCR Combination

• Video Index Search System (VISS)

This feature allows you to find index marks on your tape quickly. Your TV/VCR

Combination places index marks at the beginning of each new recording.

• One Touch Recording (OTR)

You can quickly begin recording and set the length of time to record using just one button.

• 6 Event / 1 Month Timer Recording

You can program up to six different recording sessions up to a month in advance.

• Daily / Weekly Recording

You can easily set your VCR to record every day at the same time, or to record every week

at the same time.

• Sleep Timer

You can set your TV/VCR Combination to turn off after a certain amount of time passes,

from 15 minutes to 120 minutes.

• On Timer

You can set your TV/VCR Combination to turn on at a certain time.

• Parental Control

Parental control is on page 31.

Unpacking Your TV/VCR Combination

The following items are included with your TV/VCR Combination. If these items are missing,

please contact your CurtisMathes dealer immediately.

1 A remote control

2 A 300-ohm/75-ohm adaptor -> (13” only)

3 A rod antenna (“rabbit ears”) -> (13” only)

1 2 3

RECALL

REW PLAY FF

REC/OTR STOP

STILL

VISS

ATK

SLEED

SLOW

Chapter 1 : Overview of Your Equipment

CHAPTER

Overview of Your Equipment

Your TV/VCR Combination’s comes with a remote control. The section below summarizes

the buttons, controls, and terminals that you will use with your TV/VCR Combination.

Your TV/VCR Combination's Front Panel

Below you will find short description of the buttons and indicators on the front panel. These

are used for the following functions:

1 VIDEO in jack

Use this jack to receive a video signal from another A/V component.

2 AUDIO in jack

Use this jack to receive a audio signal from another A/V component.

3 EAR PHONE jack

Use this jack to the earphone (not supplied). The sound from the speaker is turned off.

4 Remote control receiver

This receiver receives a signal from your remote control. Do not block it.

5 STAND-BY(red) indicator

This indicator lights up when the power is off.

6 REC (red/green) indicator

This indicator lights up red when recording and lights up green when timer program oper-

ating.

7 REC button

Press this button to begin recording. Press repeatedly to set a recording time using

One-Touch Recording (OTR).

8 REW button

Press this button to rewind the tape.

9 PLAY button

Press this button to begin normal playback of the tape

10 FF button (Fast Forward)

Press this button to fast forward the tape.

VIDEO AUDIO

REC

1 2 3 4 6

789

10 11

12 13

POWER

STAND-BY REC

EAR PHONE

REW PLAY FF

STOP/EJECT

VOL CH

Chapter 1 : Overview of Your Equipment

11 STOP/EJECT button

Press this button when the tape is moving to stop the tape. Press this button when the tape

is stopped to eject it.

VOL

button (volume)

Press this button to change your TV/VCR Combination’s volume.

button (channel)

Press this button to change channels on your TV/VCR Combination. You will also use

these button to adjust the tracking.

14 POWER button

Press this button to turn your TV/VCR Combination on or off.

Your TV/VCR Combination’s Back Panel

1 Antenna terminal

Use this terminal to attach an antenna or cable

system to your TV/VCR Combination.

Your Remote Controller

1. POWER

Press this button to turn your TV/VCR

Combination on or off.

2. RECALL

Press this button to display the current time, the

counter, channel number and other status items.

3. TV/LINE

Press this button to select between viewing the

signal coming from the antenna terminal (TV) or

the signal coming from the A/V jack (LINE).

4. FAVORITE CH

Press this button to return to the previous channel

you were watching.

5. CANCEL

Press this button to erase timer program recording

settings.

6. C-RESET

Press this button to reset the counter to 0:00:00.

7. MUTE

Press to turn the TV/VCR Combination’s sound

on and off.

(TRK)

Press these buttons to change channels on your

TV/VCR Combination, or select items in the

menu system, or to adjust the tracking of a video

tape during playback.

VOL

Press these buttons to change your TV/VCR

Combination’s volume, to activate selections in

the menu system, or to change audio and video

settings.

10. MENU

Press this button to turn the TV/VCR Combination’s menu system on and off.

11. 0-9

Press these buttons to change channels.

12. SPEED

Press this button to select the SP, EP tape speed when the tape is recording.

13. C-Ø STOP

Press this button to find the counter zero.

Chapter 1 : Overview of Your Equipment

RECALL

TV/LINE

FAVORITE CH CANCEL

MUTEC-RESET

POWER

REW PLAY FF

REC/OTR STOP/EJECT PAUSE/STILL

VISS VISS

C H

VOL

C H

0 ATK

SPEED C- STOP

Chapter 1 : Overview of Your Equipment

14. 0(ATK)

Press this button to automatically set tracking point when the tape plays back.

15. REW

Press this button to rewind the tape.

17. FF button (Fast Forward)

Press this button to fast forward the tape.

18. PAUSE/STILL

Press to temporarily stop the tape during recording or playback.

19. REC/OTR

Press this button to begin recording. Press repeatedly to set a recording time using

One-Touch Recording (OTR)

20. STOP/EJECT

Press this button when the tape is moving to stop the tape. Press this button when the tape

is stopped to eject it.

21. VISS -

Press this button to find the most recent index mark on tape and begin playing.

22. VISS +

Press this button to find the next index mark on tape and begin playing.

Chapter 1 : Overview of Your Equipment

Installing Your Remote Control Batteries

1 Open the battery compartment on the back of the remote control.

2 Install two AAA-size batteries (not included) as shown. Make sure the “+” and “-” termi-

nals are oriented correctly.

3 Replace the cover.

Notes

Do not mix different types of batteries, or mix an old and a new battery.

Remove and replace weak batteries. Weak batteries can leak and damage your controller.

Dispose of batteries properly; never throw them into a fire.

Point your remote at the receiver on the center of the front of the TV/VCR Combination.

Make sure the receiver is not blocked.

The remote control can operate up to 30 feet away from the TV/VCR Combination, if you are

directly facing the front of the TV/VCR Combination. Operating distance diminishes as you

move to the sides of the TV/VCR Combination.

CHAPTER

Chapter 2 : Connecting an Antenna or Cable to Your TV/VCR Combination

Connecting an Antenna or Cable to Your TV/VCR Combination

Your TV/VCR Combination will provide you with the best performance if you connect it to

an external antenna or cable system. Follow the directions below to make this connection.

Please note that you will normally only have to make one of the connections shown below,

not all of them.

All connections will be made to the antenna terminal on the back of your TV/VCR

Combination. The antenna terminal is a silver metal post partially surrounded by two plastic

tabs. For help in locating the antenna terminal, see “Your TV/VCR Combination's Back

Panel” on page 5.

There is no antenna provided with your TV/VCR Combination.

Connecting an Antenna

If your antenna ends in a single coaxial lead,

simply press or screw the cable onto the antenna

terminal on the back of your TV/VCR

Combination.

If your antenna ends in a pair of 300 ohm twin leads, you must use a 300-ohm/75-ohm

adaptor. (An adaptor is included with your 19” TV/VCR Combination.) Place the leads under-

neath the screws on the adaptor, tighten the screws, then press the adaptor onto the antenna

terminal on the back of the TV/VCR Combination Combination.

Chapter 2 : Connecting an Antenna or Cable to Your TV/VCR Combination

Antennas with two sets of leads

You might have two sets of leads from your antenna system, especially if you have one anten-

na for VHF signals and one antenna for UHF signals.

If your antenna system has both a coaxial lead and twin 300-ohm leads, you must obtain a

combiner (available at your local electronics store). Press or screw the coaxial lead onto the

combiner; place the twin leads underneath the screws on the combiner and tighten the screws.

Press the cable from combiner onto the antenna terminal on the back of the TV/VCR

Combination.

If your antenna system has two sets of twin 300-ohm leads, you must obtain a combiner

(available at your local electronics store). Place one set of twin leads underneath the screws on

the combiner and tighten the screws. Do the same with the other set of twin leads. Press the

cable from the combiner onto the antenna terminal on the back of your TV/VCR

Combination.

Chapter 2 : Connecting an Antenna or Cable to Your TV/VCR Combination

Connecting a Cable System

If your cable set-up is not described below, please contact your cable company for more infor-

mation.

If your cable system does not require the use of a

cable box, simply press or screw the incoming cable

onto the antenna terminal on the back your TV/VCR

Combination.

If your cable system requires you to use a converter box for all channels, connect the

incoming cable to the IN terminal on the converter box. Connect another cable between the

OUT terminal on the converter box and the antenna terminal on the TV/VCR Combination.

You will need to keep your TV/VCR Combination tuned to channel 3 or 4 and change chan-

nels using the converter box.

If your cable system only requires you to use a converter box for some channels (i. e.

pay-TV channels), follow these steps: Find the primary incoming coaxial cable. Plug this

cable into a splitter (available at your local electronics store). Connect one coaxial cable

between one OUT terminal on the splitter and the IN terminal on the converter box. Connect

another coaxial cable between the other OUT terminal on the splitter and the A-IN terminal on

an A/B switch (available at your local electronics store.) Connect a third coaxial cable

between the OUT terminal on the converter box and the B-IN terminal on the A/B switch.

Finally, connect a coaxial cable between the OUT terminal on the A/B switch and the antenna

terminal on the back of your TV/VCR Combination.

When the A/B switch is in the A position, you can change channels on the TV/VCR

Combination; when the A/B switch is in the B position, you, need to change channels on the

converter box (and your TV should be tuned to channel 3 or 4)

Connecting Other Pieces of Equipment

You may want to connect a VCR, laser disc player, satellite receiver, or another type of equip-

ment to your TV/VCR Combination. We recommend that you follow the instructions included

with the piece of equipment you wish to connect.

If you connect other pieces of equipment to your TV/VCR Combination using the audio/video

jacks on the front panel, you will need to use the TV/LINE button on the remote control to

view the signal coming through these jacks. See page 41 for more information.

Safety Notes

If you plan on being away from your home for an extended period of time, or if a thunder-

storm is approaching, you should unplug your television, and you may wish to disconnect

your TV from a rooftop or satellite antenna. You do not need to disconnect your TV from a

cable system.

Chapter 2 : Connecting an Antenna or Cable to Your TV/VCR Combination

Chapter 3 : Operating Your TV

CHAPTER

Operating Your TV

Once you have connected your TV/VCR Combination to an antenna or cable system, plugged

the TV in, and put batteries in the remote, you are ready to use the TV. The first thing you

should do is program your TV/VCR Combination so it memorizes all of available channels.

Turning Your TV/VCR Combination On

1. To turn your TV/VCR Combination, press the POWER button on the

remote control. You can also use the POWER button on the front

panel. Make sure your TV is plugged in before you try to turn it on.

Programming Your TV/VCR Combination's Channel Memory

Your TV/VCR Combination's memory determines the channels that are available using the

VCHW buttons. If a channel is not in memory, you can tune to it with the number buttons,

but not with the VCHW buttons. Follow these steps to program your TV/VCR Combination's

memory:

1. With the TV on, press the MENU button until “Set-Up” menu is displayed.

2. Use the VCHW buttons to select “Reception”, then use the VOLB button to select ‘Air’

or ‘Cable’. If you connected an antenna to your TV/VCR Combination, select ‘Air’; If you

connected a cable system, select ‘Cable’.

3. Use the VCHW buttons to select “Memorize Channels”, then use the VOLB button to

enter the “Memorize Channels” process.

4. Press the MENU button to return to Set-Up menu.

5. Press the MENU button to return to normal TV viewing.

Your TV/VCR Combination's channel memory will not be affected by a power outage. You

will not need to re-program the memory unless you change the type of cable or antenna con-

nected to your TV/VCR Combination.

RECALL

TV/LINE

FAVORITE CH CANCEL

MUTEC-RESET

POWER

REW PLAY FF

REC/OTR STOP STILL

VISS VISS

C H

VOL

C H

0 ATK

SLEED SLOW

Select

Language : English

Reception : Air

Memorize Channels

Add/Delete Channels

Adjust Exit

Set-Up

Select

Language : English

Reception : Air

Memorize Channels

Add/Delete Channels

Enter Exit

3-1

Set-Up

Select

Language : English

Reception : Air

Memorize Channels

Add/Delete Channels

Adjust Exit

Set-Up

Memorize Channels

Air 11

Memorizing all air channels.

Please, stand by.

Press MENU to cancel and

return to Set-Up menu.

3-2

Select

Language : English

Reception : Air

Memorize Channels

Add/Delete Channels

Enter Exit

Set-Up

Chapter 3 : Operating Your TV

Changing Channels

You can change channels in three ways:

1. The VCHW buttons will take you through all memorized chan-

nels, one by one. The VCHW buttons will not access channels

that have not been programmed into the TV’s memory. For

more information about programming channels into memory,

see the section “Programming your TV/VCR Combination’s

Channel Memory” on the previous page.

2. The number buttons (0-9) will take you to any channel, even if it

has not been memorized. To change to a channel, enter its num-

ber; the TV/VCR Combination will tune to the new channel

when you enter the second digit of the channel.

3. The FAVORITE CH button will take you instantly to the last

channel you were watching.

Changing the Volume

1. To change the volume of the TV/VCR Combination set, use the

CVOLB buttons on the remote or on the front panel.

2. To quickly turn off the sound, press the MUTE button on the

remote. The ‘MUTE’ will appear on screen, colored green. To

return the volume to its previous level, press MUTE again.

RECALL

TV/LINE

FAVORITE CH CANCEL

MUTEC-RESET

POWER

REW PLAY FF

REC/OTR STOP STILL

VISS VISS

C H

VOL

C H

0 ATK

SLEED SLOW

RECALL

TV/LINE

FAVORITE CH CANCEL

MUTEC-RESET

POWER

REW PLAY FF

REC/OTR STOP STILL

VISS VISS

C H

VOL

C H

0 ATK

SLEED SLOW

RECALL

TV/LINE

FAVORITE CH CANCEL

MUTEC-RESET

POWER

REW PLAY FF

REC/OTR STOP STILL

VISS VISS

C H

VOL

C H

0 ATK

SLEED SLOW

RECALL

TV/LINE

FAVORITE CH CANCEL

MUTEC-RESET

POWER

REW PLAY FF

REC/OTR STOP STILL

VISS VISS

R-39N01

C H

VOL

C H

0 ATK

SLEED SLOW

RECALL

TV/LINE

FAVORITE CH CANCEL

MUTEC-RESET

POWER

REW PLAY FF

REC/OTR STOP STILL

VISS VISS

C H

VOL

C H

0 ATK

SLEED SLOW

Page is loading ...

Curtis Mathes TV VCR Combo CMC 19101 User manual

Brand: Curtis Mathes

Model: TV VCR Combo CMC 19101

Category: LCD TVs

Type: User manual

This manual is also suitable for

Download PDF

report

Curtis Mathes TV VCR Combo CMC 19101 User manual

This manual is also suitable for

Curtis Mathes TV VCR Combo CMC 19101 User manual

Related papers

Other documents