Electrolux ESF46710W User manual

Brand: Electrolux

Model: ESF46710W

Category: Dishwashers

Type: User manual

This manual is also suitable for

ESF46710X

Electrolux ESF46710W is a dishwasher offering several features and functions to help you achieve sparkling clean dishes. It has a water softener to remove minerals and salts from the water supply, ensuring optimal performance and preventing limescale buildup. You can adjust the water softener level based on the hardness of your water. The dishwasher also features a salt container that needs to be filled with dishwasher salt to aid in the softening process. Additionally, it has a rinse aid dispenser to enhance drying results and prevent water spots on your dishes.

user manual

Dishwasher

ESF 46710

Electrolux. Thinking of you.

Share more of our thinking at www.electrolux.com

Contents

Safety information 2

Product description 4

Control panel 5

First use 6

Set the water softener 6

Use of dishwasher salt 7

Use of rinse aid 8

Daily use 9

Load cutlery and dishes 10

Use of detergent 13

Multitab function 14

Select and start a washing programme

Unloading the dishwasher 16

Washing programmes 16

Care and cleaning 17

What to do if… 18

Technical data 20

Hints for test institutes 20

Installation 21

Water connection 22

Electrical connection 24

Environment concerns 24

Subject to change without notice

Safety information

In the interest of your safety and to en-

sure the correct use, before installing

and first using the appliance, read this

user manual carefully, including its hints

and warnings. To avoid unnecessary

mistakes and accidents, it is important

to ensure that all people using the appli-

ance are thoroughly familiar with its op-

eration and safety features. Save these

instructions and make sure that they re-

main with the appliance if it is moved or

sold, so that everyone using it through

its life will be properly informed on appli-

ance use and safety.

Correct use

• This dishwasher is only intended for wash-

ing household utensils suitable for ma-

chine washing.

• Do not put any solvents in the dishwasher.

This could cause an explosion.

• Knives and other items with sharp points

must be loaded in the cutlery basket with

their points down or placed in a horizontal

position in the upper basket.

• Only use products (detergent, salt and

rinse aid) suitable for dishwashers.

• Avoid opening the door whilst the appli-

ance is in operation, hot steam may es-

cape.

• Do not take any dishes out of the dish-

washer before the end of the washing cy-

cle.

• After use, isolate the appliance from the

power supply and turn off the water sup-

ply.

• This product should be serviced only by an

authorized service engineer, and only gen-

uine spare parts should be used.

• Under no circumstances should you at-

tempt to repair the machine yourself. Re-

pairs carried out by inexperienced persons

could cause injury or serious malfunction-

ing. Contact your local Service Force Cen-

tre. Always insist on genuine spare parts.

General safety

• Persons (including children) with reduced

physical sensory, mental capabilities or

lack of experience and knowledge must

not use the appliance. They must have su-

pervision or instruction for the operation of

the appliance by a person responsible for

their safety.

2 electrolux

• Dishwasher detergents can cause chemi-

cal burns to eyes, mouth and throat. Could

endanger life! Comply with the safety in-

structions of the dishwasher detergent

manufacturer.

• Water in the dishwasher is not for drinking

purposes. Detergent residue may still be

present in your machine.

• Ensure that the door of the dishwasher is

always closed when it is not being loaded

or unloaded. In this way you will avoid any-

body tripping over the open door and hurt-

ing themselves.

• Do not sit or stand on the open door.

Child safety

• This appliance is designed to be operated

by adults. Children must be supervised to

ensure that they do not play with the ap-

pliance.

• Keep all packaging well away from chil-

dren. There is a risk of suffocation.

• Keep all detergents in a safe place out of

children’s reach.

• Keep children well away from the dish-

washer when the door is open.

Installation

• Check your dishwasher for any transport

damage. Never connect a damaged ma-

chine. If your dishwasher is damaged con-

tact your supplier.

• All packaging must be removed before

use.

• Any electrical and plumbing work required

to install this appliance must be carried out

by a qualified and competent person.

• For safety reasons it is dangerous to alter

the specifications or attempt to modify this

product in any way.

• Never use the dishwasher if the electrical

supply cable and water hoses are dam-

aged; or if the control panel, work top or

plinth area are damaged such that the in-

side of the appliance is freely accessible.

Contact your local Service Force centre, in

order to avoid hazard.

• All sides of the dishwasher must never be

drilled to prevent damage to hydraulic and

electric components.

Warning! For electrical and water

connection carefully follow the

instructions given in the specific

paragraphs.

electrolux 3

Product description

1 Upper basket

2 Water hardness dial

3 Salt container

4 Detergent dispenser

5 Rinse aid dispenser

6 Rating plate

7 Filters

8 Lower spray arm

9 Upper spray arm

10 Worktop

4 electrolux

Control panel

1 On/Off button

2 Programme selection buttons

3 Delay start button (Delay)

4 Indicator lights

5 Digital display

6 Function buttons

Indicator lights

Programme in progress

Comes on when a washing programme is set and

remains on for all the duration of the washing pro-

gramme.

Goes off when the washing programme has

ended.

End

Comes on when a washing programme has

ended.

Multitab function

Indicates the activation/deactivation of the multi-

tab function. Refer to 'Multitab function'.

Salt

Comes on when the special salt has run out.

Rinse aid

Comes on when the rinse aid has run out.

1) The salt and rinse aid indicator lights never come on while a washing programme is running even if

filling with salt and/or rinse aid is necessary.

The digital display

The digital display indicates:

• the level of hardness to which the water

softener is set,

electrolux 5

• the approximate remaining time of the run-

ning programme,

• activation/deactivation of the rinse aid dis-

penser ( ONLY with 'Multitab function' ac-

tive),

• the end of a washing programme (a zero

will appear in the digital display),

• the countdown for the delay start,

• fault codes concerning malfunction of the

dishwasher.

Function buttons

The following functions can be set using

these buttons:

• the adjustment of the water softener level,

• cancel a washing programme or a delay

start in progress,

• activate/deactivate the Multitab function,

• activate/deactivate the rinse aid dispenser

when the Multitab function is active.

Setting mode

Press the On/Off button; if ALL programme

button lights come on, the appliance is in

setting mode.

Always remember that when performing

the following operations:

– selecting a washing programme,

– setting the water softener level,

– activating/deactivating the rinse aid,

the appliance MUST be in setting mode.

Press the On/Off button; if a programme but-

ton light comes on, the last performed or se-

lected programme is still set. In this case, to

return to setting mode, the programme has

to be cancelled.

To cancel a set programme or a

programme in progress

Simultaneously press and hold the two func-

tion buttons B and C until all the programme

button lights come on. The programme has

been cancelled and the machine is now in

setting mode.

First use

Before using your dishwasher for the first

time:

• Ensure that the electrical and water con-

nections comply with the installation in-

structions

• Remove all packaging from inside the ap-

pliance

• Set the water softener level

• Pour 1 litre of water into the salt container

and then fill with dishwasher salt

• Fill the rinse aid dispenser

If you want to use combi detergent

tablets such as: ''3 in 1'', ''4 in 1'', ''5

in 1'' etc... set the Multitab function.

(See ''Multitab function'').

Set the water softener

The dishwasher is equipped with a water

softener designed to remove minerals and

salts from the water supply, which would

have a detrimental or adverse effect on the

operation of the appliance.

The higher the content of these minerals and

salts, the harder your water is. Water hard-

ness is measured in equivalent scales, Ger-

man degrees (dH°), French degrees (°TH)

and mmol/l (millimol per litre - international

unit for the hardness of water).

The softener should be adjusted according

to the hardness of the water in your area.

Your local Water Authority can advise you on

the hardness of the water in your area.

The water softener must be set in two

ways: manually, using the water hard-

ness dial and electronically.

Water hardness Adjusting the water hardness setting Use of

salt

°dH °TH mmol/l manually electronically

51 - 70 91 - 125 9,1 - 12,5 2 level 10 yes

43 - 50 76 - 90 7,6 - 9,0 2 level 9 yes

6 electrolux

Water hardness Adjusting the water hardness setting Use of

salt

°dH °TH mmol/l manually electronically

37 - 42 65 - 75 6,5 - 7,5 2 level 8 yes

29 - 36 51 - 64 5,1 - 6,4 2 level 7 yes

23 - 28 40 - 50 4,0 - 5,0 2 level 6 yes

19 - 22 33 - 39 3,3 - 3,9 2 level 5 yes

15 - 18 26 - 32 2,6 - 3,2 1 level 4 yes

11 - 14 19 - 25 1,9 - 2,5 1 level 3 yes

4 - 10 7 - 18 0,7 - 1,8 1 level 2 yes

< 4 < 7 < 0,7 1 level 1 no

Setting manually

The dishwasher is factory set at position

1. Open the dishwasher door.

2. Remove the lower basket from the dish-

washer.

3. Turn the water hardness dial to position

1 or 2 (see chart).

4. Replace the lower basket.

Setting electronically

The dishwasher is factory set at level 5.

1. Press the On/Off button. The dishwasher

must be in setting mode.

2. Simultaneously press and hold function

buttons B and C , until the lights of func-

tion buttons A , B and C start flashing.

Press function button A , the lights of

function buttons B and C go off while the

light of function button A continues to

flash. The current level shows on the dig-

ital display.

Examples:

displayed = level 5

displayed = level 10

4. To change the level, press function but-

ton A . Each time the button is pressed

the level changes. (For the selection of the

new level see the chart).

Examples: If the current level is 5, by

pressing function button A once, level 6

is selected. if the current level is 10, by

pressing function button A once, level 1

is selected.

5. To memorize the operation, switch off the

dishwasher by pressing the On/Off but-

ton.

Use of dishwasher salt

Warning!

Only use salt specifically designed for use in

dishwashers. All other types of salt not spe-

cifically designed for use in a dishwasher, es-

pecially table salt, will damage the water soft-

ener. Only fill with salt just before starting one

of the complete washing programmes. This

will prevent any grains of salt or salty water,

which may have been spilt, remaining on the

bottom of the machine for any period of time,

which may cause corrosion.

To fill:

1. Open the door, remove the lower basket

and unscrew the cap of the salt container

by turning it anticlockwise.

2. Pour 1 litre of water into the container

(this is necessary only before filling

with salt for the first time) .

3. Using the funnel provided, pour in the salt

until the container is full.

electrolux 7

4. Replace the cap making sure that there

is no trace of salt on the screw thread or

on the gasket.

5. Replace the cap tightly turning it clock-

wise until it stops with a click.

Do not worry if water overflows from the

unit when filling with salt, this is quite

normal.

The salt indicator light on the control

panel can remain illuminated for 2-6

hours after the salt has been replen-

ished, assuming the dishwasher re-

mains switched on. If you are using

salt that takes longer to dissolve

then this can take longer. The oper-

ation of the machine is not affected.

Use of rinse aid

Warning! Only use branded rinse aid for

dishwashers.

Never fill the rinse aid dispenser with any

other substances (e.g. dishwasher

cleaning agent, liquid detergent). This

would damage the appliance.

Rinse aid ensures thorough rinsing, and

spot and streak free drying.

Rinse aid is automatically added during

the last rinse.

1. Open the container by pressing the re-

lease button (A).

2. Add the rinse aid in the container. The

maximum level for filling is indicated by

"max".

The dispenser holds about 110 ml of rinse

aid, which is sufficient for between 16 and

40 washing cycles, depending upon the

dosage setting.

3. Ensure that the lid is closed after every

refill.

Clean up any rinse aid spilt during filling

with an absorbent cloth to avoid excess

foaming during the next wash.

According to the finish and drying results ob-

tained, adjust the dose of rinse aid by means

of the 6 position selector (position 1 minimum

dosage, position 6 maximum dosage).

The dose is factory set in position 4.

Increase the dose if there are drops of water

or lime spots on the dishes after washing.

8 electrolux

Reduce it if there are sticky whitish streaks

on the dishes or a bluish film on glassware or

knife blades.

Daily use

• Check if it’s necessary to refill with dish-

washer salt or rinse aid.

• Load cutlery and dishes into the dishwash-

er.

• Fill with dishwasher detergent.

• Select a wash programme suitable for the

cutlery and dishes.

• Start the wash programme.

Helpful hints and tips

Sponges, household cloths and any object

that can absorb water may not be washed in

the dishwasher.

• Before loading the dishes, you should:

– Remove all left over food and debris.

– Soften remnants of burnt food in pans

• When loading the dishes and cutlery,

please note:

– Dishes and cutlery must not impede the

rotation of the spray arms.

– Load hollow items such as cups,

glasses, pans, etc. with the opening

downwards so that water cannot collect

in the container or a deep base.

– Dishes and items of cutlery must not lie

inside one another, or cover each other.

– To avoid damage to glasses, they must

not touch.

– Lay small objects in the cutlery basket.

• Plastic items and pans with non stick coat-

ings have a tendency to retain water

drops; these items will not dry as well as

porcelain and steel items.

• Light items (plastic bowls etc.) must be

loaded in the upper basket and arranged

so they do not move.

For washing in the dishwasher the following cutlery and dishes

are not suitable: are of limited suitability:

• Cutlery with wooden, horn, china or mother-of-

pearls handles.

• Plastic items that are not heat resistant.

• Older cutlery with glued parts that are not tem-

perature resistant.

• Bonded cutlery items or dishes.

• Pewter or copper items.

• Lead crystal glass.

• Steel items prone to rusting.

• Wooden platters.

• Items made from synthetics fibres.

• Only wash stoneware in the dishwasher if it is

specially marked as being dishwasher-safe by

the manufacturer.

• Glazed patterns may fade if machine washed

frequently.

• Silver and aluminium parts have a tendency to

discolour during washing: Residues, e.g. egg

white, egg yolk and mustard often cause dis-

colouring and staining on silver. Therefore al-

ways clean left-overs from silver immediately, if

it is not to be washed straight after use.

electrolux 9

Load cutlery and dishes

The lower basket

The lower basket is designed to take sauce-

pan, lids, plates, salad bowls, cutlery ect.

Service dishes and large lids should be ar-

ranged around the edge of the basket, en-

suring that the spray arms can turn freely.

The rows of prongs in the lower basket can

lie flat to allow you to load pots, pans and

bowls.

The cutlery basket

Long bladed knives stored in an upright

position are a potential hazard. Long

and/or sharp items of cutlery such as

carving knives must be positioned

horizontally in the upper basket. Take

care when loading or unloading sharp

items such as knives.

Forks and spoons should be placed in the

removable cutlery basket with the handles

facing downwards and the knives with their

handles facing upwards.

If the handles protrude from the bottom of the

basket, obstructing the lower spray arm, load

the cutlery with the handles facing upwards.

Mix spoons with other cutlery to prevent

them from sticking together.

To make loading of the cutlery basket easier,

lower the cutlery basket handle.

10 electrolux

For best results we recommend that you use

the cutlery grid.

If the size and dimensions of the cutlery do

not allow the use of the grid, it can be easily

hidden.

The upper basket

The upper basket is designed for plates (des-

sert plates, saucers, dinner plates of up to 24

cm in diameter), salad bowls, cups and

glasses

Arrange items on and underneath the cup

racks so that water can reach all surfaces.

Glasses with long stems can be placed up-

side down in the cup racks.

For taller items, the cup racks can be folded

upwards.

Mini cutlery basket

The upper basket is supplied with a mini cut-

lery basket.

Caution! NEVER PUT KNIVES IN THE

MINI CUTLERY BASKET. THIS WILL

PREVENT DAMAGE TO THE

APPLIANCE.

Place the mini cutlery basket in the front part

of the upper basket, only on the left-hand

side.

electrolux 11

The dimensions of the cutlery depend on the

position of the upper basket. Refer to the fol-

lowing table.

Cutlery dimensions for mini cutlery basket

Upper basket in higher

position

maximum 15 cm

Upper basket in lower

position

maximum 20 cm

Soft spikes

Soft spikes impede glassware to move dur-

ing the washing cycle or when the upper

basket is moved.

Refer to the figures for a correct positioning

of the soft spikes. They can only be posi-

tioned on right-hand side of the basket.

Once positioned correctly, press them down

firmly and make sure they do not move.

Caution! BEFORE CLOSING THE

DOOR, MAKE SURE THAT THE SPRAY

ARMS CAN ROTATE FREELY.

Adjusting the height of the upper basket

If washing very large plates you can load

them in the lower basket after moving the

upper basket to the higher position.

Maximum height of the dishes in:

the upper

basket

the lower

basket

With upper

basket raised

20 cm 31 cm

With upper

basket low-

ered

24 cm 27 cm

To move to the higher position proceed

as follows:

1. Pull out the basket until it stops.

12 electrolux

2. Carefully lift both sides upwards until the

mechanism is engaged and the basket is

stable.

To lower the basket to the original posi-

tion proceed as follows:

1. Pull out the basket until it stops.

2. Carefully lift both sides upwards and then

allow the mechanism to drop back down

slowly, keeping hold of it.

Never lift or lower the basket on one side

only

When the basket is in the higher position

cups cannot be placed on the cup racks.

After loading your machine always

close the door, as an open door can

be a hazard.

Use of detergent

Only use detergents specifically de-

signed for use in dishwashers.

Please observe the manufacturer’s dos-

ing and storage recommendations as

stated on the detergent packaging.

Using no more than the correct amount

of detergent contributes to reducing pol-

lution.

Fill with detergent

1. Open the lid.

2. Fill the detergent dispenser (1) with de-

tergent. The marking indicates the dosing

levels:

20 = approximately 20 g of detergent

30 = approximately 30 g of detergent.

3. All programmes with prewash need an

additional detergent dose (5/10 g) that

must be placed in the prewash detergent

chamber (2).

This detergent will be used during the

prewash phase.

When using detergent tablets; place the

tablet in compartment (1)

electrolux 13

4. Close the lid and press until it locks in

place.

Detergent tablets from different manu-

facturers dissolve at different rates. For

this reason, some detergent tablets do

not attain their full cleaning power during

short washing programmes. Therefore,

please use long washing programmes

when using detergent tablets, to ensure

the complete removal of detergent re-

siduals.

Multitab function

This appliance is equipped with the "Multitab

function", that allows the use of the "Multitab"

combi detergent tablets.

These products are detergents with a com-

bined cleaning, rinsing and salt functions.

They can also contain other different agents

depending on which kind of tablets you

choose ("3 in 1", "4 in 1", "5 in 1" etc...).

Check whether these detergents are suitable

for your water hardness. See the manufac-

turers instructions.

Once this function is selected it will remain

active for all following wash programmes.

With the selection of this function the inflow

of rinse aid and salt from each respective

supply container is automatically deactivated

and also the indicator lights for salt and rinse

aid are deactivated.

When using the "Multitab function", the cycle

durations may change. If this is the case, the

running time for the programme is automat-

ically updated on the digital display.

Activate/deactivate the ''Multitab func-

tion'' before the start of a washing pro-

gramme.

Once the programme is running, the

"Multitab function " can NO longer be

changed. If you want to cancel the "Mul-

titab function " you have to cancel the

programme setting and then deactivate

the ''Multitab function''. In this case you

have to set a washing programme (and

desired options) again.

Activation/deactivation of the Multitab

function

Simultaneously press and hold the two Mul-

titab buttons (function buttons D and E ) until

the Multitab indicator light comes on. This

means that the function is active.

To deactivate the function press the same

buttons again until the indicator light corre-

sponding to the Multitab function symbol

goes off.

If the drying results are not satisfac-

tory we suggest that you:

1. Fill up the rinse aid dispenser with

rinse aid.

2. Activate the rinse aid dispenser.

3. Set the rinse aid dosage to position

• The activation/deactivation of the

rinse aid is only possible with the Mul-

titab function active.

Activation/deactivation of the rinse aid

dispenser

1. Press the On/Off button. The dishwasher

must be in setting mode.

2. Simultaneously press and hold function

buttons B and C , until the lights of func-

tion buttons A , B , and C start flashing.

3. Press function button B , the lights of

function buttons A and C go off while the

light of function button B continues to

flash. The digital display indicates the cur-

rent setting.

Rinse aid dispenser deactivated

14 electrolux

Rinse aid dispenser activated

4. To change the setting, press button B

again, the digital display indicates the

new setting.

5. To memorize the operation, switch off the

dishwasher by pressing the On/Off but-

ton.

If you decide to revert back to the

use of individual detergents we ad-

vise that you:

1. Deactivate the Multitab function.

2. Fill up the salt container and the rinse

aid dispenser again.

3. Adjust the water hardness setting to

the highest setting and perform 1

normal washing programme without

loading any dishes.

4. Adjust the water hardness setting

according to the hardness of the wa-

ter in your area.

5. Adjust the rinse aid dosage.

Select and start a washing programme

Select the washing programme and

delay start with the door slightly

opened. The start of the programme

or the countdown of the delay start

will occur only after the closure of

the door. Until then it is possible to

modify the settings

1. Check that the baskets have been loaded

correctly and that the spray arms are free

to rotate.

2. Check that the water tap is opened.

3. Press the On/Off button. The dishwasher

must be in setting mode.

4. Press the button corresponding to the re-

quired programme (see ''Washing pro-

grammes'' chart).

When a programme has been selected

the corresponding light comes on.

The programme in progress indicator

light comes on.

Close the dishwasher door, the pro-

gramme starts automatically.

The programme in progress indicator

light remains on.

Setting and starting the programme with

delay start

1. After having selected the washing pro-

gramme, press the delay start button until

the flashing number of hours for the delay

start appear in the digital display. The

start of the selected washing programme

can be delayed for between 1 and 19

hours.

2. Close the dishwasher door, the count-

down starts automatically. The number in

the display is no longer flashing but fixed

with static light.

3. The countdown will decrease with steps

of 1 hour.

4. The opening of the door will interrupt the

countdown. Close the door; the count-

down will continue from the point at

which it was interrupted.

5. Once the delay start has elapsed the pro-

gramme will start automatically.

With the delay start function set, the

programme in progress indicator light

is off. Once the countdown of the delay

start has elapsed, the washing pro-

gramme will start automatically and the

programme in progress indicator light

comes on.

The selection of the washing pro-

gramme and delay start can occur also

with the door closed.

When you press a programme button

you have ONLY 3 seconds to select a

different programme or a delay start.

After these 3 seconds, the selected pro-

gramme starts automatically.

Warning! Interrupt or cancel a

washing programme in progress

ONLY if it's absolutely necessary.

Attention! Hot steam may escape

when the door is opened. Open the

door carefully.

Interrupt a washing programme in

progress

• Open the dishwasher door; the pro-

gramme will stop. Close the door; the pro-

gramme will start from the point at which

it was interrupted.

• Press the On/Off, all indicator lights will go

off. Press the On/Off button again; the pro-

gramme will start from the point at which

it was interrupted.

electrolux 15

Cancel a delay start or a washing

programme in progress

• Simultaneously press and hold the two

function buttons B and C until all the pro-

gramme lights come on.

• Cancelling a delay start will also cancel the

washing programme. You have to select

the washing programme again.

• If a new washing programme is to be se-

lected, check that there is detergent in the

detergent dispenser.

End of the washing programme

• The dishwasher will automatically stop and

the programme in progress indicator

light goes off.

•The End indicator light comes on.

• The light of the programme just ended re-

mains on.

• Zero appears in the digital display.

1. Switch off the dishwasher by pressing the

On/Off button.

2. Open the dishwasher door, leave it ajar

and wait a few minutes before removing

the dishes; this way they will be cooler

and the drying will be improved.

Standby mode

If you do not switch off the appliance at the

end of the washing programme, the appli-

ance automatically goes into standby mode.

The standby mode decreases energy con-

sumption.

Three minutes after the end of the pro-

gramme, all indicator lights go off and the

digital display shows one horizontal bar.

Press one of the buttons (not the on/off but-

ton), to go back to end-of-programme mode.

Unloading the dishwasher

• Hot dishes are sensitive to knocks. The

dishes should therefore be allowed to cool

down before removing from the appliance.

•Empty the lower basket first and then the

upper one; this will avoid water dripping

from the upper basket onto the dishes in

the lower one.

• Water may appear on the sides and the

door of the dishwasher as the stainless

steel will eventually become cooler than

the dishes.

When the washing programme has

finished, it is recommended that the

dishwasher is unplugged and the

water tap turned off.

Washing programmes

Programme Degree of soil Type of load Programme description

Intensive

Heavy soil Crockery, cutlery, pots

and pans

Prewash

Main wash up to 70°C

2 intermediate rinses

Final rinse

Drying

Auto

Any Crockery, cutlery, pots

and pans

Prewash

Main wash up to 45°C or

70°C

1 or 2 intermediate rinses

Final rinse

Drying

Quick

Normal or light soil Crockery and cutlery Main wash up to 60°C

Final rinse

Eco

Normal soil Crockery and cutlery Prewash

Main wash up to 50°C

1 intermediate rinse

Final rinse

Drying

16 electrolux

Programme Degree of soil Type of load Programme description

Glass

Normal or light soil Delicate crockery and

glassware

Main wash up to 45°C

1 intermediate rinse

Final rinse

Drying

1) During the Auto programme, the soil level of the dishes is given by how cloudy the water is. The

programme duration and consumptions can change. This depends if the appliance is fully or not and

on the level of soil on the dishes. The appliance adjusts automatically the temperature of the water

during the main wash.

2) This is the perfect daily programme to clean a not fully load. Ideal for a family of 4 persons who only

want to load breakfast and dinner crockery and cutlery.

3) Test programme for test institutes

Consumption values

Programme Duration (in mi-

nutes)

Energy (in kWh) Water (in litres)

Intensive - 1,6 - 1,8 19 - 21

Auto - 0,8 - 1,3 10 - 19

Quick - 0,8 8

Eco - 0,8 - 0,9 12 - 13

Glass - 0,6 - 0,7 11 - 12

1) The digital display shows the programme duration.

The pressure and temperature of the

water, the variations of power supply

and the quantity of dishes can change

these values.

Care and cleaning

Cleaning the filters

The filters must be checked and cleaned

from time to time. Dirty filters will degrade the

washing result.

Warning! Before cleaning the filters

ensure that the machine is switched off.

1. Open the door, remove the lower basket.

2. The dishwasher filter system comprises a

coarse filter ( A ), a microfilter ( B ) and a

flat filter. Unlock the filter system using the

handle on the microfilter.

3. Turn the handle about 1/4 a turn anti-

clockwise and remove the filter system

4. Take hold of the coarse filter ( A ) by the

handle with the hole and remove from the

microfilter ( B ).

5. Clean all filters thoroughly under running

water.

6. Remove the flat filter from the base of the

washing compartment and clean both

faces thoroughly.

electrolux 17

7. Put the flat filter back in the base of the

washing compartment and ensure that it

fits perfectly.

8. Place the coarse filter ( A ) in the microfil-

ter ( B ) and press together.

9. Put the filter combination in place and

lock by turning the handle clockwise to

the stop. During this process ensure that

the flat filter does not protrude above the

base of the washing compartment.

NEVER use the dishwasher without

filters. Incorrect repositioning and

fitting of the filters will produce poor

washing results and will result in

damage to the appliance.

NEVER try to remove the spray

arms.

If residues of soil have clogged the holes

in the spray arms, remove the debris

with a cocktail stick.

External cleaning

Clean the external surfaces of the machine

and control panel with a damp soft cloth. If

necessary use only neutral detergents. Never

use abrasive products, scouring pads or sol-

vent (acetone, trichloroethylene etc...).

Internal cleaning

Ensure that the seals around the door, the

detergent and rinse aid dispensers are

cleaned regularly with a damp cloth.

We recommend every 3 months you run the

wash programme for heavy soiled dishes us-

ing detergent but without dishes.

Prolonged periods of non-operation

If you are not using the machine for a pro-

longed period of time you are advised to:

1. Unplug the appliance and then turn off

the water.

2. Leave the door ajar to prevent the forma-

tion of any unpleasant smells.

3. Leave the inside of the machine clean.

Frost precautions

Avoid placing the machine in a location

where the temperature is below 0°C. If this is

unavoidable, empty the machine, close the

appliance door, disconnect the water inlet

pipe and empty it.

Moving the machine

If you have to move the machine (moving

house etc...):

1. Unplug it.

2. Turn the water tap off.

3. Remove the water inlet and discharge

hoses.

4. Pull the machine out together with the

hoses.

Avoid over tilting the machine during trans-

portation.

What to do if…

The dishwasher will not start or stops during

operation.

Certain problems can be due to the lack of

simple maintenance or oversights, which can

be solved with the help of the hints described

in the chart, without calling out an engineer.

Switch off the dishwasher, open the door

and carry out the following suggested cor-

rective actions.

18 electrolux

Fault codes and malfunction Possible cause and solution

• continuous flashing of the light of the running

programme

•

digital display shows

The dishwasher does not fill with water

• The water tap is blocked or furred with lime-

scale.

Clean the water tap.

• The water tap is turned off.

Turn the water tap on.

• The filter (where present) in the water inlet hose

is blocked.

Clean the filter in the water inlet hose.

• The water inlet hose has not been correctly laid

or it is kinked or squashed.

Check the water inlet hose connection.

• continuous flashing of the light of the running

programme

•

digital display shows

The dishwasher will not drain

• The sink spigot is blocked.

Clean out the sink spigot.

• The water drain hose has not been correctly laid

or it is kinked or squashed.

Check the water drain hose connection.

• continuous flashing of the light of the running

programme

•

digital display shows

Anti-flood device is activated

• Close the water tap and contact your local

Service Force Centre.

Malfunction Possible cause and solution

The programme does not start • The dishwasher door has not been properly

closed.

Close the door.

• The main plug is not plugged in.

Insert the main plug

• The fuse has blown out in the household fuse

box.

Replace the fuse.

• Delay start has been set.

If dishes are to be washed immediately, cancel

the delay start.

Once these checks have been carried out

switch on the appliance.

The programme will continue from the point

at which it was interrupted.

If the malfunction or fault code reappears

contact your local Service Force Centre.

For other fault codes not described in the

above chart, please contact your local Serv-

ice Force Centre.

Contact your local Service Force Centre,

quoting the model (Mod.), product number

(PNC) and serial number (S.N.).

This information can be found on the rating

plate located on the side of the dishwasher

door.

So that you always have these numbers at

hand, we recommend you to make a note of

them here:

Mod. : . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

PNC : . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

S.N. : . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

electrolux 19

The wash results are not satisfactory

The dishes are not

clean

• The wrong programme has been selected.

• The dishes are arranged in such a way as to stop water reaching all parts

of a surface. The baskets must not be overloaded.

• The spray arms do not rotate freely due to incorrect arrangement of the

load.

• The filters in the base of the washing compartment are dirty or incorrectly

positioned.

• Too little or no detergent has been used.

• Where there are limescales deposits on the dishes; the salt container is

empty or incorrect level of the water softener has been set.

• The drain hose connection is not correct.

• The salt container cap is not properly closed.

The dishes are wet

and dull

• Rinse aid was not used.

• The rinse aid dispenser is empty.

There are streaks,

milky spots or a blu-

ish coating on

glasses and dishes

• Decrease rinse aid dosage.

Water drops have

dried onto glasses

and dishes

• Increase rinse aid dosage.

• The detergent may be the cause. Contact the detergent manufacturer con-

sumer care line.

If after all these checks, the problem persists,

contact your local Service Force Centre.

Technical data

Dimensions Width

Height

Depth

45 cm

85 cm

63 cm

Electrical connection - Voltage -

Overall power - Fuse

Information on the electrical connection is given on the rating plate

on the inner edge of the dishwasher door.

Water supply pressure Minimum

Maximum

0,05 MPa (0,5 bar)

0,8 MPa (8 bar)

Capacity 9 place settings

Hints for test institutes

Testing in accordance with EN 60704 must

be carried out with appliance fully loaded and

using the test programme (refer to 'Washing

programmes').

Test in accordance with EN 50242 must be

carried out when the salt container and rinse

aid dispenser have been filled with salt and

rinse aid respectively and using the test pro-

gramme (refer to 'Washing programmes').

Full load: 9 standard place settings

Amount of detergent required: 5 g + 20 g (Type B)

Rinse aid setting position 4 (Type III)

Testing MUST be carried out with:

• NO soft spikes

• NO mini cutlery basket.

REMOVE these items from the upper

basket.

20 electrolux

Page is loading ...

Electrolux ESF46710W User manual

Brand: Electrolux

Model: ESF46710W

Category: Dishwashers

Type: User manual

This manual is also suitable for

ESF46710X

Download PDF

report

Electrolux ESF46710W User manual

This manual is also suitable for

Electrolux ESF46710W User manual

Other documents