Grizzly Industrial G0512 User manual

Brand: Grizzly Industrial

Model: G0512

Category: Power sanders

Type: User manual

This manual is also suitable for

Sander G0512

WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE

OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.

#528603624 PRINTED IN TAIWAN

ONLINE MANUAL DISCLAIMER

THE INFORMATION IN THIS MANUAL REPRESENTS THE CONFIGURATION OF THE MACHINE AS IT IS CURRENTLY BEING SHIPPED. THE MACHINE

CONFIGURATION CAN CHANGE AS PRODUCT IMPROVEMENTS ARE INCORPORATED. IF YOU OWN AN EARLIER VERSION OF THE MACHINE, THIS

MANUAL MAY NOT EXACTLY DEPICT YOUR MACHINE . CONTACT CUSTOMER SERVICE IF YOU HAVE ANY QUESTIONS ABOUT DIFFERENCES. PRE-

VIOUS VERSIONS ARE NOT AVAILABLE ONLINE.

EDGE SANDER

MODEL G0512

INSTRUCTION MANUAL

WARNING

Some dust created by power sanding, sawing, grind-

ing, drilling, and other construction activities contains

chemicals known to the State of California to cause

cancer, birth defects or other reproductive harm.

Some examples of these chemicals are:

• Lead from lead-based paints.

• Crystalline silica from bricks, cement, and

other masonry products.

• Arsenic and chromium from chemically treated

lumber.

Your risk from these exposures varies, depending on

how often you do this type of work. To reduce your

exposure to these chemicals: work in a well ventilated

area, and work with approved safety equipment, such

as those dust masks that are specially designed to fil-

ter out microscopic particles.

SECTION 1: SAFETY........................................................................................................................2

Safety Instructions For Power Tools ..........................................................................................2

Additional Safety Instructions For Sanders ................................................................................4

SECTION 2: INTRODUCTION ..........................................................................................................5

SECTION 3: CIRCUIT REQUIREMENTS ........................................................................................6

Grounding....................................................................................................................................7

Extension Cords..........................................................................................................................7

SECTION 4: IDENTIFICATION ........................................................................................................8

SECTION 5: SET UP ........................................................................................................................9

Unpacking ..................................................................................................................................9

G0512 Inventory..........................................................................................................................9

Hardware Recognition Chart ....................................................................................................10

Clean Up ..................................................................................................................................11

Site Considerations ..................................................................................................................11

Beginning Assembly..................................................................................................................12

Installing Feet............................................................................................................................12

Installing Tension Lever ............................................................................................................13

Installing Sanding Belt ..............................................................................................................13

Attaching Dust Port ..................................................................................................................14

Installing Roller Guard ..............................................................................................................15

Test Run & Tracking ................................................................................................................15

Installing Table ..........................................................................................................................16

Installing Back Stop ..................................................................................................................18

Connecting to Dust Collection System......................................................................................18

SECTION 6: OPERATIONS ............................................................................................................19

Power Switch ............................................................................................................................19

Adjusting Table Height..............................................................................................................20

Sanding Belt Selection..............................................................................................................20

Edge & End Sanding ................................................................................................................21

Contour Sanding ......................................................................................................................22

SECTION 7: MAINTENANCE ........................................................................................................23

General......................................................................................................................................23

Table ........................................................................................................................................23

Lubrication ................................................................................................................................23

Sanding Belt..............................................................................................................................23

SECTION 8: SERVICE ADJUSTMENTS ........................................................................................24

About Service............................................................................................................................24

Adjusting Tensioner ..................................................................................................................24

Resetting Tensioner Spring Tension ........................................................................................25

Parallel Belt Tracking ................................................................................................................26

Platen-to-Rollers Adjustments ..................................................................................................28

SECTION 9: REFERENCE INFO ....................................................................................................31

Aftermarket Accessories ..........................................................................................................31

Machine Data Sheet..................................................................................................................32

Parts Breakdown and List ........................................................................................................33

Troubleshooting Machine..........................................................................................................35

Troubleshooting Sanding ..........................................................................................................36

G0512 Wiring Diagram..............................................................................................................37

Warranty and Returns ..............................................................................................................38

TABLE OF CONTENTS

-2-

G0512 Edge Sander

5. KEEP CHILDREN AND VISITORS

AWAY. All children and visitors should be

kept at a safe distance from work area.

6. MAKE WORKSHOP CHILD PROOF with

padlocks, master switches, or by removing

starter keys.

7. NEVER FORCE TOOL. It will do the job

better and safer at the rate for which it was

designed.

8. USE RIGHT TOOL. DO NOT force tool or

attachment to do a job for which it was not

designed.

1. KEEP GUARDS IN PLACE and in working

order.

2. REMOVE ADJUSTING KEYS AND

WRENCHES. Form habit of checking to

see that keys and adjusting wrenches are

removed from tool before turning on.

3. KEEP WORK AREA CLEAN. Cluttered

areas and benches invite accidents.

4. NEVER USE IN DANGEROUS ENVI-

RONMENT. DO NOT use power tools in

damp or wet locations, or where any flam-

mable or noxious fumes may exist. Keep

work area well lighted.

For Your Own Safety Read Instruction

Manual Before Operating This Equipment

Indicates an imminently hazardous situation which, if not avoided,

WILL result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided,

COULD result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided,

MAY

result in minor or moderate injury. It may also be used to alert

against unsafe practices.

This symbol is used to alert the user to useful information about

proper operation of the equipment.

The purpose of safety symbols is to attract your attention to possible hazardous conditions.

This manual uses a series of symbols and signal words which are intended to convey the level

of importance of the safety messages. The progression of symbols is described below.

Remember that safety messages by themselves do not eliminate danger and are not a substi-

tute for proper accident prevention measures.

NOTICE

Safety Instructions For Power Tools

SECTION 1: SAFETY

G0512 Edge Sander -3-

9. USE PROPER EXTENSION CORD. Make

sure your extension cord is in good condi-

tion. Conductor size should be in accor-

dance with the chart below. The amperage

rating should be listed on the motor or tool

nameplate. An undersized cord will cause

a drop in line voltage resulting in loss of

power and overheating. Your extension

cord must also contain a ground wire and

plug pin. Always repair or replace exten-

sion cords if they become damaged.

Minimum Gauge for Extension Cords

10. WEAR PROPER APPAREL. DO NOT

wear loose clothing, gloves, neckties,

rings, bracelets, or other jewelry which may

get caught in moving parts. Non-slip

footwear is recommended. Wear protective

hair covering to contain long hair.

11. ALWAYS USE SAFETY GLASSES. Also

use face or dust mask if cutting operation is

dusty. Everyday eyeglasses only have impact

resistant lenses, they are NOT safety glasses.

12. SECURE WORK. Use clamps or a vise to hold

work when practical. It is safer than using your

hand and frees both hands to operate tool.

13. DO NOT OVER-REACH. Keep proper

footing and balance at all times.

14. MAINTAIN TOOLS WITH CARE. Keep

tools sharp and clean for best and safest

performance. Follow instructions for lubri-

cating and changing accessories.

LENGTH

AMP RATING 25ft 50ft 100ft

0-6 16 16 16

7-10 16 16 14

11-12 16 16 14

13-16 14 12 12

17-20 12 12 10

21-30 10 10 No

Safety Instructions For Power Tools

15. USE RECOMMENDED ACCESSORIES.

Consult the owner’s manual for recom-

mended accessories. The use of improper

accessories may cause risk of injury.

16. REDUCE THE RISK OF UNINTENTION-

AL STARTING. On machines with magnet-

ic contact starting switches there is a risk of

starting if the machine is bumped or jarred.

Always disconnect from power source

before adjusting or servicing. Make sure

switch is in OFF position before reconnecting.

17. CHECK DAMAGED PARTS. Before fur-

ther use of the tool, a guard or other part

that is damaged should be carefully

checked to determine that it will operate

properly and perform its intended function.

Check for alignment of moving parts, bind-

ing of moving parts, breakage of parts,

mounting, and any other conditions that

may affect its operation. A guard or other

part that is damaged should be properly

repaired or replaced.

18. NEVER LEAVE TOOL RUNNING UNAT-

TENDED. TURN POWER OFF. DO NOT

leave tool until it comes to a complete stop.

19. NEVER OPERATE A MACHINE WHEN

TIRED, OR UNDER THE INFLUENCE OF

DRUGS OR ALCOHOL. Full mental alert-

ness is required at all times when running a

machine.

20. NEVER ALLOW UNSUPERVISED OR

UNTRAINED PERSONNEL TO OPER-

ATE THE MACHINE. Make sure any

instructions you give in regards to machine

operation are approved, correct, safe, and

clearly understood.

21. IF AT ANY TIME YOU ARE EXPERIENC-

ING DIFFICULTIES performing the intend-

ed operation, stop using the machine! Then

contact our service department or ask a

qualified expert how the operation should

be performed.

-4-

G0512 Edge Sander

Like all power tools, there is danger asso-

ciated with the Edge Sander. Accidents are

frequently caused by lack of familiarity or

failure to pay attention. Use this tool with

respect and caution to lessen the possibil-

ity of operator injury. If normal safety pre-

cautions are overlooked or ignored, seri-

ous personal injury may occur.

No list of safety guidelines can be complete.

Every shop environment is different. Always

consider safety first, as it applies to your

individual working conditions. Use this and

other machinery with caution and respect.

Failure to do so could result in serious per-

sonal injury, damage to equipment or poor

work results.

Additional Safety Instructions For Sanders

• DO NOT allow anyone to stand near the

sander while sanding wood stock.

• DO NOT jam the workpiece against the

sanding belt. Firmly grasp the workpiece in

both hands and ease it against the sanding

belt, using light pressure.

• DO NOT wear loose clothing while operat-

ing this machine. Roll up or button sleeves

at the cuff.

• DO NOT place hands near, or in contact

with, sanding belt during operation.

• ANY PROBLEM, with the exception of belt

tracking, that is concerned at all with any

moving parts or accessories must be

investigated and corrected with the power

disconnected, and after everything has

come to a complete stop.

•

PERFORM machine inspections and main-

tenance service promptly when called for.

• NEVER leave the machine running unat-

tended.

• REPLACE sanding belt when it becomes

worn.

• NEVER sand more than one piece of stock

at a time.

• ALWAYS inspect board stock for nails,

staples, knots, and other imperfections that

could be dislodged and thrown from the

machine during sanding operations.

• NEVER operate the sander without an

adequate dust collection system in place

and running.

• NEVER sand tapered or pointed stock with

the point facing the feed direction.

•ALWAYSwear a dust mask when sand-

ing. Using this machine produces sawdust

which may cause allergic reactions or res-

piratory problems.

G0512 Edge Sander -5-

We are proud to offer the Model G0512 Edge

Sander. This Edge Sander is part of a growing

Grizzly family of fine woodworking machinery.

When used according to the guidelines set forth

in this manual, you can expect years of trouble-

free, enjoyable operation and proof of Grizzly’s

commitment to customer satisfaction.

This sander was developed for those projects

that require a large support area and need the

workpiece to be moved around the roller. The

specially designed small 2

⁄2" edge diameter

roller allows you to get into tighter radius projects

like guitar bodies, curved chair legs etc.... The

table is supported in four positions to eliminate

sagging and to provide a stable base while

working, and the quick belt release mechanism

makes it easy to change belts fast.

We are pleased to provide this manual with the

Model G0512. It was written to guide you through

assembly, to review safety considerations, and to

cover general operating procedures. It repre-

sents our effort to produce the best documenta-

tion possible.

If you have any comments regarding this manual,

please write to us at the address below:

Grizzly Industrial, Inc.

/O Technical Documentation

P.O. Box 2069

Bellingham, WA 98227-2069

Most importantly, we stand behind our machines.

If you have any service questions or parts

requests, please call or write us at the location

listed below.

Grizzly Industrial, Inc.

1203 Lycoming Mall Circle

Muncy, PA 17756

Phone: (570) 546-9663

Fax: (800) 438-5901

E-Mail: [email protected]

Web Site: http://www.grizzly.com

The specifications, drawings, and photographs

illustrated in this manual represent the Model

G0512 as supplied when the manual was pre-

pared. However, owing to Grizzly’s policy of con-

tinuous improvement, changes may be made at

any time with no obligation on the part of Grizzly.

For your convenience, we always keep current

Grizzly manuals available on our website at

www.grizzly.com

. Any updates to your machine

will be reflected in these manuals as soon as they

are complete. Visit our site often to check for the

latest updates to this manual!

SECTION 2: INTRODUCTION

Read the manual before

assembly and operation.

Serious personal injury

may result if safety or

operational information

is not understood or fol-

lowed.

-6-

G0512 Edge Sander

SECTION 3: CIRCUIT REQUIREMENTS

Amperage Draw

The Model G0512 features a 110V/220V motor

that is prewired at 220V.

Motor Load at 220V ..............................10 amps

Motor Load at 110V ..............................20 amps

Plug Type

The cord set enclosed does not have a plug as

the style of plug you require will depend upon the

type of service you currently have or plan to

install. We recommend using the following plugs

for your machine on a dedicated circuit only (see

Figures 1 & 2 for an example):

220V Plug & Receptacle..............................6-15

110V Plug & Receptacle..............................5-20

Circuit Breaker Requirements

Please use the following guidelines when choos-

ing a circuit breaker for your machine (circuit

breakers rated any higher are not adequate to

protect the circuit):

220V Circuit Breaker ..............................10 amp

110V Circuit Breaker ..............................20 amp

Your Circuit Capacity

Always check to see if the wires in your circuit are

capable of handling the amperage load from your

machine. If you are unsure, consult a qualified

electrician. If you operate your sander on any cir-

cuit that is already close to its capacity, it might

blow a fuse or trip a circuit breaker. However, if

an unusual load does not exist and a power fail-

ure still occurs, contact a qualified electrician or

our Service Department.

Figure 1. 6-15 plug and receptacle.

Figure 2. 5-20 plug and outlet.

DO NOT connect your machine to the power

source until you have completed the assem-

bly process and have been instructed to do

so in this manual. Otherwise, serious per-

sonal injury could occur.

NOTICE

The Model G0512 is prewired for 220V oper-

ation. If you plan to rewire your machine for

110V, you must use a different switch.

Consult a licensed electrician before

attempting to rewire your machine!

G0512 Edge Sander -7-

In the event of an electrical short, grounding

reduces the risk of electric shock by providing a

path of least resistance to disperse electric cur-

rent. This tool is equipped with a power cord that

has a plug with an equipment-grounding prong.

The outlet must be properly installed and ground-

ed in accordance with all local codes and ordi-

nances.

This machine must have a ground prong in

the plug to help ensure that it is grounded.

DO NOT remove ground prong from plug to

fit into a two-pronged outlet! If the plug will

not fit the outlet, have the proper outlet

installed by a qualified electrician.

Electrocution or fire could

result if this machine is

not grounded correctly.

Make sure all electrical

circuits are grounded

before you connect them

to the machine. DO NOT

use this machine if it is

not grounded.

220V Operation

We do not recommend the use of extension cords

on 220V equipment. Instead, arrange the place-

ment of your equipment and the installed wiring to

eliminate the need for extension cords.

If you find it absolutely necessary to use an

extension cord at 220V with your Grizzly Edge

Sander:

• Make sure the cord is rated for Standard

Service (grade S) or better.

• The extension cord must also contain a

ground wire and plug prong.

• Use at least a 16 gauge cord if the cord is 50

feet long or less.

• Use at least a 14 gauge cord if the cord is

between 51-100 feet.

110V Operation

If you find it necessary to use an extension cord

at 110V with your Grizzly Edge Sander:

• Make sure the cord is rated Standard Service

(grade S) or better.

• The extension cord must also contain a

ground wire and plug pin.

• Use at least a 10 gauge cord if the cord is 50

feet long or less.

• DO NOT use a cord longer that 50 feet!

Extension CordsGrounding

-8-

G0512 Edge Sander

Figure 3. The following is a list of controls and components on the Model G0512. Please take time to

become familiar with each item and its location. These items will be used throughout the manual and know-

ing them is essential to understanding the instructions and terminology used in this manual.

1. Belt Tracking Knob

2. Tracking Lock

3. Contour Sanding Area

4. Sanding Table

5. Table Elevation Handwheel

6. Lead Screw Lock Handle

7. ON/OFF Switch

8. Back Stop

9. Dust Port

10. Flat Sanding Area

11. Belt Tension Lever

SECTION 4: IDENTIFICATION

G0512 Edge Sander -9-

The Model G0512 was carefully packed when it

left our warehouse. If you discover the machine is

damaged after you have signed for delivery,

please immediately call Customer Service at

(570) 546-9663 for advice.

Save the containers and all packing materials for

possible inspection by the carrier or its agent.

Otherwise, filing a freight claim can be difficult.

When you are completely satisfied with the con-

dition of your shipment, you should inventory the

contents.

Some metal parts may

have sharp edges on

them after they are

formed. Please examine

the edges of all metal

parts before handling

them. Failure to do so

could result in injury.

• G0512 Sander Unit ....................................1

• Wood Table ................................................1

• Dust Port ....................................................1

• Lead Screw Bracket Assembly ..................1

• L Support ....................................................2

• Front L Support Assembly ..........................1

• Back Stop....................................................1

• Lever Handle ..............................................1

• 6" x 80" Sanding Belt ..................................1

• Idler Roller Cover ........................................1

• Small Star Knob ..........................................1

• Hardware Bag ............................................1

—Lock Handle ............................................3

—Flat Washer

⁄8"........................................6

—Plastic Feet..............................................4

—Phillips Head Screw #10-24 x

⁄8"............4

—Phillips Head Tap Screws #8 x

⁄4" ........19

The Edge Sander is a

heavy machine at

approx. 250 lbs. ship-

ping weight. DO NOT

move the machine by

yourself – you will need

assistance or power

equipment. Serious per-

sonal injury may occur if

safe moving methods

are not followed.

Figure 4. Model G0512 packaging inventory.

G0512 InventoryUnpacking

SECTION 5: SET UP

-10- G0512 Edge Sander

Hardware Recognition Chart

G0512 Edge Sander -11-

Floor Load

The Model G0512 weighs 235 lbs. and has a

⁄2" x 32" footprint on the bottom of the stand.

Most commercial floors are suitable for your

machine. Some residential floors may require

additional build up to support both the machine

and operator.

Working Clearances

Consider existing and anticipated needs, size of

material to be processed through each machine,

and space for auxiliary stands, work tables or

other machinery when establishing a location for

your bandsaw.

Lighting and Outlets

Lighting should be bright enough to eliminate

shadow and prevent eye strain. Electrical circuits

should be dedicated or large enough to handle

amperage requirements. Outlets should be locat-

ed near each machine so power or extension

cords are clear of high-traffic areas. Observe

local electrical codes for proper installation of

new lighting, outlets, or circuits.

The unpainted surfaces are coated with a waxy

oil to protect them from corrosion during ship-

ment. Remove this protective coating with a sol-

vent cleaner or citrus-based degreaser such as

Grizzly’s G7895 Degreaser. To clean thoroughly,

some parts may need to be removed. For opti-

mum performance from your machine, make

sure you clean all moving parts or sliding

contact surfaces that are coated. Avoid chlo-

rine-based solvents as they may damage painted

surfaces should they come in contact.

Do not use gasoline or

other petroleum-based

solvents to clean with.

They have low flash

points which make them

extremely flammable. A

risk of explosion and

burning exists if these

products are used.

Do not smoke while using

solvents. A risk of explo-

sion or fire exists and may

result in serious personal

injury.

Site ConsiderationsClean Up

Many of the solvents

commonly used to clean

machinery can be toxic

when inhaled or ingest-

ed. Lack of ventilation

while using these sol-

vents could cause seri-

ous personal health risks

or fire. Take precautions

from this hazard by only

using cleaning solvents

in a well ventilated area.

Unsupervised children and

visitors inside your shop

could cause serious person-

al injury to themselves. Lock

all entrances to the shop

when you are away and DO

NOT allow unsupervised

children or visitors in your

shop at any time!

-12-

G0512 Edge Sander

This section will cover the minimum assembly

and adjustment instructions needed to begin

operation. For best results, complete the assem-

bly in the order provided in this manual and then

read the remaining portion of the manual before

attempting any type of operations.

Safety must come first! Read and follow these

instructions before beginning assembly:

Most of your Edge Sander has been assembled

at the factory, but some parts must be assembled

or installed after delivery.

Some metal parts may

have sharp edges on

them after they are

formed. Please examine

the edges of all metal

parts before handling

them. Failure to do so

could result in injury.

Disconnect power to the

machine when perform-

ing all assembly steps.

Failure to do this may

result in serious person-

al injury.

Wear safety glasses dur-

ing the entire assembly

process. Failure to com-

ply may result in serious

personal injury.

To install the feet on the sander:

1. Thread the feet into the bottom of the stand

as shown in Figure 5.

Figure 5. Stand foot threaded onto stand.

Installing FeetBeginning Assembly

Stand Foot

G0512 Edge Sander -13-

To install the sanding belt:

1. Make sure the tension lock knob is loosened.

2. Move the tension lever into the release posi-

tion as shown in Figure 7.

Figure 7. Tension lever in release position.

Figure 8. Installing sanding belt.

3. Make sure the arrows on the inside of the

belt point in the counter-clockwise direction,

and place the sanding belt over both rollers

as shown in Figure 8.

To install the tension lever:

1. Thread the end of the tension lever into the

swivel assembly as shown in Figure 6.

Figure 6. Installing tension lever in swivel

assembly.

2. Tighten the lock nut against the swivel

assembly to secure the tension lever.

Installing Sanding

Belt

Installing Tension

Lever

Swivel

Assembly

Tension

Lever

Lock

Nut

Notice Arrow

Direction on

Belt

Tension

Lock Knob

-14-

G0512 Edge Sander

Figure 9. Dust port attached to brackets.

To attach the dust port:

1. Attach the dust port to the support brackets

with the three

⁄16"-18 x

⁄2" hex bolts and

washers, as shown in Figure 9, but DO NOT

completely tighten the bolts yet.

2. Position the dust port approximately

⁄2" away

from the driver roller and tighten the two

attachment bolts from step 1.

The voltage you decide to use with your sander

will determine which plug and receptacle you

install. Read pages 6 & 7, in Section 3: Circuit

Requirements for more information.

Install the plug and receptacle now.

Connecting Plug to

Cord

Attaching Dust Port

G0512 Edge Sander -15-

Figure 11. Sanding belt even with

top of main roller.

Figure 10. Idler roller guard installed and

secured in position with small star knob.

Before you can install the table, you must run the

sander to track the belt. However, you should

perform a “pre-tracking” procedure before starting

the sander to ensure that the belt does not come

off of or bottom out on the rollers during the initial

startup.

To pretrack the belt:

1. Make sure that the sander is disconnect-

ed from the power!

2. Loosen the tracking lock knob.

3. Standing in front of the sander, push the

sanding belt multiple times along the platen,

so that it moves in the direction of operation

(counter-clockwise on the rollers), and watch

how the belt tracks on the rollers.

4. Adjust the tracking higher or lower as need-

ed and continue to rotate the belt by hand.

5. Repeat steps 3 & 4 until the top of the sand-

ing belt rides even with the top of the main

roller as shown in Figure 11.

To install the roller guard:

1. Place the guard on top of the idler roller and

secure it in position with the included small

star knob, as shown in Figure 10.

Test Run & TrackingInstalling Roller

Guard

-16-

G0512 Edge Sander

Installing Table

To test run and track the belt:

1. Make sure the belt is properly pre-tracked as

described previously.

2. Tie back loose clothing and long hair to pro-

tect yourself from getting caught in the mov-

ing sanding belt when you start the machine.

3. Make sure the switch is in the down position

(OFF), then connect the sander to the power

source.

Use extreme caution when preparing for

your initial test run. Always keep one finger

on the switch in order to quickly STOP the

machine in the event of a malfunction or

incorrect belt tracking.

4. Start the sander; it should run smoothly with

little or no vibration or rubbing noises.

Strange or unnatural noises should be inves-

tigated and corrected before further opera-

tion.

— If noises occur that can not be found by

visual inspection, feel free to contact our

Service Department for help.

5. Using the tracking control knob, carefully

adjust the tracking higher or lower until the

top of the sanding belt remains even with the

top of the main roller. Note—The tracking

control knob is very sensitive, adjust it with

caution.

6. When the tracking appears to be correct,

allow the sander to run for approximately one

minute to verify that the tracking stays in the

correct position.

— If the tracking does not stay correct,

repeat steps 5 & 6.

7. When the sanding belt is tracking correctly,

tighten the tracking lock knob.

Before installing the table, the sanding belt must

be tracking correctly to ensure that the idler roller

is close to the position that it will be in during

operation.

To install the table:

1. Disconnect the sander from the power

source!

2. Insert the lead screw assembly as shown in

Figure 12.

Figure 12. Lead screw assembly installed in

bracket.

Figure 13. Table brackets laid out for

identification.

3. Identify the three table brackets in Figure 13

before continuing.

Front

Rear

G0512 Edge Sander -17-

Figure 14. Front L support installed.

Figure 16. Allen wrench placed between platen

and table.

Figure 17. Three places to ensure the spacing

between the sanding belt and the table is even.

4. Install the front L support with the lock han-

dle and two

⁄8" flat washers as shown in

Figure 14.

5. Install the L supports with the lock handles

and remaining four

⁄8" flat washers as shown

in Figure 15. The smallest L support at the

rear of the machine should be closest to the

motor.

6. Lower the lead screw support all the way

down and adjust all of the L support brackets

up to approximately the same height. This

will prepare the brackets for the table place-

ment.

7. Place the table on the supports.

8. Use a 3mm or

⁄8" Allen wrench as a gauge to

position the table evenly away from the plat-

en and the idler roller. Do this by placing the

Allen wrench as shown in Figure 16, at the

three locations shown in Figure 17.

9. Clamp the table to the supports or have an

assistant hold the table in place, and secure

the table to the supports with the #8 x

⁄4"

Phillips head tap screws provided in the

hardware bag.

Figure 15. Rear L supports installed.

-18-

G0512 Edge Sander

To install the back stop:

1. Use a machinists square to position the back

stop perpendicular to the platen, on the end

of the table that is near the ON/OFF switch.

2. Secure the backstop to the table with three

#8 x

⁄4" Phillips head tap screws (as shown

in Figure 18).

Figure 18. Back stop mounted on table.

The dust port can be connected to a dust collec-

tion system with a 4" hose. However, in order to

move the dust from the sander, the dust collec-

tion system must be able to move approximately

500 CFM where the hose connects to the dust

port. Note—This number is an approximation and

is used for estimation purposes only.

To connect the dust port to a dust collection

system:

1. Slide the 4" hose completely over the dust

port as shown in Figure 19.

Figure 20. Dust port connected to dust

collection system.

2. Tighten the hose clamp to ensure a snug,

sealed fit.

Connecting to Dust

Collection System

Installing Back Stop

Back

Stop

Page is loading ...

Grizzly Industrial G0512 User manual

Brand: Grizzly Industrial

Model: G0512

Category: Power sanders

Type: User manual

This manual is also suitable for

Sander G0512

Download PDF

report

Grizzly Industrial G0512 User manual

This manual is also suitable for

Grizzly Industrial G0512 User manual

Related papers

Other documents