Faure AFT602W User manual

Brand: Faure

Model: AFT602W

Category: Cooker hoods

Type: User manual

This manual is also suitable for

INSTRUCTIONS FOR INSTALLATION AND USE

MONTAGE- UND GEBRAUCHSANWEISUNG

INSTRUCTIONS POUR L'INSTALLATION ET L’UTILISATION

ISTRUZIONI PER L'INSTALLAZIONE E L’USO

INSTRUCCIONES PARA INSTALACIÓN Y USO

INSTRUÇÕES DE INSTALAÇÃO Y UTILIZAÇÃO

AANWIJZING VOOR GEBRUIK EN INSTALLATIE

ENGLISH

DESCRIPTION

The hood may be installed in the filtering or the ducting version.

Filtering version (Fig. 1): The hood aspirates the kitchen air saturated with fumes and odours, purifies it

through the grease filters and charcoal filters and returns clean air into the room. For constant efficiency, the

charcoal filters must be replaced periodically.

Ducting version (Fig. 2): The hood aspirates the kitchen air saturated with fumes and odours, passes it through

the grease filters and expels it to the outside through an outlet pipe. With this version the charcoal filters are

not required.

Decide from the outset on the type of installation (filtering or ducting). For greater efficiency, we recommend

you install the hood in the ducting version (if possible).

INSTALLATION

Before beginning installation, to better handle the hood, we advise removing the metal grid or the metal filter/s

(depending on the model purchased by you).

To remove the metal grid (Fig. 3), push the two stops towards the inside of the hood and turn the grid until this

can be removed.

To remove the metal filter/s (Fig. 4A or 4B), in line with the handle, push the stop inwards and pull the filter down.

INSTALLATION IN DUCTING VERSION:

Before fixing, the outlet pipe for air evacuation to the outside must be installed. Use an outlet pipe with:

- minimum indispensable length; - Minimum possible bends (maximum angle of bend:90°); - certified material

(according to the State); - an as smooth as possible inside. It is also advisable to avoid any drastic changes

in pipe cross-section (recommended diameter: 125 mm). For air evacuation to the outside, follow all the instructions

given on the “Warnings” sheet.

Decide on the position of the hole for the air outlet: The hole may be in the wall or the ceiling, according

to your requirements, but must be in vertical line with your hob. Bear in mind that the hood can expel air through

the rear opening A (Fig. 5) or through the top opening B.

Select the type of configuration most suited to your needs and proceed by mounting the flange C (Fig. 6)

on the opening selected for air evacuation (A or B): make the 3 flange clips and the catch D coincide with the

slots on the hood; slightly turn the flange clockwise until it locks. Close the other opening by mounting the “cap”

(E) in the same way: Make the 3 cap clips and the catch F coincide with the slots on the hood; slightly turn

the cap clockwise until it locks.

Drill the hole in the wall for the air outlet (133 mm diameter) referring to Fig. 7 where the measurements for

the various possibilities are indicated.

Prepare a suitable power supply. For the electrical connection, follow all the other instructions on the “Warnings”

sheet.

Proceed with fixing the hood: Based on your requirements, you can fit the hood on the wall or on a wall

unit of your kitchen. IMPORTANT: Respect the distance between the hob and lower part of the hood which must

be at least 650 cm.

Fixing to the wall: If you use the top opening B for the air outlet through the wall unit, before fixing the

hood to the wall, drill a hole of 133 mm diameter in the wall unit (Fig. 8). In any case, check the position of

the power outlet and consider where the power cable will run, since a hole might have to be made in the wall

unit to accommodate it. Draw a line on the wall in vertical line with your hob. Mark the 4 holes to be drilled

in the wall, respecting the distances indicated in Fig. 9; Make the 4 holes and fit the 4 screw anchors provided.

Take 2 of the screws provided (Fig. 10G) and insert them in the topmost screw anchors without however screwing

them down completely. Hang the hood on the 2 screws; Working from inside the hood, tighten the 2 screws

completely. Now proceed with final fixing by fitting the other 2 screws H (Fig. 11). Connect a flexible tube to the

hood flange, using a metal hose clamp. Tube and hose clamps are not provided. Make the electrical connection.

Fitting under wall unit: If you use the top opening B for the air outlet through the wall unit, before fixing

the hood to the unit, drill a hole of 133 mm diameter in the wall unit (Fig. 8). In any case, check the position

of the power outlet and consider where the power cable will run, since a hole might have to be made in the wall

unit to accommodate it. Drill 4 holes in the wall unit, respecting the distances indicated in Fig. 12. Push the hood

up against the wall unit and insert the 4 screws operating from inside the wall unit (the 4 screws are not provided).

Connect a flexible tube to the hood flange, using a metal hose clamp. Tube and hose clamps are not provided.

Make the electrical connection.

Installation is now complete. We recommend you:

• CHECK THAT THE DUCTING-FILTERING LEVER IS IN THE RIGHT POSITION: The lever is found on the motor

unit and must be positioned on the symbol (P) in the case of installation in ducting version (Fig. 13).

• also remember that the use of charcoal filter/s is not necessary with the ducting version; if these are fitted,

remove them and proceed as following according to the model type purchased:

- if the hood features round charcoal filters (Fig. 14R), remove the charcoal filter by turning it clockwise.

- if the hood features a panel type charcoal filter (Fig. 15A or 16A or 17A), remove the charcoal filter by first

of all removing the two filter retainers M.

INSTALLATION IN FILTERING VERSION:

Prepare a suitable power supply. For the electrical connection, follow all the other instructions on the “Warnings”

sheet.

The 2 openings (A and B) on the hood (Fig. 5) must not be closed, since the air is recirculated into the

room through the front vents.

Proceed with fixing the hood: Based on your requirements, you can fit the hood on the wall or on a wall

unit of your kitchen. IMPORTANT: Respect the distance between the hob and lower part of the hood which must

be at least 650 cm.

Fixing to the wall: Before fixing the hood to the wall, check the position of the power outlet and consider

where the power cable will run, since a hole might have to be made in the wall unit to accommodate it. Draw

a line on the wall in vertical line with your hob. Mark the 4 holes to be drilled in the wall, respecting the distances

indicated in Fig.9; Make the 4 holes and fit the 4 screw anchors provided. Take 2 of the screws provided (Fig.

10G) and insert them in the topmost screw anchors without however screwing them down completely. Hang the

hood on the 2 screws; Working from inside the hood, tighten the 2 screws completely. Now proceed with final

fixing by fitting the other 2 screws H (Fig. 11). Make the electrical connection.

Fitting under wall unit: Before fixing the hood to the wall unit, check the position of the power outlet and

consider where the power cable will run, since a hole might have to be made in the wall unit to accommodate

it. Drill 4 holes in the wall unit, respecting the distances indicated in Fig. 12. Push the hood up against the wall

unit and insert the 4 screws operating from inside the wall unit (the 4 screws are not provided). Make the electrical

connection.

Installation is now complete. We recommend you:

• CHECK THAT THE DUCTING-FILTERING LEVER IS IN THE RIGHT POSITION: The lever is found on the motor

unit and must be positioned on the symbol (Q) in the case of installation in filtering version (Fig. 13).

• also remember that charcoal filter/s must be used in the case of the filtering version; check to see whether

such filters are already fitted; if necessary, proceed to fit as follows, depending on the model type purchased:

- if the hood features round charcoal filters (Fig. 18R), fit the charcoal filter by turning anti-clockwise.

- if the hood features a panel type charcoal filter/s (Fig. 15A or 17A), position the charcoal filter inside and fit

the two filter retainers to secure the charcoal filter.

OPERATION

Depending on the model, the unit is equipped with the following controls:

Controls as in Fig. 19: A = Light switch. B = Motor ON/OFF switch - speed I C = switch - speed II D

= switch - speed III E = Motor on light.

Controls as in Fig. 20: A = Light switch; position 0: light off; position 1: light on. B = Motor switch; position

0: motor off; position 1-2-3: Motor on at speed I, II and II. C = Motor on light.

Grease filter/s: Depending on the version, the hood features different types of grease filters:

Modular metal filter/s (of the type shown in Fig. 21 or 22): these are metal filters and must be periodically cleaned,

depending on extent of operation (at least every two months). Wash the filters with neutral detergent. To remove

the filters, in line with the handle, push the stop inwards and pull the filter down (Fig. 4A or 4B).

Panel type metal filter (as shown in Fig. 23N): this is a metal filter and is positioned inside the metal grid; the

filter must be periodically cleaned, depending on extent of operation (at least every two months). Wash the filter

with neutral detergent. To remove the filter, first of all remove the metal grid by pushing the two stops towards

the inside of the hood (Fig. 3); subsequently remove the two filter retainers inside the metal grid and remove the

panel type metal filter.

Panel type synthetic filter (as shown in Fig. 24P): this filter is made of white synthetic fibres and is located

inside the metal grid; it cannot be cleaned, but must be replaced from time to time according to use (at least

every two months). To remove the filter, first of all remove the metal grid, push the two stops towards the inside

of the hood (Fig. 3); next, remove the two filter retainers inside the metal grid and remove the panel type synthetic

filter.

Charcoal filter/s: the charcoal filters must be periodically replaced depending on extent of operation - on

average every 6 months. To remove the charcoal filters, proceed as follows, depending on the model purchased:

- if the hood features round charcoal filters (Fig. 14R), remove the charcoal filter by turning clockwise.

- if the hood features a panel type charcoal filter (Fig. 16A or 17A), remove the charcoal filter by first of all removing

the two filter retainers M.

Lighting:

To access the incandescent lamps, remove the metal grid or metal filter/s (depending on the model you have

purchased): to remove the metal grid (Fig. 3), push the two stops towards the inside of the hood and turn the

grid until this can be removed. To remove the metal filter/s (Fig. 4A or 4B), in line with the handle, push the stop

inwards and pull the filter down. Replace with lamps of the same kind (Fig. 25).

Warning: If you have a hood in the version with 2 motors, to take out the bulbs remove the glass light fitting

Page is loading ...

Wiring Diagram (1 MOTOR) - Elektrischer Schaltplan (1 MOTOR) -

Schéma Électrique (1 MOTEUR) - Schema Elettrico (1 MOTORE) -

Esquema Eléctrico (1 MOTOR) - Esquema Eléctrico (1 MOTOR) -

Elektrisch Schema (1 MOTOR)

HOOD WITH SLIDE CONTROLS - GERÄT MIT SCHIEBEKNOPF-BEDIENUNG -

HOTTE AVEC COMMANDES A CHARIOT - CAPPA CON COMANDI A SLITTA -

CAMPANA CON MANDOS DESLIZANTES - EXAUSTOR COM COMANDOS DESLIZANTES -

AFZUIGKAP MET SCHUIFKNOPBEDIENING

HOOD WITH BUTTON CONTROLS - GERÄT MIT TASTENBEDIENUNG

HOTTE AVEC COMMANDES A BOUTONS - CAPPA CON COMANDI A PULSANTI

CAMPANA CON PULSANTES - EXAUSTOR COM COMANDOS DE BOTÕES

AFZUIGKAP MET DRUKKNOPBEDIENING

Wiring Diagram (2 MOTORS) - Elektrischer Schaltplan (2 MOTOREN) -

Schéma Électrique (2 MOTEURS) - Schema Elettrico (2 MOTORI) -

Esquema Eléctrico (2 MOTORES) - Esquema Eléctrico (2 MOTORES) -

Elektrisch Schema (2 MOTOREN)

HOOD WITH SLIDE CONTROLS - GERÄT MIT SCHIEBEKNOPF-BEDIENUNG -

HOTTE AVEC COMMANDES A CHARIOT - CAPPA CON COMANDI A SLITTA -

CAMPANA CON MANDOS DESLIZANTES - EXAUSTOR COM COMANDOS DESLIZANTES -

AFZUIGKAP MET SCHUIFKNOPBEDIENING

HOOD WITH BUTTON CONTROLS - GERÄT MIT TASTENBEDIENUNG

HOTTE AVEC COMMANDES A BOUTONS - CAPPA CON COMANDI A PULSANTI

CAMPANA CON PULSANTES - EXAUSTOR COM COMANDOS DE BOTÕES

AFZUIGKAP MET DRUKKNOPBEDIENING

Page is loading ...

ENGLISH

WARNING

The distance between the supporting surface for the cooking

vessels on the hob and the lower part of the hood must be at

least 65 cm. If the instructions for installation for the hob

specify a greater distance, this has to be taken into account.

The air collected must not be conveyed into a duct used to

blow off smokes from appliances fed with an energy other

than electricity (central heating systems, thermosiphons,

water-heaters, etc.).

Comply with the official instructions provided by the competent

authorities in merit when installing the disposal duct. In

addition, exhaust air should not be discharged into a wall

cavity, unless the cavity is designed for that purpose.

The room must be well aerated in case a hood and some

other heat equipment fed with an energy other than electricity

(gas, oil, coal heaters, etc) operate at the same time.

In fact the intake hood, disposing of air, could create a

vacuum in the room. The vacuum should not exceed 0,04mbar.

This prevents the gas exhausted by the heat source from

being intaken again. It is therefore advisable to ensure the

room contains air taps able to ensure a steady flow of fresh

air.

Check the data label inside the appliance; if the symbol

( ) is printed, read the following: this appliance has

such technical particulars that it belongs to class II

insulation, therefore it must not be earthed.

The following warning is valid in the United Kingdom only: in

case your cable is not furnished with a plug, read the following

instructions; as the colours of the wires in the mains lead of

this appliance may not correspond with the coloured markings

identifying the terminals in your plug, proceed as follows: –

the wire which is coloured blue must be connected to the

terminal which is marked with the letter N or coloured black;

– the wire which is coloured brown must be connected to the

terminal which is marked with the letter L or coloured red. –

terminal of a three-pin plug.

Check the data label inside the appliance; if the symbol

(

) is NOT printed, read the following: ATTENTION:

This appliance must be earthed. When making the electrical

connections, check that the current socket has a ground

connection.

The following warning is valid in the United Kingdom only: in

case your cable is not furnished with a plug, read the following

instructions; as the colours of the wires in the mains lead of

this appliance may not correspond with the coloured markings

identifying the terminals in your plug, proceed as follows:

– the wire which is coloured green and yellow must be

connected to the terminal in the plug which is marked with the

letter E or by the earth symbol [

], or coloured green or

green and yellow; – the wire which is coloured blue must be

connected to the terminal which is marked with the letter N or

coloured black; – the wire which is coloured brown must be

connected to the terminal which is marked with the letter L or

coloured red.

When making the electrical connections, check that the

voltage values correspond to those indicated on the data

plate inside the appliance itself. In case your appliance is not

furnished with a non separating flexible cable and has no

plug, or has not got any other device ensuring omnipolar

disconnection from the electricity main, with a contact opening

distance of at least 3 mm, such separating device ensuring

disconnection from the main must be included in the fixed

installation. If your unit features a power lead and plug,

position this so the plug is accessible.

Always switch off the electricity supply before carrying out

any cleaning or servicing operations on the appliance.

USE

Avoid using materials which could cause spurts of flame

(flambées) near the appliance.

When frying, take particular care to prevent oil and grease

from catching fire. Already used oil is especially dangerous in

this respect. Do not use uncovered electric grates.

To avoid possible risks of fire always comply with the indicated

instructions when cleaning anti-grease filters and when

removing grease deposits from the appliance.

MAINTENANCE

Thorough servicing guarantees correct and long-lasting

operation.

Any fat deposits should be removed from the appliance

periodically depending on amount of use (at least every 2

months). Avoid using abrasive or corrosive products. To

clean painted appliances on the outside, use a cloth dipped

in lukewarm water and neutral detergent. To clean steel,

copper or brass appliances on the outside, it is always best

to use specific products, following the instructions on the

products themselves. To clean the inside of the appliance,

use a cloth (or brush) dipped in denatured ethyl alcohol.

DEUTSCH

HINWEIS

Der Mindestabstand zwischen der Topf-Trägerfläche auf der

Kochmulde und dem unteren Teil der Abzughaube muss 65

cm betragen. Geben die Installationsanleitungen der

Kochmulde einen höheren Abstand an, so ist dieser

einzuhalten.

Ein Anschluss der Abluftleitungen an Verbrennung-

sabgaskamine (zum Beispiel Zentralheizung, Heizgeräte,

Badezimmeröfen usw.) ist nicht gestattet.

In jedem Fall sind bei der Ableitung der Abluft die behördlichen

Vorschriften zu beachten. Desweiteren darf die Abluft nur

dann durch ein Loch in der Wand geleitet werden, wenn

dieses für diesen Zweck bestimmt ist.

Achtung! Bei gleichzeitigem Betrieb einer Abluft-

Dunstabzugshaube und einer raumluftabhängigen

Feuerstätte (wie z. B. gas-, öl- oder kohlebetriebene

Heizgeräte, Durchlauferhitzer, Warmwasserbereiter) ist

Vorsicht geboten, da beim Absaugen der Luft durch die

Dunstabzugshaube dem Aufstellraum die Luft entnommen

wird, die die Feuerstätte zur Verbrennung benötigt. Ein

gefahrloser Betrieb ist möglich, wenn bei gleichzeitigem

Betrieb von Haube und raumluftabhängiger Feuerstätte im

Aufstellraum der Feuerstätte ein Unterdruck von höchstens

0,04 mbar erreicht wird und damit ein Rücksaugen der

Feuerstättenabgase vermieden wird. Daher den Raum mit

Lüftungsanschlüssen versehen, die einen konstanten Zustrom

von Frischluft gewährleisten.

Das Typenschild im Innern des Geräts kontrollieren: Den

folgenden Anweisungen folgen, falls das Symbol ( )

erscheint; dieses Gerät weist konstruktive technische

Details auf, die unter die Isolierungsklasse II fallen und

deshalb muss es nicht geerdet werden.

Das Typenschild im Innern des Geräts kontrollieren: den

folgenden Anweisungen folgen, falls das Symbol ( )

NICHT erscheint; ACHTUNG: dieses Gerät muss geerdet

werden. Beim elektrischen Anschluss sicherstellen, dass die

Steckdose eine Erdung aufweist.

Beim elektrischen Anschluss muss überprüft werden, ob die

Spannungswerte des Stromnetzes mit den Werten auf dem

im Innern des Gerätes angebrachten Typenschilds

übereinstimmen. Falls Ihr Gerät nicht mit einem fest

angeschlossenem Kabel mit Stecker oder einer sonstigen

WARNING - HINWEIS - ATTENTION - AVVERTENZE - ADVERTENCIA

ADVERTENCIAS - OPGELET

Page is loading ...

Faure AFT602W User manual

Brand: Faure

Model: AFT602W

Category: Cooker hoods

Type: User manual

This manual is also suitable for

Download PDF

report

in other languages

Deutsch: Faure AFT602W Benutzerhandbuch

Faure AFT602W User manual

This manual is also suitable for

Faure AFT602W User manual

in other languages

Related papers

Other documents