Waring WCS220SV User manual

Category
Slicers
Type
User manual

This manual is also suitable for

WCS220/250/300 Series
Food Slicer
Rebanadora de alimentos/
Cortadora de fiambre
Trancheuse
For your safety and continued enjoyment of this product,
always read the instruction book carefully before using.
Para su seguridad y para disfrutar plenamente de este producto,
siempre lea cuidadosamente las instrucciones antes de usarlo.
An que votre appareil vous procure en toute sécurité beaucoup de
satisfaction, lire attentivement le mode d’emploi avant de l’utiliser.
WCS220/250
WCS300
2
IMPORTANT UNPACKING INSTRUCTIONS
CAUTION: THE SLICING BLADE HAS A VERY SHARP EDGE.
To avoid injury when unpacking the unit, please follow these
instructions:
1. Put the box on a large, sturdy, at surface.
2. Remove the instruction book and other literature.
3. Position the box on its side, and then ip the box so that the
open side is facing the oor.
4. Lift up the box and remove the foam inserts.
5. Remove the protective bag.
6. To lift and move the unit, bend your knees to avoid back injuries,
and place one hand on the bottom of the motor housing and the
other one under the carriage.
7. Please use extreme caution when handling the blade. We
suggest you save all the packing materials in the event that
future shipping of the machine is needed.
Keep all plastic bags away from children.
REPACKING INSTRUCTIONS
1. Put food slicer on a large, sturdy, at surface.
2. Put food slicer into plastic bag.
3. Position foam inserts on each end of the food slicer.
4. Put the packaged unit into the upright box.
5. Replace top corrugated insert, instruction book and
other literature.
DELIVERY, PACKAGING AND STORAGE
TRANSPORT – HANDLING – STORAGE
The machine is packed in a cardboard box with
foam inserts.
The packaging is suitable for travel by all means
of transport.
It can be stacked one carton on another for a
maximum of three cartons.
– The packaging must be kept dry.
– To be handled by 2 persons.
When on pallets, handle only with electric lifters.
3
IMPORTANT SAFEGUARDS
When using electrical appliances, especially when children are
present, basic safety precautions should always be taken,
including the following:
1. READ ALL INSTRUCTIONS.
2. Unplug power cord from outlet when not in use, before
putting on or taking off parts, before cleaning, and before
attaching, adjusting or removing the blade sharpener.
3. Blade is exceptionally sharp. Handle very carefully.
4. To protect against risk of electric shock, do not put appliance in
water or other liquids.
5. Do not use appliance near children and individuals with certain
disabilities.
6. Avoid contact with moving parts.
7. Never put the unit near a hot burner, in an oven, or in a
dishwasher.
8. Do not operate the Waring
®
Commercial Food Slicer or
any electrical equipment with a damaged cord or plug, or after
the unit malfunctions, is dropped or damaged in any manner.
If damaged, immediately stop use and call Waring customer
service at (800) 269-6640. Return unit to the nearest Authorized
Service Center for examination, repair, or adjustment.
9. Do not use outdoors.
10. Do not let cord hang over the edge of a table or counter, come
into contact with sharp edges, or touch hot surfaces.
11. Place the appliance on a rm and stable surface. Ensure that
the appliance is not placed near the edge of the worktop, where
it can be easily pushed off or fall.
12. Never plug in the appliance where water may ood the area.
13. NEVER PUT YOUR FINGERS NEAR THE BLADE WHILE IT IS
IN OPERATION.
14. The use of attachments not recommended or sold by the
manufacturer may cause re, electric shock or injury.
15. Use the slicer to cut ONLY designated food. Do not attempt
to slice frozen food or materials such as bones, cardboard,
plastic, etc.
4
16. TO PROTECT AGAINST ANY RISK OF ELECTRIC
SHOCK, DO NOT PUT THE APPLIANCE IN WATER
OR IN ANY OTHER LIQUIDS.
17. The Waring
®
Food Slicer has a sharp blade. To avoid injury,
never hand-feed food to be sliced. Always use the unit when
completely assembled with food carriage and food guide.
18. WARNING: This appliance is not intended for use by persons
(including children) with reduced physical, sensory, or mental
capabilities, or lack of experience and knowledge, unless they
have been adequately trained to do so in a safe manner. It is
better to watch over children to be sure they do not play with
the device. Use of this appliance must be carried out with the
utmost care as it concerns a cutting device.
19. Always use completely assembled slicers with food tray
and food holder arm and with all the protective parts.
20. The use of spare parts not recommended or sold by
manufacturer may cause re, electric shock or injury.
21. Do not catch slices with your hand.
22. Children should be supervised to ensure that they do not play
with the appliance.
23. Do not use the machine with the protective parts removed.
24. Waring declines all responsibility in the case of improper use of
the machine. Do not use the food slicer for frozen food, bone-in
meat or anything other than foodstuffs. Periodically check the
state of the cable; should it be damaged, it must be replaced by
qualied staff.
25. Do not submerge the food slicer in water when cleaning.
26. The slicer is not to be washed by the use of a waterjet.
27. Do not use extension cords.
28. Do not unplug by pulling the cord.
29. Do not use the machine with wet hands or bare feet.
30. Do not place slicer near sources of heat.
31. Even though the machine is equipped with safety devices, keep
your hands away from the blade and moving parts.
5
SAVE THESE INSTRUCTIONS.
FOR COMMERCIAL USE ONLY
GROUNDING INSTRUCTIONS
This appliance must be grounded while in use to protect the operator
from electric shock. The appliance is equipped with a 3-conductor
cord and 3-prong grounding-type plug to t the proper grounding-
type receptacle. The appliance has a plug that looks like the plug
in drawing (1). An adapter, as in drawing (2), should be used for
connecting the appliance plug to two-prong receptacles.
The grounding lug, which extends from the adapter, must be
connected to a permanent ground such as a properly grounded
outlet box, as shown in drawing (3), using a metal screw.
NOTE: The use of an adapter is not authorized in Canada.
6
CONTENTS
1. Unpacking Instructions ..................................................................2
2. Delivery, Packaging and Storage ...................................................2
3. Important Safeguards ....................................................................3
4. General Information ....................................................................... 6
5. Safety .............................................................................................6
6. Technical Data ................................................................................ 7
7. Installation and Operation ...............................................................9
8. Cleaning and Sanitizing Instructions ............................................ 12
9. Troubleshooting ............................................................................16
10. Waste Disposal ........................................................................... 17
11. Warranty / Service ......................................................................17
GENERAL INFORMATION
PRESENTATION
The aim of this handbook is to provide the customer with as much
information as possible about our food slicer, and instructions for
its use and maintenance in order to keep it working efciently. This
handbook should be given to those responsible for the use and
periodical maintenance of the slicer. The handbook should be kept
in good condition and stored in an easily accessible place for
quick reference.
IMPORTANCE OF THE HANDBOOK
The handbook is an integral part of the machine. It includes
important information regarding safety and danger, pointed out
by these symbols:
The information included will allow you to use the machine in
perfectly safe conditions and to obtain the best results.
SAFETY
MAIN VOLTAGE
Before plugging in, check that the main voltage corresponds to the
voltage indicated on the food slicer (see data plate).
WARNINGS AND SAFETY RULES
READ ALL INSTRUCTIONS
7
Read carefully all the instructions before using the machine, taking
particular care of the paragraphs with the safety and danger symbols.
CONTROL
Transmission.
Immediately after installation, check that the
appliance is operating correctly as follows:
Ensure the thickness control knob (6) is in
“0” position.
– Switch on the slicer.
Using a cloth, push on the blade (3), to try to
brake it; the blade must not stop. If the blade does
stop, return appliance to Waring service center.
Sliding capacity of the food tray group carriage.
Check that the carriage slides across
its full range. It is possible that some
pieces of the packaging remain on
the sliding bars (28 and 29) and can
impede the sliding mechanism.
Clean the square bar (28) indicated
in the picture with a cloth (avoid
degreasing the bar).
Periodically, after having cleaned the cylindrical sliding bar (29),
lubricate it with Petro-Gel or similar food-grade oil (30).
Sharpener group.
Check the insertion of the sharpener assembly (see #10 on
illustration) in its seat, to make sure the sharpener is properly
mounted and to ensure it is secure.
TECHNICAL DATA – DIMENSIONS
COMMON TECHNICAL CHARACTERISTICS
– Structure is cast aluminum
Blade guard, food tray and movable bulkhead: in oxidized aluminum
Shaft holding the blade is mounted on a double ball-bearing
Professional, ventilated motor
Tempered, professional blade
9
Slicer Info WCS220 WCS250 WCS300
Dimensions in Inches L x W 18.8 x 20.8 18.9 x 20.8 18.9 x 21.6
Height Less Sharpener 13.9 14.7 16.9
Height w/Sharpener 15.2 15.2 19.4
Blade Diameter 8.5 in. 10 in. 12 in.
Power ¾ HP* ¾ HP* 1 HP*
Capacity of Cut
(approx)
8.2 x 5.7 8.6 x 6.2 7.8 x 8.0
Carriage Stroke 9.2 9.2 9.2
Weight 28.6 lb. 30.9 lb. 38.5 lb.
Slice Thickness 0-0.59"/15mm 0-0.59"/15mm 0-0.59"/15mm
INSTALLATION AND OPERATION
INSTALLATION
Environmental conditions:
Minimum temperature above
46°F (7.7 °C)
Maximum temperature below
100°F (37.7 °C)
– Minimum moisture 30%
– Maximum moisture 80%
The slicer must be put on a
stable support to prevent it from moving.
The cord has to be connected in a manner that will not create a
tripping hazard.
Leveling
Check that the movable bulkhead (2) with the thickness control knob
(6) in “0” position is aligned to the blade in the zone (see above).
If it is not aligned, adjust the feet (12) by unscrewing or screwing the
right foot.
PARTS
1 – Food holder arm
2 – Movable bulkhead
3 – Blade
4 – Blade cover
*
Peak input watts.
10
5 – ON / OFF switch
6 – Thickness control knob
7 – Sliding carriage or sliding food tray
9 – Blade cover release knob
10 – Sharpener group
12 – Feet
13 – Sharpener group locking knob
OPERATION
With the slicer turned off, pull the slicing food tray (7) completely
toward you and place the food product onto the food tray. Slice only
boneless, unfrozen product with the slicer.
Make sure all knobs are tightened prior to using the slicer.
Rotate the slice thickness dial counterclockwise to the desired
setting. After slicing is complete, always turn the slice thickness
control knob clockwise to the “0” position.
Turn the slicer on by pushing the green ON switch. The Power
indicator light will illuminate.
To turn the slicer off, press the OFF switch.
NEVER ATTEMPT TO ADJUST LOAD OR UNLOAD FOOD TRAY
WHEN SLICER IN OPERATION.
BLADE SHARPENING – for blade diameter:
", 10", 12" Blades
NOTE: It should be noted that the blade is highly resistant;
therefore, it needs to be sharpened only when the cutting
performance decreases.
Unplug slicer from electrical outlet.
Check that the movable bulkhead (2) is closed (thickness control
knob (6) in position “0”). See Fig. 2.
Carefully clean the part of the blade that needs to be sharpened.
11
Reinsert the plug.
Loosen the locking knob (13) of the sharpener group (10).
See Fig. 1.
Raise the sharpener group (10), turning it by 180° so that both
wheels are in working position. See Fig. 2.
Lower the sharpener group (10) until it locks. See Fig. 2.
Secure the group by turning the locking knob (13). See Fig. 3.
Switch on (5). See Fig. 2.
Press button (26) and let the blade turn for about 1 minute. Turn
slicer off (5). When the blade is still, check to see if any burrs have
formed on the edge. See Fig. 2.
After having veried the presence of burr, switch on and gently
press button (27) for about 3 seconds to remove the burr
produced during sharpening. See Fig. 2.
After sharpening, move the sharpener group (10) back to its
original position and clean the edge of the blade and the wheels.
After several sharpening operations, remove any residue from the
sharpening wheel with alcohol and a brush.
CLEANING AND SANITIZING INSTRUCTIONS
THE SLICER MUST BE THOROUGHLY CLEANED, RINSED,
SANITIZED AND DRIED AFTER EACH DAY OF USE ACCORDING
TO THE FOLLOWING INSTRUCTIONS.
FAILURE TO DO SO MAY ALLOW RESIDUE OF SLICED MATERIAL
TO COLLECT ON THE UNIT.
Never use abrasive cleaning agents or abrasive cloths when
cleaning the unit.
Remove the plug before the maintenance and disassembly
operations for cleaning of the protective parts.
Wash, rinse, sanitize and dry slicer prior to initial use and whenever
it has not been used for an extended period of time.
Wash and rinse blade and slicing carriage after each use.
Clean and sanitize motor base prior to initial use and after
each use.
Washing solutions based on non-sudsing detergents and
chlorine-based sanitizing solutions having a minimum chlorine
concentration of 100 PPM are recommended.
12
Before carrying out any maintenance operation, unplug the
machine and make sure that the thickness control knob is in the
“0” position. Remove the blade guard periodically, by removing the
screw (in the center of the blade guard). Then clean both the blade
and the inside of the blade guard with alcohol or warm water.
The following washing, rinsing, and sanitizing solutions, or their
equivalents, may be used.
Do not use jets of water.
Do not hose down slicer or splash excessively with water.
Do not wash any slicer components in a dishwasher.
Do not use brushes that can damage the surface of the
machine.
Do not clean any parts of the slicer with a steel or abrasive pad.
Do not move the machine to clean it.
EASY-CLEAN SYSTEM
1. Make sure that the thickness control knob is in position “0
– Fig. 1 (the system operates only if the thickness control
knob is in position “0”).
2. Pull the carriage toward the
thickness control knob and tilt the carriage outward – Fig. 2/3.
3. Proceed with the cleaning.
SOLUTION PRODUCT DILUTION IN WATER TEMPERATURE
Washing International Products
Corporation LF2100
®
Liquid Low-Foam
Cleaner
1%–2%: 1¼ – 2¾
Ounce/Gallon (lower dilution of 1%
for normal cleaning and up to 2%
for more stubborn soils)
Room
Temperature
Rinsing Plain Water Warm 95˚F (35˚C)
Sanitizing Clorox
®
Regular Bleach
(8.25% Hypochlorite
Concentration)
2 Teaspoons/Gallon (Alternately,
a bleach with 5.25% Hypochlorite
Concentration can be used at
dilution of 3 Teaspoons/Gallon)
Between
50˚F and 120˚F
(10˚C to 49˚C)
13
CLEANING OF THE BLADE
BLADE IS SHARP. HANDLE
CAREFULLY WHEN CLEANING.
It is not necessary to disassemble
the blade when cleaning it because
all its parts are reachable. The blade
is very sharp.
WARNING: The replacement of the
blade must be made by specialized
personnel.
The blade has to be replaced when
it is not possible to sharpen it, or
when the distance between the
cutting part of the blade and the
blade guard is more than 1/4 inch.
The machine and all its parts
should be cleaned with soft cloths
moistened with standard, neutral
detergents.
Use soft cloths for drying. When the
sliding carriage moves with difculty,
lift the food slicer and place it on its
side. Carefully clean the cylindrical
sliding bar and lubricate it with
lithium grease or a similar product.
BEFORE CLEANING, SHARPENING, SERVICING OR REMOVING
ANY PARTS, ALWAYS TURN SLICER OFF. Turn the slice thickness
dial clockwise to the “0” position until it stops, and unplug power
cord.
NEVER attempt to clean slicer with the blade running.
NEVER attempt to remove the blade or blade guard from the slicer.
They must remain on the slicer for proper operation, sharpening and
cleaning.
FIG. 1
FIG. 2
FIG. 3
14
WARNING: The slicer blade is very sharp. Exercise extreme caution
when working near the blade.
It is recommended to use the proper anti-cut gloves to avoid
danger of cutting.
– Disassemble the blade cover (4).
Loosen the blade cover release knob (9), unthread it and remove
the blade cover.
IMPORTANT! A micro switch interrupts electrical current supply
whenever the blade cover release knob (9) is removed.
Use a soft cloth moistened with a neutral detergent and wipe blade
from the center out.
Rinse with hot water and dry.
An important step to kill bacteria is to allow the parts to air-dry
before using.
DO NOT exceed chemical manufacturer’s recommended
concentrations for detergent or sanitizer. Do not exceed
200 parts per million concentration of available chlorine
(1 tablespoon of 5.25% sodium hypochlorite bleach with
1 gallon of water). The effect of the sanitizing solution varies
with its temperature and concentration.
NOTE: Failure to follow use, care and maintenance instructions
may void your warranty.
Use ONLY products formulated to be safe on stainless steel
or aluminum.
Clean the blade (3) on both faces
as indicated in the drawings.
15
WHEEL CLEANING
After many sharpening
operations, clean the
sharpening stones (10)
of sharpening residue
with a metallic brush.
Wipe sharpening wheels with alcohol after cleaning.
Any other servicing should be performed by an authorized service
representative.
GASKET INSPECTION
The recommended interval between
inspections shall not exceed six months for
components that are detached for cleaning
and sanitizing and twelve months for all others.
The inspections must be made by the
manufacturer or its authorized service agent.
WARNING
The slicer must be removed from service until repaired by the
manufacturer or its Waring authorized service agent if any gasket or
seal is found to be damaged, or missing.
Inspections instructions shall include: Location of all gaskets and
seals located in food and splash zones.
REMOVABLE
ACCESSORY PARTS
NOTE: Contact your nearest
authorized service center for blade
replacement
Transmission
The transmission is made by a
multigrip belt. It is not necessary to
regulate.
Do not let dirt or oil come into
contact with the transmission, as
this will affect the performance of
the slicer.
In that case, it must be replaced,
taking care of de-greasing both
the motor pin and the pulley.
Gasket between
slice thickness
control
Protection on
the switch
WCS300 WCS220/250
16
Electric cord
Periodically check its condition (there must not be any kinks). If
the cord is damaged, it has to be replaced. Please return it to an
authorized service center for replacement.
Blade
The blade has to be replaced when it is not possible to sharpen
it or when the distance between the cutting part of the blade and
the blade guard is more than 1/4 inch. Please contact your nearest
authorized service center for replacement.
Sharpening stones of the sharpener
These stones, after a lot of sharpening operations, lose their abrasive
action and they must be replaced. Contact your nearest authorized
service center for replacement.
TROUBLESHOOTING GUIDE
SYMPTOM CAUSE SOLUTION
Slicer will not start Slicer not plugged in
Blade cover removed or not
properly installed
Plug in slicer
Install blade cover and tighten the
blade cover release knob
Ragged cuts,
poor yield
Dull blade
Chipped blade
Blade too small
Sharpen blade; make sure blade and
stones are clean
Sharpen or have new blade installed
Have new blade installed
Metal rubbing
on blade
Blade cover not tightened/
properly installed
Tighten blade cover release knob
Hard-to-push food
carriage assembly
No lubrication Lubricate sliding bars thoroughly with
Petrol-Gel or similar. No vegetable oil!
Hard to sharpen Stones dirty, wet or clogged
with grease
Blade dirty
Worn stones
Stones not properly aligned
Clean stones with warm water and
a brush. Allow stones to air-dry and
lubricate shafts with Petro-Gel or
similar.
Clean top and bottom of blade
Have stones replaced
Have sharpener adjusted
Slicer stops running Motor overheated Unplug unit and wait 1015 minutes
for slicer to cool down. Turn unit back
on and push the ON button. If problem
persists, contact an authorized service
center.
17
LIMITED ONE-YEAR WARRANTY
(U.S. AND CANADA ONLY)
Waring warrants every new WARING COMMERCIAL PRODUCT
to be free from defects in materials and workmanship for a period
of one year from the date of purchase when used with foodstuffs,
nonabrasive liquids (other than detergents) and nonabrasive semi-
liquids, providing it has not been subject to loads in excess of the
indicated rating.
Under this warranty, the Waring Commercial Division will repair
or replace any part which, upon our examination, is defective in
materials or workmanship, provided the product is delivered prepaid
to the Waring Service Center, 314 Ella T. Grasso Ave., Torrington, CT
06790 or any Factory Approved Service Center.
This warranty does not: a) apply to any product that has become
worn, defective, damaged or broken due to misuse or due to repairs
or servicing by other than the Waring Service Center or a Factory
Approved Service Center or due to abuse, misuse, overloading or
tampering; b) cover consequential damages of any kind.
The one-year warranty is applicable only to appliances used in the
United States and Canada; this supersedes all other express product
warranty or guarantee statements.
Warning: This warranty is VOID if appliance is used on Direct
Current (DC).
Trademarks or service marks of third parties used herein are
the trademarks or service marks of their respective owners.
Todas las marcas registradas, comerciales o de servicio mencionadas
en este documento pertenecen a sus titulares respectivos.
Toutes les marques déposées, commerciales ou de service
ci-incluses appartiennent à leurs propriétaires respectifs.
©2018 Waring Commercial
314 Ella T. Grasso Ave.
Torrington, CT 06790
www.waringcommercialproducts.com
Made and printed in Italy
WCS220/250/300 Series IB
18WC051454
IB-15300
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52

Waring WCS220SV User manual

Category
Slicers
Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI