Finlux 24F6030 User manual

Category
LCD TVs
Type
User manual
24in LED TV
24F6030
Owner’s manual
happy Finnish
- 1 -
Contents
Package Contents .................................................. 2
Features ................................................................. 2
Introduction ............................................................. 3
Preparation ............................................................. 3
Safety Precautions ................................................. 3
Electrical devices not in the hands of children .... 4
Environmental Information ..................................... 5
Repair Information .............................................. 5
Remote Control Buttons ......................................... 6
TV and Operating Buttons ...................................... 7
Viewing the Connections - Back Connectors ......... 7
Viewing the Connections - Side Connectors .......... 8
Aerial Connection ................................................... 8
Power Connection .............................................. 8
Using USB Media ................................................... 9
Connecting the TV to a PC ................................... 10
Connecting to a DVD Player................................. 10
Using Side AV Connectors ....................................11
Remote Control Handset .......................................11
Inserting Batteries ..............................................11
Switching On/Off ....................................................11
To Switch the TV On ..........................................11
To Switch the TV Off ..........................................11
Input Selection .......................................................11
Basic Operations .................................................. 12
Operation with the Buttons on the TV ............... 12
Operation with the Remote Control .................. 12
First Time Installation............................................ 12
Viewing Electronic Programme Guide (EPG) ....... 13
EPG Timeline Schedule .................................... 13
EPG Channel Schedule .................................... 14
EPG Now and Next........................................... 14
Recording via EPG Screen ............................... 14
Programme Options.......................................... 14
Installation ............................................................ 15
Auto Channel Scan (Retune) Menu Operation . 15
Manual Tuning ..................................................... 15
Digital Manual Search....................................... 15
Analogue Manual Search ................................. 15
Analogue Fine Tune.......................................... 15
Managing Stations: Channel List .......................... 16
Operating the Channel List ............................... 16
Moving a Channel ............................................. 16
Deleting a Channel ........................................... 16
Renaming a Channel ........................................ 16
Locking a Channel ............................................ 16
Managing Stations: Favourites ............................. 17
Button Functions ............................................... 17
Managing Stations: Sorting the Channel List ....... 17
On-Screen Information ......................................... 17
Media Playback Using Media Browser ................. 17
Viewing Videos via USB .................................. 18
Viewing Photos via USB ................................... 18
Slideshow Options ............................................ 18
Playing Music via USB ..................................... 19
Recordings Library............................................ 19
Media Browser Settings .................................... 20
Timeshift Recording ............................................. 20
Instant Recording ................................................. 20
Watching Recorded Programmes ....................... 21
Changing Image Size: Picture Formats ................ 21
Conguring Picture Settings ................................. 22
Operating Picture Settings Menu Items ............ 22
Picture Settings Menu Items ............................. 22
PC Picture Settings........................................... 23
Conguring Sound Settings .................................. 23
Operating Sound Settings Menu Items ............. 23
Sound Settings Menu Items.............................. 23
Conguring Your TV’s Settings ............................. 24
Operating Settings Menu Items ........................ 24
Settings Menu Items ......................................... 24
Using a Conditional Access Module (not
included) ............................................................... 24
Viewing Conditional Access Menu (*) ............... 24
Conguring Language Preferences ...................... 25
Parental Control.................................................... 25
Parental Settings Menu Operation ................... 25
Timers ................................................................... 26
Recording Conguration ....................................... 26
Conguring Date/Time Settings ............................ 27
Conguring Source Settings ................................. 27
Conguring Other Settings ................................... 27
Operation .......................................................... 27
Other Features ..................................................... 28
Teletext ................................................................. 28
Tips ....................................................................... 29
Appendix A: PC Input Typical Display Modes ....... 30
Appendix B: AV and HDMI Signal Compatibility
(Input Signal Types) .............................................. 30
Appendix C: Supported DVI Resolutions.............. 31
Appendix D: Software Upgrade ............................ 31
Appendix E : Supported File Formats for USB
Mode..................................................................... 32
Specications ....................................................... 33
Important Instruction ............................................. 34
- 2 -
Package Contents
REPEAT
ZOOM
TITLE
ROOT
TEXT
SWAP
1
2
3
4
5
6
7
8
9
SCREEN
0
LANG SUBTITLE
OK
MENU
SOURCE
RETURN
INFO
FAV SLEEP EPG
SEARCH
DISPLAY
MODE
P+
PRESETS
P-
V+
V -
Remote Control
LCD TV
Instruction Book
Batteries: 2 X AAA
1 X Video & Audio Connection Cable
Note: You should check the contents after opening
your purchase and make sure that every item is
included.
Note: The HDMI connection between PC and TV
may cause radio interference in which case it is
recommended to use VGA(DSUB-15) connection.
Features
Remote controlled colour LCD TV.
Fully integrated Terrestrial digital TV (DVB-T
MPEG2).
HDMI connectors for digital video and audio.
USB input.
Programme recording
Programme timeshifting
1000 programmes (analogue+digital).
On Screen Display (OSD) menu system.
Integrated tuner DVB-T, MPEG2 compatible.
Scart socket for external devices.
Stereo sound system. (Nicam)
Teletext, fastext, TOP text.
Headphone connection.
Automatic programming system.
Forward or backward manual tuning.
Sleep timer / Child lock.
Automatic sound mute when no transmission.
NTSC playback.
AVL (Automatic Volume Limiting).
Auto power down.
PLL (Frequency Search).
PC input.
Plug&Play for Windows 98, ME, 2000, XP, Vista,
Windows 7.
Game Mode
- 3 -
Introduction
Thank you for choosing this product. This manual
will guide you through the proper operation of your
TV. Before operating the TV, please read this manual
thoroughly. Please keep this manual in a safe place
for future reference.
This device is intended to receive and display TV
programmes. The different connection options make
an additional expansion of the reception and display
sources possible (receiver, DVD player, DVD recorder,
VCR, PC etc.).
This device is only suitable for dry indoor use. This
appliance is intended solely for private domestic use
and may not be used for industrial and commercial
purposes. We exclude liability in principle, if the device
is not used as intended, or unauthorized modications
have been made. To operate your LCD TV in extreme
ambient conditions may cause the damage of the
device.
Preparation
For ventilation, leave a free space of at least 10 cm
all around the set. To prevent any fault and unsafe
situations, please do not place any objects on top of
the set. Use this device in moderate climates.
10 cm
10 cm
10 cm
Safety Precautions
Read the foll owing recommended safet y
precautions carefully.
Power Source
The TV set should be operated only from a 220-240V
AC, 50 Hz outlet. Ensure that you select the correct
voltage setting for your convenience.
Power Cord
Do not place the set, a piece of furniture, etc. on the
power cord or pinch the cord. Handle the power cord
by the plug. Do not unplug the appliance by pulling from
the power cord and never touch the power cord with wet
hands as this could cause a short circuit or electric shock.
Never make a knot in the cord or tie it with other cords.
The power cord should be placed in such a way that they
are not likely to be stepped on. A damaged power cord
can cause re or give you an electric shock. When it is
damaged and needs to be replaced, it should be done
by qualied personnel.
Moisture and Water
Do not use this device in a humid and
damp place (avoid using the TV in the
bathroom or near the Kitchen sink etc).
Do not expose this device to rain or
water, as this may be dangerous and
do not place objects lled with liquids,
such as ower vases, on top.
If any solid object or liquid falls into the cabinet, unplug
the TV and have it checked by qualied personnel
before operating it any further.
Cleaning
Before cleaning, unplug the TV set
from the wall outlet. Do not use liquid or
aerosol cleaners. Use a soft, dry cloth.
Ventilation
The slots and openings on the TV set
are intended for ventilation and to ensure reliable
operation. To prevent overheating, these openings
must not be blocked or covered in anyway.
Heat and Flames
The set should not be placed near to
open ames or sources of intense heat
such as an electric heater. Ensure that
no open ame sources, such as candles,
are placed on top of the TV. Batteries should not be
exposed to excessive heat such as sunshine, re or
the like.
Lightning
In case of storm and lightning or when
going on holiday, disconnect the power
cord from the wall outlet.
Replacement Parts
When replacement parts are required, make sure that
the service technician has used replacement parts,
which are specied by the manufacturer or have the
same specications as the original one. Unauthorized
substitutions may result in re, electrical shock or
other hazards.
Servicing
Please refer all servicing to qualied
personnel. Do not remove the cover
yourself as this may result in an electric
shock.
- 4 -
Connection to a Television Distribution
System (Cable TV etc.) from Tuner
Devices connected to the protective earthing of the
building installation through the mains connection or
through other apparatus with a connection to protective
earthing-and to a television distribution system using
a coaxial cable, may in some circumstances create
a re hazard.
Connection to a cable distribution system has
therefore to be provided through a device providing
electrical isolation below a certain frequency range
(galvanic isolator, see EN 60728-11).
Electrical devices not in the hands of
children
Never let children use electrical devices unsupervised.
Children cannot always recognize properly any
possible danger. Batteries / accumulators can be life
threatening when swallowed. Store batteries out of
the reach of small children. In case of swallowing a
battery, medical aid has to be sought immediately.
Also keep the packaging away from children as there
is danger of suffocation.
The Standby button does not fully switch off this
product. Moreover, the device continues to consume
power in standby mode. In order to separate the
device completely from mains, the mains plug has to
be pulled from the mains socket. Because of that the
device should be set up in a way, that an unobstructed
access to the mains socket is guaranteed, so that
in case of emergency the mains plug can be pulled
immediately. During periods of prolonged non-use,
the TV should be disconnected from the mains power
supply.
TRADEMARK ACKNOWLEDGMENT
“Dolby” and the double-D symbol are trademarks of
Dolby Laboratories.
Licence Notication (Optional)
M a n u f a cture d u n d e r li c e n s e f rom D o l b y
Laboratories.
Waste Disposal
Instructions for waste disposal:
Packaging and packaging aids are recyclable
and should principally be recycled. Packaging
materials, such as a foil bag, must be kept away
from children.
Batteries, including those which are heavy metal-
free, should not be disposed of with household
waste. Please dispose of used batteries in an
environmentally friendly manner. Find out about the
legal regulations which apply in your area.
Do not try to recharge batteries, there is a danger
of explosion. Replace batteries only with the same
or equivalent type.
This symbol on the product or on its packaging means
that your electrical device should be
disposed at the end of its service life
separately from your household wastes.
There are separate collection systems for
recycling in the EU. For more information,
please contact the local authority or the
dea ler whe re you purcha sed the
product.
Disconnecting the Device
The mains plug is used to disconnect the TV set
from the mains and therefore it must remain readily
operable.
Headphone Volume
Excessive sound pressure from earphones
and headphones can cause hearing loss.
Installation
To prevent injury, this device must be securely
attached to the wall in accordance with the installation
instructions when mounted to the wall (if the option
is available).
LCD Screen
The LCD panel is a very high technology product with
about a million thin lm transistors, giving you ne
picture details. Occasionally, a few non-active pixels
may appear on the screen as a xed blue, green or
red point. Please note that this does not affect the
performance of your product.
Warning! Do not leave your TV in standby or operating
mode when you leave your house.
- 5 -
Environmental Information
This television is designed to consume less energy to save the environment.
You not only help to save the environment but you can also save money by reducing electricity bills thanks to the
energy efciency features of this TV. To reduce energy consumption, you should take the following steps:
You can use the Power Save Mode setting, located in the Other settings menu. If you set the Power Save
Mode as On, the TV will switch to energy-saving mode and the luminance level of the TV set will be decreased
to optimum level. Note that some picture settings will be unavailable when the TV is in Power Save Mode.
When the TV is not in use, please switch off or disconnect the TV from the mains plug. This will also reduce
energy consumption.
Note that annually, using the TV set in Power Save Mode has more power efciency than disconnecting
the TV from the mains plug instead of keeping stand-by mode. Therefore it is highly recommended to
activate Power Save Mode setting to reduce your annual power consumption. And also it is recommended
to disconnect the TV from the mains plug to save energy more when you do not use.
• Please help us to save environment by following these steps.
Repair Information
Please refer all servicing to qualied personnel. Only qualied personnel must repair the TV. Please contact
your local dealer, where you purchased this TV for further information.
- 6 -
Remote Control Buttons
REPEAT
ZOOM
TITLE
ROOT
TEXT
SWAP
1
2
3
4
5
6
7
8
9
SCREEN
0
LANG SUBTITLE
OK
MENU
SOURCE
RETURN
INFO
FAV SLEEP EPG
SEARCH
DISPLAY
MODE
P+
PRESETS
P-
V+
V-
No function1.
Play (in Media Browser mode) 2.
Programme recording3.
Rapid reverse (in Media Browser mode)4.
No function5.
Mono/Stereo - Dual I-II / Current Language (*) / 6.
Play preview (in Media Browser mode)
Image size 7.
Green button 8.
Red button9.
Numeric buttons10.
Teletext / Mix 11.
Info / Reveal (in TXT mode)12.
Programme Down - Page up / Programme Up - 13.
Page down
Mute14.
Favourite mode selection15.
Exit (in DTV mode) / Return / Index page (in 16.
TXT mode)
No function (*)17.
No function18.
Recordings Library19.
Picture mode selection 20.
Electronic Programme Guide21.
Sleep timer22.
Menu on/off23.
OK / Select / Hold (in TXT mode) / Channel List24.
Volume up / down25.
Navigation buttons26.
AV / Source27.
Previous programme / Now (in EPG mode)28.
Blue button29.
Yellow button 30.
No function (**)31.
Subtitle on-off / TXT subtitle (analogue TV 32.
mode) / Subtitle (in Media Browser mode).
No function33.
Rapid advance (in Media Browser mode)34.
Stop (in Media Browser mode)35.
Pause / Timeshift recording36.
Standby37.
Operation LED light38.
These buttons change according to the model:
/ Media Browser (optional) (*) or Angle / No
function (*)
/ Web Browser (optional) (**) or Pip / Pip function
(optional) (**)
- 7 -
TV and Operating Buttons
FRONT and REAR VIEW
Control switch VIEW
Control Switch
Up direction1.
Down direction2.
Programme/Volume / AV / 3.
Standby-On selection switch
Note: You can move the switch,
upward or downward to change
the volume. If you want to change
the channel, press the middle of
the switch once (Position 3) and
then move upward or downward. If
you press the middle of the switch
once more, the source OSD will
be displayed. To select desired
source, move the switch upward or
downward and release. If you press
the middle of the switch and hold for
a few seconds, the TV will switch
to standby mode. The Main menu
OSD cannot be displayed via the
control buttons on the TV.
Viewing the Connections - Back Connectors
HDMI 2: HDMI Input1.
HDMI 1: HDMI Input 2.
HDMI Inputs are for connecting a device that has a HDMI socket. Your TV is capable of displaying high
denition pictures from devices such as a High Denition Satellite Receiver or Blu-ray Player. Please
see Appendix B for further details
RF Input3. connects to an aerial antenna system.
Note: If you use a decoder or a media recorder, you should connect the aerial cable through the device to
the television with an appropriate antenna cable, as shown in the illustration in the following pages.
SCART 4. input or output for external devices. Connect the SCART cable between the SCART socket on the
TV and the SCART socket on your external device (such as a decoder, a VCR or a DVD player).
Note: If an external device is connected via the SCART socket, the TV will automatically switch to AV mode.
Note: S-VHS signal is supported via the scart socket(optional).
- 8 -
VGA Input5. is for connecting a personal computer to the TV set.
Connect the PC cable between the PC INPUT on the TV and the PC output on your PC.
SPDIF Out6. outputs audio signals of the currently watched source.
Use an SPDIF cable to trasfer audio signals to a device that has SPDIF input.
Viewing the Connections - Side Connectors
The CI Slot is used for inserting a CI card. A CI card allows you to view all the channels that you 1.
subscribe to. For more information, see “Conditional Access” section.
Side USB input. 2.
Note: That programme recording feature is available via this USB input. You can
connect external hard disk drives to this input.
Video Input is used for connecting video signals of external devices.Connect the video 3.
cable between the VIDEO IN socket on the TV and the VIDEO OUT jack on your
device.
Audio Inputs are used for connecting audio signals of external devices. Connect the audio cable 4.
between the AUDIO INPUTS on the TV and the AUDIO OUTPUT jacks on your device.
Note: If you connect a device to the TV via the VIDEO INPUT, you should also connect your
device with an audio cable to the AUDIO INPUTS of the TV to enable audio.
The headphone jack is used for connecting an external headphone to the system. 5.
Connect to the HEADPHONE jack to listen to the TV from headphones.
Aerial Connection
Connect the aerial to the AERIAL INPUT (ANT) socket located at the rear of the TV.
D I H M 1
SPDIF
Coax.OUT
D I H M 2
Power Connection
IMPORTANT: The TV set is designed to operate on 220-240V AC, 50 Hz.
After unpacking, allow the TV set to reach the ambient room temperature before you connect the set to the
mains.
- 9 -
Using USB Media
USB Connection
You can connect a USB hard disk drive or USB
memory stick to your TV by using the USB inputs
of the TV. This feature allows you to play les stored
in a USB drive or record programmes.
2.5” and 3.5” inch (hdd with external power supply)
external hard disk drives are supported.
To record a programme, you should rst connect
a USB disk to your TV while the TV is switched
off. You should then switch on the TV to enable
recording feature. Otherwise, recording feature will
not be available.
IMPORTANT !
You may back up your les before making any
connections to the TV set in order to avoid any
possible data loss. Note that manufacturer will not
be responsible for any le damage or dataloss.
It is possible that certain types of USB devices (e.g.
MP3 Players) or USB hard disk drives/memory sticks
may not be compatible with this TV.
IMPORTANT: The TV supports only FAT32 disk
formatting. NTFS format is not supported. If you
connect a USB disk with NTFS format, the TV will ask
you to format the content. See the section, “Format
Disk” in the following pages for more information on
disk formatting.
Note that ALL the data stored on the USB disk will
be lost and then the disk format will be converted to
FAT32 in such a case.
USB Disk Connection
• Plug your USB device to the USB input of the TV.
Note: Plug or unplug your USB disk while the TV is
switched off.
Note: If you are going to connect a USB hard disk drive
to the TV set, USB connection cable used between
the disk drive and the TV should have a USB logo
and should be as short as possible.
Note: While formatting a USB hard disk that has 1TB
(Tera Byte) or more le capacity, you can experience
problems with the formatting process. In such a
case, you should format the disk with your personal
computer and the formatted disk type should be
FAT32.
SIDE VIEW USB MEMORY
5Vdc
Max:500mA
USB
CAUTION !
Quickly plugging and unplugging USB devices,
is a very hazardous operation. Especially, do not
repeatedly quickly plug and unplug the drive. This
may cause physical damage to the USB player and
especially the USB device itself.
Do not pull out USB module while playing or
recording a le.
Programme Recording
To record a programme, you should rst connect a
USB disk to your TV while the TV is switched off.
You should then switch on the TV to enable recording
feature.
IMPORTANT: When using a new USB hard disk drive,
it is recommended that you rst format the disk using
your TV’s “Format Disk” option.
For using recording function, you should connect a
USB disk or an external hard disk drive to the TV
and connected USB disk should have at least 1 GB
capacity and should have 2.0 speed compatibility.
If the connected USB device does not support 2.0
speed, an error message will be displayed.
Note: Recorded programmes are saved into the
connected USB disk. If desired, you can store/copy
recordings on a computer; however, these les will
not be available to be played on a computer. You can
play the recordings only via your TV.
An hour of the recordings stored occupies
approximately 2 GB of space.
For more information on recording programmes,
see sections “Instant Recording”, Timeshifting”,
“Electronic Programme Guide”, “Recordings Library”
or “Recording Timers” in the following parts.
Record ed programmes are split into 4GB
partitions.
Recorded programmes are stored in the following
directory of the connected USB disk: \DVR\RECS.
All recordings are indicated with a number. A text
(txt) le is created for each recording. This text
file includes information such as broadcaster,
programme, and recording time.
Timeshifting may be stopped according to USB
device write speed. If the USB device speed is not
enough for video stream bitrate, timeshifting may
be stopped and recording may fail. If HD service
bitrate is greater than 13 Mbp/sec. some freeze can
be seen during timeshifting on both USB disk and
on external HDD.
Recordings of HD programmes can occupy bigger
size on the USB disk depending on the broadcast’s
resolution. For this reason it is recommended
to use USB hard disk drives for recording HD
programmes.
- 10 -
Do not plug out the USB/HDD during the recording.
This may harm the connected USB/HDD.
Multipartiton support is available. Maximum two
different partitions are supported. If the disk have
more than two partitions, crash may occur. First
partition of the usb disk is used for PVR ready
features. It also must be formatted as primary
partition to be used for PVR ready features.
Some stream packets may not be recorded because
of signal problems, so sometimes video may freezes
during playback.
Record, Play, Pause, Display (for PlayListDialog)
keys could not be used when teletext is ON. If a
recording starts from timer when teletext is ON,
teletext is automatically turned off. Also teletext
usage is disabled when there is ongoing recording
or playback.
• Radio record is not supported.
• The Tv can record programmes up to ten hours.
Connecting the TV to a PC
For displaying your computer’s screen image on your
TV, you can connect your computer to the TV set.
Power off both computer and display before making
any connections. Use a 15-pin D-sub display cable to
connect a PC to the TV. When the connection is made,
switch to PC source. See the Input selection section.
Use a PC audio cable between the audio output of
your PC and the audio input of the TV to enable the
playback of sound through your TV. Set the resolution
that suits your viewing requirements. Resolution
information can be found in the appendix.
PC Input
(back)
Side AV Input
PC VGA Cable
(not supplied)
PC Audio Cable
(not supplied)
Side Audio/Video
Connection Cable
(supplied)
or
SIDE AV
Note: If you connect a PC to the TV using HDMI
connection, radio interference may occur. Therefore
this type of connection is not recommended. You
should use VGA connection instead.
Connecting to a DVD Player
Some DVD players are connected through
COMPONENT SOCKETS (YPbPr). YPbPr can
be used only when you connect a device that has
a YPbPr output through the PC input with YPbPr to
PC cable (YPbPr cable is not supplied).
When the connection is made, switch to YPbPr
source. See, “Input selection” section.
To enable audio connection, use the VGA/
Component Audio cable. First, plug single jack
of the cable to the TV. Afterwards, insert your DVD
player’s audio cable’s connectors into the plural part
of the VGA/Component audio connection cable
(see illustration below). Colours of the connected
jacks should match ( RED & WHITE).
Video Connection
HDMI
inputs
Scart socket
DVD player
YPbPr to PC
cable (optional)
DVD Player
Side AV Input
Audio Cable
(Not supplied)
Side AV
Connection cable
(supplied)
Side AV
To RED & WHITE inputs
Audio Connection
When the connection is made, switch to YPbPr source.
See, Input selection section.
You may also connect through the SCART input.
D I H M 1
SPDIF
Coax.OUT
D I H M 2
Scart Cable
(not supplied)
External device
Note• : These three methods of connection perform the
same function but in different levels of quality. It is not
necessary to connect by all three methods.
- 11 -
Switching On/Off
To Switch the TV On
Connect the power cord to the 220-240V AC, 50
Hz.
To switch the TV on from standby mode either:
Press the standby button on the remote control or
press and hold the side function switch until the TV
goes to standby.
Press the control switch on the left hand side of the
TV. The TV will then switch on.
To Switch the TV Off
Press the ” button on the remote control or hold
the on the TV until shut down, so the TV will switch
to standby mode.
To power down the TV completely, unplug the power
cord from the mains socket.
Note: When the TV is switched to standby mode, the
standby LED can blink to indicate that features such
as Standby Search, Over Air Download or Timer is
active
Input Selection
Once you have connected external systems to
your TV, you can switch to different input sources.
Press SOURCE button on your remote control
consecutively for directly changing sources.
Note: YPbPr mode can be used only when you
connect a device that has a YPbPr output through the
PC input with YPbPr to PC cable (not supplied).
Using Side AV Connectors
You can connect a range of optional equipment to your
TV using the side connectors of the TV.
When connecting a camcorder or camera , you should
use the SIDE AV socket. To do this, you must use the
supplied video/audio connection cable. First, plug
single jack of the cable to the TV’s AV IN socket
(side). Afterwards, insert your camera cable’s (not
supplied) connectors into the plural part of the video/
audio connection cable. Colours of the connected
jacks should match. See illustration below.
Afterwards, you should switch to the Side AV source.
See the section Input selection in the following
sections for more information.
Camera
Side AV Connection
Cable (supplied)
AV Cable
(not supplied)
Headphone
SIDE AV
To listen the TV sound from headphones, you
should connect headphones to your TV by using the
HEADPHONE jack as illustrated above.
Remote Control Handset
Inserting Batteries
Remove the battery cover located on the back of
the handset by gently pulling backwards from the
indicated part.
Insert two AAA/R3 or equivalent type batteries
inside. Observe the correct polarity (+/-) when
inserting batteries and replace the battery cover.
Note: Remove the batteries from the remote control
handset when it is not to be used for a long period.
Otherwise it can be damaged due to any leakage of
batteries. Remote range is approximately 7m/23ft.
(optional)
- 12 -
Basic Operations
You can operate your TV using both the remote
control and onset buttons.
Operation with the Buttons on the TV
Volume Setting
You can use the control switch to change the
volume of the TV. To increase volume, please move
the switch upward. Move the switch downward to
decrease the volume. A volume level scale (slider)
will be displayed on the screen.
Programme Selection
First press the control switch once to change
channel. You can move the switch upward to select
the next programme or move it downward to select
the previous programme.
Viewing Main Menu
The Main Menu screen cannot be displayed by using
the control switch on the TV.
AV Mode
Press the control switch consecutively until the
source OSD is displayed on the screen.
Operation with the Remote Control
The remote control of your TV is designed to control
all the functions of the model you selected. The
functions will be described in accordance with the
menu system of your TV.
Volume Setting
Press V+ button to increase the volume. Press V-
button to decrease the volume. A volume level scale
(slider) will be displayed on the screen.
Programme Selection (Previous or Next
Programme)
Press P- button to select the previous programme.
Press P+ button to select the next programme.
Programme Selection (Direct Access)
Press the numeric buttons on the remote control to
select programmes between 0 and 9. The TV will
switch to the selected programme.
First Time Installation
IMPORTANT: Ensure that the aerial is connected
and a Common Interface module is not inserted
before switching on the TV for the first time
installation.
When the TV is operated for the rst time, the
installation wizard will guide you through the
process. First, the language selection screen will
be displayed:
Use or buttons to select your language
and press OK button to set the selected language
and continue.
After selecting the language, Welcome!screen will
be displayed, requiring you to set Country,Teletext
Language and Scan Encrypted options.
By pressing or button, select the country
you want to set and press button to highlight
Teletext Language option. Use or button
to select desired Teletext Language.
Press button after setting Teletext Language
option. Scan Encrypted will be then highlighted.
You should set the Scan Encrypted as Yes if you
want to scan coded stations.Afterwards select the
desired Teletext Language.
Press OK button on the remote control to continue
and the following message will be displayed on the
screen:
- 13 -
To select the “Yes” or “No” option, highlight the item by
using “ ” or “ ” buttons and press OK button.
Afterwards the following OSD will be displayed on
the screen and the TV will search for both digital and
analogue TV broadcasts.
Note: You can press “MENU” button to cancel.
End of the search process, “Choose Region” osd will
be displayed on the screen (if any multiple region
variants are detected).Please select country and
region choice then press OK to continue.
After all the available stations are stored, Channel
List will be displayed on the screen. If you like the
sort channels, according to the LCN, please select
“Yes” and than press “OK”.
Press OK button to quit channel list and watch TV
Viewing Electronic Programme
Guide (EPG)
You can view the electronic programme guide (EPG)
to see information about available programmes.To
view the EPG menu please press EPG button on the
remote control.
Press “ ”/“ buttons to navigate through channels.
Press ”/“ buttons to navigate through the
programme list.
Please note that event information is updated
automatically. If there is no event information data
available for channels, the EPG will be displayed
with blanks.
EPG Timeline Schedule
Red button (Prev Day): Displays the programmes
of previous day.
Green button (Next day): Displays the programmes
of the next day.
Yellow button (Zoom): Expands programme
information.
Blue button (Filter): Views ltering options.
Numeric buttons (Jump): Jumps to the preferred
channel directly via numeric buttons.
INFO (Details): Displays the programmes in detail.
OK (Options): Views/records or sets timer for future
programmes.
(Search): Displays “Guide Search” menu.
SUBTTL: Press SUBTITLE button to view Select
Genre menu. Using this feature, you can search the
programme guide database in accordance with the
genre. Info available in the programme guide will
be searched and results matching your criteria will
be listed.
SWAP(Now) : Shows the current programme.
(RECORD): the TV will start to record the
selected programme. You can press again to stop
the recording.
- 14 -
EPG Channel Schedule
/ / / : Navigate
Red button (Prev Time Slice): Displays the
programmes of previous time slice.
Green button (Next Time Slice): Displays the
programmes of the next time slice.
Yellow button (Prev Day): Displays the programmes
of previous day.
Blue button (Next day): Displays the programmes
of the next day.
button (Filter): Views ltering options.
Numeric buttons (Jump): Jumps to the preferred
channel directly via numeric buttons.
OK (Options): Views/records or sets timer for future
programmes.
INFO (Details): Displays the programmes in detail.
(RECORD): the TV will start to record the
selected programme. You can press again to stop
the recording.
EPG Now and Next
/ / / : Navigate
OK (Options): Views/records or sets timer for future
programmes.
Blue button (Filter): Views ltering options.
INFO (Event Details): Displays the programmes in
detail.
Green button: Programme schedule will be listed
Yellow button: Display EPG data in accordane with
timeline schedule
(RECORD): the TV will start to record the
selected programme. You can press again to stop
the recording.
Recording via EPG Screen
IMPORTANT: To record a programme, you should
rst connect a USB disk to your TV while the TV is
switched off. You should then switch on the TV to
enable recording feature. Otherwise, recording feature
will not be available.
(RECORD): the TV will start to record the
selected progamme. You can press again to stop
the recording.
Note: Switching to a different broadcast or source is
not available during the recording.
/ : Page left / Page right.
Programme Options
In EPG menu, press the OK button to enter the “Event
Options” menu.
Select Channel
In EPG menu, using this option, you can switch to the
selected channel.
Record / Delete Record Timer
IMPORTANT: To record a programme, you should
rst connect a USB disk to your TV while the TV is
switched off. You should then switch on the TV to
enable recording feature. Otherwise, recording feature
will not be available.
After you have selected a programme in EPG menu,
press the OK button and and Options screen will
be displayed. Select “Recordoption and press the
OK button. After this operation, a recording becomes
set to the selected programme.
To cancel an already set recording, highlight that
programme and press the OK button and select
the option Delete Rec. Timer”. The recording will
be cancelled.
Note: You cannot switch to any other channel or
source while there is an active recording on the
current channel.
Set Timer / Delete Timer
After you have selected a programme in EPG menu,
press the OK button and and Options screen will
be displayed. Select Set Timer on Event option
and press OK button. You can set a timer for future
programmes.
- 15 -
To cancel an already set reminder, highlight that
programme and press the OK button. Then select
Delete Timer” option. The timer will be cancelled.
Note: It is not possible to record or set timer for two or
more individual events at the same time interval.
Installation
Press MENU button on the remote control and
select Installation by using “ ” or “ ” button. Press
OK button and the following menu screen will be
displayed.
Select Automatic Channel Scan (Retune) by using
”/“ button and press OK button. Automatic Channel
Scan (Retune) options will be displayed. You can
select options by using “ ”/“ and OK buttons.
Auto Channel Scan (Retune) Menu
Operation
Analogue: Searches and stores analogue stations.
Digital & Analogue: Searches and stores both
analogue and aerial DVB stations.
Whenever you select an automatic search type and
press OK button, a conrmation screen will appear
on the screen. To start installation process, select
Yes, to cancel select No by using .“ or and
OK button.
After the auto channel scan type is set and selected
and conrmed, the installation process will start and
the progress bar will move along. Press “MENU”
button to cancel process. Located channels are not
stored if the process is cancelled.
Manual Tuning
HINT: This feature can be used for direct broadcast
entry.
Select Manual Channel Scan from the Installation
menu by using ”/“ and OK buttons. Manual
Scan options screen will be displayed.
Select the desired Search Type using or
button. Manual search options will change
accordingly. Use ”/“ button to highlight an item
and then press or button to set an option.
You can press “MENU” button to cancel.
Digital Manual Search
In manual channel scan, the number of the multiplex
or frequency are entered manually and only that
multiplex or frequency are searched for the channels.
After selecting search type as Digital, you can enter
the multiplex or frequency number using the numeric
buttons and press OK button to search.
Analogue Manual Search
After selecting search type as analogue, you can use
”/“ button to highlight an item and then press “
” or “ ” button to set an option.
Enter the channel number or frequency using the
numeric buttons. You can then press OK button
to search. When the channel is located, any new
channels that are not on the list will be stored.
Analogue Fine Tune
Select Analogue Fine Tune from the Installation
menu by using or and OK buttons. The
analogue ne tune screen will be displayed. The
Analogue Fine Tune feature will not be available if
there are no analogue channels, digital channels
and external sources stored.
Press OK button to proceed. Use ” or ” button
to set Fine Tune. When nished, press OK button
again.
- 16 -
Managing Stations: Channel
List
The TV sorts all stored stations in the Channel List.
You can edit this channel list, set favourites or set
active stations to be listed by using the Channel List
options.
Press MENU button to view main menu. Select the
Channel List item by using “ ” or button. Press
OK to view menu contents.
Select Edit Channel List to manage all stored
channels. Use or and OK buttons to select
Edit Channel List.
Operating the Channel List
Press or button to select the channel that
will be processed. Press “ ” or button to select
a function on Channel List menu.
Use P+ or P- buttons to move page up or down.
Press BLUE button to view ltering options.
Press MENU button to exit.
Moving a Channel
First select the desired channel. Select Move option
in the channel list and press the OK button.
Edit Number screen will be displayed. Enter the
desired channel number by using the numeric
buttons on the remote control. If there is a previously
stored channel on that number, a warning screen
will be displayed. Select Yes if you want to move the
channel and press OK.
Press the OK button to process. Selected channel
is now moved.
Deleting a Channel
You can press GREEN button to tag/untag all
channels; YELLOW button to tag/untag channel.
Select the channel that you want to delete and select
Delete option. Press the OK button to continue.
A warning screen will appear. Select YES to
delete, select No to cancel. Press the OK button
to continue.
Renaming a Channel
Select the channel that you want to rename and
select Edit Name option. Press OK button to
continue.
Pressing or button moves to the previous/
next character. Pressing “ or “ button toggles
the current character, i.e., ‘b’ character becomes ‘a’
by and ‘c’ by ”. Pressing the numeric buttons
‘0...9’ replaces the highlighted character with the
characters printed above the button one by one as
the button is pressed.
When nished, press the OK button to save. Press
MENU to cancel.
Locking a Channel
You can press GREEN button to tag/untag all
channels; YELLOW button to tag/untag a single
channel.
Select the channel that you want to lock and select
Lock option. Press OK button to continue.
You will be asked to enter parental control PIN.
Default PIN is set as 0000. Enter the PIN number.
Press OK button when the desired channel is
highlighted to lock/unlock the channel. The Lock
symbol will be displayed next to the selected
channel.
- 17 -
Managing Stations: Favourites
You can create a list of favourite programmes.
Press MENU button to view the main menu. Select
Channel List item by using “ ” or button. Press
OK to view menu contents.
Select Favourites to manage favourite list. Use “
”/“ ” and OK buttons to select Favourites.
You can set various channels as favourites so that
only the favourite channels are navigated.
Select a channel by using “ ” or ” button. Press
OK button to add selected channel to favourites list.
Press OK button again to remove.
Button Functions
OK : Add/remove a station.
YELLOW : Tag/untag a channel.
GREEN : Tag/untag all channels.
BLUE : Displays ltering options.
Managing Stations: Sorting the
Channel List
You can select broadcasts to be listed in the channel
list. To display specic types of broadcast, you should
use the Active channel list setting.
Select Active channel list from the Channel list
menu by using or button. Press OK button
to continue.
You can select a broadcast type option from the list
by using “ ” /“ ” and OK buttons.
On-Screen Information
You can press INFO button to display on-screen
information. Details of the station and current
programme will be displayed on the information
banner.
The information banner gives information on the
channel selected and the programmes on it. The name
of the channel is displayed, along with its channel
list number.
Hint: Not all channels broadcast the programme
data. If the name and time of the programme are
not available, then the information banner will be
displayed with blanks.
If the selected channel is locked, you must enter the
correct four-digit numeric code to view the channel
(default code is 0000). Enter PINwill be displayed
on the screen.
Media Playback Using Media
Browser
If the USB stick is not recognized after power off/on or
First Time Installation, unplug the USB device, turn the
TV off and on again and re-insert the USB device.
To display the Media Browser window, press either
MENUbutton on the remote control and then select
Media Browser by pressing “ ” or “ ” button. Press
OK button to continue. Media Browser menu options
will be displayed.
Also, when you insert USB devices, the media
browser screen will be displayed automatically:
You can play music, picture and video les from the
connected USB memory stick. Use ” or ” button
to select Videos, Photos, Music, Recordings library
or Settings.
- 18 -
Viewing Videos via USB
When you select Videos from the main options, the
available video les will be ltered and listed on this
screen. You can use or button to select a video
le and press OK button to play a video. If you select
a subtitle le and press OK button, you can select or
deselect that subtitle le. The following menu will be
displayed while playing a video le:
Play button): Starts the video playback.
Stop ( button): Stops the video playback.
Pause ( button): Pause the video playback.
Rewind ( button): Goes backward.
Forward ( button): Goes forward.
Subtitle/Audio (LANG. button): Sets subtitle/Audio.
Jump(GREEN button): Jumps to the preferred
channel.
Jump (GREEN button): Jumps to time. Use numeric
buttons to type the desired time and press GREEN
button again to proceed.
Yellow: Opens subtitle time correction menu.
Ret/Back: Back to previous menu.
Press YELLOW button to conm
Press “ button for clear
Press SWAP(Cancel) button to switch back to
previous menu.
Viewing Photos via USB
When you select Photos from the main options,
available image les will be ltered and listed on this
screen.
Jump (Numeric buttons): Jump to selected le using
the numeric buttons.
OK: Views the selected picture in full screen.
/ : Navigate menu
Slideshow ( button): Starts the slideshow using
all images.
GREEN button: Views images in thumbnails.
RED button: Sorts les by date.
Yellow Button: Change viewing style
BLUE: Changes media options.
Slideshow Options
Pause ( button): Pauses the slideshow.
Continue ( button): Continues the slideshow.
Loop/Shufe (GREEN button): Press once to disable
Loop. Press again to disable both Loop and Shufe.
Press once more to enable only Shufe. Press again
to enable all. You can follow the disabled functions
with the change of the icons.
Previous/Next (Left/Right buttons): Jumps to
previous or next le on slideshow.
Rotate (Up/Down buttons): Rotates the image using
up/down buttons.
RETURN (Exit): Back to le list.
INFO: Displays help screen.
- 19 -
Playing Music via USB
When you select Music from the main options,
available audio les will be ltered and listed on this
screen.
/ : Navigate menu
Play ( button): Starts the playback.
Stop ( button): Stops playback.
Pause ( button): Pauses the selected playback.
RED button: Sorts les by Title,Artist or Album.
Loop/Shufe (GREEN button): Press once to disable
Loop. Press again to disable both Loop and Shufe.
Press once more to enable only Shufe. Press again
to enable all. You can follow the disabled functions
with the change of the icons.
Note:
If you start the playback with the button and activate
the symbol, the TV will play the next music/video
le. The playback will proceed accordingly and when
the end of the list is reached, it will be played again
from the beginning (loop function).
If you start the playback with the OK button and
activate the symbol, the same music or video le
will be played in a loop (repeat function).
If you start the playback with or OK button and
activate the symbol, music or video le will be
played in a shufe.
If you start the playback with or OK button and
activate , symbols, music or video le playback
will continue randomly and the random playback will
continue.
0..9 (Numeric buttons): The TV will jump to the
le starting with the letter you input via the numeric
buttons on your remote control.
Play This (OK button): Plays the selected le.
Previous/Next (Left/Right buttons): Jumps to
previous or next le to play.
Yellow Button: Change viewing style
BLUE: Changes media options.
Note: If the Viewing Style is set to Folder in Media
Browser Settings, Music folder will be displayed as
sorted and there is no need to sort les again by
pressing the FAV button.
INFO: Changes lter options.
Recordings Library
IMPORTANT: To view recordings library, you should
rst connect a USB disk to your TV while the TV is
switched off. You should then switch on the TV to
enable recording feature. Otherwise, recording feature
will not be available.
To view the list of recordings, select Recordings
Libraryand press the OK button. Recordings Library
will then be displayed with available recordings.
All the recordings are kept in a list in the recordings
library.
RED button (Delete): Erases the selected
recording.
GREEN button (Edit): Makes changes on the
selected recording.
BLUE button (Sort): Changes the order of the
recordings. You can select from a wide range of
sorting options.
OK button: Activates play options menu:
Play from start: Plays the recording from the
beginning.
• Resume: Recommences the recordings.
• Play from offset: Species a playing point.
Note: Viewing main menu and menu items will not ve
available during the playback.
(Resume): Recommences the recordings.
INFO (Details): Displays the short extended
programmes in detail.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36

Finlux 24F6030 User manual

Category
LCD TVs
Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI