Biostar TA790GXE 128M Owner's manual

TA790GXE 128MSetup Manual

FCC Information and Copyright

This equipment has been tested and found to comply with the limits of a Class

B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. There is no guarantee

that interference will not occur in a particular installation.

The vendor makes no representations or warranties with respect to the

contents here and specially disclaims any implied warranties of merchantability

or fitness for any purpose. Further the vendor reserves the right to revise this

publication and to make changes to the contents here without obligation to

notify any party beforehand.

Duplication of this publication, in part or in whole, is not allowed without first

obtaining the vendor’s approval in writing.

The content of this user’s manual is subject to be changed without notice and

we will not be responsible for any mistakes found in this user’s manual. All the

brand and product names are trademarks of their respective companies.

Table of Contents

Chapter 1: Introduction ............................................................ 1

1.1 Before You Start ................................................................................ 1

1.2 Package Checklist............................................................................. 1

1.3 Motherboard Features...................................................................... 2

1.4 Rear Panel Connectors ..................................................................... 4

1.5 Motherboard Layout......................................................................... 5

Chapter 2: Hardware Installation ............................................. 6

2.1 Installing Central Processing Unit (CPU)....................................... 6

2.2 FAN Headers...................................................................................... 8

2.3 Installing System Memory................................................................ 9

2.4 Connectors and Slots ....................................................................... 11

Chapter 3: Headers & Jumpers Setup ..................................... 16

3.1 How to Setup Jumpers .................................................................... 16

3.2 Detail Settings.................................................................................. 16

Chapter 4: (Hybrid) CrossFireX Function................................ 21

4.1 CrossFireX Requirements................................................................ 21

4.2 CrossFireX Installation .................................................................... 21

4.3 Hybrid CrossFireX Requirements.................................................. 22

4.4 Hybrid CrossFireX Installation....................................................... 22

4.5 Operation Modes Supporting List ................................................. 23

Chapter 5: RAID Functions ..................................................... 24

5.1 Operating System............................................................................ 24

5.2 Raid Arrays ...................................................................................... 24

5.3 How RAID Works............................................................................. 24

Chapter 6: T-Series BIOS & Software ..................................... 28

6.1 T-Series BIOS..................................................................................... 28

6.2 T-Series Software ............................................................................. 36

Chapter 7: Useful Help ............................................................ 46

7.1 Driver Installation Note.................................................................. 46

7.2 Extra Information............................................................................ 47

7.3 AMI BIOS Beep Code....................................................................... 48

7.4 Troubleshooting............................................................................... 49

Appendix: SPEC In Other Languages ...................................... 50

German.................................................................................................................. 50

French .................................................................................................................... 52

Italian..................................................................................................................... 54

Spanish ................................................................................................................... 56

Portuguese ............................................................................................................ 58

Polish...................................................................................................................... 60

Russian ................................................................................................................... 62

Arabic..................................................................................................................... 64

Japanese ................................................................................................................ 66

TA790GXE 128M

1

CHAPTER 1: INTRODUCTION

1.1 B

EFORE YOU START

Thank you for choosing our product. Before you start installing the

motherboard, please make sure you follow the instructions below:

 Prepare a dry and stable working environment with

sufficient lighting.

 Always disconnect the computer from power outlet

before operation.

 Before you take the motherboard out from anti-static

bag, ground yourself properly by touching any safely

grounded appliance, or use grounded wrist strap to

remove the static charge.

 Avoid touching the components on motherboard or the

rear side of the board unless necessary. Hold the board

on the edge, do not try to bend or flex the board.

 Do not leave any unfastened small parts inside the

case after installation. Loose parts will cause short

circuits which may damage the equipment.

 Keep the computer from dangerous area, such as heat

source, humid air and water.

1.2 PACKAGE CHECKLIST

IDE Cable X 1

Serial ATA Cable X 2

Serial ATA Power Cable X 1

Rear I/O Panel for ATX Case X 1

User’s Manual X 1

Fully Setup Driver CD X 1

DCCFX-P2 Paddle Card X 1

FDD Cable X 1 (optional)

USB 2.0 Cable X1 (optional)

S/PDIF out Cable X 1 (optional)

Note: The package contents may be different due to area or your motherboard version.

Motherboard Manual

2

1.3 MOTHERBOARD FEATURES

SPEC

CPU

Socket AM2+ / AM3

AMD Athlon 64 / Athlon 64 FX

/

Athlon 64 x2

/ Sempron / Pheno m / Phenom II pro cessors

AMD 64 Architecture enables 32 and 64 bit

comput ing

Supports Hyper Transport 3.0 and PowerNow

FSB

Support HyperTransport 3.0

Supports up to 5.2 GT/s Bandwidth

Chipset

AMD 790GX

AMD SB750

Super I/O

ITE 8718

Provides the most commonly used legacy

Super I/O functionality.

Low Pin Count Interface

Environment Control init iatives,

H/W Monitor

Fan Speed Contro ller

ITE's "S mart Guardian" funct ion

Main

Memory

DDR2 DIMM Slots x 4

Max Memory Capacity 16GB

Each DIMM supports 256MB/512MB/

1GB/2GB/4GB DDR2

Dual Channel Mode DDR2 memory module

Supports DDR2 533 / 667 / 800

Supports DDR2 1066 (by AM2+ / AM3 CPU)

Registered DIMM and ECC DIMM is not supported

Graphics Radeon HD 3300

Onboard side port memory 128MB DDR2

Max Shared V id eo Memory is 512 MB

DX10/UVD/HDCP support

(Hybrid) CrossFireX support (by ATI driver)

IDE AMD SB750

Ultra DMA 33 / 66 / 100 / 133 Bus Master Mode

supports PIO Mode 0~4,

SATA II AMD SB750

Data transfer rates up to 3 Gb/s.

SATA Version 2.0 s pecificat ion co mp liant.

RAID 0,1,5,1+0 support

LAN Realtek RTL 8111DL

10 / 100 Mb/s / 1Gb/s auto negotiation

Half / Full duplex capability

Sound ALC888

7.1channels audio out

Supports HD Audio

TA790GXE 128M

3

SPEC

PCI Slot x2 Supports PCI expansion cards

PCI Express Gen2 x16 Slot x2 Supports PCI-E Gen2 x16 expansion cards

Slots

PCI Express Gen2 x1 Slot x2 Supports PCI-E Gen2 x1 expansion cards

Floppy Connector x1 Each connector supports 2 Floppy drives

IDE Connector x1 Each connector supports 2 IDE device

SATA Connector x6 Each connector supports 1 SATA devices

Front Panel Connector x1 Supports front panel facilities

Front Audio Connector x1 Supports front panel audio function

CD-in Connector x1 Supports CD audio-in function

S/PDIF out Connector x1 Supports digital audio out function

CPU Fan Header x1 CPU Fan power supply (with Smart Fan function)

System Fan Header x2 System Fan Power supply

CMOS clear Header x1 Restore CMOS data to factory default

USB Connector x3 Each connector supports 2 front panel USB ports

Power Connector (24pin) x1 Connects to Power supply

On Board

Connectors

Power Connector (4pin) x2 Connects to Power supply

Back Panel

I/O

PS/2 Keyboard x1

PS/2 Mouse x1

HDMI port x1

VGA port x1

DVI-D port x1

LAN port x1

USB Port x4

Audio Jack x6

Connects to PS/2 Keyboard

Connects to PS/2 Mouse

Connect to HDTV

Connect to D-SUB monitor

Connect to DVI monitor

Connect to RJ-45 ethernet cable

Connect to USB devices

Provide Audio-In/Out and microphone connection

Board Size 225 mm (W) x 305 mm (L) ATX

OS Support

Windows XP / Vista 32 / Vista 64

Biostar reserves the right to add or remove support

for any OS With or without notice.

Motherboard Manual

4

1.4 REAR PANEL CONNECTORS

X PS/2 Mouse Port Y PS/2 Keyboard Port

Z

HDMI Port

The High-Definition Multimedia Interface (HDMI) is an all-digital audio/video interface

capable of transmitting uncompressed streams to an AV receiver or any compatible digital

audio and/or video monitor, such as a digital television.

[

DVI-D VGA Port

The Digital Visual Interface (DVI) is a video interface transmitting digital video signals to

digital display devices such as flat panel LCDs or digital projectors. The DVI-D connector

allows digital signals transmission only.

\

D-Sub VGA Port

Transmit analog video signals to computer monitor or any other display panels equipped

with D-Sub VGA input.

]

USB 2.0 Port x 4

^

10/100/1000 Mbps LAN Port

_

Audio Jack x 6

Port 2-Channel 4-Channel 6-Channel/8-Channel

Blue Line-In Line- In Line- In

Green Line-Out Front Speaker Out Front Speaker Out

Pink Mic In Mic In Mic In

Orange Center/S ubwoo fer

Black Rear Speaker Out Rear Speaker Out Rear Speaker Out

Grey Side Speaker Out

NOTE: The HDMI and DVI-D ports both can provide digital video signals out-put function, but

these two interfaces cannot work at the same time. The chipset uses the same channel

to control HDMI and DVI-D, so these ports cannot transmit video signal to different display

panels simultaneously.

TA790GXE 128M

5

1.5 MOTHERBOARD LAYOUT

KBMS 1

HDMI1

VGA

DVI

USB1

RJ45USB1

AUDIO2

JUSBV1

JUSBV 2

JCMOS1

AUXPWR1

SYS_FAN1

PEX1_1

PEX16_1

PEX1_2

PCI2

PCI1

PEX16_2

BAT1

LAN

Co de c

F_AUDIO1

SPDIF1

CD_IN1

FDD1

F_USB3 F_USB1F_USB2

PANE L1

SW_PWR

SW_RST

SYS_FA N2

BI O S

Super I/O

SATA1-2

SATA3-4

SATA5-6

IDE1

LED_D1

LED_D2

PH1

PH2

PH3

PH4

ATXPWR2

CPU_FAN1

DIMMA1

DIMMB1

DIMMA2

DIMMB2

Socket AM2+

AMD

790GX

AMD

SB750

ATXPWR1

Note: represents the 1■

st

pin.

Motherboard Manual

6

CHAPTER 2: HARDWARE INSTALLATION

2.1 I

NSTALLING CENTRAL PROCESSING UNIT (CPU)

Step 1: Remove the socket protection cap.

Step 2: Pull the lever toward direction A from the socket and then raise the

lever up to a 90-degree angle.

Step 3: Look for the white triangle on socket, and the gold triangle on

CPU should point towards this white triangle. The CPU will fit only

in the correct orientation.

TA790GXE 128M

7

Step 3: Hold the CPU down firmly, and then close the lever toward direct

B to complete the installation.

Step 4: Put the CPU Fan on the CPU and buckle it. Connect the CPU

FAN power cable to the JCFAN1. This completes the installation.

Motherboard Manual

8

2.2 FAN HEADERS

These fan headers support cooling-fans built in the computer. The fan

cable and connector may be different according to the fan manufacturer.

Connect the fan cable to the connector while matching the black wire to

pin#1.

CPU_FAN1: CPU Fan Header

Assignment

1 Ground

2 +12V

3

FAN RPM rate

sense

41

4 Smart Fan

Control (By Fan)

SYS_FAN1/SYS_FAN2: System Fan Headers

Pin Assignment

1 Ground

2 +12V

SYS_FAN1

SYS_FAN2

13

3

FAN RPM

rate sense

Note:

The CPU_FAN1, SYS_FAN1, and SYS_FAN2 support 4-pin and 3-pin head connectors.

When connecting with wires onto connectors, please note that the red wire is the positive

and should be connected to pin#2, and the black wire is Ground and should be

connected to GND.

TA790GXE 128M

9

2.3 INSTALLING SYSTEM MEMORY

A. DDR2 Modules

DIMMA1

DIMMB1

DIMMA2

DIMMB2

1. Unlock a DIMM slot by pressing the retaining clips outward. Align a

DIMM on the slot such that the notch on the DIMM matches the

break on the Slot.

2. Insert the DIMM vertically and firmly into the slot until the retaining

chip snap back in place and the DIMM is properly seated.

Motherboard Manual

10

B. Memory Capacity

DIMM Socket

Location

DDR2 Module

Total Memory

Size

DIMMA1 256MB/512MB/1GB/2GB/4GB

DIMMB1 256MB/512MB/1GB/2GB/4GB

DIMMA2 256MB/512MB/1GB/2GB/4GB

DIMMB2 256MB/512MB/1GB/2GB/4GB

Max is 16GB.

C. Dual Channel Memory installation

Please refer to the following requirements to activate Dual Channel

function:

Install memory module of the same density in pairs, shown in the table.

Dual Channel Status

DIMMA1

DIMMB1 DIMMA2 DIMMB2

Enabled O O X X

Enabled X X O O

Enabled O O O O

(O means memory installed, X means memory not installed.)

The DRAM bus width of the memory module must be the same (x8 or

x16)

TA790GXE 128M

11

2.4 CONNECTORS AND SLOTS

FDD1: Floppy Disk Connector

The motherboard provides a standard floppy disk connector that supports 360K,

720K, 1.2M, 1.44M and 2.88M floppy disk types. This connector supports the

provided floppy drive ribbon cables.

133

234

IDE1: IDE/ATAPI Connector

The motherboard has a 32-bit Enhanced IDE Controller that provides PIO Mode

0~4, Bus Master, and Ultra DMA 33/66/100/133 functionality.

The IDE connector can connect a master and a slave drive, so you can connect

up to two drives.

139

240

Motherboard Manual

12

SATA1-2/SATA3-4/SATA5-6: Serial ATA Connectors

The motherboard has a PCI to SATA Controller with 6 channels SATA interface,

it satisfies the SATA 2.0 spec and with transfer rate of 3.0Gb/s.

SATA1-2 SATA3-4 SATA5-6

AUXPWR1: Auxiliary Power for Graphics

This connector is an auxiliary power connection for graphics cards. Exclusive

power for the graphics card provides better graphics performance.

Assignment

1 +12V

2 Ground

3 Ground

4 VCC

14

TA790GXE 128M

13

ATXPWR2: ATX Power Source Connector

This connector allows user to connect 24-pin power connector on the ATX

power supply.

1

12

13

24

Pin Assignment Pin Assignment

13 +3.3V 1 +3.3V

14 -12V 2 +3.3V

15 Ground 3 Ground

16 PS_ON 4 +5V

17 Ground 5 Ground

18 Ground 6 +5V

19 Ground 7 Ground

20 NC 8 PW_OK

21 +5V 9 Standby Voltage+5V

22 +5V 10 +12V

23 +5V 11 +12V

24 Ground 12 +3.3V

ATXPWR1: ATX Power Source Connector

Connecting this connector will provide +12V to CPU power circuit.

Assignment

1 +12V

2 +12V

3 Ground

4

1

23

4 Ground

Note:

Before power on the system, please make sure that both ATXPWR1 and ATXPWR2

connectors have been plugged-in.

Motherboard Manual

14

PEX16_1: PCI-Express Gen2 x16 Slot (x16/x8 Speed)

- PCI-Express 2.0 compliant.

- PCI-Express Gen2 supports a raw bit-rate of 5.0Gb/s on the data pins.

- 2X bandwidth over the PCI-Express 1.1 architecture.

- x16 Speed Mode: Maximum theoretical realized bandwidth of 8GB/s

simultaneously per direction, for an aggregate of 16GB/s

totally. (Must be with DCCFX-P2 in PEX16_2)

- x8 Speed Mode: Maximum theoretical realized bandwidth of 4GB/s

simultaneously per direction, for an aggregate of 8GB/s

totally. (Without DCCFX-P2 in PEX16_2 or using

CrossFireX)

- PEX16_1 slot is reserved for graphics or video cards. The design of this

motherboard supports dual PCI-Express graphics cards using CrossFireX

technology with multiple displays. When using CrossFireX, this slot is

master and runs with x8 speed.

- To make this slot run with x16 speed, please insert the Paddle Card

DCCFX-P2 into PEX16_2.

PEX16_2: PCI-Express Gen2 x16 Slot (x8 Speed)

- PCI-Express 2.0 compliant.

- PCI-Express Gen2 supports a raw bit-rate of 5.0Gb/s on the data pins.

- 2X bandwidth over the PCI-Express 1.1 architecture.

- x8 Speed Mode: Maximum theoretical realized bandwidth of 4GB/s

simultaneously per direction, for an aggregate of 8GB/s

totally.

- PEX16_2 slot is reserved for graphics or video cards. The design of this

motherboard supports dual PCI-Express graphics cards using CrossFireX

technology with multiple displays. This slot is slave when using CrossFireX.

- Note: NVIDIA Dual Graphics is not supported

PEX16_1

PEX16_2

TA790GXE 128M

15

PEX1_1/PEX1_2: PCI-Express Gen2 x1 Slots

- PCI-Express 2.0 compliant.

- Data transfer bandwidth up to 500MB/s per direction; 1GB/s in total.

- PCI-Express Gen2 supports a raw bit-rate of 5.0Gb/s on the data pins.

- 2X bandwidth over the PCI-Express 1.1 architecture.

PEX1_1

PEX1_2

PCI1~PCI2: Peripheral Component Interconnect Slots

This motherboard is equipped with 2 standard PCI slots. PCI stands for

Peripheral Component Interconnect, and it is a bus standard for expansion

cards. This PCI slot is designated as 32 bits.

PCI2

PCI1

Motherboard Manual

16

CHAPTER 3: HEADERS & JUMPERS SETUP

3.1 H

OW TO SETUP JUMPERS

The illustration shows how to set up jumpers. When the jumper cap is

placed on pins, the jumper is “close”, if not, that means the jumper is

“open”.

Pin opened Pin closed Pin1-2 closed

3.2 DETAIL SETTINGS

PANEL1: Front Panel Header

This 16-pin connector includes Power-on, Reset, HDD LED, Power LED, and

speaker connection. It allows user to connect the PC case’s front panel switch

functions.

P

W

R

_

L

E

D

R

S

T

H

L

E

D

S

P

K

+

-

1

916

8

O

n

/

O

f

Pin Assignment Function Pin Assignment Function

1 +5V 9 N/A

2 N/A 10 N/A

N/A

3 N/A 1 1 N/A N/A

4 Speaker

Speaker

Connector

12 Power LED (+)

5 HDD LED (+) 13 Power LED (+)

6 HDD LED (-)

Hard drive

LED

14 Power LED (-)

Power LED

7 Ground 15 Power button

8 Reset control

Reset button

16 Ground

Power-on button

TA790GXE 128M

17

JCMOS1: Clear CMOS Header

Placing the jumper on pin2-3 allows user to restore the BIOS safe setting and

the CMOS data. Please carefully follow the procedures to avoid damaging the

motherboard.

13

Pin 1-2 Close:

Normal Operation (Default).

31

13

Pin 2-3 Close:

Clear CMOS data.

※ Clear CMOS Procedures:

1. Remove AC power line.

2. Set the jumper to “Pin 2-3 close”.

3. Wait for five seconds.

4. Set the jumper to “Pin 1-2 close”.

5. Power on the AC.

6. Reset your desired password or clear the CMOS data.

F_USB1~F_USB3: Headers for USB 2.0 Ports at Front Panel

This header allows user to connect additional USB cable on the PC front panel,

and also can be connected with internal USB devices, like USB card reader.

Assignment

1 +5V (fused)

2 +5V (fused)

3 USB-

4 USB-

5 USB+

6 USB+

7 Ground

8 Ground

9 Key

1

2

9

10

F_U SB 3 F _

USB2

USB1

F_

10 NC

Motherboard Manual

18

F_AUDIO1: Front Panel Audio Header

This header allows user to connect the front audio output cable with the PC front

panel. This header allows only HD audio front panel connector; AC’97 connector

is not acceptable.

Assignment

1 Mic Left in

2 Ground

3 Mic Right in

4 GPIO

5 Right line in

6 Jack Sense

7 Front Sense

8 Key

9 Left line in

10 Jack Sense

1

2

9

10

CD_IN1: CD-ROM Audio-in Connector

This connector allows user to connect the audio source from the variaty devices,

like CD-ROM, DVD-ROM, PCI sound card, PCI TV turner card etc.

Assignment

1 Left Channel Input

2 Ground

3 Ground

14

4 Right Channel Input

SPDIF1: Digital Audio-out Connector

This connector allows user to connect the PCI bracket SPDIF output header.

Assignment

1 +5V

2 SPDIF_OUT

13

3 Ground

Page is loading ...

Biostar TA790GXE 128M Owner's manual

Biostar TA790GXE 128M Owner's manual

Related papers

Other documents