ICOM IC-M505 User manual

Category
Two-way radios
Type
User manual

This manual is also suitable for

i
FOREWORD
Thank you for purchasing this Icom product. The IC-M505
VHF MARINE TRANSCEIVER
is designed and built with Icom’s
state of the art technology and craftsmanship. With proper
care, this product should provide you with years of trouble-
free operation.
We want to take a couple of moments of your time to thank
you for making the IC-M505 your radio of choice, and hope
you agree with Icom’s philosophy of “technology first.” Many
hours of research and development went into the design of
your IC-M505.
D
FEATURES
Simple operation with large keys
Easy to hear speaker
Built-in DSC meets ITU Class D requirement
Rugged waterproof construction
Optional COMMANDMIC III™ (HM-162E) is
available
IMPORTANT
READ ALL INSTRUCTIONS carefully and completely
before using the transceiver.
SAVE THIS INSTRUCTION MANUAL — This in-
struction manual contains important operating instructions for
the IC-M505.
EXPLICIT DEFINITIONS
WORD DEFINITION
R WARNING!
CAUTION
NOTE
Personal injury, fire hazard or electric shock
may occur.
Equipment damage may occur.
Recommended for optimum use. No risk of
personal injury, fire or electric shock.
CLEAN THE TRANSCEIVER AND MICROPHONE THOR-
OUGHLY WITH FRESH WATER after exposure to water
including salt, otherwise, the keys and switch may become
inoperable due to salt crystallization.
Icom, Icom Inc. and the logo are registered trademarks of Icom Incor-
porated (Japan) in the United States, the United Kingdom, Germany, France,
Spain, Russia and/or other countries.
COMMANDMIC III is a trademark of Icom Incorporated (Japan) in the United
States.
ii
IN CASE OF EMERGENCY
If your vessel requires assistance, contact other vessels and
the Coast Guard by sending a Distress call on Channel 16.
Or, transmit your Distress call using digital selective calling
on Channel 70.
INSTALLATION NOTE
The installation of this equipment should be made in such a
manner as to respect the EC recommended electromagnetic
field exposure limits (1999/519/EC).
The maximum RF power available from this device is 25
watts. The antenna should be installed as high as possible
for maximum efficiency and that this installation height should
be at least 5 meters above ground (or accessible) level. In the
case where an antenna cannot be installed at a reasonable
height, then the transmitter should neither be continuously
operated for long periods if any person is within 5 meters of
the antenna, nor operated at all if any person is touching the
antenna.
In all cases any possible risk depends on the transmitter
being activated for long periods. (actual recommendation lim-
its are specified as an average of 6 minutes) Normally the
transmitter is not active for long periods of time. Some radio li-
censes will require that a timer circuit automatically cuts the
transmitter after 1–2 minutes etc.
Similarly some types of transmitter, SSB, CW, AM, etc. have a
lower ‘average’ output power and the perceived risk is even
lower.
USING DIGITAL SELECTIVE CALLING (Ch 70)
DISTRESS CALL PROCEDURE
1. While lifting up the key cover, push and hold
[DISTRESS] for 5 sec. until you hear 5 short beeps
change to one long beep.
2. Wait for an acknowledgment on Channel 70 from a coast
station.
After the acknowledgement is received, Channel 16 is auto-
matically selected.
3. Push and hold [PTT], then transmit the appropriate
information as listed above.
USING CHANNEL 16
DISTRESS CALL PROCEDURE
1. “MAYDAY MAYDAY MAYDAY.”
2. “THIS IS ...............” (name of vessel).
3. Say your call sign or other indication of the vessel (AND
9-digit DSC ID if you have one).
4. “LOCATED AT ...............” (your position).
5. State the nature of the distress and assistance required.
6. Give any other information which might facilitate the
rescue.
iii
DOC
CE versions of the IC-M505 which display the
“CE” symbol on the serial number seal, comply
with the essential requirements of the Euro-
pean Radio and Telecommunication Terminal
Directive 1999/5/EC.
This warning symbol indicates that this equip-
ment operates in non-harmonised frequency
bands and/or may be subject to licensing condi-
tions in the country of use. Be sure to check that
you have the correct version of this radio or the
correct programming of this radio, to comply with
national licensing requirement.
DECLARATION
OF CONFORMITY
We Icom Inc. Japan
1-1-32, Kamiminami, Hirano-ku
Osaka 547-0003, Japan
Kind of equipment:
VHF MARINE TRANSCEIVER
This compliances is based on conformity with the following harmonised
standards, specifications or documents:
i)
EN 301 025-2 V1.2.1 (2004-09)
ii)
EN 301 025-3 V1.2.1 (2004-09)
iii) EN 60945 2002
iv) EN 60950-1 2001
v) EN 300 698-2 V1.1.1 ( 2000-08)
vi) EN 300 698-3 V1.1.1 ( 2001-05)
Type-designation: iM505
Signature
Declare on our sole responsibility that this equipment complies with the
essential requirements of the Radio and Telecommunications Terminal
Equipment Directive, 1999/5/EC, and that any applicable Essential Test
Suite measurements have been performed.
Version (where applicable):
0560
Authorized representative name
Place and date of issue
iv
FOREWORD …………………………………………………………… i
IMPORTANT …………………………………………………………… i
EXPLICIT DEFINITIONS ……………………………………………… i
IN CASE OF EMERGENCY…………………………………………… ii
INSTALLATION NOTE ………………………………………………… ii
DOC …………………………………………………………………… iii
TABLE OF CONTENTS ……………………………………………… iv
PRECAUTIONS ………………………………………………………… v
1 OPERATING RULES ……………………………………………… 1
2 PANEL DESCRIPTION ………………………………………… 2–5
Front panel ……………………………………………………… 2
Function display ………………………………………………… 4
Microphone ……………………………………………………… 5
3 BASIC OPERATION…………………………………………… 6–11
Channel selection ……………………………………………… 6
Receiving and transmitting……………………………………… 8
Call channel programming ……………………………………… 9
Channel comments …………………………………………… 10
Microphone Lock function …………………………………… 10
Display backlight ……………………………………………… 10
Optional voice scrambler operation ………………………… 11
4 SCAN OPERATION ………………………………………… 12–13
Scan types ……………………………………………………… 12
Setting TAG channels ………………………………………… 13
Starting a scan ………………………………………………… 13
5 DUALWATCH/TRI-WATCH ……………………………………… 14
Description ……………………………………………………… 14
Operation ……………………………………………………… 14
6 DSC OPERATION …………………………………………… 15–49
MMSI code programming……………………………………… 15
MMSI code check ……………………………………………… 16
DSC address ID………………………………………………… 17
Position and time programming ……………………………… 21
Position and time indication …………………………………… 22
GPS information indication …………………………………… 22
Distress call …………………………………………………… 23
Transmitting DSC calls ………………………………………… 26
Receiving DSC calls …………………………………………… 41
Received messages …………………………………………… 45
DSC Set mode ………………………………………………… 47
7 OTHER FUNCTIONS………………………………………… 50–54
Intercom operation …………………………………………… 50
RX Speaker function …………………………………………… 51
Hailer operation ………………………………………………… 52
Automatic foghorn function …………………………………… 53
8 SET MODE …………………………………………………… 55–57
Set mode programming ……………………………………… 55
Set mode items ………………………………………………… 55
9 CONNECTIONS AND MAINTENANCE …………………… 58–64
Connections …………………………………………………… 58
Antenna ………………………………………………………… 59
Fuse replacement ……………………………………………… 59
Supplied accessories ………………………………………… 59
Microphone hanger …………………………………………… 59
Mounting the transceiver ……………………………………… 60
MB-75 installation ……………………………………………… 61
UT-112/UT-98 installation……………………………………… 62
HM-162E installation…………………………………………… 63
10 TROUBLESHOOTING …………………………………………… 66
11 SPECIFICATIONS AND OPTIONS ……………………… 67–68
Specifications …………………………………………………… 67
Options ………………………………………………………… 68
12 CHANNEL LIST ……………………………………………… 69–70
TEMPLATE
TABLE OF CONTENTS
1
2
3
4
5
6
7
8
9
10
11
12
v
PRECAUTIONS
RWARNING! NEVER connect the transceiver to an AC
outlet. This may pose a fire hazard or result in an electric
shock.
NEVER connect the transceiver to a power source of more
than 16 V DC or use reverse polarity. This will ruin the trans-
ceiver.
NEVER cut the DC power cable between the DC plug at the
back of the transceiver and fuse holder. If an incorrect con-
nection is made after cutting, the transceiver may be dam-
aged.
NEVER place the transceiver where normal operation of the
vessel may be hindered or where it could cause bodily injury.
KEEP the transceiver at least 1 m away from the ship’s nav-
igation compass.
DO NOT use or place the transceiver in areas with temper-
atures below –20°C or above +60°C or, in areas subject to di-
rect sunlight, such as the dashboard.
AVOID the use of chemical agents such as benzine or al-
cohol when cleaning, as they may damage the transceiver
surfaces. If the transceiver becomes dusty or dirty, wipe it
clean with a soft, dry cloth.
BE CAREFUL! The transceiver rear panel will become
hot when operating continuously for long periods.
Place the transceiver in a secure place to avoid inadvertent
use by children.
BE CAREFUL! The transceiver and the optional HM-
162E
COMMANDMIC III
™ employ waterproof construction,
which corresponds to IPX8 of the international standard IEC
60529 (2001). However, once the transceiver or microphone
has been dropped, waterproofing cannot be guaranteed due
to the fact that the case may be cracked, or the waterproof
seal damaged, etc.
1
1
OPERATING RULES
DD
PRIORITIES
Read all rules and regulations pertaining to priorities and
keep an up-to-date copy handy. Safety and Distress calls
take priority over all others.
You must monitor Channel 16 when you are not operating
on another channel.
False or fraudulent distress signals are prohibited and pun-
ishable by law.
DD
PRIVACY
Information overheard but not intended for you cannot law-
fully be used in any way.
Indecent or profane language is prohibited.
DD
RADIO LICENSES
(1) SHIP STATION LICENSE
You must have a current radio station license before using the
transceiver. It is unlawful to operate a ship station which is not
licensed.
Inquire through your dealer or the appropriate government
agency for a Ship-Radiotelephone license application. This
government-issued license states the call sign which is your
craft’s identification for radio purposes.
(2) OPERATOR’S LICENSE
A Restricted Radiotelephone Operator Permit is the license
most often held by small vessel radio operators when a radio
is not required for safety purposes.
The Restricted Radiotelephone Operator Permit must be
posted or kept with the operator. Only a licensed radio opera-
tor may operate a transceiver.
However, non-licensed individuals may talk over a transceiver
if a licensed operator starts, supervises, ends the call and
makes the necessary log entries.
Keep a copy of the current government rules and regulations
handy.
1
2
PANEL DESCRIPTION
2
Front panel
q DISTRESS KEY [DISTRESS]
Push for 5 sec. to transmit a Distress call. (p. 23)
w DSC MENU KEY [MENU]
Push to toggle the DSC menu appear or disappear. (p. 15)
e CLEAR KEY [CLR]
Push to cancel the entered function, exit Set mode.
(pgs. 9, 10, 55)
r HAIL/RX SPEAKER KEY [HAIL•RX ]
Push to turn the hailer mode ON or OFF. (p. 52)
Push and hold for 1 sec. to turn the RX Speaker mode
ON or OFF. (p. 51)
While pushing and holding [H/L], push to turn the auto
foghorn function ON. (p. 54)
t INTERCOM KEY [IC]
Push to activate an optional Intercom function. (p. 50)
Push and hold to call the optional command micro-
phone while in Intercom mode. (p. 50)
y CHANNEL 16/CALL CHANNEL KEY [16•C]
Push to select Channel 16. (p. 6)
Push and hold for 1 sec. to select Call channel. (p. 6)
•“
CCAALLLL
” appears when Call channel is selected.
Push and hold for 3 sec. to enter Call channel program-
ming condition when Call channel is selected. (p. 9)
While pushing and holding [H/L], push to enter the
channel comment programming condition. (p. 10)
Advance the cursor while in the channel comment pro-
gramming condition. (p. 10)
While turning power ON, push to enter Set mode.
(p. 55)
Function display (p. 4)Speaker
q
e
r
t
y
w
uio!0!1
!2
!3
3
2
PANEL DESCRIPTION
u CHANNEL SELECTOR [CHANNEL•ENTER]
Rotate to select the operating channels, Set mode set-
tings, etc. (pgs. 6–8, 55)
While pushing and holding [H/L], rotate to adjust the
brightness of the LCD and key backlight. (p. 10)
Push to enter the input channel comment, selected
item, etc. (pgs. 10, 55)
Rotate to check TAG channels, changes scanning di-
rection or resumes the scan manually during scan.
(p. 13)
While pushing and holding [HAIL•RX ], rotate to ad-
just the audio level in RX Speaker mode. (p. 51)
Push and hold for 1 sec. to display the GPS information
when a GPS receiver is connected. (p. 22)
i DIAL/DUAL/GROUP KEY [DIAL•DUAL/GRP]
Push to select the regular channel. (p. 7)
Push and hold for 1 sec. to start Dualwatch or Tri-watch.
(p. 14)
Push to stop Dualwatch or Tri-watch when either is acti-
vated. (p. 14)
Move the cursor backward while in the channel com-
ment programming condition. (p. 10)
While pushing and holding [H/L], push to select the de-
sired channel group in sequence. (p. 7)
EUR version has International channels only and this func-
tion is not available.
o SQUELCH CONTROL [SQL]
Rotate to set the squelch threshold level. (p. 8)
!0 SCAN/TAG KEY [SCAN•TAG] (p. 13)
Push to start and stop Normal or Priority scan.
Push and hold for 1 sec. to set or clear the displayed
channel as a TAG (scanned) channel.
While pushing and holding [H/L], push for 3 sec. to
clear or set all TAG channels in the selected channel
group.
!1 VOLUME CONTROL [VOL] (p. 8)
Rotate to adjust the audio level.
!2 TRANSMIT POWER KEY [H/L]
Push to toggle the power high or low. (p. 8)
• Some channels are set to low power only.
While pushing this key, some keys perform secondary
functions.
!3 POWER KEY [POWER] (p. 8)
Push to turn power ON.
Push and hold for 1 sec. to turn power OFF.
2
4
2 PANEL DESCRIPTION
Function display
q RX SPEAKER INDICATOR (p. 51)
Appears during the RX Speaker mode.
w POWER INDICATOR (p. 8)
2255WW
” appears when high power is selected.
11WW
” appears when low power is selected.
e TAG CHANNEL INDICATOR (p. 13)
Appears when a TAG channel is selected.
r DUPLEX INDICATOR (p. 7)
Appears when a duplex channel is selected.
t CHANNEL GROUP INDICATOR (p. 7)
Indicates whether an International “
IINNTT
,” U.S.A. “
UUSSAA
,”
DSC “
DDSSCC
” or ATIS “
AATTIISS
” channel is in use. (Depends
on version)
y CALL CHANNEL INDICATOR (pgs. 6, 9)
Appears when the call channel is selected.
u LOW BATTERY INDICATOR
Blinks when the battery voltage drops to approx. 10 V DC
or below.
i CHANNEL NUMBER READOUT
Indicates the selected operating channel number.
o CHANNEL COMMENT INDICATOR
Channel comment appears if programmed. (p. 10)
!0 TIME ZONE INDICATOR
Shows the current time data when a GPS receiver is
connected.
•“
????
” may blink every 2 sec. instead of current time data when
the GPS current time data is invalid.
•“
????
” may blink every 2 sec. instead of current time data 4
hours after the time data is input manually, up until 23.5 hours
have past.
LLooccaall
” appears when the offset time data is set.
(p. 47)
NNoo TTiimmee
” appears when no GPS receiver is con-
nected and no time data is input manually.
BUSY 25W INT CALL
RX DUP
SCRAM TAG
NORMAL SCAN
-34°34.506N
123°23.236W
Local 1:10 CALLING
qwert y
!4
!3
!1
!0
!2
i
o
u
5
2
PANEL DESCRIPTION
2
!1 POSITION INDICATOR
Shows the GPS position data.
•“
????
” may blink every 2 sec. instead of position data when the
GPS position data is invalid. In such a case, the last position
data is held for up to 23.5 hours.
•“
????
” may blink every 2 sec. instead of position data 4 hours
after the position data is input manually, up until 23.5 hours
have past.
NNoo PPoossiittiioonn
” appears when no GPS receiver is
connected and no position data is input manually.
!2 SCAN INDICATOR
PPRRII--SSCCAANN 1166
” appears during Priority scan;
NNOORRMMAALL SSCCAANN
” appears during Normal scan. (p. 13)
DDUUAALL 1166
” appears during Dualwatch; “
TTRRII 1166
” ap-
pears during Tri-watch. (p. 14)
!3 SCRAMBLER INDICATOR (p. 11)
Appears when the voice scrambler function is activated.
(only when the optional scrambler unit is installed.)
!4 BUSY/TRANSMIT INDICATOR (p. 8)
BBUUSSYY
” appears when receiving a signal or when the
squelch opens.
TTXX
” appears while transmitting.
Microphone
q PTT SWITCH [PTT]
Push and hold to transmit; release to receive. (p. 8)
w CHANNEL UP/DOWN KEYS [
YY
]/[
ZZ
]
Push either key to change the operating memory chan-
nel, Set mode settings, etc. (pgs. 6, 7, 55)
Checks TAG channels, changes scanning direction or
resumes the scan manually during scan. (p. 13)
e TRANSMIT POWER KEY [HI/LO]
Toggles power high and low when pushed. (p. 8)
• Some channels are set to low power only.
While pushing and holding [HI/LO], turn power ON to
toggle the Microphone Lock function ON and OFF.
(p. 10)
Microphone
w
q
e
6
BASIC OPERATION
3
Channel selection
ïï
Channel 16
Channel 16 is the distress and safety channel. It is used for
establishing initial contact with a station and for emergency
communications. Channel 16 is monitored during both Dual-
watch and Tri-watch. While standing by, you must monitor
Channel 16.
Push [16•C] momentarily to select Channel 16.
Push [DIAL•DUAL/GRP] to return to the condition before se-
lecting Channel 16, or rotate [CHANNEL] to select an oper-
ating channel.
ïï
Call channel
Each regular channel group has a separate leisure-use call
channel. The call channel is monitored during Tri-watch. The
call channels can be programmed (p. 9) and are used to store
your most often used channel in each channel group for quick
recall.
Push [16•C] for 1 sec. to select the call channel of the se-
lected channel group.
•“
CCAALLLL
” and call channel number appear.
• Each channel group may have an independent call channel after
programming a call channel. (p. 9)
Push [DIAL•DUAL/GRP] to return to the condition before
selecting call channel, or rotate [CHANNEL] to select an
operating channel.
25W25W INTINT CALLCALL
TAGTAG
3434°34.506N34.506N
123123°23.236W23.236W
UTCUTC 1212:00:00 CALLINGCALLING
Push
for 1 sec.
25W INT
TAG
34°34.506N
123°23.236W
UTC 12:00 CALLING
Push
7
3
BASIC OPERATION
3
ïï
International channels
There are pre-programmed 57 international channels for the
IC-M505.
q Push [DIAL•DUAL/GRP] to select a regular channel.
w While pushing and holding [H/L], push [DIAL•DUAL/GRP]
to change the channel group, if necessary.
•“
IINNTT
” appears when International channel is selected.
e Rotate [CHANNEL] to select a channel.
•“
DDUUPP
” appears for duplex channels.
ïï
U.S.A. channels (U.K. version only)
For U.K. version, there are pre-programmed 58 U.S.A. chan-
nels in addition to 57 International channels.
q Push [DIAL•DUAL/GRP] to select a regular channel.
w While pushing and holding [H/L], push [DIAL•DUAL/GRP]
to change the channel group, if necessary.
• International and U.S.A. channels can be selected in sequence.
e Rotate [CHANNEL] to select a channel.
•“
DDUUPP
” appears for duplex channels.
ïï
ATIS and DSC channels
(Holland and FRG versions only)
For Holland and FRG version, there are pre-programmed 57
ATIS and 57 DSC* channels in addition to 57 International
channels.
*FRG version only
q Push [DIAL•DUAL/GRP] to select a regular channel.
w While pushing and holding [H/L], push [DIAL•DUAL/GRP]
to change the channel group, if necessary.
• International, ATIS and DSC channels can be selected in sequence.
e Rotate [CHANNEL] to select a channel.
•“
DDUUPP
” appears for duplex channels.
25W25W DSCDSC
TAGTAG
3434°34.506N34.506N
123123°23.236W23.236W
UTCUTC 1212:00:00 CALLINGCALLING
1W1W ATISATIS
TAGTAG
COMMERCIALCOMMERCIAL
Push +
ATIS channel DSC channel
25W25W USAUSA
DUPDUP
TAGTAG
3434°34.506N34.506N
123123°23.236W23.236W
UTCUTC 1212:00:00 PORTPORT OPROPR
Push +
25W25W INTINT
DUPDUP
TAGTAG
3434°34.506N34.506N
123123°23.236W23.236W
UTCUTC 1212:00:00 PORTPORT OPROPR
Push +
8
3 BASIC OPERATION
Receiving and transmitting
CAUTION: Transmitting without an antenna may dam-
age the transceiver.
q Push [POWER] to turn power ON.
w Set the audio and squelch levels.
Rotate [SQL] fully counterclockwise in advance.
Rotate [VOL] to adjust the audio output level.
Rotate [SQL] clockwise until the noise disappears.
e While pushing and holding [H/L], push [DIAL•DUAL/GRP]
to change the channel group. (p. 7)
r Rotate [CHANNEL] to select the desired channel.
(pgs. 6, 7)
When receiving a signal, “
BBUUSSYY
” appears and audio is emitted
from the speaker.
Further adjustment of [VOL] may be necessary.
t Push [H/L] to select the output power if necessary.
•“
2255WW
” or “
11WW
” appears when high or low power is selected, re-
spectively.
• Choose low power for short range communications, choose high
power for longer distance communications.
• Some channels are for low power only.
y Push and hold [PTT] to transmit, then speak into the mi-
crophone.
•“
TTXX
” appears.
• Channel 70 cannot be used for transmission other than DSC.
u Release [PTT] to receive.
IMPORTANT: To maximize the readability of your trans-
mitted signal, pause a few sec. after pushing [PTT], hold
the microphone 5 to 10 cm from your mouth and speak
into the microphone at a normal voice level.
t
Microphone
q
y
reww
iu
rey
9
3
BASIC OPERATION
3
Call channel programming
You can program the call channel with your most often-used
channels in each channel group for quick recall.
q While pushing and holding
[H/L], push [DIAL•DUAL•
GRP] one or more times to
select the desired channel
group (INT, USA, ATIS or
DSC) to be programmed.
w Push [16•C] for 1 sec. to
select the call channel of
the selected channel group.
•“
CCAALLLL
” and call channel
number appear.
e Push [16•C] again for 3 sec.
(until a long beep changes
to 2 short beeps) to enter
call channel programming.
Channel number starts blink-
ing.
r Rotate [CHANNEL] to se-
lect the desired channel.
t Push [16•C] to program the
displayed channel as the
call channel.
Push [CLR] to cancel.
The channel number stops
blinking.
25W25W INTINT
DUPDUP
TAGTAG
3434°34.506N34.506N
123123°23.236W23.236W
UTCUTC 1212:00:00 INTLINTL
25W25W INTINT CALLCALL
TAGTAG
3434°34.506N34.506N
123123°23.236W23.236W
UTCUTC 1212:00:00 CALLINGCALLING
25W25W INTINT CALLCALL
TAGTAG
3434°34.506N34.506N
123123°23.236W23.236W
UTCUTC 1212:00:00 CALLINGCALLING
25W25W INTINT CALLCALL
DUPDUP
TAGTAG
3434°34.506N34.506N
123123°23.236W23.236W
UTCUTC 1212:00:00 INTLINTL
25W25W INTINT CALLCALL
DUPDUP
TAGTAG
3434°34.506N34.506N
123123°23.236W23.236W
UTCUTC 1212:00:00 INTLINTL
10
3 BASIC OPERATION
Channel comments
Memory channels can be labelled with a unique alphanumeric
ID of up to 10 characters.
Capital letters, small letters, 0 to 9, some symbols (/ . –) and
space can be used.
q Select the desired channel.
Cancel Dualwatch, Tri-watch or Scan in advance.
w While pushing and holding [H/L], push [16•C] to edit the
channel comment.
A cursor and the first char-
acter start blinking alter-
nately.
e Select the desired charac-
ter by rotating [CHAN-
NEL].
• Push [16•C] or [DIAL•DUAL/GRP] to move the cursor forward
or backward, respectively.
r Repeat step e to input all characters.
t Push [CHANNEL•ENTER] to input and set the comment.
Push [CLR] to cancel.
• The cursor and the character stop blinking.
y Repeat steps q to t to program other channel com-
ments, if desired.
Microphone Lock function
The Microphone Lock function electrically locks [Y]/[Z] and
[HI/LO] keys on the supplied microphone. This prevents ac-
cidental channel changes and function access.
While pushing and holding [HI/LO] on the microphone, turn
power ON to toggle the Lock function ON and OFF.
Display backlight
The function display and keys can be backlit for better visibil-
ity under low light conditions.
While pushing and holding [H/L], rotate [CHANNEL] to ad-
just the brightness of the LCD and key backlight.
The backlight is adjustable in 7 levels and OFF.
[HI/LO]
[Y]/[Z]
25W25W INTINT
TAGTAG
3434°34.506N34.506N
123123°23.236W23.236W
UTCUTC 1212:00:00PLEASURE__PLEASURE__
11
3
BASIC OPERATION
3
Optional voice scrambler operation
DD
Activating the scrambler
The optional voice scrambler provides private communica-
tions. In order to receive or send scrambled transmissions
you must first activate the scrambler function. To activate the
function, an optional scrambler unit is necessary. See pgs.
57, 62 for setting the scrambler unit. Ask your dealer for de-
tails.
The scrambler function automatically turns OFF when
Channel 16 or 70 is selected.
q Rotate [CHANNEL] to select an operating channel other
than Channel 16 and 70.
w While pushing and holding [H/L], push [IC] to turn the op-
tional scrambler function ON.
•“
SSCCRRAAMM
” appears.
e To turn the scrambler function OFF, repeat step w.
•“
SSCCRRAAMM
” disappears.
DD
Programming scrambler codes
There are 32 codes (1 to 32) or 128 codes (0 to 127)* avail-
able for programming when an optional scrambler unit is in-
stalled. In order to understand one another, all transceivers
in your group must have the same scramble code. This func-
tion may not be available depending on dealer setting.
*Depends on the installed scrambler unit.
q Turn power OFF.
w While pushing [16C], turn power ON to enter set mode.
e After the display appears, release [16C].
r Rotate [CHANNEL] to select the “
SSccrraammbblleerr CCooddee
,”
push [CHANNELENTER].
t Rotate [CHANNEL] to select the desired scrambler code.
y Push [CHANNELENTER] to set and exit the scrambler
code item.
u Push [CLR], or rotate [CHANNEL] to select “
EExxiitt
,” push
[CHANNELENTER] to exit set mode.
--Set Mode--
Scrambler Code
˘5
4
3
2
1
<ENT˘OK>
--Set Mode--
Dual/Tri
Beep
Contrast
Foghorn Frequency
Radio Power
Scrambler Type
˘Scrambler Code
--Set Mode--
˘Scan Type
Scan Timer
Dual/Tri
Beep
Contrast
Foghorn Frequency
Radio Power
+
to enter set mode.
Push
to select code,
then push.
Rotate
to select item,
then push.
Rotate
Select
Select
[Example]: Programming scrambler code 5.
12
SCAN OPERATION
4
Scan types
Scanning is an efficient way to locate signals quickly over a
wide frequency range. The transceiver has Priority scan and
Normal scan.
Set the TAG channels (scanned channel) before scanning.
Clear the TAG channels which inconveniently stop scanning,
such as those for digital communication use. (Refer to right
page for details.)
Choose Priority or Normal scan in Set mode. (p. 55)
PRIORITY SCAN
Priority scan searches through all TAG channels in se-
quence while monitoring Channel 16. When a signal is de-
tected on Channel 16, scan pauses until the signal disap-
pears; when a signal is detected on a channel other than
Channel 16, scan becomes Dualwatch until the signal dis-
appears.
CH 06
CH 01
CH 16
CH 02
CH 05 CH 04
CH 03
NORMAL SCAN
Normal scan, like Priority scan, searches through all TAG
channels in sequence. However, unlike Priority scan,
Channel 16 is not checked unless Channel 16 is set as a
TAG channel.
CH 01 CH 02
CH 06
CH 05 CH 04
CH 03
13
4
SCAN OPERATION
4
Setting TAG channels
For more efficient scanning, add the desired channels as TAG
channels or clear the TAG for unwanted channels.
Channels that are not tagged will be skipped during scanning.
TAG channels can be assigned to each channel group (INT,
USA, ATIS or DSC) independently.
q While pushing and holding [H/L], push [DIALDUAL/GRP]
to select the desired channel group (INT, USA, ATIS or
DSC.)
w Select the desired channel to be set as a TAG channel.
e Push [SCANTAG] for 1 sec. to set the displayed channel
as a TAG channel.
•“
TTAAGG
” appears in the display.
r To cancel the TAG channel setting, repeat step e.
•“
TTAAGG
” disappears.
Clearing (or setting) all tagged channels
While pushing and holding [H/L], push [SCANTAG] for 3
sec. (until a long beep changes to 2 short beeps) to clear all
TAG channels setting in the channel group.
• Repeat above procedure to set all TAG channels.
Starting a scan
Set scan type (Priority or Normal scan) and scan resume
timer in advance, using Set mode. (p. 55)
q While pushing and holding [H/L], push [DIALDUAL/GRP]
to select the desired channel group (INT, USA, ATIS or
DSC) if desired.
w Set TAG channels as described at left.
e Make sure the squelch is closed to start a scan.
r Push [SCANTAG] to start Priority or Normal scan.
•“
PPRRII--SSCCAANN 1166
” appears at the channel comment indicator
during Priority scan.
•“
NNOORRMMAALL SSCCAANN
” appears at the channel comment indicator
during Normal scan.
When a signal is detected, scan pauses until the signal disap-
pears or resumes after pausing 5 sec. according to Set mode
setting. (Channel 16 is still monitored during Priority scan.)
Rotate [CHANNEL] to check the scanning TAG channels, to
change the scanning direction or resume the scan manually.
• A beep tone sounds and “
1166
” blinks at the channel comment in-
dicator when a signal is received on Channel 16 during Priority
scan.
Push
Scan starts. When a signal is received
BUSYBUSY 25W25W INTINT
TAGTAG
NORMALNORMAL SCANSCAN
3434°34.506N34.506N
123123°23.236W23.236W
UTCUTC 1212:00:00 SAFETYSAFETY
25W25W INTINT
DUPDUP
TAGTAG
NORMALNORMAL SCANSCAN
3434°34.506N34.506N
123123°23.236W23.236W
UTCUTC 1212:00:00
25W25W INTINT
DUPDUP
TAGTAG
3434°34.506N34.506N
123123°23.236W23.236W
UTCUTC 1212:00:00 INTLINTL
[Example]: Starting a normal scan.
14
DUALWATCH/TRI-WATCH
5
Description
Dualwatch monitors Channel 16 while you are receiving
on another channel; Tri-watch monitors Channel 16 and the
call channel while receiving another channel. Dualwatch/Tri-
watch is convenient for monitoring Channel 16 when you are
operating on another channel.
Operation
q Select Dualwatch or Tri-watch in Set mode. (p. 56)
w Rotate [CHANNEL] to select the desired operating channel.
e Push [DIALDUAL/GRP] for 1 sec. to start Dualwatch or
Tri-watch.
•“
DDUUAALL 1166
” appears during Dualwatch; “
TTRRII 1166
” appears dur-
ing Tri-watch.
• A beep tone sounds when a signal is received on Channel 16.
r To cancel Dualwatch/Tri-watch, push [DIALDUAL/GRP]
again.
DUALWATCH/TRI-WATCH SIMULATION
• If a signal is received on Channel 16, Dualwatch/Tri-watch
pauses on Channel 16 until the signal disappears.
• If a signal is received on the call channel during Tri-watch,
Tri-watch becomes Dualwatch until the signal disappears.
• To transmit on the selected channel during Dualwatch/Tri-
watch, push and hold [PTT].
[Example]: Operating Tri-watch on INT Channel 25
25W25W INTINT
DUPDUP
TAGTAG
TRITRI 1616
3434°34.506N34.506N
123123°23.236W23.236W
UTCUTC 1212:00:00 TELEPHONETELEPHONE
BUSYBUSY 25W25W INTINT CALLCALL
DUPDUP
TAGTAG
TRITRI 1616
3434°34.506N34.506N
123123°23.236W23.236W
UTCUTC 1212:00:00 INTLINTL
Tri-watch starts. Signal is received on call
channel.
BUSYBUSY 25W25W INTINT
DUPDUP
TAGTAG
TRITRI 1616
3434°34.506N34.506N
123123°23.236W23.236W
UTCUTC 1212:00:00 TELEPHONETELEPHONE
Signal received on Channel
16 takes priority.
25W25W INTINT
DUPDUP
TAGTAG
TRITRI 1616
3434°34.506N34.506N
123123°23.236W23.236W
UTCUTC 1212:00:00 TELEPHONETELEPHONE
Tri-watch resumes after the
signal disappears.
15
6
DSC OPERATION
5
6
MMSI code programming
The 9-digit MMSI (Maritime Mobile Service Identity: DSC self
ID) code can be programmed at power ON.
This code programming can be performed only once.
q Turn power OFF.
w While pushing [MENU], turn power ON to enter MMSI
code programming condition.
e After the display appears, release [MENU].
r Push [MENU] again to enter the DSC menu.
t Rotate [CHANNEL] to select “
SSeett uupp
,” push [CHAN-
NELENTER].
y Rotate [CHANNEL] to select “
MMMMSSII CChheecckk
,” push
[CHANNELENTER].
u Rotate [CHANNEL]
to set
the specific 9-digit MMSI code.
• Push [16C] or [DIALDUAL/GRP] to move the cursor forward
or backward, respectively.
• Push [CLR] to cancel and return to the set up menu.
i After entering the 9-digit code, push [CHANNELENTER]
to set the code.
• Returns to the set up menu.
o Push [CLR] or rotate [CHANNEL] to select “
EExxiitt
,” push
[CHANNELENTER].
• Returns to the DSC menu.
• Repeat again to return to the normal operation condition.
--DSC--DSC Menu--Menu--
MMSI CheckMMSI Check
__________________
<CLR<CLR˘ExitExit / ENTENT˘OK>OK>
--DSC--DSC Menu--Menu--
SetSet upup
Add:INDVAdd:INDV IDID
Add:GroupAdd:Group IDID
DEL:INDVDEL:INDV IDID
DEL:GroupDEL:Group IDID
OffsetOffset TimeTime
˘MMSIMMSI CheckCheck
--DSC--DSC Menu--Menu--
SelectSelect ItemItem
PositionPosition InputInput
ReceivedReceived CallsCalls
˘SetSet upup
ExitExit
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80

ICOM IC-M505 User manual

Category
Two-way radios
Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI