Intel HS-2601A User manual

HS-2601A

Intel Low Power Mobile 500MHz

Mini Board Computer

•3.5” Size•All-in-One•CRT/Panel•LAN•WDT•

•

DOC

•

2 USB

•

IrDA

•

PC/104

•

Flash Disk

•

•PCI Bus Mini Board•

C

o

p

y

r

i

g

h

t

D

i

s

c

l

a

i

m

e

r

s

The accuracy of contents in this manual has passed thorough checking and review

before publishing. BOSER Technology Co., Ltd., the manufacturer and publisher, is

not liable for any infringements of patents or other rights resulting from its use. The

manufacturer will not be responsible for any direct, indirect, special, incidental

or consequential damages arising from the use of this product or

documentation, even if advised of the possibility of such damage(s).

This manual is copyrighted and BOSER Technology Co., Ltd. reserves all

documentation rights. Unauthorized reproduction, transmission, translation,

and storage of any form and means (i.e.,

electronic, mechanical, photocopying,

recording) of this document, in whole or partly, is prohibited, unless granted

permission by BOSER Technology Co., Ltd.

BOSER Technology Co., Ltd.

reserves the right to change or improve the

contents of this document without due notice.

BOSER Technology Co., Ltd.

assumes no responsibility for any errors or omissions that may appear in this

manual, nor does it make any commitment to update the information contained

herein.

T

r

a

d

e

m

a

r

k

s

BOSER is a registered trademark of BOSER Technology Co., Ltd.

ISB is a registered trademark of BOSER Technology Co., Ltd.

Intel is a registered trademark of Intel Corporation.

Award is a registered trademark of Award Software, Inc.

All other trademarks, products and or product names mentioned herein are

mentioned for identification purposes only, and may be trademarks and/or

registered trademarks of their respective companies or owners.

Edition 1.2, June 28, 2003

Table of Contents

Chapter 1 General Description ---------------------------------6

1.1

Major Features ------------------------------------------------------ 2

1.2

Specifications ------------------------------------------------------- 3

1.3

Board Dimensions ------------------------------------------------- 4

Chapter 2 Unpacking ---------------------------------------------5

2.1

Opening the Delivery Package --------------------------------- 5

2.2

Inspection------------------------------------------------------------- 5

Chapter 3 Hardware Installation-------------------------------7

3.1

Before Installation-------------------------------------------------- 7

3.2

Board Layout -------------------------------------------------------- 8

3.3

Jumper List----------------------------------------------------------- 9

3.4

Connector List ------------------------------------------------------ 9

3.5

Configuring the CPU ---------------------------------------------- 9

3.6

System Memory--------------------------------------------------- 10

3.7

DiskOnChip



Address Setting ------------------------------ 10

3.7.1

Installing DiskOnChip



Modules------------------------------- 10

3.7.1

Removing DiskOnChip



Modules -------------------------------11

3.8

VGA Controller ---------------------------------------------------- 12

JP2: Panel Voltage Select --------------------------12

CN6: 15-pin CRT Connector (DB15) ---------------12

CN10: 50-pin Panel Connector --------------------13

3.9

IDE Drive Connector--------------------------------------------- 14

CN12: Primary IDE Connector ---------------------14

3.10

Floppy Disk Drive Connector--------------------------------- 15

CN11: FDD Connector ------------------------------15

3.11

Serial Port Connectors ----------------------------------------- 16

CN15 and CN14: COM1/COM2 Connector

(5x2 Header) ----------------------------------------16

3.12

Parallel Connector ----------------------------------------------- 16

CN16: Parallel Connector --------------------------16

3.13

Ethernet Connector---------------------------------------------- 17

CN4: RJ-45 and LAN LED Connector --------------17

3.14

IrDA Connector --------------------------------------------------- 17

CN9: IrDA Connector -------------------------------17

3.15

USB Connector --------------------------------------------------- 18

CN13: USB Connector ------------------------------18

3.16

CMOS Data Clear ------------------------------------------------- 18

JP4: Clear CMOS------------------------------------18

3.17

Power Connectors ----------------------------------------------- 18

CN1: 4-pin Power Connector ----------------------18

CN5: 2-pin Power Input Connector----------------19

3.18

Keyboard/Mouse Connectors -------------------------------- 19

CN8: 6-pin Keyboard/Mouse Connector ---------19

CN7: PS/2 6-pin Mini DIN Keyboard/Mouse

Connector-------------------------------------------19

3.19

System Front Panel Connectors ---------------------------- 19

LD2: IDE LED Connector ----------------------------19

LD1: Power LED --------------------------------------20

JP3: Reset Button Connector-----------------------20

3.20

Watchdog Timer -------------------------------------------------- 20

JP1: Watchdog Timer Active Type Setting -------20

3.21

CompactFlash



Connector ----------------------------------- 22

3.22

Mini PCI Connector ---------------------------------------------- 23

PC1: Mini PCI Connector Pin Information ---------23

3.23

PC/104 Connectors ---------------------------------------------- 25

CN3: 40-pin PC/104 Expansion Slot ---------------25

CN2: 64-pin PC/104 Expansion Slot ---------------26

Chapter 4 Award BIOS Setup -------------------------------- 27

4.1

Starting Setup ----------------------------------------------------- 27

4.2

Using Setup -------------------------------------------------------- 28

4.2.1

Getting Help-----------------------------------------------------------28

4.3

Main Menu ---------------------------------------------------------- 29

4.4

Standard CMOS Setup------------------------------------------ 31

4.5

BIOS Features Setup -------------------------------------------- 34

4.6

Chipset Features Setup ---------------------------------------- 39

4.7

Power Management Setup ------------------------------------ 43

4.7.1

PM Timers -------------------------------------------------------------45

4.7.2

Reload Global Timer Events --------------------------------------46

4.8

PNP/PCI Configuration ----------------------------------------- 47

4.9

Load BIOS Defaults---------------------------------------------- 48

4.10

Load Setup Defaults--------------------------------------------- 49

4.11

Integrated Peripherals ------------------------------------------ 50

4.12

Supervisor/User Password Setting------------------------- 53

4.13

IDE HDD Auto Detection --------------------------------------- 54

4.14

Save & Exit Setup ------------------------------------------------ 55

4.15

Exit Without Saving---------------------------------------------- 56

Chapter 5 Software Utilities ----------------------------------- 57

5.1

VGA Driver Installation for Win 95/98---------------------- 57

5.2

VGA Driver Installation for Win NT4.0 --------------------- 59

5.3

LAN Driver Installation for WIN95 & WIN98-------------- 62

5.3.1 Win98-------------------------------------------------------------------62

5.3.2 Win95-------------------------------------------------------------------62

5.4

LAN Driver Installation for Win NT4.0 --------------------- 64

S

a

f

e

t

y

I

n

s

t

r

u

c

t

i

o

n

s

Integrated circuits on computer boards are sensitive to static electricity.

To avoid damaging chips from electrostatic discharge, observe the

following precautions:



Do not remove boards or integrated circuits from their anti-static

packaging until you are ready to install them.

 Before handling a board or integrated circuit, touch an unpainted portion

of the system unit chassis for a few seconds. This helps to discharge any

static electricity on your body.



Wear a wrist-grounding strap, available from most electronic component

stores, when handling boards and components. Fasten the ALLIGATOR

clip of the strap to the end of the shielded wire lead from a grounded

object. Please wear and connect the strap before handle the HS-2601A

to ensure harmlessly discharge any static electricity through the strap.



Please use an anti-static pad when putting down any components or

parts or tools outside the computer. You may also use an anti-static bag

instead of the pad. Please inquire from your local supplier for additional

assistance in finding the necessary anti-static gadgets.

NOTE:

DO NOT TOUCH THE BOARD OR ANY OTHER SENSITIVE

COMPONENTS WITHOUT ALL NECESSARY ANTI-STATIC

ROTECTION.

This page intentionally left blank.

1

Chapter 1

General Description

The HS-2601A is a 100MHz Intel

®

BX chipset-based Mini PCI Bus Intel

Mobile board. With features such as enhanced I/O effects with

CRT/VGA, and LAN all combined, the HS-2601A is an ideal all-in-one

compact-size board for the demanding embedded applications and IA

platforms.

Its onboard DMA33 to IDE drive interface architecture allows the

HS-2601A to support data transfers of 33MB/sec with a maximum of

two IDE drives. Its Intel

®

BX chipset design makes it possible for the

board to support most Intel Mobile microprocessors in the market, The

C&T 69000 CRT/Panel display controller offers an on-chip 2MB

memory that supports up to 1280x1024x256 colors display resolution.

For suitable installation into any size system with 8/16/32bit ISA and/or

PCI slots operation, the board’s advanced PISA bus add-on feature

allows user to easily obtain both ISA's 16bit and PCI's 32bit full set

signals from a half size PISA slot. System memory is also sufficient

with the two DIMM sockets that can support up to 256MB.

Additional onboard connectors include an advanced USB and IrDA

ports providing faster data transmission, a DOS-compatible

DiskOnChip



socket with a maximum capacity of 288MB, and one

external RJ45 connector for 10/100 Base-TX Ethernet use.

2

To ensure the reliability in an unmanned or standalone system

, the

Watchdog Timer (WDT) onboard HS-2601A is designed with pure

hardware that does not need the arithmetical functions of a real-time

clock chip. If any program causes unexpected halts to the system, the

onboard Watchdog Timer (WDT) will automatically reset the CPU or

generate an interrupt to resolve such condition.

1.1 Major Features

The HS-2601A comes with the following features:

 BGA Packaged Intel



Low Power Mobile CPU at 500MHz, 700MHz, and

800MHz

 One SO-DIMM socket with a maximum capacity of 256MB

 Fast PCI DMA33 controller supporting two IDE disk drives

 Mini PCI Local Bus support

 Two RS-232 serial ports

 PS/2 Keyboard and PS/2 Mouse connectors

 One enhanced bi-directional parallel port supporting SPP/ECP/EPP

modes

 Winbond W83977 super I/O chipset

 C&T 69000 CRT/Panel display controller

 Intel



82559 100 Base-TX LAN controller

 DiskOnChip



memory size up to 288MB

 PC/104 Bus connector

 Optional 8~64MB Flash Disk support

3

1.2 Specifications



CPU: Intel



Low Power Mobil CPU from 500-800 MHz



Bus Interface: Mini PCI Local Bus



Memory: One SO-DIMM socket supporting up to 256MB



Chipset: Intel



82443BX



I/O Chipset: Winbond W83977



VGA: C&T 69000 with 2MB memory supporting CRT/Panel displays up

to 1280 x1024 at 256 colors

 IDE: Two IDE disk drives supporting ATA/33 and with a transfer rate up

to 33MB/sec



Flash Disk: 8~64 MB IDE interface Flash Disk support (optional)



FDD: Supports up to two floppy disk drives



Parallel: One enhanced bi-dirctional parallel port supporting

SPP/ECP/EPP

 LAN: Intel



82559 100 Base-TX LAN

 Serial Port: Two RS-232 serial ports include 16C550 UART with 16byte

FIFO



IrDA: One IrDA TX/RX header



USB: Two USB ports



CompactFlash: One optional CompactFlash adapter slot on solder

side

 Keyboard/Mouse: PS/2 6-pin Mini DIN or 6-pin connector

 DiskOnChip



: Socket for DiskOnChip and memory size up to 288MB

 BIOS: Award PnP Flash BIOS

 Watchdog Timer: Sets 1, 2, 10, 20, 110, 220 seconds activity trigger

with Reset or NMI



CMOS: Battery backup



DMA Channels: 7



Interrupt Levels: 15



PC/104: PC/104 connector for 16bit ISA Bus



Main Power: Single +5V power input



Extra Power: One 4-pin +12V/-12V connector



Max. Power Consumption: +5V@6A



Operating Temperature: 0~60

o

C



Board Size: 10.3 x 14.6 cm

4

1.3 Board Dimensions

5

Chapter 2

Unpacking

2.1 Opening the Delivery Package

The HS-2601A is packed in an anti-static bag. The board has

components that are easily damaged by static electricity. Do not

remove the anti-static wrapping until proper precautions have been

taken. Safety Instructions in front of this manual describe anti-static

precautions and procedures.

2.2 Inspection

After unpacking the board, place it on a raised surface and carefully

inspect the board for any damage that might have occurred during

shipment. Ground the board and exercise extreme care to prevent

damage to the board from static electricity.

Integrated circuits will sometimes come out of their sockets during

shipment. Examine all integrated circuits, particularly the BIOS,

processor, memory modules, ROM-Disk, and keyboard controller chip

to ensure that they are firmly seated. The HS-2601A delivery package

contains the following items:

 HS-2601A Industrial Single Board

 Printer Ports Flat Cable x 1

 COM port Flat Cable x 1

 IDE port Flat Cable x 1

 FDD port Flat Cable x 1



PS/2 Keyboard/Mouse Transfer Cable x 1

 Utility Disc

 User’s Manual

6

It is recommended that you keep all the parts of the delivery package

intact and store them in a safe/dry place for any unforeseen event

requiring the return shipment of the product. In case you discover any

missing and/or damaged items from the list of items, please contact

your dealer immediately.

7

Chapter 3

Hardware Installation

This chapter provides the information on how to install the hardware

using the HS-2601A. This chapter also contains information related to

jumper settings of switch, watchdog timer, and the DiskOnChip



address selection etc.

3.1 Before Installation

After confirming your package contents, you are now ready to install

your hardware. The following are important reminders and steps to

take before you begin with your installation process.

1. Make sure that all jumper settings match their default settings

and CMOS setup correctly. Refer to the sections on this chapter

for the default settings of each jumper.

2. Go through the connections of all external devices and make

sure that they are installed properly and configured correctly

within the CMOS setup. Refer to the sections on this chapter

for the detailed information on the connectors.

3. Keep the manual and diskette in good condition for future

reference and use.

8

3.2 Board Layout

9

3.3 Jumper List

Jumper Definition Default Page

JP1 Watchdog Timer Active Type Select Short 2-3 20

JP2 Panel Voltage Select Short 1-2 12

JP4 Clear CMOS Short 1-2 18

3.4 Connector List

Connector Definition Page

JP3 Reset Button 20

CN1 4-pin Power In Connector 18

CN2 PC/104 64-pin Connector 26

CN3

PC104 40-pin Connector 25

CN4 RJ45 and LAN LED Connector 17

CN5 2-pin Power In Connector 18

CN6 CRT Connector 12

CN7 PS/2 6-pin Mini Din KB/Mouse Connector 19

CN8 6-pin Keyboard/Mouse Connector 19

CN9 IrDA Connector 17

CN10 Panel Connector 13

CN11 Floppy Connector 15

CN12 IDE Connector 14

CN13 USB Connector 18

CN14 COM2 Connector (5x2 Header) 16

CN15

COM1 Connector (5x2 Header) 16

CN16 Parallel Connector 16

CN17 CompactFlash Connector 22

LD1 Power LED Connector 19

LD2 HDD LED Connector 19

PC1 Mini PCI Connector 23

U2 SO-DIMM Socket 10

U7 DiskOnChip Socket 10

3.5 Configuring the CPU

The HS-2601A, with its onboard BGA processor, auto-detects the

features of the mounted microprocessor onboard. The HS-2601A

automatically identifies the frequency and clock speed of the installed

microprocessor chip, thereby eliminating the need for user to do

additional CPU configuration or hardware settings related to it.

10

3.6 System Memory

The HS-2601A provides one SO-DIMM socket at location U2. This

onboard memory socket can support 64MB, 128MB and 256MB

SO-DIMM modules. The system’s maximum memory capacity is

256MB.

143

144 2

1

144-pin SO-DIMM Socket

pin orientation

NOTE:

SO-DIMM sockets out on the market these days have very fragile

contacts that attach to modules. We highly recommend you not to

regularly remove the installed SO-DIMM from its socket. Doing so

may wear out the contact between the socket and module.

3.7 DiskOnChip



Address Setting

The DiskOnChip function allows the system to boot or operate

without a FDD or a HDD. DiskOnChip



modules may be formatted as

drive C or A. With DiskOnChip, user may also execute DOS

commands such as FORMAT, SYS, COPY, XCOPY, DISCOPY and

DISKCOMP etc.

The U7 location onboard the HS-2601A is the DiskOnChip



module

socket. The board circuitry assigns a LOCKED starting memory

address of the installed module at D000. If you have another memory

device that has a similar memory capacity with that of the DOC in your

system, please set both at different memory address mapping to avoid

the mapping area conflicts. Failing to do so will not make the HS-2601A

and the additional memory device function properly.

3.7.1 Installing DiskOnChip



Modules

When installing a DiskOnChip module onto your board, please take

note of the following:

1. Orient yourself properly with the location of the DiskOnChip



socket. Try to locate the pin 1 location on your socket. Pin

numbers are usually printed on either the component side or the

solder side of your board.

2. Locate the Pin 1 location on your DiskOnChip



module. More

often than not, Pin 1 can be found on the lower right corner of

the chip. Please refer to the diagram for the exact location.

11

3. Once you have figured out where the pin 1 locations are on both

chip and socket, align the module’s pins on an upright angle

against the socket. Using both thumbs, gently press the module

into the socket until all the pins are secured to their

designations.

Pin 1

Location

D

i

s

k

O

n

C

h

i

p

4. The installation is now complete and your module is now ready

for use.

NOTE:

If you encounter difficulty installing your DiskOnChip



module,

please consult a qualified technician or engineer to perform the

installation.

3.7.1 Removing DiskOnChip



Modules

When removing a DiskOnChip



module from its socket, please take

note of the following:

1. Loosen the contact of the module from its socket using a

screwdriver.

2. Insert the screwdriver’s flat head into a gap on either end of the

socket. Do not insert the screwdriver head on either side where

the pins are located. Doing so might damage the pins in the

process.

3. Slowly lift the screwdriver handle upwards. This will disengage

the module from its socket.

NOTE:

If you encounter difficulty removing your DiskOnChip



module,

please consult a qualified technician or engineer to remove it for

you.

12

3.8 VGA Controller

The HS-2601A has an onboard jumper that selects the working voltage

of the flat panel connected to the system. Jumper JP2 offers two

voltage settings for the user.



JP2: Panel Voltage Select

Options Settings

5.0 V (default) Short 1-2

3.3 V Short 2-3

123

WARNING: Please contact the supplier of your panel and make sure of

the correct voltage it uses. Incorrect settings on JP8 may

cause internal damage to your panel.

The built-in C&T 69000 CRT/Panel display controller, onboard

HS-2601A, uses 2MB memory to support resolutions up to

1280x1024x256 colors.

The HS-2601A provides two connection methods of a VGA device.

CN20 offers a single standard CRT connector (DB15) while CN16 is

the 50-pin panel connector onboard reserved for flat panel installation.



CN6: 15-pin CRT Connector (DB15)

PIN Description PIN Description

1 Red 2 Green

3

Blue

4

N/C

5 GND 6 GND

7 GND 8 GND

9 N/C 10 GND

11 N/C 12 GND

13 HSYNC 14 VSYNC

15 GND

1

6

10

11

5

15

13



CN10: 50-pin Panel Connector

PIN. Description PIN Description

1 +12V 2 +12V

3 GND 4 GND

5 3.3V / 5V

Note

6 ENAVDD

7

ENAVEE

8

GND

9 P0 10 P1

11 P2 12 P3

13 P4 14 P5

15 P6 16 P7

17 P8 18 P9

19 P10 20 P11

21 P12 22 P13

23 P14 24 P15

25 P16 26 P17

27 P18 28 P19

29 P20 30 P21

31

P22

32

P23

33 P24 34 P25

35 SHFCLK 36 FLM

37 M 38 LP

39 GND 40 ENABKL

41 P26 42 P27

43 P28 44 P29

45 P30 46 P31

47 P32 48 P33

49 P34 50 P35

50

49

357911192123252729313335 131517373941434547

1

2

468101820222426283032 1214163436384042444648

NOTE:

Please set the proper voltage of your panel using JP8 before

proceeding on installing it.

14

3.9 IDE Drive Connector

CN12, a 44-pin connector, provides the PCI E-IDE drive provisions

onboard. A maximum of four IDE drives may be connected on them.

 CN12: Primary IDE Connector

CN15 Description CN15 Description

1

BRSTDRVJ

2

GND

3 DD7-1 4 DD8-1

5 DD6-1 6 DD9-1

7 DD5-1 8 DD10-1

9 DD4-1 10 DD11-1

11 DD3-1 12 DD12-1

13 DD2-1 14 DD13-1

15 DD1-1 16 DD14-1

17 DD0-1 18 DD15-1

19 GND 20 N/C

21 RPDDREQ- 22 GND

23 RPDIOW- 24 GND

25 RPDIOR- 26 GND

27

PIORDY

28

PRIPD1-

29 RPDACK- 30 GND

31 IRQ14 32 N/C

33 RPDA1- 34 N/C

35 RPDA0- 36 RPDA2-

37

RPCS1-

38

RPCS3-

39 HLED 40 GND

41 VCC 42 VCC

43 GND 44 VCC

1

2

40

39 3579171921232527293133 1113153537

46810

18

20

22

2426

28

30

3234

1214

1636

38

41

42

43

44

Page is loading ...

Intel HS-2601A User manual

Intel HS-2601A User manual

Related papers

Other documents