ProForm Treadmill PFTL14511.0 User manual

Category
Treadmills
Type
User manual

This manual is also suitable for

Serial Number
Decal
Model No. PFTL14511.0
Serial No.
Write the serial number in the space
above for reference.
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manual
for future reference.
QUESTIONS?
If you have questions, or if parts are
damaged or missing, DO NOT CON-
TACT THE STORE; please contact
Customer Care.
IMPORTANT: Please register this
product (see the limited warranty
on the back cover of this manual)
before contacting Customer Care.
CALL TOLL-FREE:
1-888-533-1333
Mon.–Fri. 6 a.m.–6 p.m. MT
Sat. 8 a.m.–4 p.m. MT
ON THE WEB:
www.proformservice.com
USERʼS MANUAL
www.proform.com
TABLE OF CONTENTS
WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
A
SSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
OPERATION AND ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
HOW TO FOLD AND MOVE THE TREADMILL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
EXERCISE GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
PART LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
EXPLODED DRAWING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
This drawing shows the locations of the
warning decals. If a decal is missing or il-
legible, call the telephone number on the
front cover of this manual and request a
free replacement decal. Apply the decal
in the location shown. Note: The decals
may not be shown at actual size.
WARNING DECAL PLACEMENT
2
PROFORM is a registered trademark of ICON IP, Inc.
3
1. Before beginning any exercise program, con-
sult your physician. This is especially impor-
tant for persons over age 35 or persons with
pre-existing health problems.
2. It is the responsibility of the owner to ensure
that all users of this treadmill are adequately
informed of all warnings and precautions.
3. Use the treadmill only as described.
4. Keep the treadmill indoors, away from mois-
ture and dust. Do not put the treadmill in a
garage or covered patio, or near water.
5. Place the treadmill on a level surface, with at
least 8 ft. (2.4 m) of clearance behind it and 2
ft. (0.6 m) on each side. Do not place the
treadmill on any surface that blocks air open-
ings. To protect the floor or carpet from dam-
age, place a mat under the treadmill.
6. Do not operate the treadmill where aerosol
products are used or where oxygen is being
administered.
7. Keep children under age 12 and pets away
from the treadmill at all times.
8. The treadmill should be used only by persons
weighing 350 lbs. (159 kg) or less.
9. Never allow more than one person on the
treadmill at a time.
10. Wear appropriate exercise clothes when
using the treadmill. Do not wear loose clothes
that could become caught in the treadmill.
Athletic support clothes are recommended
for both men and women. Always wear ath-
letic shoes. Never use the treadmill with bare
feet, wearing only stockings, or in sandals.
11. When connecting the power cord (see page
15), plug the power cord into a surge sup-
pressor (not included) and plug the surge
suppressor into a grounded circuit capable of
carrying 15 or more amps. No other appliance
should be on the same circuit. Do not use an
extension cord.
12. Use only a single-outlet surge suppressor that
meets all of the specifications described on
page 15. To purchase a surge suppressor, see
your local PROFORM dealer or call the tele-
phone number on the front cover of this man-
ual and order part number 146148, or see your
local electronics store.
13. Failure to use a properly functioning surge
suppressor could result in damage to the con-
trol system of the treadmill. If the control sys-
tem is damaged, the walking belt may slow,
accelerate, or stop unexpectedly, which may
result in a fall and serious injury.
14. Keep the power cord and the surge suppres-
sor away from heated surfaces.
15. Never move the walking belt while the power
is turned off. Do not operate the treadmill if
the power cord or plug is damaged, or if the
treadmill is not working properly. (See TROU-
BLESHOOTING on page 30 if the treadmill is
not working properly.)
16. Read, understand, and test the emergency
stop procedure before using the treadmill (see
HOW TO TURN ON THE POWER on page 17).
17. Never start the treadmill while you are stand-
ing on the walking belt. Always hold the
handrails while using the treadmill.
18. The treadmill is capable of high speeds.
Adjust the speed in small increments to avoid
sudden jumps in speed.
19. The pulse sensor is not a medical device.
Various factors, including the user's move-
ment, may affect the accuracy of heart rate
readings. The pulse sensor is intended only
as an exercise aid in determining heart rate
trends in general.
WARNING: To reduce the risk of serious injury, read all important precautions and in-
s
tructions in this manual and all warnings on your treadmill before using your treadmill. ICON as-
sumes no responsibility for personal injury or property damage sustained by or through the use of
this product.
IMPORTANT PRECAUTIONS
4
2
0. Never leave the treadmill unattended while it
is running. Always remove the key, unplug
the power cord, and press the power switch
into the off position when the treadmill is not
in use. (See the drawing on page 5 for the lo-
cation of the power switch.)
21. Do not attempt to raise, lower, or move the
treadmill until it is properly assembled. (See
ASSEMBLY on page 6, and HOW TO FOLD
AND MOVE THE TREADMILL on page 29.)
You must be able to safely lift 45 lbs. (20 kg)
to raise, lower, or move the treadmill.
22. When folding or moving the treadmill, make
sure that the storage latch is holding the
frame securely in the storage position.
23. Never insert any object into any opening on
the treadmill.
2
4. Inspect and properly tighten all parts of the
treadmill regularly.
25.
DANGER: Always unplug the power
cord immediately after use, before cleaning the
treadmill, and before performing the mainte-
n
ance and adjustment procedures described in
this manual. Never remove the motor hood un-
less instructed to do so by an authorized ser-
vice representative. Servicing other than the
procedures in this manual should be performed
by an authorized service representative only.
26. This treadmill is intended for in-home use
only. Do not use this treadmill in a commer-
cial, rental, or institutional setting.
27. Over exercising may result in serious injury
or death. If you feel faint or if you experience
pain while exercising, stop immediately and
cool down.
SAVE THESE INSTRUCTIONS
5
Thank you for selecting the revolutionary PROFORM
®
P
ERFORMANCE 1450 treadmill. The
PERFORMANCE 1450 treadmill offers an impressive
selection of features designed to make your workouts
at home more enjoyable and effective. And when
y
ouʼre not exercising, the unique treadmill can be
folded up, requiring less than half the floor space of
other treadmills.
For your benefit, read this manual carefully before
using the treadmill. If you have questions after read-
ing this manual, please see the front cover of this man-
u
al. To help us assist you, please note the product
model number and serial number before contacting us.
The model number and the location of the serial num-
ber decal are shown on the front cover of this manual.
Before reading further, please review the drawing
below and familiarize yourself with the labeled parts.
BEFORE YOU BEGIN
Handrail
Upright
Tray
Key/Clip
Power Switch
Walking Belt
Platform Cushion
Foot Rail
Power Cord
Idler Roller
Adjustment Bolts
Console
Pulse Sensor
6
ASSEMBLY
T
o hire an authorized service technician to assemble the treadmill, call 1-800-445-2480.
Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials. Do not
dispose of the packing materials until assembly is completed. Note: The underside of the treadmill walking
b
elt is coated with high-performance lubricant. During shipping, some lubricant may be transferred to the top of
the walking belt or the shipping carton. This is normal and does not affect treadmill performance. If there is lubri-
cant on top of the walking belt, simply wipe off the lubricant with a soft cloth and a mild, non-abrasive cleaner.
Assembly requires the included hex keys and your own Phillips screwdriver , adjustable
wrench , and scissors .
Use the drawings below to identify the assembly hardware. The number in parentheses below each drawing is
the key number of the part, from the PART LIST near the end of this manual. The number after the parentheses
is the quantity needed for assembly. Note: Some small parts may have been preassembled. To avoid dam-
aging parts, do not use power tools for assembly. Extra hardware may be included.
#8 x 3/4" Screw
(2)–8
3/8" Star
Washer (13)–4
3/8" Nut (12)–2
5/16" Star
Washer (11)–4
#10 x 3/4" Screw
(9)–2
3/8" x 2 3/4" Bolt (7)–4
3/8" x 1 3/4" Bolt (6)–1
3/8" x 2" Bolt (3)–1
5/16" x 1"
Bolt (5)–4
#8 x 1/2" Ground
Screw (10)–1
#8 x 1/2" Screw
(1)–18
5/16" x 1 1/4"
Bolt (4)–2
3/8" x 1 1/4" Bolt (8)–4
1/4" Star
Washer (35)–6
1/4" x 1/2"
Bolt (36)–4
5/16" Flat
Washer (113)–4
#10 x 3/4" Flat
Head Screw (112)–2
7
3. Identify the Left Upright (89), which is marked
with a “Left” sticker or an “L” sticker. Have a sec-
ond person hold the Left Upright near the Base
(94).
See the inset drawing. Tie the wire tie in the
Left Upright (89) securely around the end of the
Upright Wire (81). Then, pull the other end of the
wire tie until the Upright Wire is routed com-
pletely through the Left Upright.
81
3
1
. Make sure that the power cord is unplugged.
Place a piece of cardboard below the rear of the
F
rame (56) to protect the floor or carpet.
Attach the Left Wheel Cap (96) to the Base (94)
with two #8 x 3/4" Screws (2).
Attach the Right Wheel Cap (not shown) to
the right side of the Base (94) in the same
way.
1
96
94
2
81
89
Wire
Tie
Wire
Tie
89
94
56
Cardboard
81
2. Pull the Upright Wire (81) and the Base Ground
Wire (110) through the indicated hole in the
Base (94).
Attach the Base Ground Wire (110) to the Base
(94) with a #8 x 1/2" Ground Screw (10).
81
2
Hole
10
110
94
8
5. Identify the Left Base Cover (82) and the Right
Base Cover (83). Slide the Left Base Cover onto
the Left Upright (89). Slide the Right Base Cover
onto the Right Upright (90). Do not press the
Base Covers into place yet.
Identify the Left Upright Cover (79) and the
Right Upright Cover (80). Slide the Left Upright
Cover onto the Left Upright (89). Slide the Right
Upright Cover onto the Right Upright (90).
89
82
80
90
79
83
5
4. Hold the Left Upright (89) against the Base
(94). Be careful not to pinch the Upright
Wire (81). Insert two 3/8" x 1 1/4" Bolts (8) with
t
wo 3/8" Star Washers (13) and two 3/8" x
2 3/4" Bolts (7) into the Left Upright.
Partially tighten the 3/8" x 2 3/4" Bolts (7) and
the 3/8" x 1 1/4" Bolts (8) until the heads of the
Bolts touch the Left Upright (89); do not fully
tighten the Bolts yet. Note: It may be helpful
to use the Short Hex Key (64) on the Bolt
shown.
Attach the Right Upright (not shown) in the
same way. Note: There are no wires on the
right side.
89
94
64
4
81
8
7
13
13
9
7. Attach the Left Handrail (88) to the Left Upright
(89) with two 5/16" x 1" Bolts (5), two 5/16" Star
Washers (11), and a 5/16" x 1 1/4" Bolt (4). Do
not tighten the Bolts yet.
Attach the Right Handrail (87) in the same
way.
7
89
88
87
4
4
5
5
11
11
6. Cut the plastic tie in the Left Handrail (88) and
the Right Handrail (not shown). If necessary,
press the 5/16" Cage Nuts (31) back into place.
I
dentify the Left Handrail (88) and hold it near
the Left Upright (89). Insert the Upright Wire
(81) through the bracket on the bottom of the
Left Handrail. Pull the Upright Wire out of the
e
nd of the Left Handrail.
88
6
89
31
81
Tie
10
10. With the help of a second person, hold the con-
sole assembly near the Left Handrail (88).
Connect the Upright Wire (81) to the console
wire. See the inset drawing. The connectors
should slide together easily and snap into
place. If they do not, turn one connector and try
again. IF YOU DO NOT CONNECT THE CON-
NECTORS PROPERLY, THE CONSOLE MAY
BECOME DAMAGED WHEN YOU TURN ON
THE POWER. Remove the wire tie from the
Upright Wire.
Console
Assembly
Console
Wire
Wire
Tie
88
81
81
Console
Wire
8. Set the console assembly face down on a soft
surface to avoid scratching the console
assembly.
Remove all the Screws (A) attaching the
C
rossbar (93). Next, lift off the Crossbar.
Discard the Screws.
93
Console
A
ssembly
A
8
10
9. IMPORTANT: To avoid damaging the
Crossbar (93), do not use power tools and
do not overtighten the #10 x 3/4" Screws (9)
or the #10 x 3/4" Flat Head Screws (112).
Orient the Crossbar (93) as shown. Attach the
Crossbar to the Handrails (87, 88) with two #10
x 3/4" Flat Head Screws (112), two #10 x 3/4"
Screws (9), and two 1/4" Star Washers (35) as
shown. Start all four Screws, and then tighten
each of them.
93
88
9
9
9
87
35
112
112
35
11
12. Tighten the four 3/8" x 2 3/4" Bolts (7) first and
then the four 3/8" x 1 1/4" Bolts (8) (only one
side is shown).
Press the Left Base Cover (82) and the Right
Base Cover (83) onto the Base (94) until they
snap into place.
12
83
8
82
94
11. Set the console assembly on the Right Handrail
(87) and the Left Handrail (88). Be careful not
to pinch any wires. Insert the excess Upright
W
ire (not shown) into the Left Handrail.
A
ttach the console assembly with six #8 x 1/2"
Screws (1) and four 1/4" x 1/2" Bolts (36) with
four 5/16" Flat Washers (113) and four 1/4" Star
Washers (35) as shown. Start all six Screws
and all four Bolts, and then tighten each of
them.
See step 7. Tighten the four 5/16" x 1" Bolts (5)
and the two 5/16" x 1 1/4" Bolts (4).
3
5
88
1
11
Console
Assembly
1
7
87
36
1
1
36
13. Slide the Left Handrail Cover (85) onto the Left
Handrail (88). Slide the Right Handrail Cover
(86) onto the Right Handrail (87). Attach each
Handrail Cover with a #8 x 1/2" Screw (1).
13
85
86
1
1
87
88
35
113
113
14. Hold the Left Upright Cover (79) against the
console assembly. Align the holes in the Left
Upright Cover with the holes in the Left Upright
(89). Attach the Left Upright Cover with three #8
x
1/2" Screws (1).
Attach the Right Upright Cover (80) to the
Right Upright (90) in the same way.
1
4
89
1
Console
Assembly
79
1
90
80
1
15. Attach the Left Tray (107) and the Right Tray
(108) to the console assembly with four #8 x 1/2"
Screws (1).
107
108
15
Console
Assembly
1
1
1
16. Make sure that there is a piece of cardboard
below the rear of the Frame (56).
56
16
Cardboard
12
13
18. IMPORTANT: Before you begin this step,
make sure that you have read and followed
all of the instructions in step 17.
Raise the Frame (56) to the position shown.
Have a second person hold the Frame until
this step is completed.
Orient the Storage Latch (53) so that the large
barrel and the latch knob are oriented as shown;
make sure the caps remain in the ends of the
Storage Latch.
Attach the lower end of the Storage Latch (53) to
the Base (94) with a 3/8" x 2" Bolt (3) and a 3/8"
Nut (12).
Attach the upper end of the Storage Latch (53)
to the bracket on the Frame (56) with a 3/8" x
1 3/4" Bolt (6) and a 3/8" Nut (12). Note: It may
be necessary to move the Frame (56) back and
forth to align the Storage Latch with the Base.
18
53
Large
Barrel
56
Latch
Knob
12
12
6
3
94
17. IMPORTANT: See page 15 and plug in the
power cord. Next, see page 17 and turn on
the power.
S
ee page 27; follow steps 1 through 3.
When the frame stops moving, remove the
key from the console and unplug the power
c
ord.
17
IMPORTANT:
Make sure to follow all
instructions in this step.
14
21. Make sure that all parts are properly tightened before you use the treadmill. If there are sheets of plastic
on the treadmill decals, remove the plastic. To protect the floor or carpet, place a mat under the treadmill.
Note: Extra hardware may be included. Keep the included hex keys in a secure place; one of the hex keys is
used to adjust the walking belt (see pages 31 and 32).
20. Press the Grommet (77) into the square hole in
the Base (94).
94
77
20
19. Attach the Rear Feet (57) to the Frame (56) as
shown with four #8 x 3/4" Screws (2).
See step 16. Discard the piece of cardboard.
Lower the Frame (56) (see HOW TO LOWER
THE TREADMILL FOR USE on page 29).
19
5
7
2
2
57
56
15
OPERATION AND ADJUSTMENT
T
HE PRE-LUBRICATED WALKING BELT
Your treadmill features a walking belt coated with high-
performance lubricant. IMPORTANT: Never apply sil-
i
cone spray or other substances to the walking
belt or the walking platform. Such substances will
cause excessive wear.
HOW TO PLUG IN THE POWER CORD
Your treadmill, like other electronic equipment, can be
damaged by sudden voltage changes in your homeʼs
power. To decrease the risk of damaging your
treadmill, always use a surge suppressor with your
treadmill (see drawing 1 at the right). To purchase
a surge suppressor, see precaution 12 on page 3.
Use only a single-outlet surge suppressor that is
UL 1449 listed as a transient voltage surge sup-
pressor (TVSS). The surge suppressor must have a
UL suppressed voltage rating of 400 volts or less
and a minimum surge dissipation of 450 joules.
The surge suppressor must be electrically rated for
120 volts AC and 15 amps. There must be a moni-
toring light on the surge suppressor to indicate
whether it is functioning properly. Failure to use a
properly functioning surge suppressor could dam-
age the control system of the treadmill (see precau-
tion 13 on page 3).
This product must be grounded. If it should malfunc-
tion or break down, grounding provides a path of least
resistance for electric current to reduce the risk of elec-
tric shock. This productʼs power cord has an equip-
ment-grounding conductor and a grounding plug. Plug
the power cord into a surge suppressor, and plug
the surge suppressor into an appropriate outlet
that is properly installed and grounded in accor-
d
ance with all local codes and ordinances.
IMPORTANT: The treadmill is not compatible with
GFCI-equipped outlets and may not be compatible
with AFCI-equipped outlets.
This product is for use on a nominal 120-volt circuit
(see drawing 1). A temporary adapter may be used to
connect the surge suppressor to a 2-pole receptacle if
a properly grounded outlet is not available (see draw-
ing 2).
The temporary adapter should be used only until a
properly grounded outlet (see drawing 1) can be in-
stalled by a qualified electrician.
The green-colored rigid ear, lug, or the like extending
from the adapter must be connected to a permanent
ground such as a properly grounded outlet box cover.
The adapter must be held in place by a metal screw.
Some 2-pole receptacle outlet box covers are not
grounded. Contact a qualified electrician to deter-
mine if the outlet box cover is grounded before
using an adapter.
DANGER: Improper connection
of the equipment-grounding conductor in-
creases the risk of electric shock. Check with
a qualified electrician or serviceman if you
are unsure whether the product is properly
grounded. Do not modify the plug—if it will
not fit the outlet, have a proper outlet in-
stalled by a qualified electrician.
1
2
Grounded Outlet Box
Grounded Outlet Box
Grounding Plug
Surge Suppressor
Surge Suppressor
Grounding Pin
Adapter
Lug
Metal Screw
Grounded Outlet
Grounding Pin
Grounding Plug
16
FEATURES OF THE CONSOLE
The treadmill console offers an impressive array of
features designed to make your workouts more effec-
tive and enjoyable. The console features iFit Live tech-
nology that enables the treadmill to communicate with
your wireless network. With iFit Live, you can down-
load personalized workouts, create your own workouts,
track your workout results, and access many other fea-
tures. See www.iFit.com for complete information.
In addition, the console features twenty-six onboard
workouts—six calorie workouts, seven intensity work-
outs, six speed workouts, and seven incline workouts.
Each workout automatically controls the speed and in-
cline of the treadmill as it guides you through an effec-
tive exercise session.
When you use the manual mode, you can change the
speed and incline of the treadmill with the touch of a
button. As you exercise, the console will display instant
exercise feedback. You can also measure your heart
rate using the handgrip pulse sensor.
You can even browse the Internet or listen to your fa-
vorite workout music or audio books with the consoleʼs
stereo sound system while you exercise.
To turn on the power, see page 17. To set up the
console, see page 17. To use the manual mode, see
page 18. To use an onboard workout, see page 21.
To use an iFit Live workout, see page 22. To use
the Internet browser, see page 24. To use the set-
tings mode, see page 25. To use the maintenance
mode, see page 27. To use the stereo sound sys-
tem, see page 28.
Note: The console can display speed and distance in
either miles or kilometers. To find which unit of mea-
surement is selected, see step 5 on page 26. For sim-
plicity, all instructions in this manual refer to miles.
IMPORTANT: If there are sheets of plastic on the
console, remove the plastic. To prevent damage to
the walking platform, wear clean athletic shoes
while using the treadmill. The first time you use the
treadmill, observe the alignment of the walking
belt, and center the walking belt if necessary (see
page 31).
CONSOLE
DIAGRAM
17
HOW TO TURN ON THE POWER
IMPORTANT: If the treadmill has been exposed to
c
old temperatures, allow it to warm to room tem-
perature before you turn on the power. If you do
n
ot do this, you may damage the console display
or other electrical components.
Plug in the power cord (see
page 15). Next, locate the
power switch on the treadmill
frame near the power cord.
Make sure that the switch is
in the reset position.
IMPORTANT: The console features a display demo
mode, designed to be used if the treadmill is dis-
played in a store. If the demo mode is turned on,
the display will show a demo presentation after
you plug in the power cord and press the power
switch into the reset position, before you insert the
key. To turn off the demo mode, see step 6 on
page 26.
Next, stand on the foot
rails of the treadmill.
Locate the clip at-
tached to the key, and
slide the clip securely
onto the waistband of
your clothes. Then, in-
sert the key into the
console. IMPORTANT:
In an emergency, the key can be pulled from the
console, causing the walking belt to slow to a stop.
Test the clip by carefully taking a few steps back-
ward; if the key is not pulled from the console, ad-
just the position of the clip.
Note: It may take a minute for the console to be
ready for use.
HOW TO SET UP THE CONSOLE
Before using the treadmill for the first time, set up your
c
onsole.
1
. Connect to a wireless network.
See steps 1 and 2 on
page 25 to connect to a
wireless network. Then,
touch the home button
on the console to return
to the settings mode.
An information box may appear to explain how to
return to the settings mode. To hide this message
in the future, touch the Donʼt Show Again check-
box. Then, touch the Continue button.
2. Calibrate the screen.
First, select the maintenance mode (see steps 1
and 2 on page 27). Then, see step 6 on page 28
and calibrate the screen.
3. Calibrate the incline system.
First, select the maintenance mode (see steps 1
and 2 on page 27). Then, see step 3 on page 27
and calibrate the incline system of the treadmill.
4. Check for firmware updates.
See step 5 on page 27 and check for firmware up-
dates.
5. Create an iFit Live account.
See step 1 on page 25 to select the settings mode.
Note: If you have already created an iFit Live ac-
count, go to to step 6.
Touch the globe button near the lower-left corner
of the screen and then touch the iFit Live button.
A box may appear with directions for navigating in
the Internet browser. To hide this message in the
future, touch the Donʼt Show Again checkbox.
Then, touch the Continue button. Note: For infor-
mation about navigating in the browser, see page
24.
Reset
Key
Clip
18
The browser will open to the iFit.com home page.
Touch the Register Now button in the upper-right
corner of the screen.
The browser will open to the iFit.com registration
p
age. Touch an entry box to view the keyboard.
Slide your finger up or down the screen to scroll up
or down the page.
Enter a username and password and your e-mail
address. Next, enter the activation code from the
iFit Live flier that came with the treadmill. Touch
the Place of Purchase drop-down menu for a list of
options; then, touch the location where you pur-
chased your product. Touch the words MEDICAL
DISCLAIMER, read the medical disclaimer, touch
the I Accept button, and check the medical dis-
claimer checkbox. Then, touch the Confirm
Activation Code button.
Enter the requested personal information. When
you have entered all of the information, touch the
Finish button. When the registration process is
complete, press the home button on the console to
exit the browser.
6. Begin working out.
Touch the iFit Live Login button. The screen will
ask for your iFit.com user name and password.
Enter them and touch the Submit button. Touch the
Cancel button to exit the login screen.
The console will display the iFit Live welcome
screen. Before some workouts will download, you
must add the workouts to your schedule on
iFit.com. For more information about iFit Live work-
outs, see pages 22 and 23 or go to www.iFit.com.
HOW TO USE THE MANUAL MODE
1. Insert the key into the
c
onsole.
S
ee HOW TO TURN
ON THE POWER on
page 17. Note: It may
take a minute for the
console to be ready for use.
2. Select the start-up menu.
Each time the key is inserted, the start-up menu
will appear. If you have selected a workout or the
iFit Live mode, touch the home button in the lower
left corner of the screen. Next, touch the End
Workout button and then touch the Done button to
return to the start-up menu.
3. Start the walking belt and adjust the speed.
To start the walking belt, touch the Start button on
the screen or the Start button on the console. The
walking belt will begin to move at 1 mph. As you
exercise, change the speed of the walking belt as
desired by pressing the Speed increase and de-
crease buttons. Each time you press one of the
buttons, the speed setting will change by 0.1 mph;
if you hold down the button, the speed setting will
change in increments of 0.5 mph.
If you press one of the numbered 1 Step Speed
buttons, the walking belt will gradually change
speed until it reaches the selected speed setting.
To select a speed setting that includes a decimal—
such as 3.5 mph—press two numbered buttons in
succession. For example, to select a speed setting
of 3.5 mph, press the 3 button and then immedi-
ately press the 5 button.
To stop the walking belt, press the Stop button. To
restart the walking belt, press the Start button.
You can also press the Manual button on the con-
sole. To start the walking belt after you press the
Manual button, press the Speed increase button.
19
4. Change the incline of the treadmill as desired.
To change the incline of the treadmill, press the
I
ncline increase and decrease buttons or one of the
numbered 1 Step Incline buttons. Each time you
p
ress one of the buttons, the incline will gradually
change until it reaches the selected incline setting.
Note: The first time you adjust the incline, you must
first calibrate the incline system (see step 3 on
page 27).
5. Monitor your progress.
The console offers several display modes. The dis-
play mode that you select will determine which
workout information is shown. To select the de-
sired display mode, repeatedly touch the Display
increase or decrease button on the screen.
As you walk or run on the treadmill, the screen can
show the following workout information:
The incline level of the treadmill
The elapsed time
The approximate number of calories you have
burned
The distance that you have walked or run
The speed of the walking belt
A track representing 1/4 mile (400 meters)
Your pace in minutes per mile
Your current lap number
The time remaining
The approximate number of calories burned per
hour
The number of vertical feet you have climbed
Your heart rate (see step 6 on page 20).
The displays at the top of the screen can show two
t
ypes of information. Touch each display until the
display shows the desired information. Note: The
manual mode does not have a time remaining
countdown.
If desired, adjust the vol-
ume level by pressing
the volume increase and
decrease buttons on the
console.
To reset the console, touch the home button in the
lower left corner of the screen. To pause the work-
out, touch the Pause button. To continue the work-
out, touch the Resume button or the Start button.
To end the workout and select a new workout,
touch the New Workout button. To end the workout
session, touch the End Workout button.
Note: The small wireless
symbol in the lower right
corner of the screen will
show your wireless con-
nection status. If the
symbol is green, the
treadmill is connected to
your wireless network and you have logged in to
iFit.com. If the symbol is orange, the treadmill is
connected to your wireless network. If the symbol
is black, the treadmill is not connected to your wire-
less network.
Volume Decrease
Volume Increase
20
6. Measure your heart rate if desired.
Before using the
h
andgrip pulse
sensor, remove
t
he sheets of
plastic from the
metal contacts
on the pulse bar.
In addition, make
sure that your
hands are clean.
To measure your heart rate, stand on the foot
rails and hold the pulse bar with your palms on the
metal contacts for approximately ten seconds;
avoid moving your hands. When your pulse is
detected, your heart rate will be shown. For the
most accurate heart rate reading, continue to
hold the contacts for about 15 seconds.
7. Turn on the fan if desired.
The fan features several speed settings and an
auto mode. When the auto mode is selected, the
speed of the fan will automatically increase and de-
crease as the speed of the walking belt increases
and decreases.
Press the Manual fan button repeatedly to select a
f
an speed or to turn off the fan. Press the Auto fan
button to select the auto mode or to turn off the
fan.
8. When you are finished exercising, remove the
key from the console.
Step onto the foot rails, press the Stop button, and
adjust the incline of the treadmill to the lowest
incline setting. The incline must be at the low-
est incline setting or you may damage the
treadmill when you fold it to the storage posi-
tion. Next, remove the key from the console and
put it in a secure place.
When you are finished using the treadmill, press
the power switch into the off position and unplug
the power cord. IMPORTANT: If you do not do
this, the treadmillʼs electrical components may
wear prematurely.
Contacts
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40

ProForm Treadmill PFTL14511.0 User manual

Category
Treadmills
Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI