Sanyo 42SRE1 User manual

CE

42SRE1

LCD Monitor

Moniteur d'affichage à cristaux liquides

LCD-Monitor

LCD-Display

Monitor LCD

Monitor de LCD

Instruction Manual

Manuel d'utilisation

Bedienungsanleitung

Gebruiksaanwijzing

Manuale d'Istruzioni

Manual de instrucciones

English Page 2~11

Deutsch Seite 22~31

Français Page 12~21

Nederlands Bladzijde 32~41

GB

D

F

NL

Italiano Pagine 42~51

I

Please read this Instruction book before using your LCD monitor. We wish you many hours of pleasure from your new LCD monitor

Veuillez lire attentivement ce mode d’emploi avant d’utiliser votre moniteur d’affichage à cristaux liquides. Nous espérons que votre

nouveau dispositif d'affichage vous procurera de nombreux instants de bonheur.

Lesen Sie diese Anleitung bitte aufmerksam durch, bevor Sie Ihren LCD- Monitor in Betrieb nehmen. Wir wünschen Ihnen viel Freude

mit Ihrem neuen Gerät.

Lees deze handleiding voordat u uw LCD- monitor gaat gebruiken. We wensen u vele uren van plezier met uw nieuwe beeldscherm.

Leggere attentamente questo manuale d’istruzioni prima di utilizzare il monitorLCD. Vi ringraziamo per aver scelto un monitor LCD

Sanyo che vi consentirà di trascorrere momenti piacevoli e divertenti.

Lea este manual de instrucciones antes de usar su nuevo monitor. Deseamos que disfrute de él muchas horas.

Español Página

52

~

64

E

2

GB

Do not allow anything to rest on the power

cord. Do not locate this LCD monitor where

the cord will be damaged by people walking

on it.

Do not overload wall outlets and extension

cords as this can result in fire or electric

shock.

A suitable socket outlet must be provided

near to the monitor and shall be easily accessible

Do not place this LCD monitor near any heat sources such as

radiators, heaters, stoves and other heat-generating products

(including amplifiers).

Do not place your LCD monitor on an unstable stand, shelf or

table. Serious injury to an individual, and damage to the LCD

monitor may result if it should fall. Your sales person can

recommend approved wall mounting kit. A special wall mounting

kit is available for this model.

This LCD monitor should be operated only from the type of power

source indicated on the monitor or as indicated in the Operating

Instructions. If you are not sure of the type of power supply, con-

sult your sales person or your local power company.

For added protection it is strongly recommended that this LCD

monitor is supplied via an approved earth fault protection device.

WARNING:

To prevent injury the LCD monitor must be securely

attached to the wall in accordance with the manufacturers installa-

tion instructions.

IMPORTANT:

This product must be earthed

This unit is not disconnected from the mains unless the mains lead is

unplugged The installer must make sure that the mains plug is easily

accessible.

Do not use immediately after moving the LCD monitor from a low

temperature to a high temperature environment, as this causes

condensation, which may result in fire, electric shock, or other

hazards. Before cleaning, unplug the monitor from the wall

socket.

Do not mount near an open flame source. Open flames must

never be used near this LCD monitor.

This LCD monitor should not be built in or enclosed in any way,

heat build up will reduce the life of the monitor.

This LCD monitor should have a minimum distance of 5cm away

from the wall and the monitor should have 10cm distance around

the top and sides.

Always mount using recommended and substantial fixtures and

fittings.

Do not apply liquid cleaners or aerosol cleaners directly onto the

LCD monitor. Use a damp cloth for cleaning.

Installation and Use

CAUTION: Please read and retain for your safety. This unit has been engineered and manufactured to assure your personal safety, but

improper use can result in potential electric shock or fire hazards. In order not to defeat the safeguards incorporated in this monitor observe the

following basic rules for its installation, use and servicing.

Important recycling information.

Your SANYO product is designed and

manufactured with high quality materials and

components which can be recycled and reused.

This symbol means that electrical and electronic

equipment, at their end-of-life, should be

disposed of separately.

In the European Union there are separate col-

lection systems for used electrical and electronic

products.

Please help us to conserve the environment we

live in!

Note: This symbol mark and recycle system are applied only to EU

countries are not applied to other countries of the world.

Important:

THIS PRODUCT MUST BE EARTHED

This equipment is fitted with an approved mains lead and an

approved non rewireable UK mains plug. To change a fuse in this

type of plug proceed as follows:

1. Remove the fuse cover and fuse.

2. Fit a new fuse which should be a BS1362 13 Amp A.S.T.A. or

BSI approved type.

3. Ensure that the fuse cover is correctly refitted.

If the fuse cover is lost or damaged the plug must NOT be used

but replaced with a serviceable plug.

If the fitted plug is not suitable for your socket outlets, it should be

cut off and an appropriate plug fitted in its place. If the mains plug

contains a fuse, this should have a rating of 13 Amp, ensure the

fuse cover is correctly fitted. If a plug without a fuse is used, the

fuse at the distribution board should not be greater than 13 Amp.

Note:

The severed plug must be destroyed to avoid a possible

shock hazard should it be inserted into a 13 Amp socket elsewhere.

The wires in this mains lead are coloured in accordance with the

following code:

Blue -------> Neutral

Brown ----> Live

Green and Yellow ----> Earth

1. The Blue wire must be connected to the terminal which is

marked with the letter “N” or coloured BLACK.

2. The Brown wire must be connected to the terminal with the

letter “L” or coloured RED.

3. The Green and Yellow wire must be connected to the terminal

which is marked with the letter “E” or coloured GREEN or

GREEN and YELLOW.

Before replacing the plug cover, make certain that the cord grip is

clamped over the sheath of the lead - not simply over the wires.

Do not attempt to bypass the safety purpose of the grounding

type plug.

THIS UNIT IS NOT DISCONNECTED FROM THE MAINS UNLESS

THE MAINS LEAD IS UNPLUGGED.

THE INSTALLER MUST MAKE SURE THE MAINS LEAD IS

EASILY ACCESSIBLE.

GB

3

GB

Your monitor is fully transistorised and does not contain any user serviceable components.

You must not remove the rear cover of the monitor by yourself. The apparatus is working with high voltages and could damage

objects or even endanger people. Leave all required repair and service jobs to an authorised service technician. He will exclusively

use such spare parts that are complying with the same safety standards as applicable to the original parts. The use of original spare

parts can prevent fire, shock and other hazards.

Unplug the LCD monitor from the wall outlet and refer servicing to qualified service personnel under the following conditions:

■

If the power cord or plug is damaged.

■

If liquid has been spilt in to the LCD monitor.

■

If the LCD monitor has been exposed to rain or water.

■

If the LCD monitor has been dropped or the cabinet has been damaged.

■

If the LCD monitor exhibits a distinct change in performance.

■

If the LCD monitor does not operate normally by following the operating instructions.

Adjust only those controls that are covered in the operating instructions as improper adjustment of other controls may result in damage. This will

often require extensive work by a qualified technician to restore the monitor to normal operation.

Servicing

The product (meaning the equipment or appliance to which this

documentation relates) incorporates Software (the software applica-

tions, utilities and modules embedded within the Product) which is

owned by Sanyo or its licensors. Before using the product, please

read the End-User License Conditions detailed below. If you do not

agree to the terms and conditions of the End-User License, Please

do not proceed to use the Product- repack the Product unused and

return it to your supplier together with proof of purchase for a full

refund. By using the product, you agree to be bound by the terms

and conditions of the End-User License.

License Grant, Conditions and restrictions

1.

Sanyo grants you a non-exclusive, world-wide (subject to export

controls), non-transferable (except as permitted by 2 below),

royalty-free license to use the Software upon and with the Product.

2.

You may not transfer any of your license rights in the Software

without the prior written consent of SANYO and if consent is

provided then the Software shall only be transferred in conjunction

with the transfer of the Product AND provided that the transferee

has read and agreed to accept the terms and conditions of this

license.

3.

You must ensure that the copyright, trademark and other protective

notices contained in the Software are maintained and not altered

or removed.

4.

The Software provided hereunder is copyrighted and licensed (not

sold). SANYO especially does not transfer title or and ownership

rights in the Software to you. The Software provided hereunder

may contain or be derived from portions of materials provided to

SANYO under license by a third party supplier.

5.

Except as expressly permitted by statute

you may not;

●

use the Software in conjunction with any other computer

hardware other than the product;

●

copy all or part of the Software;

●

incorporate all (or any of) the Software into other programs

developed by (or on behalf of) you and/or used by you;

●

reverse-engineer, decompile or disassemble the Software;

●

make the Software (or any part of it) available, or permit its

redistribution, for use with any computer hardware other than the

Product; or rent, lease, gift, loan, sell, distribute or transfer pos-

session of the whole or any part of the Software.

Termination

This license is effective until terminated. This license will terminate

automatically without notice if you fail to comply with any of its

p r o v i s i o n s .

Disclaimer

1.

The Software is(to the extent permitted by law) supplied ‘as is’ and

SANYO and its suppliers expressly exclude all warranties, express

or implied, including (but not limited to) warranties of satisfactory

quality, fitness for purpose and non-infringement (save to the

extent that the same are not capable of exclusion at law).

2.

In no circumstances will SANYO be liable for any direct, indirect,

consequential, or incidental damage (including loss of profits,

business interruption, loss of data or the cost of procurement of

substitute goods, technology or services) arising out of the use or

the inability to use the Software (save to the extent that such

liability is not capable of exclusion at law).

General

1.

This End-User License will be governed by laws of England and

the User may only bring claims in the English Courts and SANYO

shall be entitled to bring a claim in the courts of any jurisdiction.

2.

The above terms and conditions supersede any prior agreement,

oral or written, between you and SANYO relating to the Software.

End-User License

4

■

Connect the display unit to VGA, BNC and Scart

connector as required.

1. Connect the IEC power connector to the mains inlet at the rear of

the LCD monitor as shown above.

2. Connect the power cord of the LCD monitor to a wall outlet.

✐

As this product does not have a mains On/Off switch, please

ensure your mains plug is easily accessible.

✐

The LCD monitor is prepared for a mains voltage AC220~240V,

50Hz. To completely switch off the mains, or when the display unit

is not to be used for an extended period of time, it is advisable to

disconnect the power cord from the power outlet.

✐

Please use the correct mains lead supplied with the set for your

area

3

.

Warning: To prevent injury, the unit must be securely attached to

the wall in accordance with the installation instructions.

■

INPUT selection

To switch between AV1, RGB, AV2 (RGB H/V or Y, Pb, Pr) AV3, DVI

or PC mode press the TV/ AV button on your remote control

repeatedly or press and hold the TV/AV button for a few seconds and

a selection menu will appear on screen.Use the e or d buttons to

select the correct input.

1.

AV1

SCART connection

2.

RGB

TTL input (5V RGB signals) into SCART terminal

3.

Y,Pb,Pr/ RGBHV connection (AV2)

This LCD monitor has a choice of Y, Pb, Pr or RGB H/V connections.

You can connect your DVD player to the Y, Pb, Pr terminals instead

of using a scart lead. This can support high definition in analogue

component form. RGB H/V can be used as a PC input via the BNC

terminals.Both options support a large range of resolutions (page 11).

4.

AV3

Composite (CVBS) signal input

AV3 OUT is to output the composite video signal from the

VIDEO IN so that you can connect monitors with the use of a

loop through function.

5.

RS232C IN/OUT:

Is a input for external commands to control the

monitor (see page 8).

6.

DVI-D (Digital Video Interface)

This monitor has an DVI connector. This is located at the back of the

monitor next to the phono sockets. This input will support a large

range of resolutions as shown on page 11. See page 6 for details of

menu operation.

7

PC connection

This LCD monitor has a PC connector (PC-IN D-SUB).You can

connect a PC to the LCD monitor and use it as a monitor display (see

page 7). Audio can be connected via the 3.5mm PC audio in

socket.This input will support a large range of resolutions (see pg11).

8. External Audio Output

To output the audio signal from AV 1,2,3, PC and DVI. The

speaker impedance should be 8 ohms.

■

Use of Monitor Audio Output Connections

The audio monitor out sockets on the rear of the set provide a fixed

level audio output for reproducing sound via your audio equipment.

Step : 1 Mains Connection

WARNING! High voltages are used in the operation of

this set. Refer service to qualified service personnel.

GB GB

Step : 2 Connections

AC connection

5

GB

Remote control battery installation

Install two "AA" 1.5 volt batteries so that the "+" and "-" marks on the

batteries match the "+" and "-" marks inside the unit into the remote

control handset.

1. The LCD display has a Standby light to show there is power.

Switching into/from standby mode

The Standby mode is used for switching the LCD monitor off for

short periods of time. In standby mode the monitor is switched

off but is still receiving mains power.

●

To turn the monitor into standby mode, press the

4

button.

The blue power indicator illuminates more brightly

.

●

To turn the monitor ON from standby mode, press any of the

following buttons:

4

,

5, 6

or

0-9 buttons.

2.

Control buttons (bottom edge of cabinet)

Menu/F button:

rotate between volume, Brightness, contrast,

colour, sharpness and OSD language.

Input/ OK button: s

witch between TV, AV1, RGB, AV2, AV3, DVI

and PC mode.

e d

buttons:

provide up and down adjustments

4 button:

To switch from display to standby mode (to switch off

completely disconnect the monitor from the power supply)

Many of your monitors functions are controlled through the menu

function, using the remote control handset.

During menu operation the bottom of the on screen display will show

which controls can be used for menu navigation.

Press the MENU button to enter the main menu.

A sub menu is selected using the e or d button and pressing the

1 button when the required sub menu is highlighted.

When you have finished you can press the MENU button to exit,

then the MENU button again to exit the main menu.

1. Press the MENU button. Select Picture using the e or d button.

Press the1button to enter.

Set the picture settings for your “personal” preference.

2. Use the e or d button to select eg. Brightness and the 1

2 button to adjust levels.

3. Preset : You can select either your “Personal” settings, or

Dynamic, Standard or Eco settings.

4. Noise Reduction: May be used to reduce any local picture ‘noise’

(granular appearance) being experienced by using 1 2 to

select between Mid / Max / Auto / OFF /Min.

5. Dynamic skin tone: May be used to enhance skin tone by using

1 2 to select between On / Off.

Tint : is only available if NTSC equipment is connected.

6. Text Brightness: May be adjusted by using 1 2 button to

select between Min / Mid / Max.

Press the MENU button to return to Main Menu. These settings

automatically store when you exit the menu.

Press the MENU button to exit menu.

7. Dynamic contrast (DCR): Improves the contrast leveL

✐

Your personal settings are automatically saved when you exit the

menu.

Controls and Menus

GB GB

Picture menu

Menu Operation

If you find the power indicator flashing, disconnect

power cord from the power outlet and contact our

Service desk.

This warning is a sign to let you know that the power

protection function of this TV set is now operating.

6

7

Press the MENU button and select Sound using the e or d

buttons, press the1 button to enter.

Select and adjust to obtain the best sound settings for your

environment using the e , d and 1 2 buttons.

Press the M E N U button to return to Main Menu. These settings

automatically store when you exit the menu.Press the MENU button

to exit menu.

■

OSD Language

Use the 1 or 2 button to select the prefered OSD language

(French, German, Italian, Spanish, Dutch). Press the MENU button to

exit

■

AV2 setting

In setting menu, to select AV2 press the d button and set to Y,Pb,Pr

or RGB, H/V depending on your external equipment.

1. Press the MENU button. Select Setting using the e or d button

press the 1 button to enter.

2. Select AV2 setting using the e or d button.

3. Press the 1 or 2 button to select either Y,Pb,Pr or RGB

H/V.

4. Press the MENU button to exit, this automatically stores your

changes.

5. Press the MENU button to exit.

■

Off-timer setting

The Off timer will switch the monitor into the standby mode when the

selected time has elapsed.

1. Press the MENU button. Select Setting using the e or d button

press the 1 button to enter.

2. Select Timer using the e or d button, press 1 button to enter.

3. Press the 1 or 2button to change time.

The time changes in 5 minute steps.The maximum time is 120 min-

utes.

If you have set the off timer, a count down display appears in the

corner of the screen when the recall button is pressed.

✐

If the monitor is switched off by the standby button 4 on the

remote control or by the standby switch 4 on the bottom of the

LCD monitor the timer settings will be cancelled.

Connect your PC to either PC-IN or RGBHV or DVI on the rear of the

set. Once connected select PC mode or AV2 (RGBHV, see page 4

for AV2 input settings)or DVI via the v button on your remote

control. The set will become a monitor for the PC.

By pressing the MENU button on the remote control a menu window

will appear on screen, this allows the settings to be adjusted.

To adjust the Picture settings select picture using the e or d buttons

on the remote then the1 button to enter the following picture

settings menu.

Press the 1 or 2 buttons to adjusted the Picture brightness

and the same to adjust the contrast of the picture.

Picture position changes the picture horizontally or vertically. Press

the1 button to enter the sub menus, adjustment is carried out

using the1 or 2 buttons on the remote control.

Video adjust changes the Phase and the clock of the screen. If the

picture is blurred or grainy this function will adjust it to a clearer

picture, adjustment is carried out using the 1 or 2 buttons on

the remote control.

Auto Adjust will automatically adjust the picture by using the

1 button.This will change all the above settings automatically.

Auto adjust can also be achieved by pressing the /recall

button on the remote control without having to select the menu (not

included in DVI mode)

Resolution displays the current resolution of the picture. This is for

information only and cannot be adjusted.

White tone: Using the 1or2 buttons it is possible to adjust

the colour tone of the picture using the White tone Red(R) / Green

(G)/ Blue(B). This will adjust the picture to show more or less of the

chosen colour. For example if red is selected you can adjust the pro

portion of red in the picture to increase or decrease using the 1

or 2 buttons

Native Resolution is used when the PC can output WXGA 1366 x

768. The setting on your Monitor set can be changed to receive

XGA/WXGA signal using the1 or 2 buttons . Once the native

resolution has been selected, save the settings by switching the

monitor off then on using the standby button.

For Sound settings refer to previous menu

Setting: Press the menu button on your remote and using the e or

d buttons to select Settings. The 1 button will enter the settings

menu.

Timer and AV2 settings are the same as in all other input modes

(pg 7).

Power save if turned ON will switch the monitor into Powersave

mode after 1 minute if no signal is detected, the LED light will turn a

brighter blue to indicate stand by. The monitor will automatically turn

back on when a signal has been detected (PC input / RGBHV).

Use1 or 2 buttons to select power save ON or OFF.

Setting menu

GB

PC menu settings

Sound menu

8

This monitor can be controlled via the RS232C connector using a

suitable computer/ control commands.

Serial Interface Specification

Transfer Specification

1. Transmission Speed: initial setting value is 19200.

2. Transmission speed can be changed via the Installation menu

(see below baud rate)

Connection

The Designated RS-232C serial cable must be used for a

connection to a computer and LCD monitor.

The TV command is defined by one command/ one line that starts

with “C” and ends with carriage return. (0x0D)

There are two types of commands:

Functional Execution Command e.g Co5[CR] (table on page 63)

Status Read Commands e.g “CR0 [CR] (see table on page 63)

Setting the monitor address in RS232 mode

To Access Installation mode press the green button on the remote

control and hold for 5 seconds. A new screen will appear.

Each monitor can have a specific Address for example 007, which

enables the monitor to be controlled individually and will not affect

other monitors connected to a controlling PC.

Address format command

The addressing format command is used for operating multiple

monitor sets from a single PC via the RS232C command line. If you

set your monitor address to ‘000’, it will never respond to any

addressing command from the PC.

If the address from the PC is ‘FFF’, all monitor sets will execute the

command.

The Address format command is defined by one command, one line

which starts with ‘A’ and ends with carriage return.(0 x0D)

The Monitor starts to decode when it receives a carriage return.

(0x0D)

An address is added at the top of a control command

Example:

Functional execution command:

“A001C05” [CR] means address is 001 and the control command is

C05

Status read command

“A001CR0”[CR] means address is 001 and command is CR0.

The monitor can set its own address in the Installation option menu

(above) The address range is 000 - 999, the default address will be

000

The baud rate indicates the unit for transfer speed of data

from the PC to the monitor sets

This LCD monitor allows you to set up the following:-

■ Programme position at Start up

SETTING PROCEDURE

1 . Press and hold the green button on the Remote control

handset for 5 seconds.(Installation menu will appear)

2.

Use the 5 or 6 button to highlight each option, use the

1 or

2

to switch between each option.

■

On Program

Select ON program using the

6 button, select the start up position

using the

1 or 2 buttons.

(Off / AV1 / RGB/ AV2/ AV3/ DVI/ PC)

Press the MENU button to exit the menu.

■

Max Volume

Select Max volume using the

6 button, use the

1 or 2

buttons to set the maximum volume required.

■

OSD (On screen display)

Select OSD using the

6 button, select ON / OFF using the

1 or

2 buttons.Selecting OFF will inhibit the OSD. To re-instate OSD,

press and hold the green button on the remote control to re-enter

installation menu and select OSD ON.

■

Winter mode

This Function can be activated when the LCD monitor is used during

cold temperature conditions, approximately 38˚F/ 4˚C or below to

maintain picture performance.

Using the e or d button select winter mode, once highlighted you

can select ON or OFF by pressing the 1 or 2 button.

IMPORTANT: The AC cord should not be disconnected during the

operation of Winter mode function.

When in winter mode, power consumption is higher than normal

standby consumption. This is entirely due to the operation of heating

circuitry. We strongly recommend to turn off Winter mode when the

ambient temperature is above 38˚F/ 4˚C.

■

RC Inhibition

You can prevent unwanted remote control operation by selecting RC

Inhibition. When selected an inhibit symbol will appear on screen

when a button is pressed on the remote control.

Select using the e or d button. Press the 1 or 2 button to

select On or OFF.

To re-instate RC operation press and hold the green button on the

remote control and select RC inhibition OFF.

■

Child lock

You can prevent unwanted operation of the LCD monitor via the

buttons on the bottom edge of the monitor.

Select using the e or d button. Press the 1 button to select On

or OFF.

✐

Disconnecting the mains suppy will cancel this feature.

GB

RS232C settings

Installation Menu

Page is loading ...

10

Common specification

Power source 220~240V 50Hz

Colour system PAL NTSC3.5 ,SECAM

AV terminal

AV1: Scart CENELEC Standard

Input: Composite video, RGB (5V RGB with 5V sync to

pin 14) and audio-L/R

AV2: BNC

Input: RGB, H and V / Y, Pb, Pr and audio L/R

Output: RGB, H and V / Y, Pb, Pr

AV3: BNC

Input: Composite video

Output : Composite video

Audio Monitor.Out: CINCH L/R

Audio Speaker out: 2 x 6W

DVI Input : DVI-D GROUP Standard

PC Input: Mini D-SUB 15 PIN and

Audio 3.5mm Jack

Serial port: RS232C: Input/Output

Contrast Ratio 1000:1

Screen(inches/ cm) 42” / 107 cm

(viewing measured

diagonally)

Display Native Resolution 1366 x 768 (WXGA)

Viewing angles H:178°, V:178°

Dimensions (WxHxDmm) 1032x 625x126.5 (without stand)

1032 x 683 x 340 (with stand)

Weight (kg) 20 (without stand)

21 (With stand)

■

NO PICTURE, NO SOUND

●

Check if monitor is plugged in.

● Check monitor is not in standby mode

■

POOR PICTURE, SOUND OK

●

Adjust BRIGHTNESS/ CONTRAST LEVELS (too low).

■

NO COLOUR, PICTURE OK

●

Adjust COLOUR control.

●

Check lead connections

●

Does the signal input have colour

■

REMOTE CONTROL DOES NOT WORK

●

Check batteries are inserted correctly

●

Check condition of batteries

●

Check to see if remote control inhibit is set ON

■

PICTURE OK, NO SOUND

●

Check external speakers are connected correctly

●

Check lead connections to external equipment

●

Volume turned down or mute selected

GB

Specification

Helpful hints

11

PC/DVI-D / COMPONENT SIGNAL SUPPORT TIMING LIST

GB GB

Page is loading ...

62

COMPONENT SIGNAL SUPPORT TIMING LIST

63

RS-232C COMMAND TABLES

64

Part No. 1KA6P1P0436-- N4GT

Printed in U.K.

Sanyo 42SRE1 User manual

This manual is also suitable for

Sanyo 42SRE1 User manual

in other languages

Related papers

Other documents